Abstract: Most buildings have been using anchor bolts
commonly for installing outdoor advertising structures. Anchor bolts
of common carbon steel are widely used and often installed
indiscriminately by inadequate installation standards. In the area
where strong winds frequently blow, falling accidents of outdoor
advertising structures can occur and cause a serious disaster, which is
very dangerous and to be prevented. In this regard, the development of
high-performance anchor bolts is urgently required. In the present
study, 25Cr-8Ni-1.5Si-1Mn-0.4C alloy was produced by traditional
vacuum induction melting (VIM) for the application of anchor bolt.
The alloy composition is revealed as a duplex microstructure from
thermodynamic phase analysis by FactSage® and confirmed by
metallographic experiment. Addition of Nitrogen to the alloy was
found to reduce the ferritic phase domain and significantly increase the
hardness and the tensile strength. Microstructure observation revealed
mixed structure of austenite and ferrite with fine carbide distributed
along the grain and phase boundaries.
Abstract: The hot deformation behavior of high strength low
alloy (HSLA) steels with different chemical compositions under hot
working conditions in the temperature range of 900 to 1100℃ and
strain rate range from 0.1 to 10 s-1 has been studied by performing a
series of hot compression tests. The dynamic materials model has been
employed for developing the processing maps, which show variation
of the efficiency of power dissipation with temperature and strain rate.
Also the Kumar-s model has been used for developing the instability
map, which shows variation of the instability for plastic deformation
with temperature and strain rate. The efficiency of power dissipation
increased with decreasing strain rate and increasing temperature in the
steel with higher Cr and Ti content. High efficiency of power
dissipation over 20 % was obtained at a finite strain level of 0.1 under
the conditions of strain rate lower than 1 s-1 and temperature higher
than 1050 ℃ . Plastic instability was expected in the regime of
temperatures lower than 1000 ℃ and strain rate lower than 0.3 s-1. Steel
with lower Cr and Ti contents showed high efficiency of power
dissipation at higher strain rate and lower temperature conditions.
Abstract: The purpose of this study was to examine the viewpoints in terms of changing distances and levels and thereby, comparatively analyze the visual sensitivity to the elements of the natural views. The questionnaire survey was conducted separately for experts and non-experts. Summing up, it was confirmed that the visual sensitivity to the elements of the same natural views differed significantly depending on subjects' professionalism, changes of the viewpoint levels and distances, while the visual sensitivity to 'openness of visual/view axes' did not differ significantly when only the distances of the viewpoints were varied. In addition, the visual sensitivity to visual/view axes differed between experts and ordinary people when the levels of the viewpoints were varied, while the visual sensitivity to 'damaged natural view resources' differed between two groups when the distances of the viewpoints were varied.
Abstract: In this paper, we proposed a method to reduce
quantization error. In order to reduce quantization error, low pass
filtering is applied on neighboring samples of current block in
H.264/AVC. However, it has a weak point that low pass filtering is
performed regardless of prediction direction. Since it doesn-t consider
prediction direction, it may not reduce quantization error effectively.
Proposed method considers prediction direction for low pass filtering
and uses a threshold condition for reducing flag bit. We compare our
experimental result with conventional method in H.264/AVC and we
can achieve the average bit-rate reduction of 1.534% by applying the
proposed method. Bit-rate reduction between 0.580% and 3.567% are
shown for experimental results.
Abstract: This paper presents an effective method for detecting vehicles in front of the camera-assisted car during nighttime driving. The proposed method detects vehicles based on detecting vehicle headlights and taillights using techniques of image segmentation and clustering. First, to effectively extract spotlight of interest, a segmentation process based on automatic multi-level threshold method is applied on the road-scene images. Second, to spatial clustering vehicle of detecting lamps, a grouping process based on light tracking and locating vehicle lighting patterns. For simulation, we are implemented through Da-vinci 7437 DSP board with near infrared mono-camera and tested it in the urban and rural roads. Through the test, classification performances are above 97% of true positive rate evaluated on real-time environment. Our method also has good performance in the case of clear, fog and rain weather.
Abstract: This paper presents an iterative algorithm to find a
inverse kinematic solution of 5-DOF robot. The algorithm is to
minimize the iteration number. Since the 5-DOF robot cannot give full
orientation of tool. Only z-direction of tool is satisfied while rotation
of tool is determined by kinematic constraint. This work therefore
described how to specify the tool direction and let the tool rotation free.
The simulation results show that this algorithm effectively worked.
Using the proposed iteration algorithm, error due to inverse kinematics
converged to zero rapidly in 5 iterations. This algorithm was applied in
real welding robot and verified through various practical works.
