Abstract: Numerical studies were conducted using Lattice
Boltzmann Method (LBM) to study the natural convection in a square
cavity in the presence of roughness. An algorithm based on a single
relaxation time Bhatnagar-Gross-Krook (BGK) model of Lattice
Boltzmann Method (LBM) was developed. Roughness was
introduced on both the hot and cold walls in the form of sinusoidal
roughness elements. The study was conducted for a Newtonian fluid
of Prandtl number (Pr) 1.0. The range of Ra number was explored
from 10^3 to 10^6 in a laminar region. Thermal and hydrodynamic
behavior of fluid was analyzed using a differentially heated square
cavity with roughness elements present on both the hot and cold wall.
Neumann boundary conditions were introduced on horizontal walls
with vertical walls as isothermal. The roughness elements were at the
same boundary condition as corresponding walls. Computational
algorithm was validated against previous benchmark studies
performed with different numerical methods, and a good agreement
was found to exist. Results indicate that the maximum reduction in
the average heat transfer was 16.66 percent at Ra number 10^5.
Abstract: Polycyclic aromatic hydrocarbons (PAHs) are formed
during the pyrolysis of scrap tyres to produce tyre pyrolytic oil
(TPO). Due to carcinogenic, mutagenic, and toxic properties PAHs
are priority pollutants. Hence it is essential to remove PAHs from
TPO before utilising TPO as a petroleum fuel alternative (to run the
engine). Agricultural wastes have promising future to be utilized as
biosorbent due to their cost effectiveness, abundant availability, high
biosorption capacity and renewability. Various low cost adsorbents
were prepared from natural sources. Uptake of PAHs present in tyre
pyrolytic oil was investigated using various low-cost adsorbents of
natural origin including sawdust (shisham), coconut fiber, neem bark,
chitin, activated charcoal. Adsorption experiments of different PAHs
viz. naphthalene, acenaphthalene, biphenyl and anthracene have been
carried out at ambient temperature (25°C) and at pH 7. It was
observed that for any given PAH, the adsorption capacity increases
with the lignin content. Freundlich constant Kf and 1/n have been
evaluated and it was found that the adsorption isotherms of PAHs
were in agreement with a Freundlich model, while the uptake
capacity of PAHs followed the order: activated charcoal> saw dust
(shisham) > coconut fiber > chitin. The partition coefficients in
acetone-water, and the adsorption constants at equilibrium, could be
linearly correlated with octanol–water partition coefficients. It is
observed that natural adsorbents are good alternative for PAHs
removal. Sawdust of Dalbergia sissoo, a by-product of sawmills was
found to be a promising adsorbent for the removal of PAHs present in
TPO. It is observed that adsorbents studied were comparable to those
of some conventional adsorbents.
Abstract: The present work aims to throw light on the effects of
arcing in air on the surface state of contact pastilles made of silvernickel
Ag-Ni (60/40). Also, the photoelectric emission from these
electrical contacts has been investigated in the spectral range of 196-
256 nm. In order to study the effects of arcing on the EWF, the
metallic samples were subjected to electrical arcs in air, at
atmospheric pressure and room temperature, after that, they have
been introduced into the vacuum chamber of an experimental UHV
set-up for EWF measurements. Both Fowler method of isothermal
curves and linearized Fowler plots were used for the measurement of
the EWF by the photoelectric effect.
It has been found that the EWF varies with the number of applied
arcs. Thus, after 500 arcs in air, the observed EWF increasing is
probably due to progressive inclusion of oxide on alloy surface.
Microscopic examination is necessary to get better understandings on
EWF of silver alloys, for both virgin and arced electrical contacts.
Abstract: The aim of this work was to apply extractive
distillation for acetonitrile removal from water solutions, to validate
thermodynamic criterion based on excess Gibbs energy to entrainer
selection process for acetonitrile – water mixture separation and show
its potential efficiency at isothermal conditions as well as at isobaric
(conditions of real distillation process), to simulate and analyze an
extractive distillation process with chosen entrainers: optimize
amount of trays and feeds, entrainer/original mixture and reflux
ratios. Equimolar composition of the feed stream was chosen for the
process, comparison of the energy consumptions was carried out.
Glycerol was suggested as the most energetically and ecologically
suitable entrainer.
