Abstract: Polyurethanes (PURs) are very versatile polymeric
materials with a wide range of physical and chemical properties.
PURs have desirable properties such as high abrasion resistance, tear
strength, shock absorption, flexibility and elasticity. Although they
have relatively poor thermal stability, this can be improved by using
treated clay. Polyurethane/clay nanocomposites have been
synthesized from renewable sources. A polyol for the production of
polyurethane by reaction with an isocyanate was obtained by the
synthesis of palm oil-based oleic acid with glycerol. Dodecylbenzene
sulfonic acid (DBSA) was used as catalyst and emulsifier. The
unmodified clay (kunipia-F) was treated with cetyltrimethyl
ammonium bromide (CTAB-mont) and octadodecylamine (ODAmont).
The d-spacing in CTAB-mont and ODA-mont were 1.571 nm
and 1.798 nm respectively and larger than that of the pure-mont
(1.142 nm). The organoclay was completely intercalated in the
polyurethane, as confirmed by a wide angle x-ray diffraction
(WAXD) pattern.
The results showed that adding clay demonstrated better thermal
stability in comparison with the virgin polyurethane. Onset
degradation of pure PU is at 200oC, and is lower than that of the
CTAB-mont PU and ODA-mont PU which takes place at about
318oC and 330oC, respectively. The mechanical properties (including
the dynamic mechanical properties) of pure polyurethane (PU) and
PU/clay nanocomposites, were measured. The modified organoclay
had a remarkably beneficial effect on the strength and elongation at
break of the nanocomposites, which both increased with increasing
clay content with the increase of the tensile strength of more than
214% and 267% by the addition of only 5 wt% of the
montmorillonite CTAB-mont PU and ODA-mont PU, respectively.
Abstract: The accomplished study is based on the appointment
and identification of ageing effects and according to this absorption
of moisture of aircraft cabin components over the life-cycle. In the
first step of the study ceiling panels from same age and from the
same aircraft cabin have been examined according to weight changes
depending on the position in the aircraft cabin. In the second step of
the study different aged ceiling panels have been examined
concerning deflection, weight changes and the acoustic sound
transmission loss. To prove the assumption of water absorption
within the study and with the theoretical background from literature
and scientific papers, an older test panel was exposed extreme
thermal conditions (humidity and temperature) within a climate
chamber to show that there is a general ingress of water to cabin
components and that this ingress of water leads to the change of
different mechanical properties.
Abstract: Absorption and fluorescence spectra of quinine
sulphate (QSD) have been recorded at room temperature in wide
range of solvents of different polarities. The ground-state dipole
moment of QSD was obtained from quantum mechanical calculations
and the excited state dipole moment of QSD was estimated from
Bakhshiev-s and Kawski-Chamma-Viallet-s equations by means of
solvatochromic shift method. Higher value of dipole moment is
observed for excited state as compared to the corresponding ground
state value and this is attributed to the more polar excited state of
QSD.
Abstract: In cancer progress, the optical properties of tissues
like absorption and scattering coefficient change, so by these
changes, we can trace the progress of cancer, even it can be applied
for pre-detection of cancer. In this paper, we investigate the effects of
changes of optical properties on light penetrated into tissues. The
diffusion equation is widely used to simulate light propagation into
biological tissues. In this study, the boundary integral method (BIM)
is used to solve the diffusion equation. We illustrate that the changes
of optical properties can modified the reflectance or penetrating light.
Abstract: Degradation of polymeric insulation systems of
electrical equipments increases the space charge density and the
concentration of electrical dipoles. By consequence, the maximum
values and the slopes of absorption/resorption (A/R) currents can
change with insulation systems ageing. In this paper, an analysis of
the nature of the A/R currents and the importance of their
components, especially the polarization current and the current given
by the space charge, is presented. The experimental study concerns
the A/R currents measurements of plane samples (made from
CALMICAGLAS tapes), virgin and thermally accelerated aged. The
obtained results show that the ageing process produces an increase of
the values and a decrease of shapes of the A/R currents. Finally, the
possibility of estimating insulations ageing state and lifetime from
A/R currents measurements is discussed.
