Abstract: The boundary layer flow and heat transfer on a
stretched surface moving with prescribed skin friction is studied for
permeable surface. The surface temperature is assumed to vary
inversely with the vertical direction x for n = -1. The skin friction at
the surface scales as (x-1/2) at m = 0. The constants m and n are the
indices of the power law velocity and temperature exponent
respectively. Similarity solutions are obtained for the boundary layer
equations subject to power law temperature and velocity variation.
The effect of various governing parameters, such as the buoyancy
parameter λ and the suction/injection parameter fw for air (Pr = 0.72)
are studied. The choice of n and m ensures that the used similarity
solutions are x independent. The results show that, assisting flow (λ >
0) enhancing the heat transfer coefficient along the surface for any
constant value of fw. Furthermore, injection increases the heat
transfer coefficient but suction reduces it at constant λ.
Abstract: The paper presents an analytical solution for dispersion
of a solute in the peristaltic motion of a micropolar fluid in the
presence of magnetic field and both homogeneous and heterogeneous
chemical reactions. The average effective dispersion coefficient has
been found using Taylor-s limiting condition under long wavelength
approximation. The effects of various relevant parameters on the average
coefficient of dispersion have been studied. The average effective
dispersion coefficient increases with amplitude ratio, cross viscosity
coefficient and heterogeneous chemical reaction rate parameter. But it
decreases with magnetic field parameter and homogeneous chemical
reaction rate parameter. It can be noted that the presence of peristalsis
enhances dispersion of a solute.
Abstract: Cavitation in pumps is known as the formation of
vapor bubbles due to pressure drop and collapsing these bubbles. In
some conditions, it has been observed that the formation of bubbles
occurs at the pressure side of centrifugal pump blades. In this study,
the formation of bubbles at the pressure side of blades has been
investigated. Water is used in this study as the fluid and performance
curves were depicted for different flow rates in an approximately
constant speed. The results show that when a centrifugal pump works
in low flow rates, a secondary flow namely recirculation starts to
begin. In this condition, separation of flow increases which causes
vortex formation and local pressure drop and eventually the
formation of vapor bubbles starts.
Abstract: These Nowadays the explosion of bombs or explosive
materials such as gas and oil near or inside the buildings cause some
losses in installations and building components. This has made the
engineers to make the buildings and their components resistance
against the effects of explosion. These activities lead to provide
regulations and different methods. The above regulations are mostly
focused on the explosion effects resulting from the vehicles around
the buildings. Therefore, the explosion resulting from the vehicles
outside the buildings will be studied in this research.
In the present study, the main goals are to investigate the
explosion load effects on the structures located on the piles with the
specific quantity of plasticity and observing the permissible response
of these structures. The concentrated mass system and the spring with
two degree of freedom will be used to study the structural system.
Abstract: This paper presents design trade-off and performance impacts of
the amount of pipeline phase of control path signals in a wormhole-switched
network-on-chip (NoC). The numbers of the pipeline phase of the control
path vary between two- and one-cycle pipeline phase. The control paths
consist of the routing request paths for output selection and the arbitration
paths for input selection. Data communications between on-chip routers are
implemented synchronously and for quality of service, the inter-router data
transports are controlled by using a link-level congestion control to avoid
lose of data because of an overflow. The trade-off between the area (logic
cell area) and the performance (bandwidth gain) of two proposed NoC router
microarchitectures are presented in this paper. The performance evaluation is
made by using a traffic scenario with different number of workloads under
2D mesh NoC topology using a static routing algorithm. By using a 130-nm
CMOS standard-cell technology, our NoC routers can be clocked at 1 GHz,
resulting in a high speed network link and high router bandwidth capacity
of about 320 Gbit/s. Based on our experiments, the amount of control path
pipeline stages gives more significant impact on the NoC performance than
the impact on the logic area of the NoC router.
Abstract: This paper focuses on the Mega-Sub Controlled
Structure Systems (MSCSS) performances and characteristics
regarding the new control principle contained in MSCSS subjected to
strong earthquake excitations. The adopted control scheme consists of
modulated sub-structures where the control action is achieved by
viscous dampers and sub-structure own configuration. The
elastic-plastic time history analysis under severe earthquake excitation
is analyzed base on the Finite Element Analysis Method (FEAM), and
some comparison results are also given in this paper. The result shows
that the MSCSS systems can remarkably reduce vibrations effects
more than the mega-sub structure (MSS). The study illustrates that the
improved MSCSS presents good seismic resistance ability even at 1.2g
and can absorb seismic energy in the structure, thus imply that
structural members cross section can be reduce and achieve to good
economic characteristics. Furthermore, the elasto-plastic analysis
demonstrates that the MSCSS is accurate enough regarding
international building evaluation and design codes. This paper also
shows that the elasto-plastic dynamic analysis method is a reasonable
and reliable analysis method for structures subjected to strong
earthquake excitations and that the computed results are more precise.