Abstract: In this work, a polyaniline/Iron oxide (PANI/Fe2O3)
composite was chemically prepared by oxidative polymerization of
aniline in acid medium, in presence of ammonium persulphate as an
oxidant and amount of Fe2O3. The composite was characterized by a
scanning electron microscopy (SEM). The prepared composite has
been used as adsorbent to remove Tartrazine dye form aqueous
solutions.
The effects of initial dye concentration and temperature on the
adsorption capacity of PANI/Fe2O3 for Tartrazine dye have been
studied in this paper.
The Langmuir and Freundlich adsorption models have been used
for the mathematical description of adsorption equilibrium data. The
best fit is obtained using the Freundlich isotherm with an R2 value of
0.998. The change of Gibbs energy, enthalpy, and entropy of
adsorption has been also evaluated for the adsorption of Tartrazine
onto PANI/ Fe2O3. It has been proved according the results that the
adsorption process is endothermic in nature.
Abstract: Preparation of nanoparticles of cerium oxide and
adsorption of bovine serum albumin on them were studied. Particle
size distribution and influence of pH on zeta potential of prepared
CeO2 were determined. Average size of prepared cerium oxide
nanoparticles was 9 nm. The simultaneous measurements of the
bovine serum albumin adsorption and zeta potential determination of
the (adsorption) suspensions were carried out. The adsorption
isotherms were found to be of typical Langmuir type; values of the
bovine serum albumin adsorption capacities were calculated.
Increasing of pH led to decrease of zeta potential and decrease of
adsorption capacity of cerium oxide nanoparticles. The maximum
adsorption capacity was found for strongly acid suspension (am =
118 mg/g). The samples of nanoceria with positive zeta potential
adsorbed more bovine serum albumin on the other hand, the samples
with negative zeta potential showed little or no protein adsorption.
Surface charge or better say zeta potential of CeO2 nanoparticles
plays the key role in adsorption of proteins on such type of materials.
Abstract: Multiwall carbon nanotubes, prepared by chemical
vapor deposition, have an average diameter of 60-100 nm as shown
by High Resolution Transmittance Electron Microscope, HR-TEM.
The Multiwall carbon nanotubes (MWCNTs) were further
characterized using X-ray Diffraction and Raman Spectroscopy.
Mercury uptake capacity of MWCNTs was studied using batch
adsorption method at different concentration ranges up to 150 ppm.
Mercury concentration (before and after the treatment) was measured
using cold vapor atomic absorption spectroscopy. The effect of time,
concentration, pH and adsorbent dose were studied. MWCNT were
found to perform complete absorption in the sub-ppm concentrations
(parts per billion levels) while for high concentrations, the adsorption
efficiency was 92% at the optimum conditions; 0.1 g of the adsorbent
at 150 ppm mercury (II) solution. The adsorption of mercury on
MWCNTs was found to follow the Freundlich adsorption isotherm
and the pseudo-second order kinetic model.
Abstract: In this paper the effect of wall waviness of side walls
in a two-dimensional wavy enclosure is numerically investigated.
Two vertical wavy walls and straight top wall are kept isothermal and
the bottom wall temperature is higher and spatially varying with
cosinusoidal temperature distribution. A computational code based on
Finite-volume approach is used to solve governing equations and
SIMPLE method is used for pressure velocity coupling. Test is
performed for several different numbers of undulations. The Prandtl
number was kept constant and the Ra number denotes that the flow is
laminar. Temperature and velocity fields are determined. Therefore,
according to the obtained results a correlation is proposed for average
Nusselt number as a function of number of side wall waves. The
results indicate that the Nusselt number is highly affected by number
of waves and increasing it decreases the wavy walls Nusselt number;
although the Nusselt number is not highly affected by surface
waviness when the number of undulations is below one.
Abstract: This study was conducted to evaluate the manganese
removal from aqueous solution using Banana peels activated carbon
(BPAC). Batch experiments have been carried out to determine the
influence of parameters such as pH, biosorbent dose, initial metal ion
concentrations and contact times on the biosorption process. From
these investigations, a significant increase in percentage removal of
manganese 97.4% is observed at pH value 5.0, biosorbent dose 0.8 g,
initial concentration 20 ppm, temperature 25 ± 2°C, stirring rate 200
rpm and contact time 2h. The equilibrium concentration and the
adsorption capacity at equilibrium of the experimental results were
fitted to the Langmuir and Freundlich isotherm models; the Langmuir
isotherm was found to well represent the measured adsorption data
implying BPAC had heterogeneous surface. A raw groundwater
samples were collected from Baharmos groundwater treatment plant
network at Embaba and Manshiet Elkanater City/District-Giza,
Egypt, for treatment at the best conditions that reached at first phase
by BPAC. The treatment with BPAC could reduce iron and
manganese value of raw groundwater by 91.4% and 97.1%,
respectively and the effect of the treatment process on the
microbiological properties of groundwater sample showed decrease
of total bacterial count either at 22°C or at 37°C to 85.7% and 82.4%,
respectively. Also, BPAC was characterized using SEM and FTIR
spectroscopy.
