Abstract: In this paper, a Dynamic Economic Dispatch (DED) model is developed for the system consisting of both thermal generators and wind turbines. The inclusion of a significant amount of wind energy into power systems has resulted in additional constraints on DED to accommodate the intermittent nature of the output. The probability of stochastic wind power based on the Weibull probability density function is included in the model as a constraint; A Here-and-Now Approach. The Environmental Protection Agency-s hourly emission target, which gives the maximum emission during the day, is used as a constraint to reduce the atmospheric pollution. A 69-bus test system with non-smooth cost function is used to illustrate the effectiveness of the proposed model compared with static economic dispatch model with including the wind power.
Abstract: In this note, a theoretical model for analyzing of
normal penetration of the ogive – nose projectile into metallic targets
is presented .The failure is assumed to be asymmetry petalling and
the analysis is performed by using the energy balance and work done
.The work done consist of the work required for plastic deformation
Wp, the work for transferring the matter to new position Wd and the
work for bending of the petals Wb. In several studies, it has been
shown that we can neglect the loss of energy by temperature.
In this present study, in first, by assuming the crater formation
after perforation, the value of work done is calculated during the
normal penetration of conical projectiles into thin metallic targets.
Then the value of residual velocity and ballistic limit of the projectile
is predicated by using the energy balance. In final, theoretical and
experimental results is compared.
Abstract: Sensor Network are emerging as a new tool for
important application in diverse fields like military surveillance,
habitat monitoring, weather, home electrical appliances and others.
Technically, sensor network nodes are limited in respect to energy
supply, computational capacity and communication bandwidth. In
order to prolong the lifetime of the sensor nodes, designing efficient
routing protocol is very critical. In this paper, we illustrate the
existing routing protocol for wireless sensor network using data
centric approach and present performance analysis of these protocols.
The paper focuses in the performance analysis of specific protocol
namely Directed Diffusion and SPIN. This analysis reveals that the
energy usage is important features which need to be taken into
consideration while designing routing protocol for wireless sensor
network.
Abstract: The issue of real-time and reliable report delivery is extremely important for taking effective decision in a real world mission critical Wireless Sensor Network (WSN) based application. The sensor data behaves differently in many ways from the data in traditional databases. WSNs need a mechanism to register, process queries, and disseminate data. In this paper we propose an architectural framework for data placement and management. We propose a reliable and real time approach for data placement and achieving data integrity using self organized sensor clusters. Instead of storing information in individual cluster heads as suggested in some protocols, in our architecture we suggest storing of information of all clusters within a cell in the corresponding base station. For data dissemination and action in the wireless sensor network we propose to use Action and Relay Stations (ARS). To reduce average energy dissipation of sensor nodes, the data is sent to the nearest ARS rather than base station. We have designed our architecture in such a way so as to achieve greater energy savings, enhanced availability and reliability.
Abstract: Gliding during night without electric power is an efficient method to enhance endurance performance of solar aircrafts. The properties of maximum gliding endurance path are studied in this paper. The problem is formulated as an optimization problem about maximum endurance can be sustained by certain potential energy storage with dynamic equations and aerodynamic parameter constrains. The optimal gliding path is generated based on gauss pseudo-spectral method. In order to analyse relationship between altitude, velocity of solar UAVs and its endurance performance, the lift coefficient in interval of [0.4, 1.2] and flight envelopes between 0~30km are investigated. Results show that broad range of lift coefficient can improve solar aircrafts- long endurance performance, and it is possible for a solar aircraft to achieve the aim of long endurance during whole night just by potential energy storage.
Abstract: In this paper, the energy performance of a selected
UHDE Ammonia plant is optimized by conducting heat integration through waste heat recovery and the synthesis of a heat exchange
network (HEN). Minimum hot and cold utility requirements were estimated through IChemE spreadsheet. Supporting simulation was
carried out using HYSYS software. The results showed that there is
no need for heating utility while the required cold utility was found to
be around 268,714 kW. Hence a threshold pinch case was faced. Then, the hot and cold streams were matched appropriately. Also,
waste heat recovered resulted with savings in HP and LP steams of
approximately 51.0% and 99.6%, respectively. An economic analysis
on proposed HEN showed very attractive overall payback period not
exceeding 3 years. In general, a net saving approaching 35% was
achieved in implementing heat optimization of current studied UHDE Ammonia process.
Abstract: Solar energy is not only sustainable but also a clean
alternative to be used as source of high temperature heat for many
processes and power generation. However, the major drawback of
solar energy is its transient nature. Especially in solar
thermochemical processing, it is crucial to maintain constant or semiconstant
temperatures inside the solar reactor. In our laboratory, we
have developed a mechanism allowing us to achieve semi-constant
temperature inside the solar reactor. In this paper, we introduce the
concept along with some updated designs and provide the optical
analysis of the concept under various incoming flux.
