Abstract: There is a acute water problem especially in the dry
season in and around Perundurai (Erode district, Tamil Nadu, India)
where there are more number of tannery units. Hence an attempt was
made to use the waste water from tannery industry for construction
purpose. The mechanical properties such as compressive strength,
tensile strength, flexural strength etc were studied by casting various
concrete specimens in form of cube, cylinders and beams etc and
were found to be satisfactory. Hence some special properties such as
chloride attack, sulphate attack and chemical attack are considered
and comparatively studied with the conventional potable water. In
this experimental study the results of specimens prepared by using
treated and untreated tannery effluent were compared with the
concrete specimens prepared by using potable water. It was observed
that the concrete had some reduction in strength while subjected to
chloride attack, sulphate attack and chemical attack. So admixtures
were selected and optimized in suitable proportion to counter act the
adverse effects and the results were found to be satisfactory.
Abstract: Rice husk is one of the alternative fuels for Thailand because of its high potential and environmental benefits. Nonetheless, the environmental profile of the electricity production from rice husk must be assessed to ensure reduced environmental damage. A 10 MW pilot plant using rice husk as feedstock is the study site. The environmental impacts from rice husk power plant are evaluated by using the Life Cycle Assessment (LCA) methodology. Energy, material and carbon balances have been determined for tracing the system flow. Carbon closure has been used for describing of the net amount of CO2 released from the system in relation to the amount being recycled between the power plant and the CO2 adsorbed by rice husk. The transportation of rice husk to the power plant has significant on global warming, but not on acidification and photo-oxidant formation. The results showed that the impact potentials from rice husk power plant are lesser than the conventional plants for most of the categories considered; except the photo-oxidant formation potential from CO. The high CO from rice husk power plant may be due to low boiler efficiency and high moisture content in rice husk. The performance of the study site can be enhanced by improving the combustion efficiency.
Abstract: This paper presents a technical speaker adaptation
method called WMLLR, which is based on maximum likelihood linear
regression (MLLR). In MLLR, a linear regression-based transform
which adapted the HMM mean vectors was calculated to maximize the
likelihood of adaptation data. In this paper, the prior knowledge of the
initial model is adequately incorporated into the adaptation. A series of
speaker adaptation experiments are carried out at a 30 famous city
names database to investigate the efficiency of the proposed method.
Experimental results show that the WMLLR method outperforms the
conventional MLLR method, especially when only few utterances
from a new speaker are available for adaptation.
Abstract: In this paper electrical characteristics of various kinds
of multiple-gate silicon nanowire transistors (SNWT) with the
channel length equal to 7 nm are compared. A fully ballistic quantum
mechanical transport approach based on NEGF was employed to
analyses electrical characteristics of rectangular and cylindrical
silicon nanowire transistors as well as a Double gate MOS FET. A
double gate, triple gate, and gate all around nano wires were studied
to investigate the impact of increasing the number of gates on the
control of the short channel effect which is important in nanoscale
devices. Also in the case of triple gate rectangular SNWT inserting
extra gates on the bottom of device can improve the application of
device. The results indicate that by using gate all around structures
short channel effects such as DIBL, subthreshold swing and delay
reduces.
Abstract: Fructooligosaccharides derived from microbial enzyme especially from fungal sources has been received particular attention due to its beneficial effects as prebiotics and mass production. However, fungal fermentation is always cumbersome due to its broth rheology problem that will eventually affect the production of FOS. This study investigated the efficiency of immobilized cell system using rotating fibrous bed bioreactor (RFBB) in producing fructooligosaccharides (FOS). A comparative picture with respect to conventional stirred tank bioreactor (CSTB) and RFBB has been presented. To demonstrate the effect of agitation intensity and aeration rate, a laboratory-scale bioreactor 2.5 L was operated in three phases (high, medium, low) for 48 hours. Agitation speed has a great influence on P. simplicissimum fermentation for FOS production, where the volumetric FOS productivity using RFBB is increased with almost 4 fold compared to the FOS productivity in CSTB that only 0.319 g/L/h. Rate of FOS production increased up to 1.2 fold when immobilized cells system was employed at aeration rate similar to the freely suspended cells at 2.0 vvm.