Abstract: This study was designed to formulate,
pharmaceutically evaluate a topical skin-care cream (w/o emulsion)
of Aloe Vera versus its vehicle (Base) as control and determine their
effects on Stratum Corneum (SC) water content and Transepidermal
water loss (TEWL). Base containing no extract and a Formulation
containing 3% concentrated extract of Aloe Vera was developed by
entrapping in the inner aqueous phase of w/o emulsion (cream).
Lemon oil was incorporated to improve the odor. Both the Base and
Formulation were stored at 8°C ±0.1°C (in refrigerator), 25°C±0.1°C,
40°C±0.1°C and 40°C± 0.1°C with 75% RH (in incubator) for a
period of 4 weeks to predict their stability. The evaluation parameters
consisted of color, smell, type of emulsion, phase separation,
electrical conductivity, centrifugation, liquefaction and pH. Both the
Base and Formulation were applied to the cheeks of 21 healthy
human volunteers for a period of 8 weeks Stratum corneum (SC)
water content and Transepidermal water loss (TEWL) were
monitored every week to measure any effect produced by these
topical creams. The expected organoleptic stability of creams was
achieved from 4 weeks in-vitro study period. Odor was disappeared
with the passage of time due to volatilization of lemon oil. Both the
Base and Formulation produced significant (p≤0.05) changes in
TEWL with respect to time. SC water content was significantly
(p≤0.05) increased by the Formulation while the Base has
insignificant (p 0.05) effects on SC water content. The newly
formulated cream of Aloe Vera, applied is suitable for improvement
and quantitative monitoring of skin hydration level (SC water
content/ moisturizing effects) and reducing TEWL in people with dry
skin.
Abstract: The environment pollution with pesticides and heavy
metals is a recognized problem nowadays, with extension to the
global scale the tendency of amplification. Even with all the progress
in the environmental field, both in the emphasize of the effect of the
pollutants upon health, the linked studies environment-health are
insufficient, not only in Romania but all over the world also. We aim
to describe the particular situation in Romania regarding the
uncontrolled use of pesticides, to identify and evaluate the risk zones
for health and the environment in Romania, with the final goal of
designing adequate programs for reduction and control of the risk
sources. An exploratory study was conducted to determine the
magnitude of the pesticide use problem in a population living in
Saliste, a rural setting in Transylvania, Romania. The significant
stakeholders in Saliste region were interviewed and a sample from
the population living in Saliste area was selected to fill in a designed
questionnaire. All the selected participants declared that they used
pesticides in their activities for more than one purpose. They
declared they annually applied pesticides for a period of time
between 11 and 30 years, from 5 to 9 days per year on average,
mainly on crops situated at some distance from the houses but high
risk behavior was identified as the volunteers declared the use of
pesticides in the backyard gardens, near their homes, where children
were playing. The pesticide applicators did not have the necessary
knowledge about safety and exposure. The health data must be
correlated with exposure biomarkers in attempt to identify the
possible health effects of the pesticides exposure. Future plans
include educational campaigns to raise the awareness of the
population on the danger of uncontrolled use of pesticides.
Abstract: Existing ground movement surveillance technologies
at airports are subjected to limitations due to shadowing effects or
multiple reflections. Therefore, there is a strong demand for a new
sensing technology, which will be cost effective and will provide
detection of non-cooperative targets under any weather conditions.
This paper aims to present a new intelligent system, developed
within the framework of the EC-funded ISMAEL project, which is
based on a new magnetic sensing technology and provides detection,
tracking and automatic classification of targets moving on the airport
surface. The system is currently being installed at two European
airports. Initial experimental results under real airport traffic
demonstrate the great potential of the proposed system.
Abstract: Hydroxymethylfurfural (HMF) is formed by thermally
treating products rich in carbohydrates. HMF and other furan
derivatives are toxic.
The aim of the research was to establish the content of HMF in
gingerbread biscuits with honey and sugar syrup additives by using
three leavening agents— ammonium carbonate (NH4HCO3 and
(NH4)2CO3), baking powder, and baking soda (NaHCO3).
The content of HMF is significantly affected by the leavening
agent used. The content of HMF with honey where ammonium
carbonate was used as additive range from 5.7 to 27.3mg 100g-1, but
when sugar syrup is used the content varies from 2.3 to 7.4mg 100g-1.
When baking powder and baking soda are used as leavening agents,
the content of HMF exceeds 4mg 100g-1 in the event honey had been
added and the baking time had been longer (10 minutes at 180°C or
9 minutes at 200°C).
