Abstract: In the present study, changes of morphology and
mechanical characteristics in the lumbar vertebrae of the
ovariectomised (OVX) rat were investigated. In previous researches,
there were many studies about morphology like volume fraction and
trabecular thickness based on Micro - Computed Tomography (Micro
- CT). However, detecting and tracking long-term changes in the
trabecular bone of the lumbar vertebrae for the OVX rat were few. For
this study, one female Sprague-Dawley rat was used: an OVX rat. The
4th Lumbar of the OVX rat was subjected to in-vivo micro-CT.
Detecting and tracking long-term changes could be investigated in the
trabecular bone of the lumbar vertebrae for an OVX rat using in-vivo
micro-CT. An OVX rat was scanned at week 0 (just before surgery), at
week 4, at week 8, week 16, week 22 and week 56 after surgery. Finite
element (FE) analysis was used to investigate mechanical
characteristics of the lumbar vertebrae for an OVX rat. When the OVX
rat (at week 56) was compared with the OVX rat (at week 0), volume
fraction was decreased by 80% and effective modulus was decreased
by 75%.
Abstract: An experimental and numerical study has been conducted to clarify heat transfer characteristics and effectiveness of a cross-flow heat exchanger employing staggered wing-shaped tubes at different angels of attack. The water-side Rew and the air-side Rea were at 5 x 102 and at from 1.8 x 103 to 9.7 x 103, respectively. The tubes arrangements were employed with various angles of attack θ1,2,3 from 0° to 330° at the considered Rea range. Correlation of Nu, St, as well as the heat transfer per unit pumping power (ε) in terms of Rea, design parameters for the studied bundle were presented. The temperature fields around the staggered wing-shaped tubes bundle were predicted by using commercial CFD FLUENT 6.3.26 software package. Results indicated that the heat transfer was increased by increasing the angle of attack from 0° to 45°, while the opposite was true for angles of attack from 135° to 180°. The best thermal performance and hence η of studied bundle was occurred at the lowest Rea and/or zero angle of attack. Comparisons between the experimental and numerical results of the present study and those, previously, obtained for similar available studies showed good agreements.
Abstract: The hospital and the health-care center of a
community, as a place for people-s life-care and health-care settings,
must provide more and better services for patients or residents. After
Establishing Electronic Medical Record (EMR) system -which is a
necessity- in the hospital, providing pervasive services is a further
step. Our objective in this paper is to use pervasive computing in a
case study of healthcare, based on EMR database that coordinates
application services over network to form a service environment for
medical and health-care. Our method also categorizes the hospital
spaces into 3 spaces: Public spaces, Private spaces and Isolated
spaces. Although, there are many projects about using pervasive
computing in healthcare, but all of them concentrate on the disease
recognition, designing smart cloths, or provide services only for
patient. The proposed method is implemented in a hospital. The
obtained results show that it is suitable for our purpose.
Abstract: This paper describes studies carried out to investigate
the viability of using wireless cameras as a tool in monitoring
changes in air quality. A camera is used to monitor the change in
colour of a chemically responsive polymer within view of the camera
as it is exposed to varying chemical species concentration levels. The
camera captures this image and the colour change is analyzed by
averaging the RGB values present. This novel chemical sensing
approach is compared with an established chemical sensing method
using the same chemically responsive polymer coated onto LEDs. In
this way, the concentration levels of acetic acid in the air can be
tracked using both approaches. These approaches to chemical plume
tracking have many applications for air quality monitoring.
Abstract: ZnO heteronanostructured nanowires arrays have
been fabricated by low temperature solution method. Various
heterostructures were synthesized including CdS/ZnO,
CdSe/CdS/ZnO nanowires and Co3O4/ZnO, ZnO/SiC
nanowires. These multifunctional heterostructure nanowires
showed important applications in photocatalysts, sensors,
wettability control and solar energy conversion.