Abstract: The mineral bioflotation represents a viable
alternative for the evaluation of new processes benefit alternative.
The adsorption bacteria on minerals surfaces will depend mainly on
the type of the microorganism as well as of the studied mineral
surface. In the current study, adhesion of S. carnosus on coal was
studied. Several methods were used as: DRX, Fourier Transform
Infra-Red (FTIR) adhesion isotherms and kinetic. The main goal is to
recovery of organic matter by the microflotation process on coal
particles with biological reagent (S. carnosus). Adhesion tests
revealed that adhesion took place after of 8 h at pH 9. The results
suggest that the adhesion of bacteria to solid substrates can be
considered an abiotic physicochemical process that is consequently
governed by bacterial surface properties such as their specific surface
area, hydrophobicity and surface functionalities. The greatest coal
fine flotability was of 75%, after 5 min of flotation.
Abstract: Three dimensional non-Interlaced carbon fibre
reinforced silicon carbide (3-D-Cf/SiC) composites with pyrocarbon
interphase were fabricated using isothermal chemical vapor
infiltration (ICVI) combined with polymer impregnation pyrolysis
(PIP) process. Polysilazane (PSZ) is used as a preceramic polymer to
obtain silicon carbide matrix. Thermo gravimetric analysis (TGA),
Infrared spectroscopic analysis (IR) and X-ray diffraction (XRD)
analysis were carried out on PSZ pyrolysed at different temperatures
to understand the pyrolysis and obtaining the optimum pyrolysing
condition to yield β-SiC phase. The density of the composites was
1.94 g cm-3 after the 3-D carbon preform was SiC infiltrated for 280 h
with one intermediate polysilazane pre-ceramic PIP process.
Mechanical properties of the composite materials were investigated
under tensile, flexural, shear and impact loading. The values of
tensile strength were 200 MPa at room temperature (RT) and 195
MPa at 500°C in air. The average RT flexural strength was 243 MPa.
The lower flexural strength of these composites is because of the
porosity. The fracture toughness obtained from single edge notched
beam (SENB) technique was 39 MPa.m1/2. The work of fracture
obtained from the load-displacement curve of SENB test was 22.8
kJ.m-2. The composites exhibited excellent impact resistance and the
dynamic fracture toughness of 44.8 kJ.m-2 is achieved as determined
from instrumented Charpy impact test. The shear strength of the
composite was 93 MPa, which is significantly higher compared 2-D
Cf/SiC composites. Microstructure evaluation of fracture surfaces
revealed the signatures of fracture processes and showed good
support for the higher toughness obtained.
Abstract: A new algorithm based on the lattice Boltzmann method (LBM) is proposed as a potential solver for one-dimensional heat and mass transfer for isothermal carbonization of wood particles. To check the validity of this algorithm, the LBM results have been compared with the published data and a good agreement is obtained. Then, the model is used to study the effect of reactor temperature and particle size on the evolution of the local temperature and mass loss inside the wood particle.
Abstract: In this paper, sodium borosilicates glasses were prepared by melting in air. These heat-resistant transparent glasses have subjected subsequently isothermal treatments at different times, which have transformed them at opaque glass (milky white color). Such changes indicate that these glasses showed clearly phase separation (immiscibility). The immiscibility region in a sodium borosilicate ternary system was investigated in this work, i.e. to determine the regions from which some compositions can show phase separation. For this we went through the conditions of thermodynamic equilibrium, which were translated later by mathematical equations to find an approximate solution. The latter has been translated in a simulation which was established thereafter to find the immiscibility regions in this type of special glasses.
