Abstract: The present work involves measurements to examine
the effects of initial conditions on aerodynamic and acoustic
characteristics of a Jet at M=0.8 by changing the orientation of sharp
edged orifice plate. A thick plate with chamfered orifice presented divergent and convergent openings when it was flipped over. The centerline velocity was found to decay more rapidly for divergent
orifice and that was consistent with the enhanced mass entrainment
suggesting quicker spread of the jet compared with that from the convergent orifice. The mixing layer region elucidated this effect of
initial conditions at an early stage – the growth was found to be comparatively more pronounced for the divergent orifice resulting in
reduced potential core size. The acoustic measurements, carried out in the near field noise region outside the jet within potential core
length, showed the jet from the divergent orifice to be less noisy. The frequency spectra of the noise signal exhibited that in the initial
region of comparatively thin mixing layer for the convergent orifice,
the peak registered a higher SPL and a higher frequency as well. The noise spectra and the mixing layer development suggested a direct correlation between the coherent structures developing in the initial
region of the jet and the noise captured in the surrounding near field.
Abstract: This paper presents a simple three phase power flow
method for solution of three-phase unbalanced radial distribution
system (RDN) with voltage dependent loads. It solves a simple
algebraic recursive expression of voltage magnitude, and all the data
are stored in vector form. The algorithm uses basic principles of
circuit theory and can be easily understood. Mutual coupling between
the phases has been included in the mathematical model. The
proposed algorithm has been tested with several unbalanced radial
distribution networks and the results are presented in the article. 8-
bus and IEEE 13 bus unbalanced radial distribution system results
are in agreements with the literature and show that the proposed
model is valid and reliable.
Abstract: In this paper we introduce an effective ECG compression algorithm based on two dimensional multiwavelet transform. Multiwavelets offer simultaneous orthogonality, symmetry and short support, which is not possible with scalar two-channel wavelet systems. These features are known to be important in signal processing. Thus multiwavelet offers the possibility of superior performance for image processing applications. The SPIHT algorithm has achieved notable success in still image coding. We suggested applying SPIHT algorithm to 2-D multiwavelet transform of2-D arranged ECG signals. Experiments on selected records of ECG from MIT-BIH arrhythmia database revealed that the proposed algorithm is significantly more efficient in comparison with previously proposed ECG compression schemes.
Abstract: This paper presents a new Quality-Controlled, wavelet based, compression method for electrocardiogram (ECG) signals. Initially, an ECG signal is decomposed using the wavelet transform. Then, the resulting coefficients are iteratively thresholded to guarantee that a predefined goal percent root mean square difference (GPRD) is matched within tolerable boundaries. The quantization strategy of extracted non-zero wavelet coefficients (NZWC), according to the combination of RLE, HUFFMAN and arithmetic encoding of the NZWC and a resulting look up table, allow the accomplishment of high compression ratios with good quality reconstructed signals.
Abstract: This paper deals with the formulation of Maxwell-s equations in a cavity resonator in the presence of the gravitational field produced by a blackhole. The metric of space-time due to the blackhole is the Schwarzchild metric. Conventionally, this is expressed in spherical polar coordinates. In order to adapt this metric to our problem, we have considered this metric in a small region close to the blackhole and expressed this metric in a cartesian system locally.
Abstract: Particle damping is a technique to reduce the
structural vibrations by means of placing small metallic particles
inside a cavity that is attached to the structure at location of high
vibration amplitudes. In this paper, we have presented an analytical
model to simulate the particle damping of two dimensional transient
vibrations in structure operating under high centrifugal loads. The
simulation results show that this technique remains effective as long
as the ratio of the dynamic acceleration of the structure to the applied
centrifugal load is more than 0.1. Particle damping increases with the
increase of particle to structure mass ratio. However, unlike to the
case of particle damping in the absence of centrifugal loads where
the damping efficiency strongly depends upon the size of the cavity,
here this dependence becomes very weak. Despite the simplicity of
the model, the simulation results are considerably in good agreement
with the very scarce experimental data available in the literature for
particle damping under centrifugal loads.
