Abstract: We present a dextran modified silicon microring
resonator sensor for high density antibody immobilization. An array
of sensors consisting of three sensor rings and a reference ring was
fabricated and its surface sensitivity and the limit of detection were
obtained using polyelectrolyte multilayers. The mass sensitivity and
the limit of detection of the fabricated sensor ring are 0.35 nm/ng
mm-2 and 42.8 pg/mm2 in air, respectively. Dextran modified sensor
surface was successfully prepared by covalent grafting of oxidized
dextran on 3-aminopropyltriethoxysilane (APTES) modified silicon
sensor surface. The antibody immobilization on hydrogel dextran
matrix improves 40% compared to traditional antibody
immobilization method via APTES and glutaraldehyde linkage.
Abstract: Polarization modulation infrared reflection absorption
spectroscopy (PM-IRRAS) in combination with electrochemistry,
was employed to study the influence of surface charge (potential) on
the kinetics of bovine serum albumin (BSA) adsorption on a
biomedical-grade 316LVM stainless steel surface is discussed. The
BSA adsorption kinetics was found to greatly depend on the surface
potential. With an increase in surface potential towards more
negative values, both the BSA initial adsorption rate and the
equilibrium (saturated) surface concentration also increased. Both
effects were explained on the basis of replacement of well-ordered
water molecules at the 316LVM / solution interface, i.e. by the
increase in entropy of the system.
Abstract: Visible Light Communication (VLC) offers advantages of low energy consumption, licence free and RF interference free operation. One application area for VLC is in the provision of health centred services circumventing issues of interference with any biomedical device within the environment. VLC performamce is affected by natural light restricting systems avilability and relibility. The paper presents an analysis of the performance of VLC systems under different meteorological conditions. The evaluation considered the impact of natural light as a function of different reflection surfaces in different room sizes.
Abstract: The nanofiber sheet of Multiwall Cabon Nanotube
(MWCNTs)/Polyacylonitile (PAN) composites was fabricated from
electrospun nanofiber. Firstly the surface of MWCNTs was
chemically modified, comparing two different techniques consisting
of admicellar polymerization and functionalization to improve the
dispersion and prevent the aggregation in the PAN matrix. The
modified MWCNTs were characterized by the dispersion in
dimethylformamide (DMF) solvent, Laser particle size, and FTRaman.
Lastly, DSC, SEM and mechanical properties of the
nanofiber sheet were examined. The results show that the mechanical
properties of the nanofiber sheet prepared from admicellar
polymerization-modified MWCNTs were higher than those of the
others.
Abstract: The aims of this paper are to study the efficacy of
chitosan nanoparticles in stimulating specific antibody against
A/H1N1 influenza antigen in mice. Chitosan nanoparticles (CSN)
were characterized by TEM. The results showed that the average size
of CSN was from 80nm to 106nm. The efficacy of A/H1N1 influenza
vaccine loaded on the surface of CSN showed that loading efficiency
of A/H1N1 influenza antigen on CSN was from 93.75 to 100%. Safe
property of the vaccine were tested. In 10 days post vaccination,
group of CSN 30 kDa and 300 kDa loaded A/H1N1 influenza antigen
were the rate of immune response on mice to be 100% (9/9) higher
than Al(OH)3 and other adjuvant. 100% mice in the experiment of all
groups had immune response in 20 days post vaccination. The results
also showed that HI titer of the group using CSN 300 kDa as an
adjuvant increased significantly up to 3971 HIU, over three-fold
higher than the Al(OH)3 adjuvant, chitosan (CS), and one hundredfold
than the A/H1N1 antigen only. Stability of the vaccine
formulation was investigated.
Abstract: A numerical analysis of wave and hydrodynamic models
is used to investigate the influence of WAve and Storm Surge
(WASS) in the regional and coastal zones. The numerical analyzed
system consists of the WAve Model Cycle 4 (WAMC4) and the
Princeton Ocean Model (POM) which used to solve the energy
balance and primitive equations respectively. The results of both
models presented the incorporated surface wave in the regional
zone affected the coastal storm surge zone. Specifically, the results
indicated that the WASS generally under the approximation is not
only the peak surge but also the coastal water level drop which
can also cause substantial impact on the coastal environment. The
wave–induced surface stress affected the storm surge can significantly
improve storm surge prediction. Finally, the calibration of wave
module according to the minimum error of the significant wave height
(Hs) is not necessarily result in the optimum wave module in the
WASS analyzed system for the WASS prediction.
