Abstract: The current study has investigated the ageing
phenomena of silica optical fibres in relation to water activity which might be accelerated when exposed to a supplementary energy, such as microwaves. A controlled stress by winding fibres onto accurate
diameter mandrel was applied. Taking into account that normally a
decrease in fibre strength is induced in time by chemical action of water, the effects of cumulative reagents such as: water, applied stress and supplementary energy (microwave) in some cases acted in
the opposite manner. The microwave effect as a structural relaxation
catalyst appears unexpected, even if the overall gain in fibre strength is not high, but the stress corrosion factor revealed significant
increase in certain simulation conditions.
Abstract: A greenhouse experiment was conducted to investigate the effects of different types of nutrients induced salinity on the growth, membrane permeability, nitrate reductase activity, proline content and macronutrient concentrations of tomato plants. The plants were subjected to six different treatments: 1 (control) containing basic solution, 2 basic solution+40mM of NaCl, 3 basic solution+40 mM of KNO3, 4 basic solution+20 mM of Ca(NO3)2.4H2O, 5 basic solution+20 mM of Mg(NO3)2.6H2O and 6 basic solution+20 mM of KNO3+5 mM of Ca(NO3)2.4H2O+5 mM of Mg(NO3)2.6H2O. Membrane permeability was increased significantly only with addition of NaCl, and then decreased to its lower level with addition of Ca(NO3)2.4H2O and Mg(NO3)2.6H2O. Proline accumulation were followed the same trend of results when they had been exposed to NaCl salinity. Nitrate reductase activity (NRA) was significantly affected by addition of different types of nutrient induced salinity.
Abstract: An efficient transient flow simulation for gas
pipelines and networks is presented. The proposed transient flow
simulation is based on the transfer function models and MATLABSimulink.
The equivalent transfer functions of the nonlinear
governing equations are derived for different types of the boundary
conditions. Next, a MATLAB-Simulink library is developed and
proposed considering any boundary condition type. To verify the
accuracy and the computational efficiency of the proposed
simulation, the results obtained are compared with those of the
conventional finite difference schemes (such as TVD, method of
lines, and other finite difference implicit and explicit schemes). The
effects of the flow inertia and the pipeline inclination are
incorporated in this simulation. It is shown that the proposed
simulation has a sufficient accuracy and it is computationally more
efficient than the other methods.
Abstract: A reliable estimate of the average bond stress within
the anchorage of steel reinforcing bars in tension is critically
important for the design of reinforced concrete member. This paper
describes part of a recently completed experimental research program
in the Centre for Infrastructure Engineering and Safety (CIES) at the
University of New South Wales, Sydney, Australia aimed at
assessing the effects of different factors on the anchorage
requirements of modern high strength steel reinforcing bars. The
study found that an increase in the anchorage length and bar diameter
generally leads to a reduction of the average ultimate bond stress. By
the extension of a well established analytical model of bond and
anchorage, it is shown here that the differences in the average
ultimate bond stress for different anchorage lengths is associated with
the variable degree of plastic deformation in the tensile zone of the
concrete surrounding the bar.
Abstract: This study examined the effects of two dynamic
visualizations on 60 Malaysian primary school student-s performance
(time on task), retention and transference. The independent variables
in this study were the two dynamic visualizations, the video and the
animated instructions. The dependent variables were the gain score of
performance, retention and transference. The results showed that the
students in the animation group significantly outperformed the
students in the video group in retention. There were no significant
differences in terms of gain scores in the performance and
transference among the animation and the video groups, although the
scores were slightly higher in the animation group compared to the
video group. The conclusion of this study is that the animation
visualization is superior compared to the video in the retention for a
procedural task.
Abstract: Effects of bio-nitrogen fertilizer (bio-N), as a partial
alternative to mineral-nitrogen fertilizer (mineral-N), on growth,
yield and yield quality of broccoli plants were investigated. Bio-N
was applied at 1, 2 or 3 doses in combination with 65% of the
recommended dose of mineral-N (bio-N1, bio-N2 or bio-N3 +
⅔mineral-N). However, 100% of the recommended dose of mineral-
N was applied as a control. Significant positive influences of the bio-
N3 + ⅔mineral-N treatment were observed on growth traits, leaf
contents of nitrogen, phosphorus, potassium, nitrate and nitrite, and
yield quality when compared to the other two combined treatments.