Abstract: An enhanced particle swarm optimization algorithm
(PSO) is presented in this work to solve the non-convex OPF
problem that has both discrete and continuous optimization variables.
The objective functions considered are the conventional quadratic
function and the augmented quadratic function. The latter model
presents non-differentiable and non-convex regions that challenge
most gradient-based optimization algorithms. The optimization
variables to be optimized are the generator real power outputs and
voltage magnitudes, discrete transformer tap settings, and discrete
reactive power injections due to capacitor banks. The set of equality
constraints taken into account are the power flow equations while the
inequality ones are the limits of the real and reactive power of the
generators, voltage magnitude at each bus, transformer tap settings,
and capacitor banks reactive power injections. The proposed
algorithm combines PSO with Newton-Raphson algorithm to
minimize the fuel cost function. The IEEE 30-bus system with six
generating units is used to test the proposed algorithm. Several cases
were investigated to test and validate the consistency of detecting
optimal or near optimal solution for each objective. Results are
compared to solutions obtained using sequential quadratic
programming and Genetic Algorithms.
Abstract: Development of artificial neural network (ANN) for
prediction of aluminum workpieces' surface roughness in ultrasonicvibration
assisted turning (UAT) has been the subject of the present
study. Tool wear as the main cause of surface roughness was also
investigated. ANN was trained through experimental data obtained
on the basis of full factorial design of experiments. Various
influential machining parameters were taken into consideration. It
was illustrated that a multilayer perceptron neural network could
efficiently model the surface roughness as the response of the
network, with an error less than ten percent. The performance of the
trained network was verified by further experiments. The results of
UAT were compared with the results of conventional turning
experiments carried out with similar machining parameters except for
the vibration amplitude whence considerable reduction was observed
in the built-up edge and the surface roughness.
Abstract: A reduced-bit multiplication algorithm based on the ancient Vedic multiplication formulae is proposed in this paper. Both the Vedic multiplication formulae, Urdhva tiryakbhyam and Nikhilam, are first discussed in detail. Urdhva tiryakbhyam, being a general multiplication formula, is equally applicable to all cases of multiplication. It is applied to the digital arithmetic and is shown to yield a multiplier architecture which is very similar to the popular array multiplier. Due to its structure, it leads to a high carry propagation delay in case of multiplication of large numbers. Nikhilam Sutra, on the other hand, is more efficient in the multiplication of large numbers as it reduces the multiplication of two large numbers to that of two smaller numbers. The framework of the proposed algorithm is taken from this Sutra and is further optimized by use of some general arithmetic operations such as expansion and bit-shifting to take advantage of bit-reduction in multiplication. We illustrate the proposed algorithm by reducing a general 4x4-bit multiplication to a single 2 x 2-bit multiplication operation.
Abstract: In this paper, a method for deriving a group priority vector in the Fuzzy Analytic Network Process (FANP) is proposed. By introducing importance weights of multiple decision makers (DMs) based on their experiences, the Fuzzy Preferences Programming Method (FPP) is extended to a fuzzy group prioritization problem in the FANP. Additionally, fuzzy pair-wise comparison judgments are presented rather than exact numerical assessments in order to model the uncertainty and imprecision in the DMs- judgments and then transform the fuzzy group prioritization problem into a fuzzy non-linear programming optimization problem which maximize the group satisfaction. Unlike the known fuzzy prioritization techniques, the new method proposed in this paper can easily derive crisp weights from incomplete and inconsistency fuzzy set of comparison judgments and does not require additional aggregation producers. Detailed numerical examples are used to illustrate the implement of our approach and compare with the latest fuzzy prioritization method.