Abstract: In this paper, we present a non-blind technique of
adding the watermark to the Fourier spectral components of audio
signal in a way such that the modified amplitude does not exceed the
maximum amplitude spread (MAS). This MAS is due to individual
Discrete fourier transform (DFT) coefficients in that particular frame,
which is derived from the Energy Spreading function given by
Schroeder. Using this technique one can store double the information
within a given frame length i.e. overriding the watermark on the
host of equal length with least perceptual distortion. The watermark
is uniformly floating on the DFT components of original signal.
This helps in detecting any intentional manipulations done on the
watermarked audio. Also, the scheme is found robust to various signal
processing attacks like presence of multiple watermarks, Additive
white gaussian noise (AWGN) and mp3 compression.
Abstract: This paper presents results of an experimental study performed to investigate effect of incorporating silica fume on physico-mechanical properties and durability of resulting fly ash geopolymers. Geopolymer specimens were prepared by activating fly ash incorporated with additional silica fume in the range of 2.5% to 5%, with a mixture of sodium hydroxide and sodium silicate solution having Na2O content of 8%. For studying durability, 10% magnesium sulphate solution was used to immerse the specimens up to a period of 15 weeks during which visual observation, weight changes and strength changes were monitored regularly. Addition of silica fume lowers performance of geopolymer pastes. However, in mortars, addition of silica fume significantly enhanced physico-mechanical properties and durability.
Abstract: The orthogonal processes to shape the triangle steel plate into a equilateral vertical steel are examined by an incremental elasto-plastic finite-element method based on an updated Lagrangian formulation. The highly non-linear problems due to the geometric changes, the inelastic constitutive behavior and the boundary conditions varied with deformation are taken into account in an incremental manner. On the contact boundary, a modified Coulomb friction mode is specially considered. A weighting factor r-minimum is employed to limit the step size of loading increment to linear relation. In particular, selective reduced integration was adopted to formulate the stiffness matrix. The simulated geometries of verticality could clearly demonstrate the vertical processes until unloading. A series of experiments and simulations were performed to validate the formulation in the theory, leading to the development of the computer codes. The whole deformation history and the distribution of stress, strain and thickness during the forming process were obtained by carefully considering the moving boundary condition in the finite-element method. Therefore, this modeling can be used for judging whether a equilateral vertical steel can be shaped successfully. The present work may be expected to improve the understanding of the formation of the equilateral vertical steel.
Abstract: To derive the fractional flow equation oil
displacement will be assumed to take place under the so-called
diffusive flow condition. The constraints are that fluid saturations at
any point in the linear displacement path are uniformly distributed
with respect to thickness; this allows the displacement to be described
mathematically in one dimension. The simultaneous flow of oil and
water can be modeled using thickness averaged relative permeability,
along the centerline of the reservoir. The condition for fluid potential
equilibrium is simply that of hydrostatic equilibrium for which the
saturation distribution can be determined as a function of capillary
pressure and therefore, height. That is the fluids are distributed in
accordance with capillary-gravity equilibrium.
This paper focused on the fraction flow of water versus
cumulative oil recoveries using Buckley Leverett method. Several
field cases have been developed to aid in analysis. Producing watercut
(at surface conditions) will be compared with the cumulative oil
recovery at breakthrough for the flowing fluid.
Abstract: Natural fibres have emerged as the potential reinforcement material for composites and thus gain attraction by many researchers. This is mainly due to their applicable benefits as they offer low density, low cost, renewable, biodegradability and environmentally harmless and also comparable mechanical properties with synthetic fibre composites. The properties of hybrid composites highly depends on several factors, including the interaction of fillers with the polymeric matrix, shape and size (aspect ratio), and orientation of fillers [1]. In this study, natural fibre kenaf composites and kenaf/fibreglass hybrid composites were fabricated by a combination of hand lay-up method and cold-press method. The effect of different fibre types (powder, short and long) on the tensile properties of composites is investigated. The kenaf composites with and without the addition of fibreglass were then characterized by tensile testing and scanning electron microscopy. A significant improvement in tensile strength and modulus were indicated by the introduction of long kenaf/woven fibreglass hybrid composite. However, the opposite trends are observed in kenaf powder composite. Fractographic observation shows that fibre/matrix debonding causes the fibres pull out. This phenomenon results in the fibre and matrix fracture.