In contrast, there were no significant differences in these parameters
between the bio-N3 + ⅔mineral-N and the control treatments, except
for leaf contents of nitrate and nitrite. They showed lower contents in
the bio-N3 + ⅔mineral-N treatment than the control. Therefore, we
recommend using bio-N as a partial alternative to mineral-N for
healthy nutrition.
Abstract: Repeated observation of a given area over time yields
potential for many forms of change detection analysis. These
repeated observations are confounded in terms of radiometric
consistency due to changes in sensor calibration over time,
differences in illumination, observation angles and variation in
atmospheric effects.
This paper demonstrates applicability of an empirical relative
radiometric normalization method to a set of multitemporal cloudy
images acquired by Resourcesat1 LISS III sensor. Objective of this
study is to detect and remove cloud cover and normalize an image
radiometrically. Cloud detection is achieved by using Average
Brightness Threshold (ABT) algorithm. The detected cloud is
removed and replaced with data from another images of the same
area. After cloud removal, the proposed normalization method is
applied to reduce the radiometric influence caused by non surface
factors. This process identifies landscape elements whose reflectance
values are nearly constant over time, i.e. the subset of non-changing
pixels are identified using frequency based correlation technique. The
quality of radiometric normalization is statistically assessed by R2
value and mean square error (MSE) between each pair of analogous
band.
Abstract: The potential of economically cheaper cellulose
containing natural materials like rice husk was assessed for nickel
adsorption from aqueous solutions. The effects of pH, contact time,
sorbent dose, initial metal ion concentration and temperature on the
uptake of nickel were studied in batch process. The removal of nickel
was dependent on the physico-chemical characteristics of the
adsorbent, adsorbate concentration and other studied process
parameters. The sorption data has been correlated with Langmuir,
Freundlich and Dubinin-Radush kevich (D-R) adsorption models. It
was found that Freundlich and Langmuir isotherms fitted well to the
data. Maximum nickel removal was observed at pH 6.0. The
efficiency of rice husk for nickel removal was 51.8% for dilute
solutions at 20 g L-1 adsorbent dose. FTIR, SEM and EDAX were
recorded before and after adsorption to explore the number and
position of the functional groups available for nickel binding on to
the studied adsorbent and changes in surface morphology and
elemental constitution of the adsorbent. Pseudo-second order model
explains the nickel kinetics more effectively. Reusability of the
adsorbent was examined by desorption in which HCl eluted 78.93%
nickel. The results revealed that nickel is considerably adsorbed on
rice husk and it could be and economic method for the removal of
nickel from aqueous solutions.
Abstract: Since polymerase chain reaction (PCR) has been
invented, it has emerged as a powerful tool in genetic analysis. The
PCR products are closely linked with thermal cycles. Therefore, to
reduce the reaction time and make temperature distribution uniform in
the reaction chamber, a novel oscillatory thermal cycler is designed.
The sample is placed in a fixed chamber, and three constant isothermal
zones are established and lined in the system. The sample is oscillated
and contacted with three different isothermal zones to complete
thermal cycles. This study presents the design of the geometric
characteristics of the chamber. The commercial software
CFD-ACE+TM is utilized to investigate the influences of various
materials, heating times, chamber volumes, and moving speed of the
chamber on the temperature distributions inside the chamber. The
chamber moves at a specific velocity and the boundary conditions
with time variations are related to the moving speed. Whereas the
chamber moves, the boundary is specified at the conditions of the
convection or the uniform temperature. The user subroutines compiled
by the FORTRAN language are used to make the numerical results
realistically. Results show that the reaction chamber with a rectangular
prism is heated on six faces; the effects of various moving speeds of
the chamber on the temperature distributions are examined. Regarding
to the temperature profiles and the standard deviation of the
temperature at the Y-cut cross section, the non-uniform temperature
inside chamber is found as the moving speed is larger than 0.01 m/s.
By reducing the heating faces to four, the standard deviation of the
temperature of the reaction chamber is under 1.4×10-3K with the range
of velocities between 0.0001 m/s and 1 m/s. The nature convective
boundary conditions are set at all boundaries while the chamber moves
between two heaters, the effects of various moving velocities of the
chamber on the temperature distributions are negligible at the assigned
time duration.
Abstract: The autonomic nervous system has a regulatory
structure that helps people adapt to changes in their environment by
adjusting or modifying some functions in response to stress, and regulating involuntary function of human organs. The purpose of this
study was to investigate the effect of combined stimulation, both
far-infrared heating and chiropractic, on the autonomic nervous system
activities using thermal image and heart rate variability. Six healthy subjects participated in this test. We compared the before and after
autonomic nervous system activities through obtaining thermal image
and photoplethysmogram signal. The thermal images showed that the
combined stimulation changed subject-s body temperature more
highly and widely than before. The result of heart rate variability
indicated that LF/HF ratio decreased. We concluded that combined
stimulation activates autonomic nervous system, and expected other
possibilities of this combined stimulation.