Abstract: The development and extension of large cities induced
a need for shallow tunnel in soft ground of building areas. Estimation
of ground settlement caused by the tunnel excavation is important
engineering point. In this paper, prediction of surface subsidence
caused by tunneling in one section of seventh line of Tehran subway
is considered. On the basis of studied geotechnical conditions of the
region, tunnel with the length of 26.9km has been excavated applying
a mechanized method using an EPB-TBM with a diameter of 9.14m.
In this regard, settlement is estimated utilizing both analytical and
numerical finite element method. The numerical method shows that
the value of settlement in this section is 5cm. Besides, the analytical
consequences (Bobet and Loganathan-Polous) are 5.29 and 12.36cm,
respectively. According to results of this study, due tosaturation of
this section, there are good agreement between Bobet and numerical
methods. Therefore, tunneling processes in this section needs a
special consolidation measurement and support system before the
passage of tunnel boring machine.
Abstract: Coated tool inserts can be considered as the backbone
of machining processes due to their wear and heat resistance.
However, defects of coating can degrade the integrity of these inserts
and the number of these defects should be minimized or eliminated if
possible. Recently, the advancement of coating processes and
analytical tools open a new era for optimizing the coating tools.
First, an overview is given regarding coating technology for cutting
tool inserts. Testing techniques for coating layers properties, as well
as the various coating defects and their assessment are also surveyed.
Second, it is introduced an experimental approach to examine the
possible coating defects and flaws of worn multicoated carbide
inserts using two important techniques namely scanning electron
microscopy and atomic force microscopy. Finally, it is
recommended a simple procedure for investigating manufacturing
defects and flaws of worn inserts.
Abstract: The need to evaluate and understand the natural
drainage pattern in a flood prone, and fast developing environment is
of paramount importance. This information will go a long way to
help the town planners to determine the drainage pattern, road
networks and areas where prominent structures are to be located. This
research work was carried out with the aim of studying the Bayelsa
landscape topography using digitized topographic information, and to
model the natural drainage flow pattern that will aid the
understanding and constructions of workable drainages. To achieve
this, digitize information of elevation and coordinate points were
extracted from a global imagery map. The extracted information was
modeled into 3D surfaces. The result revealed that the average
elevation for Bayelsa State is 12 m above sea level. The highest
elevation is 28 m, and the lowest elevation 0 m, along the coastline.
In Yenagoa the capital city of Bayelsa were a detail survey was
carried out showed that average elevation is 15 m, the highest
elevation is 25 m and lowest is 3 m above the mean sea level. The
regional elevation in Bayelsa, showed a gradation decrease from the
North Eastern zone to the South Western Zone. Yenagoa showed an
observed elevation lineament, were low depression is flanked by high
elevation that runs from the North East to the South west. Hence,
future drainages in Yenagoa should be directed from the high
elevation, from South East toward the North West and from the
North West toward South East, to the point of convergence which is
at the center that flows from South East toward the North West.
Bayelsa when considered on a regional Scale, the flow pattern is from
the North East to the South West, and also North South. It is
recommended that in the event of any large drainage construction at
municipal scale, it should be directed from North East to the South
West or from North to South. Secondly, detail survey should be
carried out to ascertain the local topography and the drainage pattern
before the design and construction of any drainage system in any part
of Bayelsa.
Abstract: Air emissions from waste treatment plants often
consist of a combination of Volatile Organic Compounds (VOCs)
and odors. Hydrogen sulfide is one of the major odorous gases
present in the waste emissions coming from municipal wastewater
treatment facilities. Hydrogen sulfide (H2S) is odorous, highly toxic
and flammable. Exposure to lower concentrations can result in eye
irritation, a sore throat and cough, shortness of breath, and fluid in
the lungs. Biofiltration has become a widely accepted technology for
treating air streams containing H2S. When compared with other nonbiological
technologies, biofilter is more cost-effective for treating large
volumes of air containing low concentrations of biodegradable compounds.
