Abstract: In the present study, feasibility of the selective surface
hydrophilization of polyvinyl chloride (PVC) by microwave treatment
was evaluated to facilitate the separation from automotive shredder
residue (ASR), by the froth flotation. The combination of 60 sec
microwave treatment with PAC, a sharp and significant decrease about
16.5° contact angle of PVC was observed in ASR plastic compared
with other plastics. The microwave treatment with the addition of PAC
resulted in a synergetic effect for the froth flotation, which may be a
result of the 90% selective separation of PVC from ASR plastics, with
82% purity. While, simple mixing with a nanometallic Ca/CaO/PO4
dispersion mixture immobilized 95-100% of heavy metals in ASR
soil/residues. The quantity of heavy metals leached from thermal
residues after treatment by nanometallic Ca/CaO/PO4 was lower than
the Korean standard regulatory limit for hazardous waste landfills.
Microwave treatment can be a simple and effective method for PVC
separation from ASR plastics.
Abstract: Thermoacoustic refrigerator is a cooling device which
uses the acoustic waves to produce the cooling effect. The aim of this
paper is to explore the experimental and numerical feasibility of a
standing-wave thermoacoustic refrigerator. The effects of the stack
length, position of stack and operating frequency on the cooling
performance are carried out. The circular pore stacks are tested under
the atmospheric pressure. A low-cost loudspeaker is used as an
acoustic driver. The results show that the location of stack installed in
resonator tube has a greater effect on the cooling performance, than
the stack length and operating frequency, respectively. The
temperature difference across the ends of stack can be generated up
to 13.7°C, and the temperature of cold-end is dropped down by 5.3°C
from the ambient temperature.
Abstract: The power electronic components within Electric Vehicles (EV) need to operate in several important modes. Some modes directly influence safety, while others influence vehicle performance. Given the variety of functions and operational modes required of the power electronics, it needs to meet efficiency requirements to minimize power losses. Another challenge in the control and construction of such systems is the ability to support bidirectional power flow. This paper considers the construction, operation, and feasibility of available converters for electric vehicles with feasible configurations of electrical buses and loads. This paper describes logic and control signals for the converters for different operations conditions based on the efficiency and energy usage bases.
Abstract: Diets high in processed foods have been found to lack
essential micro-nutrients for optimum human development and
overall health. Some micro-nutrients such as copper (Cu) have been
found to enhance the inflammatory response through its oxidative
functions, thereby having a role in cardiovascular disease, metabolic
syndrome, diabetes and related complications. This research study
was designed to determine if food crops could be bio-fortified with
micro-nutrients by growing sprouts on mineral fortified fiber mats. In
the feasibility study described in this contribution, recycled cellulose
fibers and clay, saturated with either micro-nutrient copper ions or
copper nanoparticles, were converted to a novel mineral-cellulose
fiber carrier of essential micro-nutrient and of antimicrobial
properties. Seeds of Medicago sativa (alfalfa), purchased from a
commercial, organic supplier were germinated on engineered
cellulose fiber mats. After the appearance of the first leaves, the
sprouts were dehydrated and analyzed for Cu content. Nutrient
analysis showed ~2 increase in Cu of the sprouts grown on the fiber
mats with copper particles, and ~4 increase on mats with ionic copper
as compared to the control samples. This study illustrates the
potential for the use of engineered mats as a viable way to increase
the micro-nutrient composition of locally-grown food crops and the
need for additional research to determine the uptake, nutritional
implications and risks of micro-nutrient bio-fortification.
Abstract: The effects of the contact ball-lens on the soda lime
glass in laser thermal cleavage with a cw Nd-YAG laser were
investigated in this study. A contact ball-lens was adopted to generate
a bending force on the crack formation of the soda-lime glass in the
laser cutting process. The Nd-YAG laser beam (wavelength of 1064
nm) was focused through the ball-lens and transmitted to the soda-lime
glass, which was coated with a carbon film on the surface with a
bending force from a ball-lens to generate a tensile stress state on the
surface cracking. The fracture was controlled by the contact ball-lens
and a straight cutting was tested to demonstrate the feasibility.
