Abstract: This study was aimed to investigate the machining
stability of a spindle tool with different preloaded amount. To this end,
the vibration tests were conducted on the spindle unit with different
preload to assess the dynamic characteristics and machining stability
of the milling machine. Current results demonstrate that the tool tip
frequency response characteristics and the machining stabilities in X
and Y direction are affected to change due to the different preload of
spindle bearings. As found from the results, a high preloaded spindle
tool shows higher limited cutting depth at mid position, while a spindle
with low preload shows a higher limited depth. This indicates that the
machining stability of a milling machine is affected to vary by the
spindle unit when it was assembled with different bearing preload.
Abstract: This paper presents the variation of the dynamic
characteristics of a spindle with the change of bearing preload. The
correlations between the variation of bearing preload and fundamental
modal parameters were first examined by conducting vibration tests on
physical spindle units. Experimental measurements show that the
dynamic compliance and damping ratio associated with the
dominating modes were affected to vary with variation of the bearing
preload. When the bearing preload was slightly deviated from a
standard value, the modal frequency and damping ability also vary to
different extent, which further enable the spindle to perform with
different compliance. For the spindle used in this study, a standard
preload value set on bearings would enable the spindle to behave a
higher stiffness as compared with others with a preload variation. This
characteristic can be served as a reference to examine the variation of
bearing preload of spindle in assemblage or operation.
Abstract: This study presented the investigation of the influence of the tool holder interface stiffness on the dynamic characteristics of a spindle tool system. The interface stiffness was produced by drawbar force on the tool holder, which tends to affect the spindle dynamics. In order to assess the influence of interface stiffness on the vibration characteristic of spindle unit, we first created a three dimensional finite element model of a high speed spindle system integrated with tool holder. The key point for the creation of FEM model is the modeling of the rolling interface within the angular contact bearings and the tool holder interface. The former can be simulated by a introducing a series of spring elements between inner and outer rings. The contact stiffness was calculated according to Hertz contact theory and the preload applied on the bearings. The interface stiffness of the tool holder was identified through the experimental measurement and finite element modal analysis. Current results show that the dynamic stiffness was greatly influenced by the tool holder system. In addition, variations of modal damping, static stiffness and dynamic stiffness of the spindle tool system were greatly determined by the interface stiffness of the tool holder which was in turn dependent on the draw bar force applied on the tool holder. Overall, this study demonstrates that identification of the interface characteristics of spindle tool holder is of very importance for the refinement of the spindle tooling system to achieve the optimum machining performance.
Abstract: The machining performance is determined by the
frequency characteristics of the machine-tool structure and the
dynamics of the cutting process. Therefore, the prediction of dynamic
vibration behavior of spindle tool system is of great importance for the
design of a machine tool capable of high-precision and high-speed
machining. The aim of this study is to develop a finite element model
to predict the dynamic characteristics of milling machine tool and
hence evaluate the influence of the preload of the spindle bearings. To
this purpose, a three dimensional spindle bearing model of a high
speed engraving spindle tool was created. In this model, the rolling
interfaces with contact stiffness defined by Harris model were used to
simulate the spindle bearing components. Then a full finite element
model of a vertical milling machine was established by coupling the
spindle tool unit with the machine frame structure. Using this model,
the vibration mode that had a dominant influence on the dynamic
stiffness was determined. The results of the finite element simulations
reveal that spindle bearing with different preloads greatly affect the
dynamic behavior of the spindle tool unit and hence the dynamic
responses of the vertical column milling system. These results were
validated by performing vibration on the individual spindle tool unit
and the milling machine prototype, respectively. We conclude that
preload of the spindle bearings is an important component affecting
the dynamic characteristics and machining performance of the entire
vertical column structure of the milling machine.
Abstract: Chatter vibration has been a troublesome problem for a
machine tool toward the high precision and high speed machining.
Essentially, the machining performance is determined by the dynamic
characteristics of the machine tool structure and dynamics of cutting
process. Therefore the dynamic vibration behavior of spindle tool
system greatly determines the performance of machine tool. The
purpose of this study is to investigate the influences of the machine
frame structure on the dynamic frequency of spindle tool unit through
finite element modeling approach. To this end, a realistic finite
element model of the vertical milling system was created by
incorporated the spindle-bearing model into the spindle head stock of
the machine frame. Using this model, the dynamic characteristics of
the milling machines with different structural designs of spindle head
stock and identical spindle tool unit were demonstrated. The results of
the finite element modeling reveal that the spindle tool unit behaves
more compliant when the excited frequency approaches the natural
mode of the spindle tool; while the spindle tool show a higher dynamic
stiffness at lower frequency that may be initiated by the structural
mode of milling head. Under this condition, it is concluded that the
structural configuration of spindle head stock associated with the
vertical column of milling machine plays an important role in
determining the machining dynamics of the spindle unit.