Abstract: This work presents a methodology for the selection
and design of propeller oriented to the experimental verification of
theoretical results. The problem of propeller selection and design
usually present itself in the following manner: a certain air volume
and static pressure are required for a certain system. Once the
necessity of fan design on a theoretical basis has been recognized, it
is possible to determinate the dimensions for a fan unit so that it will
perform in accordance with a certain set of specifications. The same
procedures in this work then can be applied in other propeller
selection.
Abstract: The steady coupled dissipative layers, called
Marangoni mixed convection boundary layers, in the presence of a
magnetic field and solute concentration that are formed along the
surface of two immiscible fluids with uniform suction or injection
effects is examined. The similarity boundary layer equations are
solved numerically using the Runge-Kutta Fehlberg with shooting
technique. The Marangoni, buoyancy and external pressure gradient
effects that are generated in mixed convection boundary layer flow
are assessed. The velocity, temperature and concentration boundary
layers thickness decrease with the increase of the magnetic field
strength and the injection to suction. For buoyancy-opposed flow, the
Marangoni mixed convection parameter enhances the velocity
boundary layer but decreases the temperature and concentration
boundary layers. However, for the buoyancy-assisted flow, the
Marangoni mixed convection parameter decelerates the velocity but
increases the temperature and concentration boundary layers.
Abstract: This paper has, as its point of departure, the foundational
axiomatic theory of E. De Giorgi (1996, Scuola Normale
Superiore di Pisa, Preprints di Matematica 26, 1), based on two
primitive notions of quality and relation. With the introduction of
a unary relation, we develop a system totally based on the sole
primitive notion of relation. Such a modification enables a definition
of the concept of dynamic unary relation. In this way we construct a
simple language capable to express other well known theories such
as Robinson-s arithmetic or a piece of a theory of concatenation. A
key role in this system plays an abstract relation designated by “( )",
which can be interpreted in different ways, but in this paper we will
focus on the case when we can perform computations and obtain
results.
Abstract: Mostly transforms are used for speech data
compressions which are lossy algorithms. Such algorithms are
tolerable for speech data compression since the loss in quality is not
perceived by the human ear. However the vector quantization (VQ)
has a potential to give more data compression maintaining the same
quality. In this paper we propose speech data compression algorithm
using vector quantization technique. We have used VQ algorithms
LBG, KPE and FCG. The results table shows computational
complexity of these three algorithms. Here we have introduced a new
performance parameter Average Fractional Change in Speech
Sample (AFCSS). Our FCG algorithm gives far better performance
considering mean absolute error, AFCSS and complexity as
compared to others.
Abstract: Probiotic bacteria especially Lactobacillus spp. and Bifidobacterium exert suppressive effect on Helicobacter pylori. Cinnamon and licorice have been traditionally used for the treatment of gastric ulcer. The objectives of this study were to determine the effects of herbs on yogurt fermentation, the level of probiotic bacteria in yogurt during 28 days storage and the effect of herbal yogurt on the growth of H. pylori in vitro. Cinnamon or licorice was mixed with milk and the mixture was fermented with probiotic bacteria to form herbal-yogurt. Changes of pH and total titratable acids were monitored and the viability of probiotic bacteria was evaluated during and after refrigerated storage. The in vitro inhibition of H. pylori growth was determined using agar diffusion and minimum inhibitory concentration (MIC) method. The presence of herbs did not affect the probiotic population during storage. There were no significant differences in pH and TTA between herbal-yogurts and plain-yogurt during fermentation and storage. Water extract of cinnamon-yogurt showed the highest inhibition effect (13.5mm) on H. pylori growth in comparison with licorice-yogurt (11.2mm). The present findings indicate cinnamon and licorice has bioactive components to decrease the growth of H. pylori.