Abstract: The process of thermoforming a carbon fiber reinforced thermoplastic (CFRTP) has increased its presence in the automotive industry for its wide applicability to the mass production car. A non-isothermal forming for CFRTP can shorten its cycle time to less than 1 minute. In this paper, the textile reinforcement FE model which the authors proposed in a previous work is extended to the CFRTP model for non-isothermal forming simulation. The effect of thermoplastic is given by adding shell elements which consider thermal effect to the textile reinforcement model. By applying Reuss model to the stress calculation of thermoplastic, the proposed model can accurately predict in-plane shear behavior, which is the key deformation mode during forming, in the range of the process temperature. Using the proposed model, thermoforming simulation was conducted and the results are in good agreement with the experimental results.
Abstract: This paper investigates the natural convection heat transfer performance in a complex-wavy-wall cavity filled with power-law fluid. In performing the simulations, the continuity, Cauchy momentum and energy equations are solved subject to the Boussinesq approximation using a finite volume method. The simulations focus specifically on the effects of the flow behavior index in the power-law model and the Rayleigh number on the flow streamlines, isothermal contours and mean Nusselt number within the cavity. The results show that pseudoplastic fluids have a better heat transfer performance than Newtonian or dilatant fluids. Moreover, it is shown that for Rayleigh numbers greater than Ra=103, the mean Nusselt number has a significantly increase as the flow behavior index is decreased.
Abstract: A numerical study based on the Lattice Boltzmann Method (LBM) is proposed to solve one, two and three dimensional heat and mass transfer for isothermal carbonization of thick wood particles. To check the validity of the proposed model, computational results have been compared with the published data and a good agreement is obtained. Then, the model is used to study the effect of reactor temperature and thermal boundary conditions, on the evolution of the local temperature and the mass distributions of the wood particle during carbonization
Abstract: The factors necessary to obtain an optimal heat treatment that influence the hardness and resistivity of Al-6Si-0.5Mg casting alloys with Cu or/and Ni additions were investigated. The alloys were homogenised (24hr at 500oC), solutionized (2hr at 540oC) and artificially ageing at various times and temperatures. The alloys were aged isochronally for 60 minutes at temperatures up to 400oC and isothermally at 150, 175, 200, 225, 250 & 300oC for different periods in the range 15 to 360 minutes. The hardness and electrical resistivity of the alloys were measured for various artificial ageing times and temperatures. From the isochronal ageing treatment, hardness found maximum ageing at 225oC. And from the isothermal ageing treatment, hardness found maximum for 60 minutes at 225oC. So the optimal heat treatment consists of 60 minutes ageing at 225oC.
Abstract: Alginite has been evaluated as an efficient pollution control material. In this paper, alginite from maar Pinciná (SR) for removal of Cd2+ ions from aqueous solution was studied. The potential sorbent was characterized by X-ray fluorescence analysis (RFA) analysis, Fourier transform infrared spectral analysis (FT-IR) and specific surface area (SSA) was also determined. The sorption process was optimized from the point of initial cadmium concentration effect and effect of pH value. The Freundlich and Langmuir models were used to interpret the sorption behavior of Cd2+ ions, and the results showed that experimental data were well fitted by the Langmuir equation. Alginite maximal sorption capacity (Qmax) for Cd2+ ions calculated from Langmuir isotherm was 34 mg/g. Sorption process was significantly affected by initial pH value in the range from 4.0-7.0. Alginite is a comparable sorbent with other materials for toxic metals removal.
Abstract: This paper is concerned with the effect of Hartmann number on the free convective flow in a square cavity with different positions of heated square block. The two-dimensional Physical and mathematical model have been developed, and mathematical model includes the system of governing mass, momentum and energy equations are solved by the finite element method. The calculations have been computed for Prandtl number Pr = 0.71, the Rayleigh number Ra = 1000 and the different values of Hartmann number. The results are illustrated with the streamlines, isotherms, velocity and temperature fields as well as local Nusselt number.
Abstract: Schiff base (E)-2-methyl-N-(tetrazolo[1,5-a]quinolin-4-ylmethylene)aniline (QMA) was synthesized, and its inhibitive effect for mild steel in 1N HCl solution was investigated by weight loss measurement and electrochemical tests. From the weight loss measurements and electrochemical tests, it was observed that the inhibition efficiency increases with the increase in the Schiff base concentration and reaches a maximum at the optimum concentration. This is further confirmed by the decrease in corrosion rate. It is found that the system follows Langmuir adsorption isotherm.