Abstract: Forward Osmosis (FO) polyamide thin-film composite
membranes have been prepared by interfacial polymerization using
commercial UF polyethersulfoneas membrane support. Different
interfacial polymerization times (10s, 30s and 60s) in the organic
solution containing trimesoyl chloride (TMC) at constant m-phenylenediamine
(MPD) concentration (2% w/v) were studied. The
synthesized polyamide membranes then tested for treatment of
natural organic matter (NOM) and compared to commercial Cellulose
TriAcetate (CTA) membrane. It was found that membrane prepared
with higher reaction time (30s and 60s) exhibited better membrane
performance (flux and humic acid removal) over commercial CTA
membrane.
Abstract: Experimental study of natural convection heat transfer
inside smooth and rough surfaces of vertical and inclined equilateral
triangular channels of different inclination angles with a uniformly
heated surface are performed. The inclination angle is changed from
15º to 90º. Smooth and rough surface of average roughness (0.02mm)
are used and their effect on the heat transfer characteristics are
studied. The local and average heat transfer coefficients and Nusselt
number are obtained for smooth and rough channels at different heat
flux values, different inclination angles and different Rayleigh
numbers (Ra) 6.48 × 105 ≤ Ra ≤ 4.78 × 106. The results show that
the local Nusselt number decreases with increase of axial distance
from the lower end of the triangular channel to a point near the upper
end of channel, and then, it slightly increases. Higher values of local
Nusselt number for rough channel along the axial distance compared
with the smooth channel. The average Nusselt number of rough
channel is higher than that of smooth channel by about 8.1% for
inclined case at θ = 45o and 10% for vertical case. The results
obtained are correlated using dimensionless groups for both rough
and smooth surfaces of the inclined and vertical triangular channels.
Abstract: An investigation into Cahn-Hilliard equation was
carried out through numerical simulation to identify a possible phase
separation for one and two dimensional domains. It was observed that
this equation can reproduce important mass fluxes necessary for
phase separation within the miscibility gap and for coalescence of
particles.
Abstract: The aim of this work was to apply extractive
distillation for acetonitrile removal from water solutions, to validate
thermodynamic criterion based on excess Gibbs energy to entrainer
selection process for acetonitrile – water mixture separation and show
its potential efficiency at isothermal conditions as well as at isobaric
(conditions of real distillation process), to simulate and analyze an
extractive distillation process with chosen entrainers: optimize
amount of trays and feeds, entrainer/original mixture and reflux
ratios. Equimolar composition of the feed stream was chosen for the
process, comparison of the energy consumptions was carried out.
Glycerol was suggested as the most energetically and ecologically
suitable entrainer.
Abstract: Alkylated silicon nanocrystals (C11-SiNCs) were
prepared successfully by galvanostatic etching of p-Si(100) wafers
followed by a thermal hydrosilation reaction of 1-undecene in
refluxing toluene in order to extract C11-SiNCs from porous silicon.
Erbium trichloride was added to alkylated SiNCs using a simple
mixing chemical route. To the best of our knowledge, this is the first
investigation on mixing SiNCs with erbium ions (III) by this
chemical method. The chemical characterization of C11-SiNCs and
their mixtures with Er3+(Er/C11-SiNCs) were carried out using X-ray
photoemission spectroscopy (XPS). The optical properties of C11-
SiNCs and their mixtures with Er3+ were investigated using Raman
spectroscopy and photoluminescence (PL). The erbium mixed
alkylated SiNCs shows an orange PL emission peak at around 595
nm that originates from radiative recombination of Si. Er/C11-SiNCs
mixture also exhibits a weak PL emission peak at 1536 nm that
originates from the intra-4f transition in erbium ions (Er3+). The PL
peak of Si in Er/C11-SiNCs mixture is increased in the intensity up to
three times as compared to pure C11-SiNCs. The collected data
suggest that this chemical mixing route leads instead to a transfer of
energy from erbium ions to alkylated SiNCs.
Abstract: Currently, thorium fuel has been especially noticed
because of its proliferation resistance than long half-life alpha emitter
minor actinides, breeding capability in fast and thermal neutron flux
and mono-isotopic naturally abundant. In recent years, efficiency of
minor actinide burning up in PWRs has been investigated. Hence, a
minor actinide-contained thorium based fuel matrix can confront both
proliferation resistance and nuclear waste depletion aims. In the
present work, minor actinide depletion rate in a CANDU-type nuclear
core modeled using MCNP code has been investigated. The obtained
effects of minor actinide load as mixture of thorium fuel matrix on
the core neutronics has been studied with comparing presence and
non-presence of minor actinide component in the fuel matrix.