Abstract: To investigates the effect of fiberglass clamping
process improvement on drape simulation prediction. This has
great effect on the mould and the fiber during manufacturing
process. This also, improves the fiber strain, the quality of the
fiber orientation in the area of folding and wrinkles formation
during the press-forming process. Drape simulation software
tool was used to digitalize the process, noting the formation
problems on the contour sensitive part. This was compared
with the real life clamping processes using single and double
frame set-ups to observe the effects. Also, restrains are
introduced by using clips, and the G-clamps with predetermine
revolution to; restrain the fabric deformation during the
forming process.The incorporation of clamping and fabric
restrain deformation improved on the prediction of the
simulation tool. Therefore, for effective forming process,
incorporation of clamping process into the drape simulation
process will assist in the development of fiberglass application
in manufacturing process.
Abstract: This paper presents the results of enhancing images from a left and right stereo pair in order to increase the resolution of a 3D representation of a scene generated from that same pair. A new neural network structure known as a Self Delaying Dynamic Network (SDN) has been used to perform the enhancement. The advantage of SDNs over existing techniques such as bicubic interpolation is their ability to cope with motion and noise effects. SDNs are used to generate two high resolution images, one based on frames taken from the left view of the subject, and one based on the frames from the right. This new high resolution stereo pair is then processed by a disparity map generator. The disparity map generated is compared to two other disparity maps generated from the same scene. The first is a map generated from an original high resolution stereo pair and the second is a map generated using a stereo pair which has been enhanced using bicubic interpolation. The maps generated using the SDN enhanced pairs match more closely the target maps. The addition of extra noise into the input images is less problematic for the SDN system which is still able to out perform bicubic interpolation.
Abstract: This work focuses on the remediation of polycyclic
aromatic hydrocarbons (PAHs)-contaminated soil via Fenton
treatment coupled with novel chelating agent (CA). The feasibility of
chelated modified Fenton (MF) treatment to promote PAH oxidation
in artificially contaminated soils was investigated in laboratory scale
batch experiments at natural pH. The effects of adding inorganic and
organic CA are discussed. Experiments using different iron catalyst
to CA ratios were conducted, resulting in hydrogen peroxide: soil:
iron: CA weight ratios that varied from 0.049: 1: 0.072: 0.008 to
0.049: 1: 0.072: 0.067. The results revealed that (1) inorganic CA
could provide much higher PAH removal efficiency and (2) most of
the proposed CAs were more efficient than commonly utilised CAs
even at mild ratio. This work highlights the potential of novel
chelating agents in maintaining a suitable environment throughout
the Fenton treatment, particularly in soils with high buffer capacity.
Abstract: The characterization of κ-carrageenan could provide a
better understanding of its functions in biological, medical and
industrial applications. Chemical and physical analyses of
carrageenan from seaweeds, Euchema cottonii L., were done to offer
information on its properties and the effects of Co-60 γ-irradiation on
its thermochemical characteristics. The structural and morphological
characteristics of κ-carrageenan were determined using scanning
electron microscopy (SEM) while the composition, molecular weight
and thermal properties were determined using attenuated total
reflectance Fourier transform infrared spectroscopy (ATR-FTIR), gel
permeation chromatography (GPC), thermal gravimetric analysis
(TGA) and differential scanning calorimetry (DSC). Further chemical
analysis was done using hydrogen-1 nuclear magnetic resonance (1H
NMR) and functional characteristics in terms of biocompatibility
were evaluated using cytotoxicity test.
Abstract: As the Computed Tomography(CT) requires normally
hundreds of projections to reconstruct the image, patients are exposed
to more X-ray energy, which may cause side effects such as cancer.
Even when the variability of the particles in the object is very less,
Computed Tomography requires many projections for good quality
reconstruction. In this paper, less variability of the particles in an
object has been exploited to obtain good quality reconstruction.
Though the reconstructed image and the original image have same
projections, in general, they need not be the same. In addition
to projections, if a priori information about the image is known,
it is possible to obtain good quality reconstructed image. In this
paper, it has been shown by experimental results why conventional
algorithms fail to reconstruct from a few projections, and an efficient
polynomial time algorithm has been given to reconstruct a bi-level
image from its projections along row and column, and a known sub
image of unknown image with smoothness constraints by reducing the
reconstruction problem to integral max flow problem. This paper also
discusses the necessary and sufficient conditions for uniqueness and
extension of 2D-bi-level image reconstruction to 3D-bi-level image
reconstruction.
Abstract: Environment both endowed and built are essential for
tourism. However tourism and environment maintains a complex
relationship, where in most cases environment is at the receiving end.
Many tourism development activities have adverse environmental
effects, mainly emanating from construction of general infrastructure
and tourism facilities. These negative impacts of tourism can lead to
the destruction of precious natural resources on which it depends.
