Abstract: In this paper we proposed multistage adaptive
ARQ/HARQ/HARQ scheme. This method combines pure ARQ
(Automatic Repeat reQuest) mode in low channel bit error rate and
hybrid ARQ method using two different Reed-Solomon codes in
middle and high error rate conditions. It follows, that our scheme has
three stages. The main goal is to increase number of states in adaptive
HARQ methods and be able to achieve maximum throughput for
every channel bit error rate. We will prove the proposal by
calculation and then with simulations in land mobile satellite channel
environment. Optimization of scheme system parameters is described
in order to maximize the throughput in the whole defined Signal-to-
Noise Ratio (SNR) range in selected channel environment.
Abstract: Heat pipes are used to control the thermal problem for
electronic cooling. It is especially difficult to dissipate heat to a heat
sink in an environment in space compared to earth. For solving this
problem, in this study, the Poiseuille (Po) number, which is the main
measure of the performance of a heat pipe, is studied by CFD; then, the
heat pipe performance is verified with experimental results. A heat
pipe is then fabricated for a spatial environment, and an in-house code
is developed. Further, a heat pipe subsystem, which consists of a heat
pipe, MLI (Multi Layer Insulator), SSM (Second Surface Mirror), and
radiator, is tested and correlated with the TMM (Thermal
Mathematical Model) through a commercial code. The correlation
results satisfy the 3K requirement, and the generated thermal model is
verified for application to a spatial environment.
Abstract: This paper describes the design of a real-time audiorange
digital oscilloscope and its implementation in 90nm CMOS
FPGA platform. The design consists of sample and hold circuits,
A/D conversion, audio and video processing, on-chip RAM, clock
generation and control logic. The design of internal blocks and
modules in 90nm devices in an FPGA is elaborated. Also the key
features and their implementation algorithms are presented.
Finally, the timing waveforms and simulation results are put
forward.
Abstract: The Combination of path planning and path following is the main purpose of this paper. This paper describes the developed practical approach to motion control of the MRL small size robots. An intelligent controller is applied to control omni-directional robots motion in simulation and real environment respectively. The Brain Emotional Learning Based Intelligent Controller (BELBIC), based on LQR control is adopted for the omni-directional robots. The contribution of BELBIC in improving the control system performance is shown as application of the emotional learning in a real world problem. Optimizing of the control effort can be achieved in this method too. Next the implicit communication method is used to determine the high level strategies and coordination of the robots. Some simple rules besides using the environment as a memory to improve the coordination between agents make the robots' decision making system. With this simple algorithm our team manifests a desirable cooperation.
Abstract: The aim of this study was to investigate the
effectiveness of anaerobic digestion for the treatment of wool
scouring wastes. The experiments design comprised three ratios of
waste (W) to seed(S) (W:S) of 25:75, 50:50 and 75:25, corresponding
to 1.9. 1.7 and 1.5g tCOD/g TS, respectively, with or without
chemicals addition. NH4Cl was added to the reactors as a source for
nitrogen to achieve C:N:P of 420:14:3. A cationic flocculent was
added at 0.5 and 0.75% to enhance flocculation of sludge. The results
showed that the reactors that received W:S at a ratio of 25:75
produced the largest volume of biogas. The final soluble COD
(sCOD) was below the limits for discharge to the sewer system.
Abstract: A fusion classifier composed of two modules, one made by a hidden Markov model (HMM) and the other by a support vector machine (SVM), is proposed to recognize faces with pose variations in open-set recognition settings. The HMM module captures the evolution of facial features across a subject-s face using the subject-s facial images only, without referencing to the faces of others. Because of the captured evolutionary process of facial features, the HMM module retains certain robustness against pose variations, yielding low false rejection rates (FRR) for recognizing faces across poses. This is, however, on the price of poor false acceptance rates (FAR) when recognizing other faces because it is built upon withinclass samples only. The SVM module in the proposed model is developed following a special design able to substantially diminish the FAR and further lower down the FRR. The proposed fusion classifier has been evaluated in performance using the CMU PIE database, and proven effective for open-set face recognition with pose variations. Experiments have also shown that it outperforms the face classifier made by HMM or SVM alone.
Abstract: A combination of image fusion and quad tree decomposition method is used for detecting the sunspot trajectories in each month and computation of the latitudes of these trajectories in each solar hemisphere. Daily solar images taken with SOHO satellite are fused for each month and the result of fused image is decomposed with Quad Tree decomposition method in order to classifying the sunspot trajectories and then to achieve the precise information about latitudes of sunspot trajectories. Also with fusion we deduce some physical remarkable conclusions about sun magnetic fields behavior. Using quad tree decomposition we give information about the region on sun surface and the space angle that tremendous flares and hot plasma gases permeate interplanetary space and attack to satellites and human technical systems. Here sunspot images in June, July and August 2001 are used for studying and give a method to compute the latitude of sunspot trajectories in each month with sunspot images.
