Abstract: In the present paper the displacement-based nonconforming quadrilateral affine thin plate bending finite element ARPQ4 is presented, derived directly from non-conforming quadrilateral thin plate bending finite element RPQ4 proposed by Wanji and Cheung [19]. It is found, however, that element RPQ4 is only conditionally unisolvent. The new element is shown to be inherently unisolvent. This convenient property results in the element ARPQ4 being more robust and thus better suited for computations than its predecessor. The convergence is proved and the rate of convergence estimated. The mathematically rigorous proof of convergence presented in the paper is based on Stummel-s generalized patch test and the consideration of the element approximability condition, which are both necessary and sufficient for convergence.
Abstract: In this paper, the effects of the restoring force device on the response of a space frame structure resting on sliding type of bearing with a restoring force device is studied. The NS component of the El - Centro earthquake and harmonic ground acceleration is considered for earthquake excitation. The structure is modeled by considering six-degrees of freedom (three translations and three rotations) at each node. The sliding support is modeled as a fictitious spring with two horizontal degrees of freedom. The response quantities considered for the study are the top floor acceleration, base shear, bending moment and base displacement. It is concluded from the study that the displacement of the structure reduces by the use of the restoring force device. Also, the peak values of acceleration, bending moment and base shear also decreases. The simulation results show the effectiveness of the developed and proposed method.
Abstract: Nowadays the construction industry is growing specially among developing counties. Iran also has a critical role in these industries in terms of workers disorders. Work-related musculoskeletal disorders (WMSDs) assign 7% of the whole diseases in the society, which make some limitations. One of the main factors, which are ended to WMSDs, is awkward posture. Steel bar bending is considered as one of the prominent performance among construction workers. In this case study we conducted to find the major tasks of bar benders and the most important related risk factors. This study was carried out among twenty workers (18-45 years) as our volunteer samples in some construction sites with less than 6 floors in two regions of Tehran municipality. The data was gathered through in depth observation, interview and questionnaire. Also postural analysis was done by OWAS. In another part of study we used NMQ for gathering some data about psychosocial effects of work related disorders. Our findings show that 64% of workers were not aware of work risks, also about 59% of workers had troubles in their wrists, hands, and especially among workers who worked in steel bar bending. In 46% cases low back pain were prevalence. Considering with gathered data and results, awkward postures and long term tasks and its duration are known as the main risk factors in WMSDs among construction workers, so work-rest schedule and also tools design should be considered to make an ergonomic condition for the mentioned workers.
Abstract: In this paper, an analytical approach is used to study the coupled lateral-torsional vibrations of laminated composite beam. It is known that in such structures due to the fibers orientation in various layers, any lateral displacement will produce a twisting moment. This phenomenon is modeled by the bending-twisting material coupling rigidity and its main feature is the coupling of lateral and torsional vibrations. In addition to the material coupling, the effects of shear deformation and rotary inertia are taken into account in the definition of the potential and kinetic energies. Then, the governing differential equations are derived using the Hamilton-s principle and the mathematical model matches the Timoshenko beam model when neglecting the effect of bending-twisting rigidity. The equations of motion which form a system of three coupled PDEs are solved analytically to study the free vibrations of the beam in lateral and rotational modes due to the bending, as well as the torsional mode caused by twisting. The analytic solution is carried out in three steps: 1) assuming synchronous motion for the kinematic variables which are the lateral, rotational and torsional displacements, 2) solving the ensuing eigenvalue problem which contains three coupled second order ODEs and 3) imposing different boundary conditions related to combinations of simply, clamped and free end conditions. The resulting natural frequencies and mode shapes are compared with similar results in the literature and good agreement is achieved.
Abstract: In order to supplement the brittle property of concrete,
fibers are added into concrete mixtures. Compared to general concrete,
various characteristics such as tensile strength, bending strength,
bending toughness, and resistance to crack are superior, and even
when cracks occur, improvements on toughness as well as resistance
to shock are excellent due to the growth of fracture energy. Increased
function of steel fiber reinforced concrete can be differentiated
depending on the fiber dispersion, and sand percentage can be an
important influence on the fiber dispersion. Therefore, in this research,
experiments were planned on sand percentage in order to apprehend
the influence of sand percentage on the bending properties and direct
tension of SFRC and basic experiments were conducted on bending
and direct tension in order to recognize the properties of bending
properties and direct tension following the size of the aggregates and
sand percentage.