Abstract: The experiment was performed to study the
relationship between excreta viscosity and Nitrogen-corrected true
metabolisable energy quantities of soybean meals using conventional
addition method (CAM) in adult cockerels for 7 d: a 3-d preexperiment
and a 4-d experiment period. Results indicated that
differences between the excreta viscosity values were (P
Abstract: Wireless Sensor Networks can be used to monitor the
physical phenomenon in such areas where human approach is nearly
impossible. Hence the limited power supply is the major constraint of
the WSNs due to the use of non-rechargeable batteries in sensor
nodes. A lot of researches are going on to reduce the energy
consumption of sensor nodes. Energy map can be used with
clustering, data dissemination and routing techniques to reduce the
power consumption of WSNs. Energy map can also be used to know
which part of the network is going to fail in near future. In this paper,
Energy map is constructed using the prediction based approach.
Adaptive alpha GM(1,1) model is used as the prediction model.
GM(1,1) is being used worldwide in many applications for predicting
future values of time series using some past values due to its high
computational efficiency and accuracy.
Abstract: We attempted investigate a boat model, based on the
conversion of energy of surface wave into a sequence of
unidirectional pulses of jet spurts, in other words - model of the boat,
which is thrusting by the waves field on water surface. These pulses
are forming some average reactive stream from the output nozzle on
the stern of boat. The suggested model provides the conversion of its
oscillatory motions (both pitching and rolling) into a jet flow. This
becomes possible due to special construction of the boat and due to
several details, sensitive to the local wave field. The boat model
presents the uniflow jet engine without slow conversions of
mechanical energy into intermediate forms and without any external
sources of energy (besides surface waves). Motion of boat is
characterized by fast jerks and average onward velocity, which
exceeds the velocities of liquid particles in the wave.
Abstract: A comprehensive discussion of feasible strategies for sustainable energy supply is urgently needed to achieve a turnaround of the current energy situation. The necessary fundamentals required for the development of a long term energy vision are lacking to a great extent due to the absence of reasonable long term scenarios that fulfill the requirements of climate protection and sustainable energy use. The contribution of the study is based on a search for sustainable energy paths in the long run for Austria. The analysis makes use of secondary data predominantly. The measures developed to avoid CO2 emissions and other ecological risk factors vary to a great extent among all economic sectors. This is shown by the calculation of CO2 cost of abatement curves. In this study it is demonstrated that the most effective technical measures with the lowest CO2 abatement costs yield solutions to the current energy problems. Various scenarios are presented concerning the question how the technological and environmental options for a sustainable energy system for Austria could look like in the long run. It is shown how sustainable energy can be supplied even with today-s technological knowledge and options available. The scenarios developed include an evaluation of the economic costs and ecological impacts. The results are not only applicable to Austria but demonstrate feasible and cost efficient ways towards a sustainable future.
Abstract: To achieve accurate and precise results of finite
element analysis (FEA) of bones, it is important to represent the
load/boundary conditions as identical as possible to the human body
such as the bone properties, the type and force of the muscles, the
contact force of the joints, and the location of the muscle attachment.
In this study, the difference in the Von-Mises stress and the total
deformation was compared by classifying them into Case 1, which
shows the actual anatomical form of the muscle attached to the femur
when the same muscle force was applied, and Case 2, which gives a
simplified representation of the attached location. An inverse
dynamical musculoskeletal model was simulated using data from an
actual walking experiment to complement the accuracy of the
muscular force, the input value of FEA. The FEA method using the
results of the muscular force that were calculated through the
simulation showed that the maximum Von-Mises stress and the
maximum total deformation in Case 2 were underestimated by 8.42%
and 6.29%, respectively, compared to Case 1. The torsion energy and
bending moment at each location of the femur occurred via the stress
ingredient. Due to the geometrical/morphological feature of the femur
of having a long bone shape when the stress distribution is wide, as
shown in Case 1, a greater Von-Mises stress and total deformation are
expected from the sum of the stress ingredients. More accurate results
can be achieved only when the muscular strength and the attachment
location in the FEA of the bones and the attachment form are the same
as those in the actual anatomical condition under the various moving
conditions of the human body.
Abstract: Wireless sensor networks (WSNs) have gained
tremendous attention in recent years due to their numerous
applications. Due to the limited energy resource, energy efficient
operation of sensor nodes is a key issue in wireless sensor networks.
Cooperative caching which ensures sharing of data among various
nodes reduces the number of communications over the wireless
channels and thus enhances the overall lifetime of a wireless sensor
network. In this paper, we propose a cooperative caching scheme
called ZCS (Zone Cooperation at Sensors) for wireless sensor
networks. In ZCS scheme, one-hop neighbors of a sensor node form a
cooperative cache zone and share the cached data with each other.