Abstract: Although women have merit in their jobs, they still
are located very few in the top management in many sectors. There
are many causes of such situation. Such a situation creates obstacles;
especially invisible ones are called “glass ceiling syndrome”. Also,
studies which handle this subject in academic community are very
few. The aim of this research is to reach the results about glass
ceiling obstacles in terms of female teaching staff (academics)
working in higher education institutions. To this end, our study was
performed on female academics working at Selcuk University, Konya
/ Turkey. Our study's main aim can be expressed as to determine
whether there are glass ceiling obstacles for female academics
working at the higher education institution in question, to measure
their glass ceiling perceptions and, thus, to identify what the glass
ceiling barrier components for them to promotion to senior
management positions are.
Abstract: The equilibrium process of plasma nitrogen species by
chemical kinetic reactions along various pressures is successfully
investigated. The equilibrium process is required in industrial
application to obtain the stable condition when heating up the
material for having homogenous reaction. Nitrogen species densities
is modeled by a continuity equation and extended Arrhenius form.
These equations are used to integrate the change of density over the
time. The integration is to acquire density and the reaction rate of
each reaction where temperature and time dependence are imposed.
A comparison is made with global model within pressure range of 1-
100mTorr and the temperature of electron is set to be higher than
other nitrogen species. The results shows that the chemical kinetic
model only agrees for high pressure because of no power imposed;
while the global model considers the external power along the
pressure range then the electron and nitrogen species give highly
quantity densities by factor of 3 to 5.
Abstract: The DNA microarray technology concurrently monitors the expression levels of thousands of genes during significant biological processes and across the related samples. The better understanding of functional genomics is obtained by extracting the patterns hidden in gene expression data. It is handled by clustering which reveals natural structures and identify interesting patterns in the underlying data. In the proposed work clustering gene expression data is done through an Advanced Nelder Mead (ANM) algorithm. Nelder Mead (NM) method is a method designed for optimization process. In Nelder Mead method, the vertices of a triangle are considered as the solutions. Many operations are performed on this triangle to obtain a better result. In the proposed work, the operations like reflection and expansion is eliminated and a new operation called spread-out is introduced. The spread-out operation will increase the global search area and thus provides a better result on optimization. The spread-out operation will give three points and the best among these three points will be used to replace the worst point. The experiment results are analyzed with optimization benchmark test functions and gene expression benchmark datasets. The results show that ANM outperforms NM in both benchmarks.
Abstract: Time-Cost Optimization "TCO" is one of the greatest challenges in construction project planning and control, since the optimization of either time or cost, would usually be at the expense of the other. Since there is a hidden trade-off relationship between project and cost, it might be difficult to predict whether the total cost would increase or decrease as a result of the schedule compression. Recently third dimension in trade-off analysis is taken into consideration that is quality of the projects. Few of the existing algorithms are applied in a case of construction project with threedimensional trade-off analysis, Time-Cost-Quality relationships. The objective of this paper is to presents the development of a practical software system; that named Automatic Multi-objective Typical Construction Resource Optimization System "AMTCROS". This system incorporates the basic concepts of Line Of Balance "LOB" and Critical Path Method "CPM" in a multi-objective Genetic Algorithms "GAs" model. The main objective of this system is to provide a practical support for typical construction planners who need to optimize resource utilization in order to minimize project cost and duration while maximizing its quality simultaneously. The application of these research developments in planning the typical construction projects holds a strong promise to: 1) Increase the efficiency of resource use in typical construction projects; 2) Reduce construction duration period; 3) Minimize construction cost (direct cost plus indirect cost); and 4) Improve the quality of newly construction projects. A general description of the proposed software for the Time-Cost-Quality Trade-Off "TCQTO" is presented. The main inputs and outputs of the proposed software are outlined. The main subroutines and the inference engine of this software are detailed. The complexity analysis of the software is discussed. In addition, the verification, and complexity of the proposed software are proved and tested using a real case study.