Abstract: The development of sustainable utilization water resources is crucial. The ecological environment and water resources systems form the foundation of the existence and development of the social economy. The urban ecological support system depends on these resources as well. This research studies the vulnerability, criticality, and risk of climate change on water supply and demand in the main administrative district of the Taijiang Area (Tainan City). Based on the two situations set in this paper and various factors (indexes), this research adopts two kinds of weights (equal and AHP) to conduct the calculation and establish the water supply and demand risk map for the target year 2039. According to the risk analysis result, which is based on equal weight, only one district belongs to a high-grade district (Grade 4). Based on the AHP weight, 16 districts belong to a high-grade or higher-grade district (Grades 4 and 5), and from among them, two districts belong to the highest grade (Grade 5). These results show that the risk level of water supply and demand in cities is higher than that in towns. The government generally gives more attention to the adjustment strategy in the “cities." However, it should also provide proper adjustment strategies for the “towns" to be able to cope with the risks of water supply and demand.
Abstract: There is increasing pressure on, and decline of
mopane woodlands due to increasing use and competition for
mopane resources in Zimbabwe in Namibia. Community management strategies, based largely on local knowledge are
evidently unable to cope. Research has generated potentially useful
information for mopane woodland management, but this information
has not been utilized. The work reported in this paper sought to add value to research work conducted on mopane woodlands by
developing effective community-based mopane woodland
management regimes that were based on both local and scientific
knowledge in Zimbabwe and Namibia. The conditions under which research findings were likely to be adopted for mopane woodland management by communities were investigated. The study was conducted at two sites each in Matobo and Omusati Districts in Zimbabwe and Namibia respectively. The mopane woodland
resources in the two study areas were assessed using scientific
ecological methods. A range of participatory methods was used to collect information on use of mopane woodland resources by communities, institutional arrangements governing access to and use
of these resources and to evaluate scientific knowledge for
applicability in local management regimes. Coppicing, thinning and
pollarding were the research generated management methods evaluated. Realities such as availability of woodland resources and
social roles and responsibilities influenced preferences for woodland
management interventions
Abstract: There are very complex communication systems, as
the multifunction radar, MFAR (Multi-Function Array Radar), where
functions are integrated all together, and simultaneously are
performed the classic functions of tracking and surveillance, as all
the functions related to the communication, countermeasures, and
calibration. All these functions are divided into the tasks to execute.
The task scheduler is a key element of the radar, since it does the
planning and distribution of energy and time resources to be shared
and used by all tasks. This paper presents schedulers based on the use
of multiple queue. Several schedulers have been designed and
studied, and it has been made a comparative analysis of different
performed schedulers. The tests and experiments have been done by
means of system software simulation. Finally a suitable set of radar
characteristics has been selected to evaluate the behavior of the task
scheduler working.
Abstract: Encryption and decryption in RSA are done by modular exponentiation which is achieved by repeated modular multiplication. Hence efficiency of modular multiplication directly determines the efficiency of RSA cryptosystem. This paper designs a Modified Montgomery Modular Multiplication in which addition of operands is computed by 4:2 compressor. The basic logic operations in addition are partitioned over two iterations such that parallel computations are performed. This reduces the critical path delay of proposed Montgomery design. The proposed design and RSA are implemented on Virtex 2 and Virtex 5 FPGAs. The two factors partitioning and parallelism have improved the frequency and throughput of proposed design.
Abstract: The objective of this paper is to study the analysis and testing for determining the torsional stiffness of the student formula-s space frame. From past study, the space frame for Chulalongkorn University Student Formula team used in 2011 TSAE Auto Challenge Student Formula in Thailand was designed by considering required mass and torsional stiffness based on the numerical method and experimental method. The numerical result was compared with the experimental results to verify the torsional stiffness of the space frame. It can be seen from the large error of torsional stiffness of 2011 frame that the experimental result can not verify by the numerical analysis due to the different between the numerical model and experimental setting. In this paper, the numerical analysis and experiment of the same 2011 frame model is performed by improving the model setting. The improvement of both numerical analysis and experiment are discussed to confirm that the models from both methods are same. After the frame was analyzed and tested, the results are compared to verify the torsional stiffness of the frame. It can be concluded that the improved analysis and experiments can used to verify the torsional stiffness of the space frame.
