Abstract: An experimental and numerical study has been conducted to clarify heat transfer characteristics and effectiveness of a cross-flow heat exchanger employing staggered wing-shaped tubes at different angels of attack. The water-side Rew and the air-side Rea were at 5 x 102 and at from 1.8 x 103 to 9.7 x 103, respectively. The tubes arrangements were employed with various angles of attack θ1,2,3 from 0° to 330° at the considered Rea range. Correlation of Nu, St, as well as the heat transfer per unit pumping power (ε) in terms of Rea, design parameters for the studied bundle were presented. The temperature fields around the staggered wing-shaped tubes bundle were predicted by using commercial CFD FLUENT 6.3.26 software package. Results indicated that the heat transfer was increased by increasing the angle of attack from 0° to 45°, while the opposite was true for angles of attack from 135° to 180°. The best thermal performance and hence η of studied bundle was occurred at the lowest Rea and/or zero angle of attack. Comparisons between the experimental and numerical results of the present study and those, previously, obtained for similar available studies showed good agreements.
Abstract: The application of a Static Synchronous Series Compensator (SSSC) controller to improve the transient stability performance of a power system is thoroughly investigated in this paper. The design problem of SSSC controller is formulated as an optimization problem and Particle Swarm Optimization (PSO) Technique is employed to search for optimal controller parameters. By minimizing the time-domain based objective function, in which the deviation in the oscillatory rotor angle of the generator is involved; transient stability performance of the system is improved. The proposed controller is tested on a weakly connected power system subjected to different severe disturbances. The non-linear simulation results are presented to show the effectiveness of the proposed controller and its ability to provide efficient damping of low frequency oscillations. It is also observed that the proposed SSSC controller improves greatly the voltage profile of the system under severe disturbances.
Abstract: Adhesively bonded joints are preferred over the
conventional methods of joining such as riveting, welding, bolting
and soldering. Some of the main advantages of adhesive joints
compared to conventional joints are the ability to join dissimilar
materials and damage-sensitive materials, better stress distribution,
weight reduction, fabrication of complicated shapes, excellent
thermal and insulation properties, vibration response and enhanced
damping control, smoother aerodynamic surfaces and an
improvement in corrosion and fatigue resistance. This paper presents
the behavior of adhesively bonded joints subjected to combined
thermal loadings, using the numerical methods. The joint
configuration considers aluminum as central adherend with six
different outer adherends including aluminum, steel, titanium, boronepoxy,
unidirectional graphite-epoxy and cross-ply graphite-epoxy
and epoxy-based adhesives. Free expansion of the joint in x
direction was permitted and stresses in adhesive layer and interfaces
calculated for different adherends.
Abstract: This study proposes a conceptual model and
empirically tests the relationships between customers and librarians
(i.e. tangibles, responsiveness, assurance, reliability and empathy)
with a dependent variable (customer satisfaction) regarding library
services. The SERVQUAL instrument was administered to 100
respondents which comprises of staff and students at a public higher
learning institution in the Federal Territory of Labuan, Malaysia.
They were public university library users. Results revealed that all
service quality dimensions tested were significant and influenced
customer satisfaction of visitors to a public university library.
Assurance is the most important factor that influences customer
satisfaction with the services rendered by the librarian. It is
imperative for the library management to take note that the top five
service attributes that gained greatest attention from library visitors-
perspective includes employee willingness to help customers,
availability of customer representatives online for response to
queries, library staff actively and promptly provide services, signs in
the building are clear and library staff are friendly and courteous.
This study provides valuable results concerning the determinants of
the service quality and customer satisfaction of public university
library services from the users' perspective.
Abstract: the aim of this study was to analyze ethnopsychological content of “Aitys" as a process of creative competition in Kazakh traditional folklore by means of Transaction analysis (three types of Ego states are Parent, Adult and Child). “Aitys" is as sources of Kazakh national self-consciousness and form of oral Kazakh national creativity. Comparative psychological analysis of classical and modern “aityses" is carried out. Empirical proved that the victory in “Aitys" is provided with a position of egostate “Adult".
Abstract: The aim of this paper is to provide an empirical
evidence about the effects that the management of continuous
training have on employability (or employment stability) in the
Spanish labour market. With this purpose a binary logit model with
interaction effect is been used. The dependent variable includes two
situations of the active workers: continuous and discontinuous
employability. To distinguish between them an Employability Index
Stability (ESI) was calculated taking into account two factors: time
worked and job security. Various aspects of the continuous training
and personal workers data are used as independent variables. The
data obtained from a survey of a sample of 918 employed have
revealed a relationship between the likelihood of continuous
employability and continuous training received. The empirical results
support the positive and significant relationship between various
aspects of the training provided by firms and employability
likelihood of the workers, postulate alike from a theoretical point of
view.