Abstract: Solar energy is the most “available", ecological and clean energy. This energy can be used in active or passive mode. The active mode implies the transformation of solar energy into a useful energy. The solar energy can be transformed into thermal energy, using solar collectors. In these collectors, the active and the most important element is the absorber, material which performs the absorption of solar radiation and, in at the same time, limits its reflection. The paper presents some aspects regarding the IR absorbing material – a type of cermets, used as absorber in the solar collectors, by X Ray Diffraction Technique (XRD) characterization.
Abstract: The present paper deals with the experimental and
computational study of axial collapse of the aluminum metallic shells
having combined tube-frusta geometry between two parallel plates.
Shells were having bottom two third lengths as frusta and remaining
top one third lengths as tube. Shells were compressed to recognize
their modes of collapse and associated energy absorption capability.
An axisymmetric Finite Element computational model of collapse
process is presented and analysed, using a non-linear FE code
FORGE2. Six noded isoparametric triangular elements were used to
discretize the deforming shell. The material of the shells was
idealized as rigid visco-plastic. To validate the computational model
experimental and computed results of the deformed shapes and their
corresponding load-compression and energy-compression curves
were compared. With the help of the obtained results progress of the
axisymmetric mode of collapse has been presented, analysed and
discussed.
Abstract: The commercial finite element program LS-DYNA was employed to evaluate the response and energy absorbing capacity of cylindrical metal tubes that are externally wrapped with composite. The effects of composite wall thickness, loading conditions and fiber ply orientation were examined. The results demonstrate that a wrapped composite can be utilized effectively to enhance the crushing characteristics and energy absorbing capacity of the tubes. Increasing the thickness of the composite increases the mean force and the specific energy absorption under both static and dynamic crushing. The ply pattern affects the energy absorption capacity and the failure mode of the metal tube and the composite material property is also significant in determining energy absorption efficiency.
Abstract: A new chelating resin is prepared by coupling
Amberlite XAD-4 with 1-amino-2-naphthole through an azo spacer.
The resulting sorbent has been characterized by FT-IR, elemental
analysis and thermogravimetric analysis (TGA) and studied for
preconcentrating of Cu (II) using flame atomic absorption
spectrometry (FAAS) for metal monitoring. The optimum pH value
for sorption of the copper ions was 6.5. The resin was subjected to
evaluation through batch binding of mentioned metal ion.
Quantitative desorption occurs instantaneously with 0.5 M HNO3.
The sorption capacity was found 4.8 mmol.g-1 of resin for Cu (II) in
the aqueous solution. The chelating resin can be reused for 10 cycles
of sorption-desorption without any significant change in sorption
capacity. A recovery of 99% was obtained the metal ions with 0.5 M
HNO3 as eluting agent. The method was applied for metal ions
determination from industrial waste water sample.
Abstract: Owing to the stringent environmental legislations,
CO2 capture and sequestration is one of the viable solutions to reduce
the CO2 emissions from various sources. In this context, Ionic liquids
(ILs) are being investigated as suitable absorption media for CO2
capture. Due to their non-evaporative, non-toxic, and non-corrosive
nature, these ILs have the potential to replace the existing solvents
like aqueous amine solutions for CO2 separation technologies. Thus,
the present work aims at studying the important aspects such as the
interactions of CO2 molecule with different anions (F-, Br-, Cl-, NO3
-,
BF4
-, PF6
-, Tf2N-, and CF3SO3
-) that are commonly used in ILs
through molecular modeling. In this, the minimum energy structures
have been obtained using Ab initio based calculations at MP2
(Moller-Plesset perturbation) level. Results revealed various degrees
of distortion of CO2 molecule (from its linearity) with the anions
studied, most likely due to the Lewis acid-base interactions between
CO2 and anion. Furthermore, binding energies for the anion-CO2
complexes were also calculated. The implication of anion-CO2
interactions to the solubility of CO2 in ionic liquids is also discussed.