Experimental observations on the crack propagation from the leading
edge, main section and trailing edge of the glass sheet were compared
with various mechanical and thermal loadings. Further analyses on the
stress under various laser powers and contact ball loadings were made
to characterize the innovative technology. The results show that the distributions of the side crack at the
leading and trailing edges are mainly dependent on the boundary
condition, contact force, cutting speed and laser power. With the
increase of the mechanical and thermal loadings, the region of the side
cracks might be dramatically reduced with proper selection of the
geometrical constrains. Therefore the application of the contact
ball-lens is a possible way to control the fracture in laser cleavage with
improved cutting qualities.
Abstract: Foundation differential settlement and supported
structure tilting are an occasionally occurred engineering problem.
This may be caused by overloading, changes in ground soil properties
or unsupported nearby excavations. Engineering thinking points
directly toward the logic solution for such problem by uplifting the
settled side. This can be achieved with deep foundation elements
such as micro-piles and macro-piles™, jacked piers, and helical piers,
jet grouted mortar columns, compaction grout columns, cement
grouting or with chemical grouting, or traditional pit underpinning
with concrete and mortar. Although, some of these techniques offer
economic, fast and low noise solutions, many of them are quite the
contrary. For tilted structures, with the limited inclination, it may be much
easier to cause a balancing settlement on the less-settlement side
which shall be done carefully in a proper rate. This principal has been
applied in Leaning Tower of Pisa stabilization with soil extraction
from the ground surface. In this research, the authors attempt to
introduce a new solution with a different point of view. So, the
micro-tunneling technique is presented in here as an intended ground
deformation cause. In general, micro-tunneling is expected to induce
limited ground deformations. Thus, the researchers propose to apply
the technique to form small size ground unsupported holes to produce
the target deformations. This shall be done in four phases: 1.
Application of one or more micro-tunnels, regarding the existing
differential settlement value, under the raised side of the tilted
structure. 2. For each individual tunnel, the lining shall be pulled out
from both sides (from jacking and receiving shafts) in the slow rate.
3. If required, according to calculations and site records, an additional
surface load can be applied on the raised foundation side. 4. Finally, a
strengthening soil grouting shall be applied for stabilization after
adjustment. A finite element based numerical model is presented to simulate
the proposed construction phases for different tunneling positions and
tunnels group. For each case, the surface settlements are calculated
and induced plasticity points are checked. These results show the
impact of the suggested procedure on the tilted structure and its
feasibility. Comparing results also show the importance of the
position selection and tunnels group gradual effect. Thus, a new
engineering solution is presented to one of the structural and
geotechnical engineering challenges.
Abstract: Ocean current is always available around the
surrounding of SHELL Sabah Water Platform and data are collected
every 10 minutes, 24 hours a day, for a period of 365 days. Due to
low current speed, conventional hydrokinetic power generation is not
feasible, thus leading to the study of low current enabled vortex
induced vibration power generation application. In this case, the
design of a vortex induced vibration application is studied to obtain
an optimum design for the VIV oscillator. Power output is then
determined to study the feasibility of the VIV application in low
current condition.
Abstract: There are a number of Distributed Generations (DGs)
installed in microgrid, which may have diverse path and direction of
power flow or fault current. The overcurrent protection scheme for the
traditional radial type distribution system will no longer meet the
needs of microgrid protection. Integrating the Intelligent Electronic
Device (IED) and a Supervisory Control and Data Acquisition
(SCADA) with IEC 61850 communication protocol, the paper
proposes a Microgrid Protection Management System (MPMS) to
protect power system from the fault. In the proposed method, the
MPMS performs logic programming of each IED to coordinate their
tripping sequence. The GOOSE message defined in IEC 61850 is used
as the transmission information medium among IEDs. Moreover, to
cope with the difference in fault current of microgrid between
grid-connected mode and islanded mode, the proposed MPMS applies
the group setting feature of IED to protect system and robust
adaptability. Once the microgrid topology varies, the MPMS will
recalculate the fault current and update the group setting of IED.
Provided there is a fault, IEDs will isolate the fault at once. Finally, the
Matlab/Simulink and Elipse Power Studio software are used to
simulate and demonstrate the feasibility of the proposed method.