Abstract: Supplementation of palm vitamin E has been reported
to prevent loss of bone density in ovariectomised female rats. The
mechanism by which palm vitamin E exerts these effects is still
unknown. We hypothesized that palm vitamin E may act by
preventing the protein expression changes. Two dimensional poly
acyrilamide gel electrophoresis (2-D PAGE) and PD Quest software
genomic solutions Investigator (proteomics) was used to analyze the
differential protein expression profile in femoral and humeri bones
harvested from three groups of rats; sham-operated rats (SO),
ovariectomised rats (Ovx) and ovariectomised rats supplemented for
2 months with palm vitamin E. The results showed that there were
over 300 valued spot on each of the groups PVE and OVX as
compared to about 200 in SO. Comparison between the differential
protein expression between OVX and PVE groups showed that ten
spots were down –regulated in OVX but up-regulated in PVE. The
ten differential spots were separately named P1-P10. The
identification and understanding of the pathway of the differential
protein expression among the groups is ongoing and may account for
the molecular mechanism through which palm vitamin E exert its
anti-osteoporotic effect.
Abstract: Traffic enforcement units (the Police) are partly
responsible for the severity and frequency of the traffic accidents via
the effectiveness of their safety measures. The Police claims that the
reductions in accidents and their severities occur largely by their
timely interventions at the black spots, through traffic management
or temporary changes in the road design (guiding, reducing speeds
and eliminating sight obstructions, etc.). Yet, some other external
factors than the Police measures may intervene into which such
claims require a statistical confirmation. In order to test the net
impact of the Police contribution in the reduction of the number of
crashes, Chi square test was applied for 25 spots (streets and
intersections) and an average evaluation was achieved for general
conclusion in the case study of Izmir city. Separately, the net impact
of economic crisis in the reduction of crashes is assessed by the
trend analysis for the case of the economic crisis with the probable
reduction effects on the trip generation or modal choice. Finally, it
was proven that the Police measures were effective to some degree as
they claimed, though the economic crisis might have only negligible
contribution to the reductions in the same period observed.
Abstract: The results show that the bridge equipped with seismic isolation bearing system shows a high amount of energy dissipation. The purpose of the present study is to analyze the overall performance of continuous curved highway viaducts with different bearing supports, with an emphasis on the effectiveness of seismic isolation based on lead rubber bearing and hedge reaction force bearing system consisted of friction sliding bearing and rubber bearing. The bridge seismic performance has been evaluated on six different cases with six bearing models. The effects of the different arrangement of bearing on the deck superstructure displacements, the seismic damage at the bottom of the piers, movement track at the pier-s top and the total and strain energies absorbed by the structure are evaluated. In conclusion, the results provide sufficient evidence of the effectiveness on the use of seismic isolation on steel curved highway bridges.
Abstract: Presently and in line with the United Nations (EPA),
human thinking system has shifted towards clean fuels so as to
maintain a cleaner environment and to save our planet earth.
One of the most successful studies in order to achieve new
energies includes the use of animal wastes and their organic residues,
and the result of these researches has been represented in the form of
very simple and cheap methods called biogas technology. Biogas
technology has developed a lot in the recent decades; its reason is the
high cost of fossil fuels and the greater attention of countries to the
environmental pollutions due to the consumption of this kind of
fuels.
IRAN is ready for the optimized application of renewable
energies, having much enriched resources of this kind of energies; so
a special place could be considered for it when making programs.
The purpose of biogas technology is the recovery of energy and
finally the protection of the environment, which is much appropriate
for the third world farmers with respect to their technical abilities and
economic potentials. Studies show that the production and
consumption of biogas is appropriate and economic in IRAN,
because of the high amount of waste in the agriculture sector, the
significant amount of animal and human excrement production, the
great volume of garbage produced and the most important the
specific social, climatic and agricultural conditions in IRAN, in order
to proceed towards the reduction of pollution due to the use of fossil
fuels.