Abstract: In this note, a theoretical model for analyzing of
normal penetration of the ogive – nose projectile into metallic targets
is presented .The failure is assumed to be asymmetry petalling and
the analysis is performed by using the energy balance and work done
.The work done consist of the work required for plastic deformation
Wp, the work for transferring the matter to new position Wd and the
work for bending of the petals Wb. In several studies, it has been
shown that we can neglect the loss of energy by temperature.
In this present study, in first, by assuming the crater formation
after perforation, the value of work done is calculated during the
normal penetration of conical projectiles into thin metallic targets.
Then the value of residual velocity and ballistic limit of the projectile
is predicated by using the energy balance. In final, theoretical and
experimental results is compared.
Abstract: Transpedicular screw fixation in spinal fractures,
degenerative changes, or deformities is a well-established procedure.
However, important rate of fixation failure due to screw bending,
loosening, or pullout are still reported particularly in weak bone stock
in osteoporosis. To overcome the problem, mechanism of failure has
to be fully investigated in vitro. Post-mortem human subjects are less
accessible and animal cadavers comprise limitations due to different
geometry and mechanical properties. Therefore, the development of a
synthetic model mimicking the realistic human vertebra is highly
demanded. A bone surrogate, composed of Polyurethane (PU) foam
analogous to cancellous bone porous structure, was tested for 3
different densities in this study. The mechanical properties were
investigated under uniaxial compression test by minimizing the end
artifacts on specimens. The results indicated that PU foam of 0.32
g.cm-3 density has comparable mechanical properties to human
cancellous bone in terms of young-s modulus and yield strength.
Therefore, the obtained information can be considered as primary
step for developing a realistic cancellous bone of human vertebral
body. Further evaluations are also recommended for other density
groups.
Abstract: To achieve accurate and precise results of finite
element analysis (FEA) of bones, it is important to represent the
load/boundary conditions as identical as possible to the human body
such as the bone properties, the type and force of the muscles, the
contact force of the joints, and the location of the muscle attachment.
In this study, the difference in the Von-Mises stress and the total
deformation was compared by classifying them into Case 1, which
shows the actual anatomical form of the muscle attached to the femur
when the same muscle force was applied, and Case 2, which gives a
simplified representation of the attached location. An inverse
dynamical musculoskeletal model was simulated using data from an
actual walking experiment to complement the accuracy of the
muscular force, the input value of FEA. The FEA method using the
results of the muscular force that were calculated through the
simulation showed that the maximum Von-Mises stress and the
maximum total deformation in Case 2 were underestimated by 8.42%
and 6.29%, respectively, compared to Case 1. The torsion energy and
bending moment at each location of the femur occurred via the stress
ingredient. Due to the geometrical/morphological feature of the femur
of having a long bone shape when the stress distribution is wide, as
shown in Case 1, a greater Von-Mises stress and total deformation are
expected from the sum of the stress ingredients. More accurate results
can be achieved only when the muscular strength and the attachment
location in the FEA of the bones and the attachment form are the same
as those in the actual anatomical condition under the various moving
conditions of the human body.
Abstract: Without uncertainty by applying external loads on
beams, bending is created. The created bending in I-beams, puts one
of the flanges in tension and the other one in compression. With increasing of bending, compression flange buckled and beam in out
of its plane direction twisted, this twisting well-known as Lateral Torsional Buckling. Providing bending moment varieties along the
beam, the critical moment is greater than the case its under pure bending. In other words, the value of bending gradient coefficient is
always greater than unite. In this article by the use of " ANSYS 10.0" software near 80 3-D finite element models developed for the
propose of analyzing beams` lateral torsional buckling and surveying influence of slenderness on beams' bending gradient coefficient.
Results show that, presented Cb coefficient via AISC is not correct for some of beams and value of this coefficient is smaller than what proposed by AISC. Therefore instead of using a constant Cb for each
case of loading , a function with two criterion for calculation of Cb coefficient for some cases is proposed.