Abstract: As a by-product of the biodiesel industries, glycerol
has been vastly generated which surpasses the market demand. It is
imperative to develop an efficient glycerol valorization processes in
minimizing the net energy requirement and intensifying the biodiesel
production. In this study, base-catalyzed transesterification of
glycerol with dimethyl carbonate using microwave irradiation as
heating method to produce glycerol carbonate was conducted by
varying grades of glycerol, i.e. 70%, 86% and 99% purity, that is
obtained from biodiesel plant. Metal oxide catalysts were used with
varying operating parameters including reaction time, DMC/glycerol
molar ratio, catalyst weight %, temperature and stirring speed. From
the study on the effect of different operating parameters it was found
that the type of catalyst used has the most significant effect on the
transesterification reaction. Amidst the metal oxide catalysts
examined, CaO gave the best performance. This study indicates the
feasibility of producing glycerol carbonate using different grade of
glycerol in both conventional thermal activation and microwave
irradiation with CaO as catalyst. Microwave assisted
transesterification (MAT) of glycerol into glycerol carbonate has
demonstrated itself as an energy efficient route by achieving 94.2%
yield of GC at 65°C, 5 minutes reaction time, 1 wt% CaO and
DMC/glycerol molar ratio of 2. The advantages of MAT
transesterification route has made the direct utilization of bioglycerol
from biodiesel production without the need of purification. This has
marked a more economical and less-energy intensive glycerol
carbonate synthesis route.
Abstract: Anammox is a novel and promising technology that has changed the traditional concept of biological nitrogen removal. The process facilitates direct oxidation of ammonical nitrogen under anaerobic conditions with nitrite as an electron acceptor without addition of external carbon sources. The present study investigated the feasibility of Anammox Hybrid Reactor (AHR) combining the dual advantages of suspended and attached growth media for biodegradation of ammonical nitrogen in wastewater. Experimental unit consisted of 4 nos. of 5L capacity AHR inoculated with mixed seed culture containing anoxic and activated sludge (1:1). The process was established by feeding the reactors with synthetic wastewater containing NH4-H and NO2-N in the ratio 1:1 at HRT (hydraulic retention time) of 1 day. The reactors were gradually acclimated to higher ammonium concentration till it attained pseudo steady state removal at a total nitrogen concentration of 1200 mg/l. During this period, the performance of the AHR was monitored at twelve different HRTs varying from 0.25-3.0 d with increasing NLR from 0.4 to 4.8 kg N/m3d. AHR demonstrated significantly higher nitrogen removal (95.1%) at optimal HRT of 1 day. Filter media in AHR contributed an additional 27.2% ammonium removal in addition to 72% reduction in the sludge washout rate. This may be attributed to the functional mechanism of filter media which acts as a mechanical sieve and reduces the sludge washout rate many folds. This enhances the biomass retention capacity of the reactor by 25%, which is the key parameter for successful operation of high rate bioreactors. The effluent nitrate concentration, which is one of the bottlenecks of anammox process was also minimised significantly (42.3-52.3 mg/L). Process kinetics was evaluated using first order and Grau-second order models. The first-order substrate removal rate constant was found as 13.0 d-1. Model validation revealed that Grau second order model was more precise and predicted effluent nitrogen concentration with least error (1.84±10%). A new mathematical model based on mass balance was developed to predict N2 gas in AHR. The mass balance model derived from total nitrogen dictated significantly higher correlation (R2=0.986) and predicted N2 gas with least error of precision (0.12±8.49%). SEM study of biomass indicated the presence of heterogeneous population of cocci and rod shaped bacteria of average diameter varying from 1.2-1.5 mm. Owing to enhanced NRE coupled with meagre production of effluent nitrate and its ability to retain high biomass, AHR proved to be the most competitive reactor configuration for dealing with nitrogen laden wastewater.
Abstract: Determination of genetic variation is useful for plant
breeding and hence production of more efficient plant species under
different conditions, like drought stress. In this study a sample of 28
recombinant inbred lines (RILs) of wheat developed from the cross of
Norstar and Zagross varieties, together with their parents, were
evaluated for two years (2010-2012) under normal and water stress
conditions using split plot design with three replications. Main plots
included two irrigation treatments of 70 and 140 mm evaporation
from Class A pan and sub-plots consisted of 30 genotypes. The effect
of genotypes and interaction of genotypes with years and water
regimes were significant for all characters. Significant genotypic
effect implies the existence of genetic variation among the lines
under study. Heritability estimates were high for 1000 grain weight
(0.87). Biomass and grain yield showed the lowest heritability values
(0.42 and 0.50, respectively). Highest genotypic and phenotypic
coefficients of variation (GCV and PCV) belonged to harvest index.