Simulation experiments show that the ZCS caching scheme achieves
significant improvements in byte hit ratio and average query latency
in comparison with other caching strategies.
Abstract: Linear stochastic estimation and quadratic stochastic
estimation techniques were applied to estimate the entire velocity
flow-field of an open cavity with a length to depth ratio of 2. The
estimations were done through the use of instantaneous velocity
magnitude as estimators. These measurements were obtained by
Particle Image Velocimetry. The predicted flow was compared
against the original flow-field in terms of the Reynolds stresses and
turbulent kinetic energy. Quadratic stochastic estimation proved to be
more superior than linear stochastic estimation in resolving the shear
layer flow. When the velocity fluctuations were scaled up in the
quadratic estimate, both the time-averaged quantities and the
instantaneous cavity flow can be predicted to a rather accurate extent.
Abstract: This paper presents development of an ignition system using spark electrodes for application in a research explosion vessel.
A single spark is aimed to be discharged with quantifiable ignition energy. The spark electrode system would enable study of flame
propagation, ignitability of fuel-air mixtures and other fundamental characteristics of flames. The principle of the capacitive spark circuit
of ASTM is studied to charge an appropriate capacitance connected across the spark gap through a large resistor by a high voltage from
the source of power supply until the initiation of spark. Different spark energies could be obtained mainly by varying the value of the
capacitance and the supply current. The spark sizes produced are found to be affected by the spark gap, electrode size, input voltage
and capacitance value.
Abstract: A boundary layer wind tunnel facility has been
adopted in order to conduct experimental measurements of the flow field around a model of the Panorama Giustinelli Building, Trieste
(Italy). Information on the main flow structures has been obtained by means of flow visualization techniques and has been compared to the
numerical predictions of the vortical structures spread on top of the roof, in order to investigate the optimal positioning for a vertical-axis
wind energy conversion system, registering a good agreement between experimental measurements and numerical predictions.
Abstract: Many methods exist for either measuring or estimating
evaporation from free water surfaces. Evaporation pans provide one
of the simplest, inexpensive, and most widely used methods of
estimating evaporative losses. In this study, the rate of evaporation
starting from a water surface was calculated by modeling with
application to dams in wet, arid and semi arid areas in Algeria.
We calculate the evaporation rate from the pan using the energy
budget equation, which offers the advantage of an ease of use, but
our results do not agree completely with the measurements taken by
the National Agency of areas carried out using dams located in areas
of different climates. For that, we develop a mathematical model to
simulate evaporation. This simulation uses an energy budget on the
level of a vat of measurement and a Computational Fluid Dynamics
(Fluent). Our calculation of evaporation rate is compared then by the
two methods and with the measures of areas in situ.
Abstract: Hydrogen is considered to be the most promising
candidate as a future energy carrier. One of the most used
technologies for the electrolytic hydrogen production is alkaline
water electrolysis. However, due to the high energy requirements, the
cost of hydrogen produced in such a way is high. In continuous
search to improve this process using advanced electrocatalytic
materials for the hydrogen evolution reaction (HER), Ni type Raney
and macro-porous Ni-Co electrodes were prepared on AISI 304
stainless steel substrates by electrodeposition. The developed
electrodes were characterized by SEM and confocal laser scanning
microscopy. HER on these electrodes was evaluated in 30 wt.% KOH
solution by means of hydrogen discharge curves and galvanostatic
tests. Results show that the developed electrodes present a most
efficient behaviour for HER when comparing with the smooth Ni
cathode. It has been reported a reduction in the energy consumption
of the electrolysis cell of about 25% by using the developed coatings
as cathodes.
Abstract: Shear walls are used in most of the tall buildings for
carrying the lateral load. When openings for doors or windows are
necessary to be existed in the shear walls, a special type of the shear
walls is used called "coupled shear walls" which in some cases is
stiffened by specific beams and so, called "stiffened coupled shear
walls".
In this paper, a mathematical method for geometrically nonlinear
analysis of the stiffened coupled shear walls has been presented.
Then, a suitable formulation for determining the critical load of the
stiffened coupled shear walls under gravity force has been proposed.
The governing differential equations for equilibrium and deformation
of the stiffened coupled shear walls have been obtained by setting up
the equilibrium equations and the moment-curvature relationships for
each wall. Because of the complexity of the differential equation, the
energy method has been adopted for approximate solution of the
equations.
Abstract: The stilling basins are commonly used to dissipate the
energy and protect the downstream floor from erosion. The aim of
the present experimental work is to improve the roughened stilling
basin using T-shape roughness instead of the regular cubic one and
design this new shape. As a result of the present work the best
intensity and the best roughness length are identified. Also, it is
found that the T-shape roughness save materials and reduce the jump
length compared to the cubic one. Sensitivity analysis was performed
and it was noticed that the change in the length of jump is more
sensitive to the change in roughness length than the change in
intensity.