Abstract: Customarily, the LMTD correction factor, FT, is used
to screen alternative designs for a heat exchanger. Designs with
unacceptably low FT values are discarded. In this paper, authors have
proposed a more fundamental criterion, based on feasibility of a
multipass exchanger as the only criteria, followed by economic
optimization. This criterion, coupled with asymptotic energy targets,
provide the complete optimization space in a heat exchanger network
(HEN), where cost-optimization of HEN can be performed with only
Heat Recovery Approach temperature (HRAT) and number-of-shells
as variables.
Abstract: The common practice of operating S-rotor is in an
open environment; however there are times when the rotor is
installed in a bounded environment and there might be changes in the
performance of the rotor. This paper presents the changes in the
performance of S-rotor when operated in bounded flows. The
investigation was conducted experimentally to compare the
performance of the rotors in bounded environment against open
environment. Three different rotors models were designed, fabricated
and subjected to experimental measurements. All of the three models
were having 600 mm height and 300 mm Diameter. They were tested
in three different flow environments; namely: partially bounded
environment, fully bounded environment and open environment.
Rotors were found to have better starting up capabilities when
operated in bounded environment. Apart from that, all rotors manage
to achieve higher Power and Torque Coefficients at a higher Tip
Speed Ratio as compared to the open environment.
Abstract: The 15-a-side Fiji rugby team trains well in preparations for any rugby competition but rarely performs to expectations. In order to help the Fiji local based rugby players to identify some key basic areas in improving their performance, a series of workshops were conducted to assess their nutritional status and dietary habits in relation to energy demand during rugby matches. The nutrition workshop included the administration of questionnaires to 19 local based rugby players, requesting the following information: usual food intakes, training camp food intakes, carbohydrate loading, pre-game meals and post-game meals. The study revealed that poor eating habits of the players resulted in the low carbohydrate intake, which may have contributed to increase levels of fatigue leading to loss of stamina even before the second half of the game. It appears that the diet of most 15-a-side players does not provide enough energy to enable them to last the full eightyminutes of the game.
Abstract: Both the minimum energy consumption and
smoothness, which is quantified as a function of jerk, are generally
needed in many dynamic systems such as the automobile and the
pick-and-place robot manipulator that handles fragile equipments.
Nevertheless, many researchers come up with either solely
concerning on the minimum energy consumption or minimum jerk
trajectory. This research paper considers the indirect minimum Jerk
method for higher order differential equation in dynamics
optimization proposes a simple yet very interesting indirect jerks
approaches in designing the time-dependent system yielding an
alternative optimal solution. Extremal solutions for the cost functions
of indirect jerks are found using the dynamic optimization methods
together with the numerical approximation. This case considers the
linear equation of a simple system, for instance, mass, spring and
damping. The simple system uses two mass connected together by
springs. The boundary initial is defined the fix end time and end
point. The higher differential order is solved by Galerkin-s methods
weight residual. As the result, the 6th higher differential order shows
the faster solving time.
Abstract: This paper presents an experimental investigation using Acoustic Emission (AE) technology to monitor sand transportation in multiphase flow. The investigations were undertaken on three-phase (air-water-sand) flow in a horizontal pipe where the superficial gas velocity (VSG) had a range of between 0.2msˉ¹ to 2.0msˉ¹ and superficial liquid velocity (VSL) had a range of between 0.2msˉ¹ to 1.0msˉ¹. The experimental findings clearly show a correlation exists between AE energy levels, sand concentration, superficial gas velocity (VSG), and superficial liquid velocity (VSL).
Abstract: Axial Flux Permanent Magnet (AFPM) Machines require effective cooling due to their high power density. The detrimental effects of overheating such as degradation of the insulation materials, magnets demagnetization, and increase of Joule losses are well known. This paper describes the CFD simulations performed on a test rig model of an air cooled Axial Flux Permanent Magnet (AFPM) generator built at Durham University to identify the temperatures and heat transfer coefficient on the stator. The Reynolds Averaged Navier-Stokes and the Energy equations are solved and the flow pattern and heat transfer developing inside the machine are described. The Nusselt number on the stator surfaces has been found. The dependency of the heat transfer on the flow field is described temperature field obtained. Tests on an experimental are undergoing in order to validate the CFD results.