Depletion rate of minor actinides in the MA-contained fuel has been
calculated using different power loads. According to the obtained
computational data, minor actinide loading in the modeled core
results in more negative reactivity coefficients. The MA-contained
fuel achieves less radial peaking factor in the modeled core. The
obtained computational results showed 140 kg of 464 kg initial load
of minor actinide has been depleted in during a 6-year burn up in 10
MW power.
Abstract: In this paper a novel design of aerostatic thrust bearing
is proposed and is analyzed numerically. The capillary restrictor and
bearing disk are made of elastomer like silicone and PU. The
viscoelasticity of elastomer helps the capillary expand for more air
flux and at the same time, allows conicity of the bearing surface to
form when the air pressure is enhanced. Therefore the bearing has the
better ability of passive compensation. In the present example, as
compared with the typical model, the new designs can nearly double
the load capability and offer four times static stiffness.
Abstract: This paper reports the numerical and experimental
performances of Double Glass Wall are investigated. Two
configurations were considered namely, the Double Clear Glass Wall
(DCGW) and the Double Translucent Glass Wall (DTGW). The
coupled governing equations as well as boundary conditions are
solved using the finite element method (FEM) via COMSOLTM
Multiphysics. Temperature profiles and flow field of the DCGW and
DTGW are reported and discussed. Different constant heat fluxes
were considered as 400 and 800 W.m-2 the corresponding initial
condition temperatures were 30.5 and 38.5ºC respectively. The
results show that the simulation results are in agreement with the
experimental data. Conclusively, the model considered in this study
could reasonable be used simulate the thermal and ventilation
performance of the DCGW and DTGW configurations.
Abstract: In this research article a comprehensive investigation
has been carried out to determine the effect of thermal cycle on
temperature dependent process parameters developed during gas
tungsten arc (GTA) welding of high carbon (AISI 1090) steel butt
joints. An experiment based thermal analysis has been performed to
obtain the thermal history. We have focused on different
thermophysical properties such as thermal conductivity, heat transfer
coefficient and cooling rate. Angular torch model has been utilized to
find out the surface heat flux and its variation along the fusion zone as
well as along the longitudinal direction from fusion boundary. After
welding and formation of weld pool, heat transfer coefficient varies
rapidly in the vicinity of molten weld bead and heat affected zone. To
evaluate the heat transfer coefficient near the fusion line and near the
rear end of the plate (low temperature region), established correlation
has been implemented and has been compared with empirical
correlation which is noted as coupled convective and radiation heat
transfer coefficient. Change in thermal conductivity has been
visualized by analytical model of moving point heat source. Rate of
cooling has been estimated by using 2-dimensional mathematical
expression of cooling rate and it has shown good agreement with
experimental temperature cycle. Thermophysical properties have been
varied randomly within 0 -10s time span.
Abstract: This study presents the numerical simulation of three-dimensional incompressible steady and laminar fluid flow and conjugate heat transfer of a trapezoidal microchannel heat sink using water as a cooling fluid in a silicon substrate. Navier-Stokes equations with conjugate energy equation are discretized by finite-volume method. We perform numerical computations for a range of 50 ≦ Re ≦ 600, 0.05W ≦ P ≦ 0.8W, 20W/cm2 ≦q"≦ 40W/cm2. The present study demonstrates the numerical optimization of a trapezoidal microchannel heat sink design using the response surface methodology (RSM) and the genetic algorithm method (GA). The results show that the average Nusselt number increases with an increase in the Reynolds number or pumping power, and the thermal resistance decreases as the pumping power increases. The thermal resistance of a trapezoidal microchannel is minimized for a constant heat flux and constant pumping power.
Abstract: The aim of this work is to analyze a viscous flow
around the axisymmetric blunt body taken into account the mesh size
both in the free stream and into the boundary layer. The resolution of
the Navier-Stokes equations is realized by using the finite volume
method to determine the flow parameters and detached shock
position. The numerical technique uses the Flux Vector Splitting
method of Van Leer. Here, adequate time stepping parameter, CFL
coefficient and mesh size level are selected to ensure numerical
convergence. The effect of the mesh size is significant on the shear
stress and velocity profile. The best solution is obtained with using a
very fine grid. This study enabled us to confirm that the
determination of boundary layer thickness can be obtained only if the
size of the mesh is lower than a certain value limits given by our
calculations.