Moderate genetic advance for most of the traits suggested the
feasibility of selection among the RILs under investigation. Some
RILs were higher yielding than either parent at both environments.
Abstract: Biodiesel production from vegetable oil will produce
glycerol as by-product about 10% of the biodiesel production. The
amount of glycerol that was produced needed alternative way to
handling immediately so as to not become the waste that polluted
environment. One of the solutions was to process glycerol to
polyglycidyl nitrate (PGN). PGN is synthesized from glycerol by
three-step reactions i.e. nitration of glycerol, cyclization of 13-
dinitroglycerine and polymerization of glycosyl nitrate. Optimum
condition of nitration of glycerol with nitric acid has not been known.
Thermodynamic feasibility should be done before run experiments in
the laboratory. The aim of this study was to determine the parameters
those affect nitration of glycerol and nitric acid and chose the
operation condition. Many parameters were simulated to verify its
possibility to experiment under conditions which would get the
highest conversion of 1, 3-dinitroglycerine and which was the ideal
condition to get it. The parameters that need to be studied to obtain
the highest conversion of 1, 3-dinitroglycerine were mol ratio of
nitric acid/glycerol, reaction temperature, mol ratio of
glycerol/dichloromethane and pressure. The highest conversion was
obtained in the range of mol ratio of nitric acid /glycerol between 2/1
– 5/1, reaction temperature of 5-25oC and pressure of 1 atm. The
parameters that need to be studied further to obtain the highest
conversion of 1.3 DNG are mol ratio of nitric acid/glycerol and
reaction temperature.
Abstract: This paper aims to project the construction of a
prototype azimuthal thruster, mounted with materials of low cost and
easy access, testing in a controlled environment to measure their
performance, characteristics and feasibility of future projects. The
construction of the simulation of dynamic positioning software,
responsible for simulating a vessel and reposition it when necessary.
Validation tests were performed in the form of partial or complete
system. These tests validate the system manually or automatically.
The system provides an interface to the user and simulates the
conditions unfavorable positioning of a vessel, accurately calculates
the azimuth angle, the direction of rotation of the helix and the time
that this should be turned on so that the vessel back to position
original. A serial communication connects the Simulation Dynamic
Positioning System with Embedded System causing the usergenerated
data to simulate the DP system arrives in the form of
control signals to the motors of the propellant. This article addresses
issues in the marine industry employees.
Abstract: The using of waste materials in the construction
industry can reduce the dependence on the natural aggregates which
are going at the end to deplete. The glass waste is generated in a huge
amount which can make one of its disposals in concrete industry
effective not only as a green solution but also as an advantage to
enhance the performance of mechanical properties and durability of
concrete. This article reports the performance of concrete specimens
containing different percentages of milled glass waste as a partial
replacement of cement (Powder), when they are subject to cycles of
freezing and thawing. The tests were conducted on 75-mm cubes and
75 x 75 x 300-mm prisms. Compressive strength based on laboratory
testing and non-destructive ultrasonic pulse velocity test were
performed during the action of freezing-thawing cycles (F/T). The
results revealed that the incorporation of glass waste in concrete
mixtures is not only feasible but also showed generally better strength
and durability performance than control concrete mixture. It may be
said that the recycling of waste glass in concrete mixes is not only a
disposal way, but also it can be an exploitation in concrete industry.
Abstract: An Acoustic Micro-Energy Harvester (AMEH) is
developed to convert wasted acoustical energy into useful electrical
energy. AMEH is mathematically modeled using Lumped Element
Modelling (LEM) and Euler-Bernoulli beam (EBB) modelling. An
experiment is designed to validate the mathematical model and assess
the feasibility of AMEH. Comparison of theoretical and experimental
data on critical parameter value such as Mm, Cms, dm and Ceb showed
the variances are within 1% to 6%, which is reasonably acceptable.
Then, AMEH undergoes bandwidth tuning for performance
optimization. The AMEH successfully produces 0.9V/(m/s^2) and
1.79μW/(m^2/s^4) at 60Hz and 400kΩ resistive load which only
show variances about 7% compared to theoretical data. At 1g and
60Hz resonance frequency, the averaged power output is about
2.2mW which fulfilled a range of wireless sensors and
communication peripherals power requirements. Finally, the design
for AMEH is assessed, validated and deemed as a feasible design.