Abstract: In the process of polyethylene extrusion polymer
material similar to powder or granule is under compression, melting
and transmission operation and on base of special form, extrudate has
been produced. Twin-screw extruders are applicable in industries
because of their high capacity. The powder mixing with chemical
additives and melting with thermal and mechanical energy in three
zones (feed, compression and metering zone) and because of gear
pump and screw's pressure, converting to final product in latest plate.
Extruders with twin-screw and short distance between screws are
better than other types because of their high capacity and good
thermal and mechanical stress.
In this paper, process of polyethylene extrusion and various tapes
of extruders are studied. It is necessary to have an exact control on
process to producing high quality products with safe operation and
optimum energy consumption.
The granule size is depending on granulator motor speed. Results
show at constant feed rate a decrease in granule size was found whit
Increase in motor speed. Relationships between HDPE feed rate and
speed of granulator motor, main motor and gear pump are calculated
following as:
x = HDPE feed flow rate, yM = Main motor speed
yM = (-3.6076e-3) x^4+ (0.24597) x^3+ (-5.49003) x^2+ (64.22092)
x+61.66786 (1)
x = HDPE feed flow rate, yG = Gear pump speed
yG = (-2.4996e-3) x^4+ (0.18018) x^3+ (-4.22794) x^2+ (48.45536)
x+18.78880 (2)
x = HDPE feed flow rate, y = Granulator motor speed
10th Degree Polynomial Fit: y = a+bx+cx^2+dx^3... (3)
a = 1.2751, b = 282.4655, c = -165.2098,
d = 48.3106, e = -8.18715, f = 0.84997
g = -0.056094, h = 0.002358, i = -6.11816e-5
j = 8.919726e-7, k = -5.59050e-9
Abstract: A modified Genetic Algorithm (GA) based optimal selection of parameters for Automatic Generation Control (AGC) of multi-area electric energy systems is proposed in this paper. Simulations on multi-area reheat thermal system with and without consideration of nonlinearity like governor dead band followed by 1% step load perturbation is performed to exemplify the optimum parameter search. In this proposed method, a modified Genetic Algorithm is proposed where one point crossover with modification is employed. Positional dependency in respect of crossing site helps to maintain diversity of search point as well as exploitation of already known optimum value. This makes a trade-off between exploration and exploitation of search space to find global optimum in less number of generations. The proposed GA along with decomposition technique as developed has been used to obtain the optimum megawatt frequency control of multi-area electric energy systems. Time-domain simulations are conducted with trapezoidal integration along with decomposition technique. The superiority of the proposed method over existing one is verified from simulations and comparisons.
Abstract: This research deals with investigations on the “Active
Generator" under rotor speed variations and output frequency
control. It runs at turbine speed and it is connected to a three phase
electrical power grid which has its own frequency different from
turbine frequency. In this regard the set composed of a four phase
synchronous generator and a natural commutated matrix converter
(NCMC) made with thyristors, is called active generator. It replaces a
classical mechanical gearbox which introduces many drawbacks. The
main idea in this article is the presentation of frequency control at
grid side when turbine runs at variable speed. Frequency control has
been done by linear and step variations of the turbine speed. Relation
between turbine speed (frequency) and main grid zero sequence
voltage frequency is presented.
Abstract: From the perspective of industrial structure
coordination and based on an explicit definition for the connotation of
industrial structure coordination, the synergetic coefficients are used
to measure the coordination degree between three industries' input
structure and output structure, and then the efficacy function method is
employed to comprehensively evaluate the level of China-s industrial
structure optimization. It is showed that Chinese industrial structure
presented a "v-shaped" variation tendency between 1996 and 2008,
and its industrial structure adjustment got obvious achievements after
2003, with the industrial structure optimization level increasing
continuously. However in 2009, the level of China-s industrial
structure optimization declined sharply due to the decreasing
contribution degree of value added structure and energy structure
coordination and the lower coordination degree of value added
structure and capital structure.