Abstract: Many agricultural and especially greenhouse
applications like plant inspection, data gathering, spraying and
selective harvesting could be performed by robots. In this paper
multiple nonholonomic robots are used in order to create a desired
formation scheme for screening solar energy in a greenhouse through
data gathering. The formation consists from a leader and a team
member equipped with appropriate sensors. Each robot is dedicated
to its mission in the greenhouse that is predefined by the
requirements of the application. The feasibility of the proposed
application includes experimental results with three unmanned
ground vehicles (UGV).
Abstract: There are some existing Java benchmarks, application benchmarks as well as micro benchmarks or mixture both of them,such as: Java Grande, Spec98, CaffeMark, HBech, etc. But none of them deal with behaviors of multi tasks operating systems. As a result, the achieved outputs are not satisfied for performance evaluation engineers. Behaviors of multi tasks operating systems are based on a schedule management which is employed in these systems. Different processes can have different priority to share the same resources. The time is measured by estimating from applications started to it is finished does not reflect the real time value which the system need for running those programs. New approach to this problem should be done. Having said that, in this paper we present a new Java benchmark, named FHOJ benchmark, which directly deals with multi tasks behaviors of a system. Our study shows that in some cases, results from FHOJ benchmark are far more reliable in comparison with some existing Java benchmarks.
Abstract: Advances in clinical medical imaging have brought about the routine production of vast numbers of medical images that need to be analyzed. As a result an enormous amount of computer vision research effort has been targeted at achieving automated medical image analysis. Computed Tomography (CT) is highly accurate for diagnosing liver tumors. This study aimed to evaluate the potential role of the wavelet and the neural network in the differential diagnosis of liver tumors in CT images. The tumors considered in this study are hepatocellular carcinoma, cholangio carcinoma, hemangeoma and hepatoadenoma. Each suspicious tumor region was automatically extracted from the CT abdominal images and the textural information obtained was used to train the Probabilistic Neural Network (PNN) to classify the tumors. Results obtained were evaluated with the help of radiologists. The system differentiates the tumor with relatively high accuracy and is therefore clinically useful.
Abstract: More and more governments around the world are
introducing e-government as a means of reducing costs, improving
services, saving time and increasing effectiveness and efficiency in
the public sector Therefore e-government has been identified as one
of the top priorities for Saudi government and all its agencies.
However, the adoption of e-government is facing many challenges
and barriers such as technological, cultural, organizational, and social
issues which must be considered and treated carefully by any
government contemplating its adoption. This paper reports on a pilot
study amongst online (e-ready) citizens to identify the challenges and
barriers that affect the adoption of e-government services especially
from their perspective in Saudi society. Based on the analysis of data
collected from an online survey the researcher was able to identify
some of the important barriers and challenges from the e-ready
citizen perspective. As a result, this study has generated a list of
possible strategies to move towards successful adoption of egovernment
services in Saudi Arabia.
Abstract: Cs-type nanocomposite zeolite membrane was successfully synthesized on an alumina ceramic hollow fibre with a mean outer diameter of 1.7 mm; cesium cationic exchange test was carried out inside test module with mean wall thickness of 230 μm and an average crossing pore size smaller than 0.2 μm. Separation factor of n-butane/H2 obtained indicate that a relatively high quality closed to 20. Maxwell-Stefan modeling provides an equivalent thickness lower than 1 µm. To compare the difference an application to CO2/N2 separation has been achieved, reaching separation factors close to (4,18) before and after cation exchange on H-zeolite membrane formed within the pores of a ceramic alumina substrate.
Abstract: This paper presents the averaging model of a buck
converter derived from the generalized state-space averaging method.
The sliding mode control is used to regulate the output voltage of the
converter and taken into account in the model. The proposed model
requires the fast computational time compared with those of the full
topology model. The intensive time-domain simulations via the exact
topology model are used as the comparable model. The results show
that a good agreement between the proposed model and the switching
model is achieved in both transient and steady-state responses. The
reported model is suitable for the optimal controller design by using
the artificial intelligence techniques.
Abstract: In the area of Human Resource Management, the trend is towards online exchange of information about human resources. For example, online applications for employment become standard and job offerings are posted in many job portals. However, there are too many job portals to monitor all of them if someone is interested in a new job. We developed a prototype for integrating information of different job portals into one meta-search engine. First, existing job portals were investigated and XML schema documents were derived automated from these portals. Second, translation rules for transforming each schema to a central HR-XML-conform schema were determined. The HR-XML-schema is used to build a form for searching jobs. The data supplied by a user in this form is now translated into queries for the different job portals. Each result obtained by a job portal is sent to the meta-search engine that ranks the result of all received job offers according to user's preferences.