Abstract: Polarization modulation infrared reflection absorption
spectroscopy (PM-IRRAS) in combination with electrochemistry,
was employed to study the influence of surface charge (potential) on
the kinetics of bovine serum albumin (BSA) adsorption on a
biomedical-grade 316LVM stainless steel surface is discussed. The
BSA adsorption kinetics was found to greatly depend on the surface
potential. With an increase in surface potential towards more
negative values, both the BSA initial adsorption rate and the
equilibrium (saturated) surface concentration also increased. Both
effects were explained on the basis of replacement of well-ordered
water molecules at the 316LVM / solution interface, i.e. by the
increase in entropy of the system.
Abstract: The main aim of this research is to study the possible
use of recycled fine aggregate made from waste rubble wall to
substitute partially for the natural sand used in the production of
cement and sand bricks. The bricks specimens were prepared by
using 100% natural sand; they were then replaced by recycled fine
aggregate at 25, 50, 75, and 100% by weight of natural sand. A series
of tests was carried out to study the effect of using recycled aggregate
on the physical and mechanical properties of bricks, such as density,
drying shrinkage, water absorption characteristic, compressive and
flexural strength. Test results indicate that it is possible to
manufacture bricks containing recycled fine aggregate with good
characteristics that are similar in physical and mechanical properties
to those of bricks with natural aggregate, provided that the percentage
of recycled fine aggregates is limited up to 50-75%.
Abstract: In this work we study the reflection of circularly
polarised light from a nano-structured biological material found in
the exocuticle of scarabus beetles. This material is made of a stack
of ultra-thin (~5 nm) uniaxial layers arranged in a left-handed
helicoidal stack, which resonantly reflects circularly polarized light.
A chirp in the layer thickness combined with a finite absorption
coefficient produce a broad smooth reflectance spectrum. By
comparing model calculations and electron microscopy with
measured spectra we can explain our observations and quantify most
relevant structural parameters.
Abstract: In the present work we model a Multiquantum Well
structure Separate Absorption and Charge Multiplication Avalanche
Photodiode (MQW-SACM-APD), while the Absorption region
coincide with the MQW. We consider the nonuniformity of electric
field using split-step method in active region. This model is based on
the carrier rate equations in the different regions of the device. Using
the model we obtain the photocurrent, and dark current. As an
example, InGaAs/InP SACM-APD and MQW-SACM-APD are
simulated. There is a good agreement between the simulation and
experimental results.
Abstract: Environmental awareness and depletion of the
petroleum resources are among vital factors that motivate a number
of researchers to explore the potential of reusing natural fiber as an
alternative composite material in industries such as packaging,
automotive and building constructions. Natural fibers are available in
abundance, low cost, lightweight polymer composite and most
importance its biodegradability features, which often called “ecofriendly"
materials. However, their applications are still limited due
to several factors like moisture absorption, poor wettability and large
scattering in mechanical properties. Among the main challenges on
natural fibers reinforced matrices composite is their inclination to
entangle and form fibers agglomerates during processing due to
fiber-fiber interaction. This tends to prevent better dispersion of the
fibers into the matrix, resulting in poor interfacial adhesion between
the hydrophobic matrix and the hydrophilic reinforced natural fiber.
Therefore, to overcome this challenge, fiber treatment process is one
common alternative that can be use to modify the fiber surface
topology by chemically, physically or mechanically technique.
Nevertheless, this paper attempt to focus on the effect of
mercerization treatment on mechanical properties enhancement of
natural fiber reinforced composite or so-called bio composite. It
specifically discussed on mercerization parameters, and natural fiber
reinforced composite mechanical properties enhancement.
Abstract: In this study, the dispersed model is used to predict
gas phase concentration, liquid drop concentration. The venturi
scrubber efficiency is calculated by gas phase concentration. The
modified model has been validated with available experimental data
of Johnstone, Field and Tasler for a range of throat gas velocities,
liquid to gas ratios and particle diameters and is used to study the
effect of some design parameters on collection efficiency.