Abstract: When consistently innovative business-models can
give companies a competitive advantage, longitudinal empirical
research, which can reflect dynamic business-model changes, has yet
to prove a definitive connection. This study consequently employs a
dynamic perspective in conjunction with innovation theory to examine
the relationship between the types of business-model innovation and
firm value. This study tries to examine various types of
business-model innovation in high-end and low-end technology
industries such as HTC and the 7-Eleven chain stores with research
periods of 14 years and 32 years, respectively. The empirical results
suggest that adopting radical business-model innovation in addition to
expanding new target markets can successfully lead to a competitive
advantage. Sustained advanced technological competences and
service/product innovation are the key successful factors in high-end
and low-end technology industry business-models respectively. In
sum up, the business-model innovation can yield a higher market value
and financial value in high-end technology industries than low-end
ones.
Abstract: Organizational innovation favors technological
innovation, but does it also influence technological innovation
persistence? This article investigates empirically the pattern of
technological innovation persistence and tests the potential impact of
organizational innovation using firm-level data from three waves of
the French Community Innovation Surveys. Evidence shows a
positive effect of organizational innovation on technological
innovation persistence, according to various measures of
organizational innovation. Moreover, this impact is more significant
for complex innovators (i.e., those who innovate in both products and
processes). These results highlight the complexity of managing
organizational practices with regard to the firm-s technological
innovation. They also add to comprehension of the drivers of
innovation persistence, through a focus on an often forgotten
dimension of innovation in a broader sense.
Abstract: There are only limited studies that directly correlate
the increase in reinforced concrete (RC) panel structural capacities in
resisting the blast loads with different RC panel structural properties
in terms of blast loading characteristics, RC panel dimensions, steel
reinforcement ratio and concrete material strength. In this paper,
numerical analyses of dynamic response and damage of the one-way
RC panel to blast loads are carried out using the commercial software
LS-DYNA. A series of simulations are performed to predict the blast
response and damage of columns with different level and magnitude
of blast loads. The numerical results are used to develop pressureimpulse
(P-I) diagrams of one-way RC panels. Based on the
numerical results, the empirical formulae are derived to calculate the
pressure and impulse asymptotes of the P-I diagrams of RC panels.
The results presented in this paper can be used to construct P-I
diagrams of RC panels with different concrete and reinforcement
properties. The P-I diagrams are very useful to assess panel capacities
in resisting different blast loads.
Abstract: We present the development of a system of programs designed for the compilation and execution of applications for handheld computers. In introduction we describe the purpose of the project and its components. The next two paragraphs present the first two components of the project (the scanner and parser generators). Then we describe the Object Pascal compiler and the virtual machines for Windows and Palm OS. In conclusion we emphasize the ways in which the project can be extended.
Abstract: Unlike general-purpose processors, digital signal
processors (DSP processors) are strongly application-dependent. To
meet the needs for diverse applications, a wide variety of DSP
processors based on different architectures ranging from the
traditional to VLIW have been introduced to the market over the
years. The functionality, performance, and cost of these processors
vary over a wide range. In order to select a processor that meets the
design criteria for an application, processor performance is usually
the major concern for digital signal processing (DSP) application
developers. Performance data are also essential for the designers of
DSP processors to improve their design. Consequently, several DSP
performance benchmarks have been proposed over the past decade or
so. However, none of these benchmarks seem to have included recent
new DSP applications.
In this paper, we use a new benchmark that we recently developed
to compare the performance of popular DSP processors from Texas
Instruments and StarCore. The new benchmark is based on the
Selectable Mode Vocoder (SMV), a speech-coding program from the
recent third generation (3G) wireless voice applications. All
benchmark kernels are compiled by the compilers of the respective
DSP processors and run on their simulators. Weighted arithmetic
mean of clock cycles and arithmetic mean of code size are used to
compare the performance of five DSP processors.
In addition, we studied how the performance of a processor is
affected by code structure, features of processor architecture and
optimization of compiler. The extensive experimental data gathered,
analyzed, and presented in this paper should be helpful for DSP
processor and compiler designers to meet their specific design goals.
Abstract: This paper presents an exploration into the structure of the corporate governance network and interlocking directorates in the Czech Republic. First a literature overview and a basic terminology of the network theory is presented. Further in the text, statistics and other calculations relevant to corporate governance networks are presented. For this purpose an empirical data set consisting of 2 906 joint stock companies in the Czech Republic was examined. Industries with the highest average number of interlocks per company were healthcare, and energy and utilities. There is no observable link between the financial performance of the company and the number of its interlocks. Also interlocks with financial companies are very rare.
Abstract: This study defines a methodology to compute unitary costs for freight transportation modes. The main objective was to gather relevant costs data to support the formulation and evaluation of railway, road, pipelines and port projects. This article will concentrate on the following steps: Compilation and analysis of relevant modal cost studies, Methodological adjustments to make cost figures comparable between studies, Definition of typology and scope of transportation modes, Analysis and validation of cost values for relevant freight transportation modes in Chile. In order to define the comparison methodology for the costs between the different transportation modes, it was necessary to consider that the relevant cost depends on who performs the comparison. Thus, for the transportation user (e.g. exporter) the pertinent costs are the mode tariffs, whereas from the operators perspective (e.g. rail manager), the pertinent costs are the operating costs of each mode.