Abstract: This paper suggests an improved integer frequency
offset (IFO) estimation scheme using P1 symbol for orthogonal
frequency division multiplexing (OFDM) based the second generation
terrestrial digital video broadcasting (DVB-T2) system. Proposed
IFO estimator is designed by a low-complexity blind IFO estimation
scheme, which is implemented with complex additions. Also, we
propose active carriers (ACs) selection scheme in order to prevent
performance degradation in blind IFO estimation. The simulation
results show that under the AWGN and TU6 channels, the proposed
method has low complexity than conventional method and almost
similar performance in comparison with the conventional method.
Abstract: This paper proposes a fast code acquisition scheme for
optical code division multiple access (O-CDMA) systems. Unlike the
conventional scheme, the proposed scheme employs multiple thresholds
providing a shorter mean acquisition time (MAT) performance.
The simulation results show that the MAT of the proposed scheme
is shorter than that of the conventional scheme.
Abstract: It is known that if harmonic spectra are decreased, then
acoustic noise also decreased. Hence, this paper deals with a new
random switching strategy using DSP TMS320F2812 to decrease the
harmonics spectra of single phase switched reluctance motor. The
proposed method which combines random turn-on, turn-off angle
technique and random pulse width modulation technique is shown. A
harmonic spread factor (HSF) is used to evaluate the random
modulation scheme. In order to confirm the effectiveness of the new
method, the experimental results show that the harmonic intensity of
output voltage for the proposed method is better than that for
conventional methods.
Abstract: This paper presents a novel two-phase hybrid optimization algorithm with hybrid genetic operators to solve the optimal control problem of a single stage hybrid manufacturing system. The proposed hybrid real coded genetic algorithm (HRCGA) is developed in such a way that a simple real coded GA acts as a base level search, which makes a quick decision to direct the search towards the optimal region, and a local search method is next employed to do fine tuning. The hybrid genetic operators involved in the proposed algorithm improve both the quality of the solution and convergence speed. The phase–1 uses conventional real coded genetic algorithm (RCGA), while optimisation by direct search and systematic reduction of the size of search region is employed in the phase – 2. A typical numerical example of an optimal control problem with the number of jobs varying from 10 to 50 is included to illustrate the efficacy of the proposed algorithm. Several statistical analyses are done to compare the validity of the proposed algorithm with the conventional RCGA and PSO techniques. Hypothesis t – test and analysis of variance (ANOVA) test are also carried out to validate the effectiveness of the proposed algorithm. The results clearly demonstrate that the proposed algorithm not only improves the quality but also is more efficient in converging to the optimal value faster. They can outperform the conventional real coded GA (RCGA) and the efficient particle swarm optimisation (PSO) algorithm in quality of the optimal solution and also in terms of convergence to the actual optimum value.
Abstract: In this article, we propose an Intelligent Medical
Diagnostic System (IMDS) accessible through common
web-based interface, to on-line perform initial screening for
osteoporosis. The fundamental approaches which construct the
proposed system are mainly based on the fuzzy-neural theory,
which can exhibit superiority over other conventional technologies
in many fields. In diagnosis process, users simply answer
a series of directed questions to the system, and then they
will immediately receive a list of results which represents the
risk degrees of osteoporosis. According to clinical testing results,
it is shown that the proposed system can provide the general
public or even health care providers with a convenient, reliable,
inexpensive approach to osteoporosis risk assessment.