Abstract: This paper presents a comparative study on two most
popular control strategies for Permanent Magnet Synchronous Motor
(PMSM) drives: field-oriented control (FOC) and direct torque
control (DTC). The comparison is based on various criteria including
basic control characteristics, dynamic performance, and
implementation complexity. The study is done by simulation using
the Simulink Power System Blockset that allows a complete
representation of the power section (inverter and PMSM) and the
control system. The simulation and evaluation of both control
strategies are performed using actual parameters of Permanent
Magnet Synchronous Motor fed by an IGBT PWM inverter.
Abstract: In this paper, we have examined the effect of process
parameter variation on the electrical characteristics of an LDMOS
device. The rate of change in the electrical parameters such as cut off
frequency, breakdown voltage and drain saturation current as a
function of the process parameters is investigated
Abstract: Time delay in bilateral teleoperation system was
introduced as a sufficient reason to make the system unstable or
certainly degrade the system performance. In this paper, simulations
and experimental results of implementing p-like control scheme,
under different ranges of variable time delay, will be presented to
verify a certain criteria, which guarantee the system stability and
position tracking. The system consists of two Phantom premium 1.5A
devices. One of them acts as a master and the other acts as a slave.
The study includes deriving the Phantom kinematic and dynamic
model, establishing the link between the two Phantoms over
Simulink in Matlab, and verifying the stability criteria with
simulations and real experiments.
Abstract: Variable speed drives are growing and varying. Drives expanse depend on progress in different part of science like power system, microelectronic, control methods, and so on. Artificial intelligent contains hard computation and soft computation. Artificial intelligent has found high application in most nonlinear systems same as motors drive. Because it has intelligence like human but there are no sentimental against human like angriness and.... Artificial intelligent is used for various points like approximation, control, and monitoring. Because artificial intelligent techniques can use as controller for any system without requirement to system mathematical model, it has been used in electrical drive control. With this manner, efficiency and reliability of drives increase and volume, weight and cost of them decrease.
Abstract: The present work is concerned with sulfidation of Cu,
Zn and Ni containing plating wastewater with CaS. The sulfidation
experiments were carried out at a room temperature by adding solid
CaS to simulated metal solution containing either single-metal of Ni,
Zn and Cu, or Ni-Zn-Cu mixture. At first, the experiments were
conducted without pH adjustment and it was found that the complete
sulfidation of Zn and Ni was achieved at an equimolar ratio of CaS to a
particular metal. However, in the case of Cu, a complete copper
sulfidation was achieved at CaS to Cu molar ratio of about 2. In the
case of the selective sulfidation, a simulated plating solution
containing Cu, Zn and Ni at the concentration of 100 mg/dm3 was
treated with CaS under various pH conditions. As a result, selective
precipitation of metal sulfides was achieved by a sulfidation treatment
at different pH values. Further, the precipitation agents of NaOH,
Na2S and CaS were compared in terms of the average specific
filtration resistance and compressibility coefficients of metal sulfide
slurry. Consequently, based on the lowest filtration parameters of the
produced metal sulfides, it was concluded that CaS was the most
effective precipitation agent for separation and recovery of Cu, Zn and
Ni.
Abstract: Today, numerical simulation is a powerful tool to
solve various hydraulic engineering problems. The aim of this
research is numerical solutions of shallow water equations using
finite volume method for Simulations of dam break over wet and dry
bed. In order to solve Riemann problem, Roe-s approximate solver is
used. To evaluate numerical model, simulation was done in 1D and
2D states. In 1D state, two dam break test over dry bed (with and
without friction) were studied. The results showed that Structural
failure around the dam and damage to the downstream constructions
in bed without friction is more than friction bed. In 2D state, two
tests for wet and dry beds were done. Generally in wet bed case,
waves are propagated to canal sides but in dry bed it is not
significant. Therefore, damage to the storage facilities and
agricultural lands in wet bed case is more than in dry bed.