Abstract: Porcelain specimens were fired at 6C/min to 1250C (dwell time 0.5-3h) and cooled at 6C/min to room temperature. Additionally, three different slower firing/cooling cycles were tried. Sintering profile and effects on MOR, crystalline phase content and morphology were investigated using dilatometry, 4-point bending strength, XRD and FEG-SEM respectively. Industrial-sized specimens prepared using the promising cycle were tested basing on the ANSI standards. Increasing dwell time from 1h to 3h at peak temperature of 1250C resulted in neither a significant effect on the quartz and mullite content nor MOR. Reducing the firing/cooling rate to below 6C/min, for peak temperature of 1250C (dwell time of 1h) does not result in improvement of strength of porcelain. The industrial sized specimen exhibited flashover voltages of 20.3kV (dry) and 9.3kV (wet) respectively, transverse strength of 12.5kN and bulk density of 2.27g/cm3, which are satisfactory. There was however dye penetration during porosity test. KeywordsDwell time, Microstructure, Porcelain, Strength.
Abstract: Composite steel-concrete slabs using thin-walled
corrugated steel sheets with embossments represent a modern and
effective combination of steel and concrete. However, the design
of new types of sheeting is conditional on the execution of expensive
and time-consuming laboratory testing. The effort to develop
a cheaper and faster method has lead to many investigations all over
the world. In our paper we compare the results from our experiments
involving vacuum loading, four-point bending and small-scale shear
tests.
Abstract: Real-time measurement of applied forces, like tension, compression, torsion, and bending moment, identifies the transferred energies being applied to the bottomhole assembly (BHA). These forces are highly detrimental to measurement/logging-while-drilling tools and downhole equipment. Real-time measurement of the dynamic downhole behavior, including weight, torque, bending on bit, and vibration, establishes a real-time feedback loop between the downhole drilling system and drilling team at the surface. This paper describes the numerical analysis of the strain data acquired by the measurement tool at different locations on the strain pockets. The strain values obtained by FEA for various loading conditions (tension, compression, torque, and bending moment) are compared against experimental results obtained from an identical experimental setup. Numerical analyses results agree with experimental data within 8% and, therefore, substantiate and validate the FEA model. This FEA model can be used to analyze the combined loading conditions that reflect the actual drilling environment.
Abstract: The purpose of this study is to design a portable virtual
piano. By utilizing optical fiber gloves and the virtual piano software
designed by this study, the user can play the piano anywhere at any
time. This virtual piano consists of three major parts: finger tapping
identification, hand movement and positioning identification, and
MIDI software sound effect simulation. To play the virtual piano, the
user wears optical fiber gloves and simulates piano key tapping
motions. The finger bending information detected by the optical fiber
gloves can tell when piano key tapping motions are made. Images
captured by a video camera are analyzed, hand locations and moving
directions are positioned, and the corresponding scales are found. The
system integrates finger tapping identification with information about
hand placement in relation to corresponding piano key positions, and
generates MIDI piano sound effects based on this data. This
experiment shows that the proposed method achieves an accuracy rate
of 95% for determining when a piano key is tapped.
Abstract: The work presents a development of EN338 strength classes for Strombosia pustulata, Pterygotama crocarpa, Nauclea diderrichii and Entandrophragma cyclindricum Nigerian timber species. The specimens for experimental measurements were obtained from the timber-shed at the famous Panteka market in Kaduna in the northern part of Nigeria. Laboratory experiments were conducted to determine the physical and mechanical properties of the selected timber species in accordance with EN 13183-1 and ASTM D193. The mechanical properties were determined using three point bending test. The generated properties were used to obtain the characteristic values of the material properties in accordance with EN384. The selected timber species were then classified according to EN 338. Strombosia pustulata, Pterygotama crocarpa, Nauclea diderrichii and Entandrophragma cyclindricum were assigned to strength classes D40, C14, D40 and D24 respectively. Other properties such as tensile and compressive strengths parallel and perpendicular to grains, shear strength as well as shear modulus were obtained in accordance with EN 338.
Abstract: In a metal forming process, the friction between the
material and the tools influences the process by modifying the stress
distribution of the workpiece. This frictional behaviour is often taken
into account by using a constant coefficient of friction in the finite
element simulations of sheet metal forming processes. However,
friction coefficient varies in time and space with many parameters.
The Stribeck friction model is investigated in this study to predict
springback behaviour of AA6061-T4 sheets during V-bending
process. The coefficient of friction in Stribeck curve depends on
sliding velocity and contact pressure. The plane-strain bending
process is simulated in ABAQUS/Standard. We compared the
computed punch load-stroke curves and springback related to the
constant coefficient of friction with the defined friction model. The
results clearly showed that the new friction model provides better
agreement between experiments and results of numerical simulations.