Abstract: The mixing of pollutions and sediments in near shore regions of natural water bodies depends heavily on the characteristics such as the strength and frequency of flow instability. In the present paper, the instability of natural convection induced by absorption of solar radiation in littoral regions is considered. Spectral analysis is conducted on the quasi-steady state flow to reveal the power and frequency modes of the instability at various positions. Results indicate that the power of instability, the number of frequency modes, the prominence of higher frequency modes, and the highest frequency mode increase with the offshore distance and/or Rayleigh number. Harmonic modes are present at relatively low Rayleigh numbers. For a given offshore distance, the position with the strongest power of instability is located adjacent to the sloping bottom while the frequency modes are the same over the local depth. As the Rayleigh number increases, the unstable region extends toward the shore.
Abstract: In spite of the advent of new materials, clay bricks
remain, arguably, the most popular construction materials today.
Nevertheless the low cost and versatility of clay bricks cannot always
be associated with high environmental and sustainable values,
especially in terms of raw material sources and manufacturing
processes. At the same time, the worldwide agricultural footprint is
fast growing, with vast agricultural land cultivation and active
expansion of the agro-based industry. The resulting large quantities of
agricultural wastes, unfortunately, are not always well managed or
utilised. These wastes can be recycled, such as by retrieving fibres
from disposed leaves and fruit bunches, and then incorporated in
brick-making. This way the clay bricks are made a 'greener' building
material and the discarded natural wastes can be reutilised, avoiding
otherwise wasteful landfill and harmful open incineration. This study
examined the physical and mechanical properties of clay bricks made
by adding two natural fibres to a clay-water mixture, with baked and
non-baked conditions. The fibres were sourced from pineapple leaves
(PF) and oil palm fruit bunch (OF), and added within the range of
0.25-0.75 %. Cement was added as a binder to the mixture at 5-15 %.
Although the two fibres had different effects on the bricks produced,
cement appeared to dominate the compressive strength. The
non-baked bricks disintegrated when submerged in water, while the
baked ones displayed cement-dependent characteristics in
water-absorption and density changes. Interestingly, further increase
in fibre content did not cause significant density decrease in both the
baked and non-baked bricks.
Abstract: Films of pure tin oxide SnO2 and in presence of
antimony atoms (SnO2-Sb) deposited onto glass substrates have
shown a sufficiently high energy gap to be transparent in the visible
region, a high electrical mobility and a carrier concentration which
displays a good electrical conductivity [1]. In this work, the effects of
polycrystalline silicon substrate on the optical properties of pure and
Sb doped tin oxide is investigated.
We used the APCVD (atmospheric pressure chemical vapour
deposition) technique, which is a low-cost and simple technique,
under nitrogen ambient, for growing this material. A series of SnO2
and SnO2-Sb have been deposited onto polycrystalline silicon
substrates with different contents of antimony atoms at the same
conditions of deposition (substrate temperature, flow oxygen,
duration and nitrogen atmosphere of the reactor). The effect of the
substrate in terms of morphology and nonlinear optical properties,
mainly the reflectance, was studied. The reflectance intensity of the
device, compared to the reflectance of tin oxide films deposited
directly on glass substrate, is clearly reduced on the overall
wavelength range. It is obvious that the roughness of the poly-c
silicon plays an important role by improving the reflectance and
hence the optical parameters.
A clear shift in the minimum of the reflectance upon doping level
is observed. This minimum corresponds to strong free carrier
absorption, resulting in different plasma frequency. This effect is
followed by an increase in the reflectance depending of the antimony
doping. Applying the extended Drude theory to the combining
optical and electrical obtained results these effects are discussed.
Abstract: The present study is concerned with the absorption
center of photophoresis within a micro-sized and spheroidal particle in
a gaseous medium. A particle subjected to an intense light beam can
absorb electromagnetic energy within the particle unevenly, which
results in photophoretic force to drive the particle in motion. By
evaluating the energy distribution systematically at various conditions,
the study focuses on the effects of governing parameters, such as
particle aspect ratio, size parameter, refractivity, and absorptivity, on
the heat source function within the particle and their potential
influences to the photophoresis.