Abstract: The primary objective of this research is to improve the flexural capacity of FRP strengthened RC Beam structures with Aluminum and Titanium laminates. FRP rupture of flexural strengthened RC beams using FRP plates generally occurs at the interface between FRP plate and the beam. Therefore, in order to prevent brittle rupture and improve the ductility of the system, this research was performed by using Aluminum and Titanium materials between the two different structural systems. The research also aims to provide various strengthening/retrofitting methods for RC beam structures and to conduct a preliminary analysis of the demands on the structural systems. This was achieved by estimation using the experimental data from this research to identify a flexural capacity for the systems. Ultimately, the preliminary analysis of current study showed that the flexural capacity and system demand ductility was significantly improved by the systems inserted with Aluminum and Titanium anchor plates. Further verification of the experimental research is currently on its way to develop a new or reliable design guideline to retrofit/strengthen the concrete-FRP structural system can be evaluated.
Abstract: Firstly, research and development on RFID focuses on
manufacturing and retail sectors, because it can improve supply chain
efficiency. But, now a variety of field is considered the next research
area for Radio Frequency Identification (RFID). Although RFID is
infancy, RFID technology has great potential in power industry to
significantly reduce cost, and improve quality of power supply. To
complement the limitation of RFID, we adopt the WSN (Wireless
Sensor Network) technology. However, relevant experience is limited,
the challenge will be to derive requirement from business practice and
to determine whether it is possible or not. To explore this issue, we
conduct a case study on implementing power facility management
system using RFID/WSN in Korea Electric Power Corporation
(KEPCO). In this paper we describe requirement from power industry.
And we introduce design and implementation of the test bed.
Abstract: The purpose of this research was develop a biological
nutrient removal (BNR) system which has low energy consumption, sludge production, and land usage. These indicate that BNR system could be a alternative of future wastewater treatment in ubiquitous
city(U-city). Organics and nitrogen compounds could be removed by this system so that secondary or tertiary stages of wastewater treatment satisfy their standards. This system was composed of oxic and anoxic
filter filed with PVDC and POM media. Anoxic/oxic filter system operated under empty bed contact time of 4 hours by increasing
recirculation ratio from 0 to 100 %. The system removals of total nitrogen and COD were 76.3% and 93%, respectively. To be observed
internal behavior in this system SCOD, NH3-N, and NO3-N were
conducted and removal shows range of 25~100%, 59~99%, and
70~100%, respectively.
Abstract: The Virtual Reality (VR) is becoming increasingly
important for business, education, and entertainment, therefore VR
technology have been applied for training purposes in the areas of
military, safety training and flying simulators. In particular, the
superior and high reliability VR training system is very important in
immersion. Manipulation training in immersive virtual environments
is difficult partly because users must do without the hap contact with
real objects they rely on in the real world to orient themselves and
their manipulated.
In this paper, we create a convincing questionnaire of immersion
and an experiment to assess the influence of immersion on
performance in VR training system. The Immersion Questionnaire
(IQ) included spatial immersion, Psychological immersion, and
Sensory immersion. We show that users with a training system
complete visual attention and detection of signals. Twenty subjects
were allocated to a factorial design consisting of two different VR
systems (Desktop VR and Projector VR). The results indicated that
different VR representation methods significantly affected the
participants- Immersion dimensions.
Abstract: This paper presents a method for functional projective H∞ synchronization problem of chaotic systems with external disturbance. Based on Lyapunov theory and linear matrix inequality (LMI) formulation, the novel feedback controller is established to not only guarantee stable synchronization of both drive and response systems but also reduce the effect of external disturbance to an H∞ norm constraint.
Abstract: Biological data has several characteristics that strongly differentiate it from typical business data. It is much more complex, usually large in size, and continuously changes. Until recently business data has been the main target for discovering trends, patterns or future expectations. However, with the recent rise in biotechnology, the powerful technology that was used for analyzing business data is now being applied to biological data. With the advanced technology at hand, the main trend in biological research is rapidly changing from structural DNA analysis to understanding cellular functions of the DNA sequences. DNA chips are now being used to perform experiments and DNA analysis processes are being used by researchers. Clustering is one of the important processes used for grouping together similar entities. There are many clustering algorithms such as hierarchical clustering, self-organizing maps, K-means clustering and so on. In this paper, we propose a clustering algorithm that imitates the ecosystem taking into account the features of biological data. We implemented the system using an Ant-Colony clustering algorithm. The system decides the number of clusters automatically. The system processes the input biological data, runs the Ant-Colony algorithm, draws the Topic Map, assigns clusters to the genes and displays the output. We tested the algorithm with a test data of 100 to1000 genes and 24 samples and show promising results for applying this algorithm to clustering DNA chip data.