Optimization of biofilter media is essential for many reasons such as:
providing a higher surface area for biofilm growth, low pressure drop,
physical stability, and good moisture retention. In this work, a novel
biofilter media is developed and tested at a pumping station of a
municipality located in the United Arab Emirates (UAE). The
media is found to be very effective (>99%) in removing H2S
concentrations that are expected in pumping stations under steady
state and shock loading conditions.
Abstract: This study was conducted to investigate the incidence
of pathogenic bacteria: Salmonella, Shigella, Escherichia coli O157
and Staphylococcus aureus in cakes and tarts collected from thirtyfive
confectionery producing and selling premises located within
Tripoli city, Libya. The results revealed an incidence of S. aureus
with 94.4 and 48.0 %, E. coli O157 with 14.7 and 4.0 % and Salmonella
sp. with 5.9 and 8.0 % in cakes and tarts samples respectively;
while Shigella was not detected in all samples. In order to determine
the source of these pathogenic bacteria, cotton swabs were taken
from the hands of workers on the production line, the surfaces of
preparation tables and cream whipping instruments. The results
showed that the cotton swabs obtained from the hands of workers
contained S. aureus and Salmonella sp. with an incidence of 42.9 and
2.9 %, the cotton swabs obtained from the surfaces of preparation
tables 22.9 and 2.9 % and the cotton swabs obtained from the cream
whipping instruments 14.3 and 0.0 % respectively; while E. coli
O157 and Shigella sp. were not detected in all swabs. Additionally,
other bacteria were isolated from the hands of workers and the Surfaces
of producing equipments included: Aeromonas sp., Pseudomonas
sp., E. coli, Klebsiella sp., Enterobacter sp., Citrobacter sp.,
Proteus sp., Serratia sp. and Acinetobacter sp. These results indicate
that some of the cakes and tarts might pose threat to consumer's
health. Meanwhile, occurrences of pathogenic bacteria on the hands
of those who are working in production line and the surfaces of
equipments reflect poor hygienic practices at most confectionery
premises examined in this study. Thus, firm and continuous surveillance
of these premises is needed to insure the consumer's health and
safety.
Abstract: A new robust nonlinear control scheme of a manipulator is proposed in this paper which is robust against modeling errors and unknown disturbances. It is based on the principle of variable structure control, with sliding mode control (SMC) method. The variable structure control method is a robust method that appears to be well suited for robotic manipulators because it requers only bounds on the robotic arm parameters. But there is no single systematic procedure that is guaranteed to produce a suitable control law. Also, to reduce chattring of the control signal, we replaced the sgn function in the control law by a continuous approximation such as tangant function. We can compute the maximum load with regard to applied torque into joints. The effectivness of the proposed approach has been evaluated analitically demonstrated through computer simulations for the cases of variable load and robot arm parameters.
Abstract: This study aims to demonstrate the quantification of
peptides based on isotope dilution surface enhanced Raman
scattering (IDSERS). SERS spectra of phenylalanine (Phe), leucine
(Leu) and two peptide sequences TGQIFK (T13) and
YSFLQNPQTSLCFSESIPTPSNR (T6) as part of the 22-kDa
human growth hormone (hGH) were obtained on Ag-nanoparticle
covered substrates. On the basis of the dominant Phe and Leu
vibrational modes, precise partial least squares (PLS) prediction
models were built enabling the determination of unknown T13 and
T6 concentrations. Detection of hGH in its physiological
concentration in order to investigate the possibility of protein
quantification has been achieved.
Abstract: An advanced composite flywheel rotor consisting of
intra and inter hybrid rims was designed to optimally increase the energy capacity, and was manufactured using filament winding with
in-situ curing. The flywheel has recently attracted considerable attention from many investigators since it possesses great potential in
many energy storage applications, including electric utilities, hybrid or
electric automobiles, and space vehicles. In this investigation, a comprehensive study was conducted with the intent to implement
composites in high performance flywheel applications.The inner two
intra-hybrid rims (rims 1 and 2) were manufactured as a whole part
through continuous filament winding under in-situ curing conditions,
and so were the outer two rims (rims 3 and 4). The outer surface of rim
2 and the inner surface of rim 3 were CNC-tapered for press-fitting. Machined rims were finally press-fitted using a hydraulic press with a
maximum compressive force of approximately 1000 ton.