Abstract: The integral form of equations of motion of composite
beams subjected to varying time loads are discretized using a
developed finite element model. The model consists of a straight five
node twenty-two degrees of freedom beam element. The stability
analysis of the beams is studied by solving the matrix form
characteristic equations of the system. The principle of virtual work
and the first order shear deformation theory are employed to analyze
the beams with large deformation and small strains. The regions of
dynamic instability of the beam are determined by solving the
obtained Mathieu form of differential equations. The effects of nonconservative
loads, shear stiffness, and damping parameters on
stability and response of the beams are examined. Several numerical
calculations are presented to compare the results with data reported
by other researchers.
Abstract: In this paper the complete rotor system including
elastic shaft with distributed mass, allowing for the effects of oil film
in bearings. Also, flexibility of foundation is modeled. As a whole
this article is a relatively complete research in modeling and
vibration analysis of rotor considering gyroscopic effect, damping,
dependency of stiffness and damping coefficients on frequency and
solving the vibration equations including these parameters. On the
basis of finite element method and utilizing four element types
including element of shaft, disk, bearing and foundation and using
MATLAB, a computer program is written. So the responses in
several cases and considering different effects are obtained. Then the
results are compared with each other, with exact solutions and results
of other papers.
Abstract: In this paper, parallelism in the solution of Ordinary
Differential Equations (ODEs) to increase the computational speed is
studied. The focus is the development of parallel algorithm of the two
point Block Backward Differentiation Formulas (PBBDF) that can
take advantage of the parallel architecture in computer technology.
Parallelism is obtained by using Message Passing Interface (MPI).
Numerical results are given to validate the efficiency of the PBBDF
implementation as compared to the sequential implementation.
Abstract: The major building block of most elliptic curve cryptosystems
are computation of multi-scalar multiplication. This paper
proposes a novel algorithm for simultaneous multi-scalar multiplication,
that is by employing addition chains. The previously known
methods utilizes double-and-add algorithm with binary representations.
In order to accomplish our purpose, an efficient empirical
method for finding addition chains for multi-exponents has been
proposed.
Abstract: MC (Management Control)& IC (Internal Control) – what is the relationship? (an empirical study into the definitions between MC and IC) based on the wider considerations of Internal Control and Management Control terms, attention is focused not only on the financial aspects but also more on the soft aspects of the business, such as culture, behaviour, standards and values. The limited considerations of Management Control are focused mainly in the hard, financial aspects of business operation. The definitions of Management Control and Internal Control are often used interchangeably and the results of this empirical study reveal that Management Control is part of Internal Control, there is no causal link between the two concepts. Based on the interpretation of the respondents, the term Management Control has moved from a broad term to a more limited term with the soft aspects of the influencing of behaviour, performance measurements, incentives and culture. This paper is an exploratory study based on qualitative research and on a qualitative matrix method analysis of the thematic definition of the terms Management Control and Internal Control.
Abstract: Detection of incipient abnormal events is important to
improve safety and reliability of machine operations and reduce losses
caused by failures. Improper set-ups or aligning of parts often leads to
severe problems in many machines. The construction of prediction
models for predicting faulty conditions is quite essential in making
decisions on when to perform machine maintenance. This paper
presents a multivariate calibration monitoring approach based on the
statistical analysis of machine measurement data. The calibration
model is used to predict two faulty conditions from historical reference
data. This approach utilizes genetic algorithms (GA) based variable
selection, and we evaluate the predictive performance of several
prediction methods using real data. The results shows that the
calibration model based on supervised probabilistic principal
component analysis (SPPCA) yielded best performance in this work.
By adopting a proper variable selection scheme in calibration models,
the prediction performance can be improved by excluding
non-informative variables from their model building steps.
Abstract: Cement stabilization has been widely used for
improving the strength and stiffness of soft clayey soils. Cement
treated soil specimens used to investigate the stress-strain behaviour in
the laboratory study are usually cured for 7 days. This paper examines
the effects of curing time on the strength and stress strain behaviour of
cement treated marine clay under triaxial loading condition.
Laboratory-prepared cement treated Singapore marine clay with
different mix proportion S-C-W (soil solid-cement solid-water) and
curing time (7 days to 180 days) was investigated through conducting
unconfined compressive strength test and triaxial test. The results
show that the curing time has a significant effect on the unconfined
compressive strength u q , isotropic compression behaviour and stress
strain behaviour. Although the primary yield loci of the cement treated
soil specimens with the same mix proportion expand with curing time,
they are very narrowly banded and have nearly the same shape after
being normalized by isotropic compression primary stress '
py p . The
isotropic compression primary yield stress '
py p was shown to be
linearly related to unconfined compressive strength u q for specimens
with different curing time and mix proportion. The effect of curing
time on the hardening behaviour will diminish with consolidation
stress higher than isotropic compression primary yield stress but its
damping rate is dependent on the cement content.