The influence of friction models on stress distribution in the
workpiece is also studied numerically
Abstract: Pressure vessels are usually operating at temperatures
where the conditions of linear elastic fracture mechanics are no
longer met because massive plasticity precedes crack propagation. In
this work the development of a surface crack in a pressure vessel
subject to bending and tension under elastic-plastic fracture
mechanics conditions was investigated. Finite element analysis was
used to evaluate the hydrostatic stress, the J-integral and crack
growth for semi-elliptical surface-breaking cracks. The results
showed non-uniform stress triaxiality and crack driving force around
the crack front at large deformation levels. Different ductile crack
extensions were observed which emphasis the dependent of ductile
tearing on crack geometry and type of loading. In bending the crack
grew only beneath the surface, and growth was suppressed at the
deepest segment. This contrasts to tension where the crack breaks
through the thickness with uniform growth along the entire crack
front except at the free surface. Current investigations showed that
the crack growth developed under linear elastic fracture mechanics
conditions will no longer be applicable under ductile tearing
scenarios.
Abstract: Low carbon deep drawing steel DC 01 according to EN 10130-91 was nitrooxidized in dissociated ammonia at 580°C/45 min and consequently oxidised at 380°C/5 min in vapour of distilled water. Material after nitrooxidation had 54 % increase of yield point, 34 % increase of strength and 10-times increased resistance to atmospheric corrosion in comparison to the material before nitrooxidation. The microstructure of treated material consisted of thin ε-phase layer connected to layer containing precipitated massive needle shaped Fe4N - γ' nitrides. This layer passed to a diffusion layer consisting of fine irregular shaped Fe16N2 - α'' nitrides regularly dispersed in ferritic matrix. Fatigue properties were examined under bending load with frequency of 20 kHz and sinusoidal symmetric cycle. The results confirmed positive influence of nitrooxidation on fatigue properties as fatigue limit of treated material was double in comparison to untreated material.
Abstract: In this paper the strength of adhesive joint under
tension and bending is discussed on the basis of intensity of
singular stress by the application of FEM. A useful method is
presented with focusing on the stress at the edge of interface
between the adhesive and adherent obtained by FEM. After
analyzing the adhesive joint strength with all material
combinations, it is found that to improve the interface strength,
thin adhesive layers are desirable because the intensity of
singular stress decreases with decreasing the thickness.
Abstract: CTMA-bentonite and BTEA-Bentonite prepared by Na-bentonite cation exchanged with cetyltrimethylammonium(CTMA) and benzyltriethylammonium (BTEA). Products were characterized by XRD and IR techniques.The d001 spacing value of CTMA-bentonite and BTEA-bentonite are 7.54Å and 3.50Å larger than that of Na-bentonite at 100% cation exchange capacity, respectively. The IR spectrum showed that the intensities of OH stretching and bending vibrations of the two organoclays decreased greatly comparing to untreated Na-bentonite. Batch experiments were carried out at 303 K, 318 K and 333 K to obtain the sorption isotherms of Crystal violet onto the two organoclays. The results show that the sorption isothermal data could be well described by Freundlich model. The dynamical data for the two organoclays fit well with pseudo-second-order kinetic model. The adsorption capacity of CTMA-bentonite was found higher than that of BTEA-Bentonite. Thermodynamic parameters such as changes in the free energy (ΔG°), the enthalpy (ΔH°) and the entropy (ΔS°) were also evaluated. The overall adsorption process of Crystal violet onto the two organoclays were spontaneous, endothermic physisorption. The CTMA-bentonite and BTEA-Bentonite could be employed as low-cost alternatives to activated carbon in wastewater treatment for the removal of color which comes from textile dyes.
Abstract: The paper deals with calculation of the parameters of
ceramic material from a set of destruction tests of ceramic heads of
total hip joint endoprosthesis. The standard way of calculation of the
material parameters consists in carrying out a set of 3 or 4 point
bending tests of specimens cut out from parts of the ceramic material
to be analysed. In case of ceramic heads, it is not possible to cut out
specimens of required dimensions because the heads are too small (if
the cut out specimens were smaller than the normalised ones, the
material parameters derived from them would exhibit higher strength
values than those which the given ceramic material really has). On
that score, a special testing jig was made, in which 40 heads were
destructed. From the measured values of circumferential strains of the
head-s external spherical surface under destruction, the state of stress
in the head under destruction was established using the final elements
method (FEM). From the values obtained, the sought for parameters
of the ceramic material were calculated using Weibull-s weakest-link
theory.