Abstract: Decentralized eco-sanitation system is a promising and sustainable mode comparing to the century-old centralized conventional sanitation system. The decentralized concept relies on an environmentally and economically sound management of water, nutrient and energy fluxes. Source-separation systems for urban waste management collect different solid waste and wastewater streams separately to facilitate the recovery of valuable resources from wastewater (energy, nutrients). A resource recovery centre constituted for 20,000 people will act as the functional unit for the treatment of urban waste of a high-density population community, like Singapore. The decentralized system includes urine treatment, faeces and food waste co-digestion, and horticultural waste and organic fraction of municipal solid waste treatment in composting plants. A design model is developed to estimate the input and output in terms of materials and energy. The inputs of urine (yellow water, YW) and faeces (brown water, BW) are calculated by considering the daily mean production of urine and faeces by humans and the water consumption of no-mix vacuum toilet (0.2 and 1 L flushing water for urine and faeces, respectively). The food waste (FW) production is estimated to be 150 g wet weight/person/day. The YW is collected and discharged by gravity into tank. It was found that two days are required for urine hydrolysis and struvite precipitation. The maximum nitrogen (N) and phosphorus (P) recovery are 150-266 kg/day and 20-70 kg/day, respectively. In contrast, BW and FW are mixed for co-digestion in a thermophilic acidification tank and later a decentralized/centralized methanogenic reactor is used for biogas production. It is determined that 6.16-15.67 m3/h methane is produced which is equivalent to 0.07-0.19 kWh/ca/day. The digestion residues are treated with horticultural waste and organic fraction of municipal waste in co-composting plants.
Abstract: This paper investigates and compares performance of
various conventional and fuzzy logic based controllers at generator
locations for oscillation damping. Performance of combination of
conventional and fuzzy logic based controllers also studied by
comparing overshoot on the active power deviation response for a
small disturbance and damping ratio of the critical mode. Fuzzy logic
based controllers can not be modeled in the state space form to get
the eigenvalues and corresponding damping ratios of various modes
of generators and controllers. Hence, a new method based on tracing
envelop of time domain waveform is also presented and used in the
paper for comparing performance of controllers. The paper also
shows that if the fuzzy based controllers designed separately
combining them could not lead to a better performance.
Abstract: The stochastic nature of tool life using conventional discrete-wear data from experimental tests usually exists due to many individual and interacting parameters. It is a common practice in batch production to continually use the same tool to machine different parts, using disparate machining parameters. In such an environment, the optimal points at which tools have to be changed, while achieving minimum production cost and maximum production rate within the surface roughness specifications, have not been adequately studied. In the current study, two relevant aspects are investigated using coated and uncoated inserts in turning operations: (i) the accuracy of using machinability information, from fixed parameters testing procedures, when variable parameters situations are emerged, and (ii) the credibility of tool life machinability data from prior discrete testing procedures in a non-stop machining. A novel technique is proposed and verified to normalize the conventional fixed parameters machinability data to suit the cases when parameters have to be changed for the same tool. Also, an experimental investigation has been established to evaluate the error in the tool life assessment when machinability from discrete testing procedures is employed in uninterrupted practical machining.
Abstract: DS-CDMA system is well known wireless
technology. This system suffers from MAI (Multiple Access
Interference) caused by Direct Sequence users. Multi-User Detection
schemes were introduced to detect the users- data in presence of
MAI. This paper focuses on linear multi-user detection schemes used
for data demodulation. Simulation results depict the performance of
three detectors viz-conventional detector, Decorrelating detector and
Subspace MMSE (Minimum Mean Square Error) detector. It is seen
that the performance of these detectors depends on the number of
paths and the length of Gold code used.
Abstract: The use of artificial neural network (ANN) modeling
for prediction and forecasting variables in water resources
engineering are being increasing rapidly. Infrastructural applications
of ANN in terms of selection of inputs, architecture of networks,
training algorithms, and selection of training parameters in different
types of neural networks used in water resources engineering have
been reported. ANN modeling conducted for water resources
engineering variables (river sediment and discharge) published in
high impact journals since 2002 to 2011 have been examined and
presented in this review. ANN is a vigorous technique to develop
immense relationship between the input and output variables, and
able to extract complex behavior between the water resources
variables such as river sediment and discharge. It can produce robust
prediction results for many of the water resources engineering
problems by appropriate learning from a set of examples. It is
important to have a good understanding of the input and output
variables from a statistical analysis of the data before network
modeling, which can facilitate to design an efficient network. An
appropriate training based ANN model is able to adopt the physical
understanding between the variables and may generate more effective
results than conventional prediction techniques.