Abstract: The necessity of updating the numerical models inputs, because of geometrical and resistive variations in rivers subject to solid transport phenomena, requires detailed control and monitoring activities. The human employment and financial resources of these activities moves the research towards the development of expeditive methodologies, able to evaluate the outflows through the measurement of more easily acquirable sizes. Recent studies highlighted the dependence of the entropic parameter on the kinematical and geometrical flow conditions. They showed a meaningful variability according to the section shape, dimension and slope. Such dependences, even if not yet well defined, could reduce the difficulties during the field activities, and also the data elaboration time. On the basis of such evidences, the relationships between the entropic parameter and the geometrical and resistive sizes, obtained through a large and detailed laboratory experience on steady free surface flows in conditions of macro and intermediate homogeneous roughness, are analyzed and discussed.
Abstract: An ultrasound-assisted activation method for
electroless silver plating is presented in this study. When the
ultrasound was applied during the activation step, the amount of the Pd
species adsorbed on substrate surfaces was higher than that of sample
pretreated with a conventional activation process without ultrasound
irradiation. With this activation method, it was also shown that the
adsorbed Pd species with a size of about 5 nm were uniformly
distributed on the surfaces, thus a smooth and uniform coating on the
surfaces was obtained by subsequent electroless silver plating. The
samples after each step were characterized by AFM, XPS, FIB, and
SEM.
Abstract: Numerical simulations are performed for laminar
continuous and pulsed jets impinging on a surface in order to
investigate the effects of pulsing frequency on the heat transfer
characteristics. The time-averaged Nusselt number of pulsed jets is
larger in the impinging jet region as compared to the continuous jet,
while it is smaller in the outer wall jet region. At the stagnation point,
the mean and RMS Nusselt numbers become larger and smaller,
respectively, as the pulsing frequency increases. Unsteady behaviors
of vortical fluid motions and temperature field are also investigated to
understand the underlying mechanisms of heat transfer enhancement.
Abstract: Work is focused to the study of unburned carbon in
ash from coal (and wastes) combustion in 8 combustion tests at 3
fluidised-bed power station, at co-combustion of coal and wastes
(also at fluidized bed) and at bench-scale unit simulating coal
combustion in small domestic furnaces. The attention is paid to
unburned carbon contents in bottom ashes and fly ashes at these 8
combustion tests and to morphology of unburned carbons. Specific
surface area of coals, unburned carbons and ashes and the relation of
specific surface area of unburned carbon and the content of volatile
combustibles in coal were studied as well.
Abstract: Fly ash is a significant waste that is released of
thermal power plants and defined as very fine particles that are drifted upward with up taken by the flue gases due to the burning of
used coal [1]. The fly-ash is capable of removing organic
contaminants in consequence of high carbon content, a large surface area per unit volume and contained heavy metals. Therefore, fly ash
is used as an effective coagulant and adsorbent by pelletization [2, 3].
In this study, the possibility of use of fly ash taken from Turkey like low-cost adsorbent for adsorption of zinc ions found in waste
water was investigated. The fly ash taken from Turkey was pelletized with bentonite and molass to evaluate the adsorption capaticity. For
this purpose; analyses such as sieve analysis, XRD, XRF, FTIR and SEM were performed. As a result, it was seen that pellets prepared
from fly ash, bentonite and molass would be used for zinc adsorption.
Abstract: Nowadays, engineering ceramics have significant
applications in different industries such as; automotive, aerospace,
electrical, electronics and even martial industries due to their
attractive physical and mechanical properties like very high hardness
and strength at elevated temperatures, chemical stability, low friction
and high wear resistance. However, these interesting properties plus
low heat conductivity make their machining processes too hard,
costly and time consuming. Many attempts have been made in order
to make the grinding process of engineering ceramics easier and
many scientists have tried to find proper techniques to economize
ceramics' machining processes. This paper proposes a new diamond
plunge grinding technique using ultrasonic vibration for grinding
Alumina ceramic (Al2O3). For this purpose, a set of laboratory
equipments have been designed and simulated using Finite Element
Method (FEM) and constructed in order to be used in various
measurements. The results obtained have been compared with the
conventional plunge grinding process without ultrasonic vibration
and indicated that the surface roughness and fracture strength
improved and the grinding forces decreased.