Abstract: Hypertension is characterized with stress on the heart and blood vessels thus increasing the risk of heart attack and renal diseases. The Renin angiotensin system (RAS) plays a major role in blood pressure control. Renin is the enzyme that controls the RAS at the rate-limiting step. Our aim is to develop new drug-like leads which can inhibit renin and thereby emerge as therapeutics for hypertension. To achieve this, molecular dynamics (MD) simulation and receptor-based pharmacophore modeling were implemented, and three rennin-inhibitor complex structures were selected based on IC50 value and scaffolds of inhibitors. Three pharmacophore models were generated considering conformations induced by inhibitor. The compounds mapped to these models were selected and subjected to drug-like screening. The identified hits were docked into the active site of renin. Finally, hit1 satisfying the binding mode and interaction energy was selected as possible lead candidate to be used in novel renin inhibitors.
Abstract: In this paper the optimal control strategy for
Permanent Magnet Synchronous Motor (PMSM) based drive system
is presented. The designed full optimal control is available for speed
operating range up to base speed. The optimal voltage space-vector
assures input energy reduction and stator loss minimization,
maintaining the output energy in the same limits with the
conventional PMSM electrical drive. The optimal control with three
components is based on the energetically criteria and it is applicable
in numerical version, being a nonrecursive solution. The simulation
results confirm the increased efficiency of the optimal PMSM drive.
The properties of the optimal voltage space vector are shown.
Abstract: Like any sentient organism, a smart environment
relies first and foremost on sensory data captured from the real
world. The sensory data come from sensor nodes of different
modalities deployed on different locations forming a Wireless Sensor
Network (WSN). Embedding smart sensors in humans has been a
research challenge due to the limitations imposed by these sensors
from computational capabilities to limited power. In this paper, we
first propose a practical WSN application that will enable blind
people to see what their neighboring partners can see. The challenge
is that the actual mapping between the input images to brain pattern
is too complex and not well understood. We also study the
connectivity problem in 3D/2D wireless sensor networks and propose
distributed efficient algorithms to accomplish the required
connectivity of the system. We provide a new connectivity algorithm
CDCA to connect disconnected parts of a network using cooperative
diversity. Through simulations, we analyze the connectivity gains
and energy savings provided by this novel form of cooperative
diversity in WSNs.
Abstract: This paper presents a technique for diagnosis of the abdominal aorta aneurysm in magnetic resonance imaging (MRI) images. First, our technique is designed to segment the aorta image in MRI images. This is a required step to determine the volume of aorta image which is the important step for diagnosis of the abdominal aorta aneurysm. Our proposed technique can detect the volume of aorta in MRI images using a new external energy for snakes model. The new external energy for snakes model is calculated from Law-s texture. The new external energy can increase the capture range of snakes model efficiently more than the old external energy of snakes models. Second, our technique is designed to diagnose the abdominal aorta aneurysm by Bayesian classifier which is classification models based on statistical theory. The feature for data classification of abdominal aorta aneurysm was derived from the contour of aorta images which was a result from segmenting of our snakes model, i.e., area, perimeter and compactness. We also compare the proposed technique with the traditional snakes model. In our experiment results, 30 images are trained, 20 images are tested and compared with expert opinion. The experimental results show that our technique is able to provide more accurate results than 95%.
Abstract: The Wind Turbine Modeling in Wind Energy Conversion System (WECS) using Doubly-Fed Induction Generator (DFIG) PI Controller based design is presented. To study about the variable wind speed. The PI controller performs responding to the dynamic performance. The objective is to study the characteristic of wind turbine and finding the optimum wind speed suitable for wind turbine performance. This system will allow the specification setting (2.5MW). The output active power also corresponding same the input is given. And the reactive power produced by the wind turbine is regulated at 0 Mvar. Variable wind speed is optimum for drive train performance at 12.5 m/s (at maximum power coefficient point) from the simulation of DFIG by Simulink is described.