Abstract: This paper presents a fast and efficient on-line technique for estimating impedance of unbalanced loads in power systems. The proposed technique is an application of a discrete timedynamic filter based on stochastic estimation theory which is suitable for estimating parameters in noisy environment. The algorithm uses sets of digital samples of the distorted voltage and current waveforms of the non-linear load to estimate the harmonic contents of these two signal. The non-linear load impedance is then calculated from these contents. The method is tested using practical data. Results are reported and compared with those obtained using the conventional least error squares technique. In addition to the very accurate results obtained, the method can detect and reject bad measurements. This can be considered as a very important advantage over the conventional static estimation methods such as the least error square method.
Abstract: The Integrated Performance Modelling Environment
(IPME) is a powerful simulation engine for task simulation and
performance analysis. However, it has no high level cognition such
as memory and reasoning for complex simulation. This article
introduces a knowledge representation and reasoning scheme that can
accommodate uncertainty in simulations of military personnel with
IPME. This approach demonstrates how advanced reasoning models
that support similarity-based associative process, rule-based abstract
process, multiple reasoning methods and real-time interaction can be
integrated with conventional task network modelling to provide
greater functionality and flexibility when modelling operator
performance.
Abstract: In this paper, the application of GRNN in
modeling of SOFC fuel cells were studied. The parameters
are of interested as voltage and power value and the current
changes are investigated. In addition, the comparison between
GRNN neural network application and conventional method
was made. The error value showed the superlative results.
Abstract: A novel typical day prediction model have been built and validated by the measured data of a grid-connected solar photovoltaic (PV) system in Macau. Unlike conventional statistical method used by previous study on PV systems which get results by averaging nearby continuous points, the present typical day statistical method obtain the value at every minute in a typical day by averaging discontinuous points at the same minute in different days. This typical day statistical method based on discontinuous point averaging makes it possible for us to obtain the Gaussian shape dynamical distributions for solar irradiance and output power in a yearly or monthly typical day. Based on the yearly typical day statistical analysis results, the maximum possible accumulated output energy in a year with on site climate conditions and the corresponding optimal PV system running time are obtained. Periodic Gaussian shape prediction models for solar irradiance, output energy and system energy efficiency have been built and their coefficients have been determined based on the yearly, maximum and minimum monthly typical day Gaussian distribution parameters, which are obtained from iterations for minimum Root Mean Squared Deviation (RMSD). With the present model, the dynamical effects due to time difference in a day are kept and the day to day uncertainty due to weather changing are smoothed but still included. The periodic Gaussian shape correlations for solar irradiance, output power and system energy efficiency have been compared favorably with data of the PV system in Macau and proved to be an improvement than previous models.
Abstract: In modern distributed software systems, the issue of communication among composing parts represents a critical point, but the idea of extending conventional programming languages with general purpose communication constructs seems difficult to realize. As a consequence, there is a (growing) gap between the abstraction level required by distributed applications and the concepts provided by platforms that enable communication. This work intends to discuss how the Model Driven Software Development approach can be considered as a mature technology to generate in automatic way the schematic part of applications related to communication, by providing at the same time high level specialized languages useful in all the phases of software production. To achieve the goal, a stack of languages (meta-meta¬models) has been introduced in order to describe – at different levels of abstraction – the collaborative behavior of generic entities in terms of communication actions related to a taxonomy of messages. Finally, the generation of platforms for communication is viewed as a form of specification of language semantics, that provides executable models of applications together with model-checking supports and effective runtime environments.