Abstract: Despite of the preponderant role played by cement among the construction materials, it is today considered as a material destructing the environment due to the large quantities of carbon dioxide exhausted during its manufacture. Besides, global warming is now recognized worldwide as the new threat to the humankind against which advanced countries are investigating measures to reduce the current amount of exhausted gases to the half by 2050. Accordingly, efforts to reduce green gases are exerted in all industrial fields. Especially, the cement industry strives to reduce the consumption of cement through the development of alkali-activated geopolymer mortars using industrial byproducts like bottom ash. This study intends to gather basic data on the flowability and strength development characteristics of alkali-activated geopolymer mortar by examining its FT-IT features with respect to the effects and strength of the alkali-activator in order to develop bottom ash-based alkali-activated geopolymer mortar. The results show that the 35:65 mass ratio of sodium hydroxide to sodium silicate is appropriate and that a molarity of 9M for sodium hydroxide is advantageous. The ratio of the alkali-activators to bottom ash is seen to have poor effect on the strength. Moreover, the FT-IR analysis reveals that larger improvement of the strength shifts the peak from 1060 cm–1 (T-O, T=Si or Al) toward shorter wavenumber.
Abstract: In this paper, we propose a selective mutation method
for improving the performances of genetic algorithms. In selective
mutation, individuals are first ranked and then additionally mutated
one bit in a part of their strings which is selected corresponding to
their ranks. This selective mutation helps genetic algorithms to fast
approach the global optimum and to quickly escape local optima.
This results in increasing the performances of genetic algorithms.
We measured the effects of selective mutation with four function
optimization problems. It was found from extensive experiments that
the selective mutation can significantly enhance the performances of
genetic algorithms.
Abstract: The influence of physical (external added weight) and
neurophysiological (fatigue) factors on static and dynamic balance in
sport related activities was typified statically by the Romberg test
(one foot flat, eyes open) and dynamically by jumping and hopping
in both horizontal and vertical directions. Twenty healthy males were
participated in this study. In Static condition, added weight increased
body-s inertia and therefore decreased body sway in AP direction
though not significantly. Dynamically, added weight significantly
increased body sway in both ML and AP directions, indicating
instability, and the use of the counter rotating segments mechanism to
maintain balance was demonstrated. Fatigue on the other hand
significantly increased body sway during static balance as a
neurophysiological adaptation primarily to the inverted pendulum
mechanism. Dynamically, fatigue significantly increased body sway
in both ML and AP directions again indicating instability but with a
greater use of counter rotating segments mechanism. Differential
adaptations for each of the two balance mechanisms (inverted
pendulum and counter rotating segments) were found between one
foot flat and two feet flat dynamic conditions, as participants relied
more heavily on the first in the one foot flat conditions and relied
more on the second in the two feet flat conditions.
Abstract: This paper presents a speed sensorless direct torque
control scheme using space vector modulation (DTC-SVM) for
permanent magnet synchronous motor (PMSM) drive based a Model
Reference Adaptive System (MRAS) algorithm and stator resistance
estimator. The MRAS is utilized to estimate speed and stator
resistance and compensate the effects of parameter variation on stator
resistance, which makes flux and torque estimation more accurate
and insensitive to parameter variation. In other hand the use of SVM
method reduces the torque ripple while achieving a good dynamic
response. Simulation results are presented and show the effectiveness
of the proposed method.
Abstract: The fabrication of porous NiTi shape memory alloys (SMAs) from elemental powder compacts was conducted by selfpropagating high temperature synthesis (SHS). Effects of the preheating temperature and the chamber pressure on the combustion characteristics as well as the final morphology and the composition of products were studied. The samples with porosity between 56.4 and 59.0% under preheating temperature in the range of 200-300°C and Ar-gas chamber pressure of 138 and 201 kPa were obtained. The pore structures were found to be dissimilar only in the samples processed with different preheating temperature. The major phase in the porous product is NiTi with small amounts of secondary phases, NiTi2 and Ni4Ti3. The preheating temperature and the chamber pressure have very little effect on the phase constituent. While the combustion temperature of the sample was notably increased by increasing the preheating temperature, they were slightly changed by varying the chamber pressure.
Abstract: Study of the vibration cylindrical shells made of
a functionally gradient material (FGM) composed of stainless
steel and nickel is important. Material properties are graded in
the thickness direction of the shell according to volume
fraction power law distribution. The objective is to study the
natural frequencies, the influence of constituent volume
fractions and the effects of boundary conditions on the natural
frequencies of the FG cylindrical shell. The study is carried
out using third order shear deformation shell theory. The
governing equations of motion of FG cylindrical shells are
derived based on shear deformation theory. Results are
presented on the frequency characteristics, influence of
constituent volume fractions and the effects of clampedclamped
boundary conditions.