Abstract: Safety instrumented systems (SISs) are becoming
increasingly complex and the proportion of programmable electronic
parts is growing. The IEC 61508 global standard was established to
ensure the functional safety of SISs, but it was expressed in highly
macroscopic terms. This study introduces an evaluation process for
hardware safety integrity levels through failure modes, effects, and
diagnostic analysis (FMEDA).FMEDA is widely used to evaluate
safety levels, and it provides the information on failure rates and
failure mode distributions necessary to calculate a diagnostic coverage
factor for a given component. In our evaluation process, the
components of the SIS subsystem are first defined in terms of failure
modes and effects. Then, the failure rate and failure mechanism
distribution are assigned to each component. The safety mode and
detectability of each failure mode are determined for each component.
Finally, the hardware safety integrity level is evaluated based on the
calculated results.
Abstract: It is important to predict yield in semiconductor test process in order to increase yield. In this study, yield prediction means finding out defective die, wafer or lot effectively. Semiconductor test process consists of some test steps and each test includes various test items. In other world, test data has a big and complicated characteristic. It also is disproportionably distributed as the number of data belonging to FAIL class is extremely low. For yield prediction, general data mining techniques have a limitation without any data preprocessing due to eigen properties of test data. Therefore, this study proposes an under-sampling method using support vector machine (SVM) to eliminate an imbalanced characteristic. For evaluating a performance, randomly under-sampling method is compared with the proposed method using actual semiconductor test data. As a result, sampling method using SVM is effective in generating robust model for yield prediction.
Abstract: This paper presents the optimum design for a double
stator, cup rotor machine; a novel type of BLDC PM Machine. The optimization approach is divided into two stages: the first stage is
calculating the machine configuration using Matlab, and the second stage is the optimization of the machine using Finite Element
Modeling (FEM). Under the design specifications, the machine
model will be selected from three pole numbers, namely, 8, 10 and 12 with an appropriate slot number. A double stator brushless DC
permanent magnet machine is designed to achieve low cogging torque; high electromagnetic torque and low ripple torque.
Abstract: While OCD is one of the most commonly occurring
psychiatric conditions experienced by older adults, there is a paucity
of research conducted into the treatment of older adults with OCD.
This case study represents the first published investigation of a
cognitive treatment for geriatric OCD. It describes the successful
treatment of an 86-year old man with a 63-year history of OCD using
Danger Ideation Reduction Therapy (DIRT). The client received 14
individual, 50-minute treatment sessions of DIRT over 13 weeks.
Clinician-based Y-BOCS scores reduced 84% from 25 (severe) at
pre-treatment, to 4 (subclinical) at 6-month post-treatment follow-up
interview, demonstrating the efficacy of DIRT for this client. DIRT
may have particular advantages over ERP and pharmacological
approaches, however further research is required in older adults with
OCD.
Abstract: Route bus system is one of fundamental transportation device for aged people and students, and has an important role in every province. However, passengers decrease year by year, therefore the authors have developed the system called "Bus-Net" as a web application to sustain the public transport. But there are two problems in Bus-Net. One is the user interface that does not consider the variety of the device, and the other is the path planning system that dose not correspond to the on-demand bus. Then, Bus-Net was improved to be able to utilize the variety of the device, and a new function corresponding to the on-demand bus was developed.
Abstract: Distant-talking voice-based HCI system suffers from
performance degradation due to mismatch between the acoustic
speech (runtime) and the acoustic model (training). Mismatch is
caused by the change in the power of the speech signal as observed at
the microphones. This change is greatly influenced by the change in
distance, affecting speech dynamics inside the room before reaching
the microphones. Moreover, as the speech signal is reflected, its
acoustical characteristic is also altered by the room properties. In
general, power mismatch due to distance is a complex problem. This
paper presents a novel approach in dealing with distance-induced
mismatch by intelligently sensing instantaneous voice power variation
and compensating model parameters. First, the distant-talking speech
signal is processed through microphone array processing, and the
corresponding distance information is extracted. Distance-sensitive
Gaussian Mixture Models (GMMs), pre-trained to capture both
speech power and room property are used to predict the optimal
distance of the speech source. Consequently, pre-computed statistic
priors corresponding to the optimal distance is selected to correct
the statistics of the generic model which was frozen during training.
Thus, model combinatorics are post-conditioned to match the power
of instantaneous speech acoustics at runtime. This results to an
improved likelihood in predicting the correct speech command at
farther distances. We experiment using real data recorded inside two
rooms. Experimental evaluation shows voice recognition performance
using our method is more robust to the change in distance compared
to the conventional approach. In our experiment, under the most
acoustically challenging environment (i.e., Room 2: 2.5 meters), our
method achieved 24.2% improvement in recognition performance
against the best-performing conventional method.