Abstract: A 3D-conjugate numerical investigation was conducted to predict heat transfer characteristics in a rectangular cross-sectional micro-channel employing simultaneously developing Tow-phase flows. The sole purpose for analyzing two phase flow heat transfer in rectangular micro channel is to pin point what are the different factors affecting this phenomenon. Different methods and techniques have been undertaken to analyze the equations arising constituting the flow of heat from gas phase to liquid phase and vice versa.Different models of micro channels have been identified and analyzed. How the geometry of micro channels affects their activity i.e. of circular and non-circular geometry has also been reviewed. To the study the results average Nusselt no plotted against the Reynolds no has been taken into consideration to study average heat exchange in micro channels against applied heat flux. High heat fluxes up to 140 W/cm2 were applied to investigate micro-channel thermal characteristics.
Abstract: The optimization of biological systems, which is a branch of metabolic engineering, has generated a lot of industrial and academic interest for a long time. In the last decade, metabolic engineering approaches based on mathematical optimizations have been used extensively for the analysis and manipulation of metabolic networks. In practical optimization of metabolic reaction networks, designers have to manage the nature of uncertainty resulting from qualitative characters of metabolic reactions, e.g., the possibility of enzyme effects. A deterministic approach does not give an adequate representation for metabolic reaction networks with uncertain characters. Fuzzy optimization formulations can be applied to cope with this problem. A fuzzy multi-objective optimization problem can be introduced for finding the optimal engineering interventions on metabolic network systems considering the resilience phenomenon and cell viability constraints. The accuracy of optimization results depends heavily on the development of essential kinetic models of metabolic networks. Kinetic models can quantitatively capture the experimentally observed regulation data of metabolic systems and are often used to find the optimal manipulation of external inputs. To address the issues of optimizing the regulatory structure of metabolic networks, it is necessary to consider qualitative effects, e.g., the resilience phenomena and cell viability constraints. Combining the qualitative and quantitative descriptions for metabolic networks makes it possible to design a viable strain and accurately predict the maximum possible flux rates of desired products. Considering the resilience phenomena in metabolic networks can improve the predictions of gene intervention and maximum synthesis rates in metabolic engineering. Two case studies will present in the conference to illustrate the phenomena.
Abstract: The ice rink floor is the largest heat exchanger in an ice rink. The important part of the floor consists of concrete, and the thermophysical properties of this concrete have strong influence on the energy usage of the ice rink. The thermal conductivity of concrete can be increased by using iron ore as ballast. In this study, the Transient Plane Source (TPS) method showed an increase up to 58.2% of thermal conductivity comparing the improved concrete to standard concrete. Moreover, two alternative ice rink floor designs are suggested to incorporate the improved concrete. A 2D simulation was developed to investigate the temperature distribution in the conventional and the suggested designs. The results show that the suggested designs reduce the temperature difference between the ice surface and the brine by 1-4˚C, when comparing with convectional designs at equal heat flux. This primarily leads to an increased coefficient of performance (COP) in the primary refrigeration cycle and secondly to a decrease in the secondary refrigerant pumping power. The suggested designs have great potential to reduce the energy usage of ice rinks. Depending on the load scenario in the ice rink, the saving potential lies in the range of 3-10% of the refrigeration system energy usage. This calculation is based on steady state conditions and the potential with improved dynamic behavior is expected to increase the potential saving.
Abstract: Instantaneous electromagnetic torque of simple reflectance generator can be positive at a time and negative at other time. It is utilized to design a permanent magnet reluctance generator specifically. Generator is designed by combining two simple reluctance generators, consists of two rotors mounted on the same shaft, two output-windings and a field source of the permanent magnet. By this design, the electromagnetic torque on both rotor will be eliminated each other, so the input torque generator can be smaller. Rotor is expected only to regulate the flux flow to both output windings alternately, until the magnetic energy is converted into electrical energy, such as occurs in the transformer energy conversion. The prototype trials have been made to test this design. The test result show that the new design of permanent magnets reluctance generator able to convert energy from permanent magnets into electrical energy, this is proven by the existence 167% power output compared to the shaft input power.
Abstract: This paper presents a study on the effect of
second-order slip on forced convection through a long isoflux heated
or cooled planar microchannel. The fully developed solutions of flow
and thermal fields are analytically obtained on the basis of the
second-order Maxwell-Burnett slip and local heat flux boundary
conditions. Results reveal that when the average flow velocity
increases or the wall heat flux amount decreases, the role of thermal
creep becomes more insignificant, while the effect of second-order slip
becomes larger. The second-order term in the Deissler slip boundary
condition is found to contribute a positive velocity slip and then to lead
to a lower pressure drop as well as a lower temperature rise for the
heated-wall case or to a higher temperature rise for the cooled-wall
case. These findings are contrary to predictions made by the
Karniadakis slip model.