Abstract: In this study, the feasibility of incorporating ceramic
waste from bricks (perforated brick and double hollow brick) and
extruded polystyrene (XPS) waste, is analysed.
Results show that it is possible to incorporate up to 25% of
ceramic waste and 4% of XPS waste over the weight of gypsum in a
gypsum matrix. Furthermore, with the addition of ceramic waste an
8% of surface hardness increase and a 25% of capillary water
absorption reduction can be obtained. On the other hand, with the
addition of XPS, a 26% reduction of density and a 37% improvement
of thermal conductivity can be obtained.
The obtained results are favorable to use these materials in order to
produce prefabricated gypsum and also as material for interior
cladding walls.
Abstract: This study examines the feasibility of indirect solar
desalination in oil producing countries in the Middle East and North
Africa (MENA) region. It relies on value engineering (VE) and costbenefit
with sensitivity analyses to identify optimal coupling
configurations of desalination and solar energy technologies. A
comparative return on investment was assessed as a function of water
costs for varied plant capacities (25,000 to 75,000 m3/day), project
lifetimes (15 to 25 years), and discount rates (5 to 15%) taking into
consideration water and energy subsidies, land cost as well as
environmental externalities in the form of carbon credit related to
greenhouse gas (GHG) emissions reduction. The results showed
reverse osmosis (RO) coupled with photovoltaic technologies (PVs)
as the most promising configuration, robust across different prices for
Brent oil, discount rates, as well as different project lifetimes.
Environmental externalities and subsidies analysis revealed that a
16% reduction in existing subsidy on water tariffs would ensure
economic viability. Additionally, while land costs affect investment
attractiveness, the viability of RO coupled with PV remains possible
for a land purchase cost
Abstract: Cerebellar ataxia is a steadily progressive
neurodegenerative disease associated with loss of motor control,
leaving patients unable to walk, talk, or perform activities of daily
living. Direct motor instruction in cerebella ataxia patients has limited
effectiveness, presumably because an inappropriate closed-loop
cerebellar response to the inevitable observed error confounds motor
learning mechanisms. Could the use of EEG based BCI provide
advanced biofeedback to improve motor imagery and provide a
“backdoor” to improving motor performance in ataxia patients? In
order to determine the feasibility of using EEG-based BCI control in
this population, we compare the ability to modulate mu-band power
(8-12 Hz) by performing a cued motor imagery task in an ataxia
patient and healthy control.
Abstract: Transportation of long turbine blades from one place
to another is a difficult process. Hence a feasibility study of
modularization of wind turbine blade was taken from structural
standpoint through finite element analysis. Initially, a non-segmented
blade is modeled and its structural behavior is evaluated to serve as
reference. The resonant, static bending and fatigue tests are simulated
in accordance with IEC61400-23 standard for comparison purpose.
The non-segmented test blade is separated at suitable location based
on trade off studies and the segments are joined with an innovative
double strap bonded joint configuration. The adhesive joint is
modeled by adopting cohesive zone modeling approach in ANSYS.
The developed blade model is analyzed for its structural response
through simulation. Performances of both the blades are found to be
similar, which indicates that, efficient segmentation of the long blade
is possible which facilitates easy transportation of the blades and on
site reassembling. The location selected for segmentation and
adopted joint configuration has resulted in an efficient segmented
blade model which proves the methodology adopted for segmentation
was quite effective. The developed segmented blade appears to be the
viable alternative considering its structural response specifically in
fatigue within considered assumptions.
Abstract: A new steganographic method via the use of numeric
data on public websites with a self-authentication capability is
proposed. The proposed technique transforms a secret message into
partial shares by Shamir’s (k, n)-threshold secret sharing scheme with
n = k + 1. The generated k+1 partial shares then are embedded into the
numeric items to be disguised as part of the website’s numeric content,
yielding the stego numeric content. Afterward, a receiver links to the
website and extracts every k shares among the k+1 ones from the stego
numeric content to compute k+1 copies of the secret, and the
phenomenon of value consistency of the computed k+1 copies is taken
as an evidence to determine whether the extracted message is authentic
or not, attaining the goal of self-authentication of the extracted secret
message. Experimental results and discussions are provided to show
the feasibility and effectiveness of the proposed method.