These effects vary between locations; and its effect on a hill
destination is highly critical. This study aims at developing a
Sustainable Tourism Planning Model for an environmentally
sensitive tourism destination in Kerala, India. Being part of the
Nilgiri mountain ranges, Munnar falls in the Western Ghats, one of
the biological hotspots in the world. Endowed with a unique high
altitude environment Munnar inherits highly significant ecological
wealth. Giving prime importance to the protection of this ecological
heritage, the study proposes a tourism planning model with resource
conservation and sustainability as the paramount focus. Conceiving a
novel approach towards sustainable tourism planning, the study
proposes to assess tourism attractions using Ecological Sensitivity
Index (ESI) and Tourism Attractiveness Index (TAI). Integration of
these two indices will form the Ecology – Tourism Matrix (ETM),
outlining the base for tourism planning in an environmentally
sensitive destination. The ETM Matrix leads to a classification of
tourism nodes according to its Conservation Significance and
Tourism Significance. The spatial integration of such nodes based on
the Hub & Spoke Principle constitutes sub – regions within the STZ.
Ensuing analyses lead to specific guidelines for the STZ as a whole,
specific tourism nodes, hubs and sub-regions. The study results in a
multi – dimensional output, viz., (1) Classification system for tourism
nodes in an environmentally sensitive region/ destination (2)
Conservation / Tourism Development Strategies and Guidelines for
the micro and macro regions and (3) A Sustainable Tourism Planning
Tool particularly for Ecologically Sensitive Destinations, which can
be adapted for other destinations as well.
Abstract: This paper presents a genetic algorithm based
approach for solving security constrained optimal power flow
problem (SCOPF) including FACTS devices. The optimal location of
FACTS devices are identified using an index called overload index
and the optimal values are obtained using an enhanced genetic
algorithm. The optimal allocation by the proposed method optimizes
the investment, taking into account its effects on security in terms of
the alleviation of line overloads. The proposed approach has been
tested on IEEE-30 bus system to show the effectiveness of the
proposed algorithm for solving the SCOPF problem.
Abstract: This is a study on numerical simulation of the convection-diffusion transport of a chemical species in steady flow through a small-diameter tube, which is lined with a very thin layer made up of retentive and absorptive materials. The species may be subject to a first-order kinetic reversible phase exchange with the wall material and irreversible absorption into the tube wall. Owing to the velocity shear across the tube section, the chemical species may spread out axially along the tube at a rate much larger than that given by the molecular diffusion; this process is known as dispersion. While the long-time dispersion behavior, well described by the Taylor model, has been extensively studied in the literature, the early development of the dispersion process is by contrast much less investigated. By early development, that means a span of time, after the release of the chemical into the flow, that is shorter than or comparable to the diffusion time scale across the tube section. To understand the early development of the dispersion, the governing equations along with the reactive boundary conditions are solved numerically using the Flux Corrected Transport Algorithm (FCTA). The computation has enabled us to investigate the combined effects on the early development of the dispersion coefficient due to the reversible and irreversible wall reactions. One of the results is shown that the dispersion coefficient may approach its steady-state limit in a short time under the following conditions: (i) a high value of Damkohler number (say Da ≥ 10); (ii) a small but non-zero value of absorption rate (say Γ* ≤ 0.5).
Abstract: Computed tomography and laminography are heavily investigated in a compressive sensing based image reconstruction framework to reduce the dose to the patients as well as to the radiosensitive devices such as multilayer microelectronic circuit boards. Nowadays researchers are actively working on optimizing the compressive sensing based iterative image reconstruction algorithm to obtain better quality images. However, the effects of the sampled data’s properties on reconstructed the image’s quality, particularly in an insufficient sampled data conditions have not been explored in computed laminography. In this paper, we investigated the effects of two data properties i.e. sampling density and data incoherence on the reconstructed image obtained by conventional computed laminography and a recently proposed method called spherical sinusoidal scanning scheme. We have found that in a compressive sensing based image reconstruction framework, the image quality mainly depends upon the data incoherence when the data is uniformly sampled.
Abstract: Tanzania is a developing country, which significantly lags behind the rest of the world in information communications technology (ICT), especially for the Internet. Internet connectivity to the rest of the world is via expensive satellite links, thus leaving the majority of the population unable to access the Internet due to the high cost. This paper introduces the concept of an optical WDM network for Internet infrastructure in Tanzania, so as to reduce Internet connection costs, and provide Internet access to the majority of people who live in both urban and rural areas. We also present a proposed optical WDM network, which mitigates the effects of system impairments, and provide simulation results to show that the data is successfully transmitted over a longer distance using a WDM network.