Abstract: Developments in communication technologies
especially in wireless have enabled the progress of low-cost and lowpower
wireless sensor networks (WSNs). The features of such WSN
are holding minimal energy, weak computational capabilities,
wireless communication and an open-medium nature where sensors
are deployed. WSN is underpinned by application driven such as
military applications, the health sector, etc. Due to the intrinsic nature
of the network and application scenario, WSNs are vulnerable to
many attacks externally and internally. In this paper we have focused
on the types of internal attacks of WSNs based on OSI model and
discussed some security requirements, characterizers and challenges
of WSNs, by which to contribute to the WSN-s security research.
Abstract: Segmentation of a color image composed of different
kinds of regions can be a hard problem, namely to compute for an
exact texture fields. The decision of the optimum number of
segmentation areas in an image when it contains similar and/or un
stationary texture fields. A novel neighborhood-based segmentation
approach is proposed. A genetic algorithm is used in the proposed
segment-pass optimization process. In this pass, an energy function,
which is defined based on Markov Random Fields, is minimized. In
this paper we use an adaptive threshold estimation method for image
thresholding in the wavelet domain based on the generalized
Gaussian distribution (GGD) modeling of sub band coefficients. This
method called Normal Shrink is computationally more efficient and
adaptive because the parameters required for estimating the threshold
depend on sub band data energy that used in the pre-stage of
segmentation. A quad tree is employed to implement the multi
resolution framework, which enables the use of different strategies at
different resolution levels, and hence, the computation can be
accelerated. The experimental results using the proposed
segmentation approach are very encouraging.
Abstract: With the rapid advanced of technology, the industrial processes become increasingly demanding, from the point of view, power quality and controllability. The advent of multi levels inverters responds partially to these requirements. But actually, the new generation of multi-cells inverters permits to reach more performances, since, it offers more voltage levels. The disadvantage in the increase of voltage levels by the number of cells in cascades is on account of series igbts synchronisation loss, from where, a limitation of cells in cascade to 4. Regarding to these constraints, a new topology is proposed in this paper, which increases the voltage levels of the three-cell inverter from 4 to 8; with the same number of igbts, and using less stored energy in the flaying capacitors. The details of operation and modelling of this new inverter structure are also presented, then tested thanks to a three phase induction motor. KeywordsFlaying capacitors, Multi-cells inverter, pwm, switchers, modelling.
Abstract: The present work deals with the structural analysis of
turbine blades and modeling of turbine blades. A common failure
mode for turbine machines is high cycle of fatigue of compressor and
turbine blades due to high dynamic stresses caused by blade vibration
and resonance within the operation range of the machinery. In this
work, proper damping system will be analyzed to reduce the
vibrating blade. The main focus of the work is the modeling of under
platform damper to evaluate the dynamic analysis of turbine-blade
vibrations. The system is analyzed using Bond graph technique. Bond
graph is one of the most convenient ways to represent a system from
the physical aspect in foreground. It has advantage of putting together
multi-energy domains of a system in a single representation in a
unified manner. The bond graph model of dry friction damper is
simulated on SYMBOLS-shakti® software. In this work, the blades
are modeled as Timoshenko beam. Blade Vibrations under different
working conditions are being analyzed numerically.
Abstract: Where renewable energy sources, solar, hydro, wind are available the remote communities and businesses can be provided with the most reliable and affordable source of electrical energy. This paper presents a model of safari rest contains all the necessary services for the interested tourists who visit the safari Sinai desert. The PV energy system provides the rural energy needs of remote communities. A photovoltaic renewable energy system is designed to feed the global Ac and Dc electrical required load of this safari rest . The benefits of photovoltaic renewable energy at rural applications are its versatility and convenience. This model of safari rest must be taken in consideration by Egyptian Government as it will provide the tourism plane by new interested tourism field which put a big spot on Red sea area: El Ghordaka.