Abstract: This paper proposes the method combining artificial
neural network (ANN) with particle swarm optimization (PSO) to
implement the maximum power point tracking (MPPT) by controlling
the rotor speed of the wind generator. First, the measurements of wind
speed, rotor speed of wind power generator and output power of wind
power generator are applied to train artificial neural network and to
estimate the wind speed. Second, the method mentioned above is
applied to estimate and control the optimal rotor speed of the wind
turbine so as to output the maximum power. Finally, the result reveals
that the control system discussed in this paper extracts the maximum
output power of wind generator within the short duration even in the
conditions of wind speed and load impedance variation.
Abstract: In this paper, a novel LVTSCR-based device for
electrostatic discharge (ESD) protection of integrated circuits (ICs) is
designed, fabricated and characterized. The proposed device is similar
to the conventional LVTSCR but it has an embedded PMOSFET in the
anode n-well to enhance the turn on speed, the clamping capability and
the robustness. This is possible because the embedded PMOSFET
provides the sub-path of ESD discharge current. The TLP, HBM and
MM testing are carried out to verify the ESD performance of the
proposed devices, which are fabricated in 0.35um
(Bipolar-CMOS-DMOS) BCDMOS process. The device has the
robustness of 70mA/um that is higher about 60mA/um than the
LVTSCR, approximately.
Abstract: Although there are many theories and discussion of leadership, the necessity of having a new leadership paradigm was emphasized. The existing leadership characteristic of instruction and control revealed its limitations. Market competition becomes fierce and economic recession never ends worldwide. Of the leadership theories, servant leadership was introduced recently and is in line with the environmental changes of the organization. Servant leadership is a combination of two words, 'servant' and 'leader' and can be defined as the role of the leader who focuses on doing voluntary work for others with altruistic ethics, makes members, customers, and local communities a priority, and makes a commitment to satisfying their needs. This leadership received attention as one field of leadership in the late 1990s and secured its legitimacy. This study discusses the existing research trends of leadership, the concept, behavior characteristics, and lower dimensions of servant leadership, compares servant leadership with the existing leadership researches and diagnoses if servant leadership is a useful concept for further leadership researches. Finally, this study criticizes the limitations in the existing researches on servant leadership.
Abstract: This paper presents a novel approach for representing
the spatio-temporal topology of the camera network with overlapping
and non-overlapping fields of view (FOVs). The topology is
determined by tracking moving objects and establishing object
correspondence across multiple cameras. To track people successfully
in multiple camera views, we used the Merge-Split (MS) approach for
object occlusion in a single camera and the grid-based approach for
extracting the accurate object feature. In addition, we considered the
appearance of people and the transition time between entry and exit
zones for tracking objects across blind regions of multiple cameras
with non-overlapping FOVs. The main contribution of this paper is to
estimate transition times between various entry and exit zones, and to
graphically represent the camera topology as an undirected weighted
graph using the transition probabilities.
Abstract: As mobile service's subscriber is increasing; mobile
contents services are getting more and more variables. So, mobile
contents development needs not only contents design but also
guideline for just mobile. And when mobile contents are developed, it
is important to pass the limit and restriction of the mobile. The
restrictions of mobile are small browser and screen size, limited
download size and uncomfortable navigation. So each contents of
mobile guideline will be presented for user's usability, easy of
development and consistency of rule. This paper will be proposed
methodology which is each contents of mobile guideline. Mobile web
will be developed by mobile guideline which I proposed.
Abstract: This paper presents the design and implements the prototype of an intelligent data processing framework in ubiquitous sensor networks. Much focus is put on how to handle the sensor data stream as well as the interoperability between the low-level sensor data and application clients. Our framework first addresses systematic middleware which mitigates the interaction between the application layer and low-level sensors, for the sake of analyzing a great volume of sensor data by filtering and integrating to create value-added context information. Then, an agent-based architecture is proposed for real-time data distribution to efficiently forward a specific event to the appropriate application registered in the directory service via the open interface. The prototype implementation demonstrates that our framework can host a sophisticated application on the ubiquitous sensor network and it can autonomously evolve to new middleware, taking advantages of promising technologies such as software agents, XML, cloud computing, and the like.
Abstract: Intelligent traffic surveillance technology is an issue in
the field of traffic data analysis. Therefore, we need the technology to
detect moving objects in real-time while there are variations in background and natural light. In this paper, we proposed a Weighted-Center Surround Difference
method for object detection in outdoor environments. The proposed system detects objects using the saliency map that is obtained by
analyzing the weight of each layers of Gaussian pyramid. In order to validate the effectiveness of our system, we implemented the proposed
method using a digital signal processor, TMS320DM6437.
Experimental results show that blurred noisy around objects was effectively eliminated and the object detection accuracy is improved.
Abstract: Academic research information service is a must for surveying previous studies in research and development process. OntoFrame is an academic research information service under Semantic Web framework different from simple keyword-based services such as CiteSeer and Google Scholar. The first purpose of this study is for revealing user behavior in their surveys, the objects of using academic research information services, and their needs. The second is for applying lessons learned from the results to OntoFrame.