Abstract: There is a great advancement towards the All-Electric Aircraft (AEA) technology. The AEA concept assumes that all aircraft systems will be integrated into one electrical power source in the future. The principle of the electro-thermal system is to transfer the energy required for anti/de-icing to the protected areas in electrical form. However, powering a large aircraft anti-icing system electrically could be quite excessive in cost and system weight. Hence, maximising the anti/de-icing efficiency of the electro-thermal system in order to minimise its power demand has become crucial to electro-thermal de-icing system sizing. In this work, an enhanced methodology has been developed for conceptual sizing of aircraft electro-thermal de-icing System. The work factored those critical terms overlooked in previous studies which were critical to de-icing energy consumption. A case study of a typical large aircraft wing de-icing was used to test and validate the model. The model was used to optimise the system performance by a trade-off between the de-icing peak power and system energy consumption. The optimum melting surface temperatures and energy flux predicted enabled the reduction in the power required for de-icing. The weight penalty associated with electro-thermal anti-icing/de-icing method could be eliminated using this method without under estimating the de-icing power requirement.
Abstract: In the era of sustainability, utilization of livestock wastes as soil amendment to provide micronutrients for crops is very economical and sustainable. It is well understood that livestock wastes are comparable, if not better, nutrient sources for crops as chemical fertilizers. However, the large concentrated volumes of animal manure produced from livestock operations and the limited amount of available nearby agricultural land areas necessitated the need for volume reduction of these animal wastes. Composting of these animal manures is a viable option for biomass and pathogenic reduction in the environment. Nevertheless, composting also increases the potential loss of available nutrients for crop production as well as unwanted emission of anthropogenic air pollutants due to the loss of ammonia and other compounds via volatilization. In this study, we examine the emission of ammonia and nitrous oxide from swine manure windrows to evaluate the benefit of biomass reduction in conjunction with the potential loss of available nutrients. The feedstock for the windrows was obtained from swine farm in Kentucky where swine manure was mixed with wood shaving as absorbent material. Static flux chambers along with photoacoustic gas analyzer were used to monitor ammonia and nitrous oxide concentrations during the composting process. The results show that ammonia and nitrous oxide fluxes were quite high during the initial composting process and after the turning of each compost pile. Over the period of roughly three months of composting, the biochemical oxygen demand (BOD) decreased by about 90%. Although composting of animal waste is quite beneficial for biomass reduction, composting may not be economically feasible from an agronomical point of view due to time, nutrient loss (N loss), and potential environmental pollution (ammonia and greenhouse gas emissions). Therefore, additional studies are needed to assess and validate the economics and environmental impact of animal (swine) manure composting (e.g., crop yield or impact on climate change).
Abstract: The cellulose was extracted from pomelo peel and an
etherification reaction used for converting cellulose to carboxymethyl
cellulose (CMC). The pomelo peel was refluxed with 0.5 M HCl and 1
M NaOH solution at 90°C for 1 h and 2 h, respectively. The cellulose
was bleached with calcium hypochlorite and used as precursor. The
precursor was soaked in mixed solution between isopropyl alcohol and
40%w/v NaOH for 12 h. After that, chloroacetic acid was added and
reacted at 55°C for 6 h. The optimum condition was 5 g of cellulose:
0.25 mole of NaOH : 0.07 mole of ClCH2COOH with 78.00% of yield.
Moreover, the product had 0.54 of degree of substitution (DS).
Abstract: A mathematical heat transfer model for the prediction of transient heating of the slab in a direct-fired walking beam type reheating furnace has been developed by considering the nongray thermal radiation with given furnace environments. The furnace is modeled as radiating nongray medium with carbon dioxide and water with five-zoned gas temperature and the furnace wall is considered as a constant temperature lower than furnace gas one. The slabs are moving with constant velocity depending on the residence time through the non-firing, charging, preheating, heating, and final soaking zones. Radiative heat flux obtained by considering the radiative heat exchange inside the furnace as well as convective one from the surrounding hot gases are introduced as boundary condition of the transient heat conduction within the slab. After validating thermal radiation model adopted in this work, thermal fields in both model and real reheating furnace are investigated in terms of radiative heat flux in the furnace and temperature inside the slab. The results show that the slab in the furnace can be more heated with higher slab emissivity and residence time.