Abstract: In this paper, an automatic detecting algorithm for
QRS complex detecting was applied for analyzing ECG recordings
and five criteria for dangerous arrhythmia diagnosing are applied for a
protocol type of automatic arrhythmia diagnosing system. The
automatic detecting algorithm applied in this paper detected the
distribution of QRS complexes in ECG recordings and related
information, such as heart rate and RR interval. In this investigation,
twenty sampled ECG recordings of patients with different pathologic
conditions were collected for off-line analysis. A combinative
application of four digital filters for bettering ECG signals and
promoting detecting rate for QRS complex was proposed as
pre-processing. Both of hardware filters and digital filters were
applied to eliminate different types of noises mixed with ECG
recordings. Then, an automatic detecting algorithm of QRS complex
was applied for verifying the distribution of QRS complex. Finally,
the quantitative clinic criteria for diagnosing arrhythmia were
programmed in a practical application for automatic arrhythmia
diagnosing as a post-processor. The results of diagnoses by automatic
dangerous arrhythmia diagnosing were compared with the results of
off-line diagnoses by experienced clinic physicians. The results of
comparison showed the application of automatic dangerous
arrhythmia diagnosis performed a matching rate of 95% compared
with an experienced physician-s diagnoses.
Abstract: In this paper, we carry over some of the results which
are valid on a certain class of Moufang-Klingenberg planes M(A)
coordinatized by an local alternative ring A := A(ε) = A+Aε of
dual numbers to finite projective Klingenberg plane M(A) obtained
by taking local ring Zq (where prime power q = pk) instead of A.
So, we show that the collineation group of M(A) acts transitively
on 4-gons, and that any 6-figure corresponds to only one inversible
m ∈ A.
Abstract: This project aims to investigate the potential of
torrefaction to improve the properties of Malaysian palm kernel shell
(PKS) as a solid fuel. A study towards torrefaction of PKS was
performed under various temperature and residence time of 240, 260,
and 280oC and 30, 60, and 90 minutes respectively. The torrefied
PKS was characterized in terms of the mass yield, energy yield,
elemental composition analysis, calorific value analysis, moisture and
volatile matter contents, and ash and fixed carbon contents. The mass
and energy yield changes in the torrefied PKS were observed to
prove that the temperature has more effect compare to residence time
in the torrefaction process. The C content of PKS increases while H
and O contents decrease after torrefaction, which resulted in higher
heating value between 5 to 16%. Meanwhile, torrefaction caused the
ash and fixed carbon content of PKS to increase, and the moisture
and volatile matter to decrease.
Abstract: Decision feedback equalizers are commonly employed to reduce the error caused by intersymbol interference. Here, an adaptive decision feedback equalizer is presented with a new adaptation algorithm. The algorithm follows a block-based approach of normalized least mean square (NLMS) algorithm with set-membership filtering and achieves a significantly less computational complexity over its conventional NLMS counterpart with set-membership filtering. It is shown in the results that the proposed algorithm yields similar type of bit error rate performance over a reasonable signal to noise ratio in comparison with the latter one.
Abstract: This paper describes Nano-particle based Planar Laser
Scattering (NPLS) flow visualization of angled supersonic jets into a
supersonic cross flow based on the HYpersonic Low TEmperature
(HYLTE) nozzle which was widely used in DF chemical laser. In
order to investigate the non-reacting flowfield in the HYLTE nozzle, a
testing section with windows was designed and manufactured. The
impact of secondary fluids orifice separation on mixing was examined.
For narrow separation of orifices, the secondary fuel penetration
increased obviously compared to diluent injection, which means
smaller separation of diluent and fuel orifices would enhance the
mixing of fuel and oxidant. Secondary injections with angles of 30, 40
and 50 degrees were studied. It was found that the injectant
penetration increased as the injection angle increased, while the
interfacial surface area to entrain the freestream fluid is largest when
the injection angle is 40 degree.
Abstract: The major source of allergy in home is the house dust
mite (Dematophagoides farina, Dermatophagoides pteronyssinus)
causing allergic symptom include atopic dermatitis, asthma, perennial
rhinitis and even infant death syndrome.
Control of this mite species is dependent on the use of chemical
methods such as fumigation treatments with methylene bromide,
spraying with organophosphates such as pirimiphos-methyl, or
treatments with repellents such as DEET and benzyl benzoate.
Although effective, their repeated use for decades has sometimes
resulted in development of resistance and fostered environmental and
human health concerns. Both decomposing animal parts and the
protein that surrounds mite fecal pellets cause mite allergy. So it is
more effective to repel than to kill them because allergen is not living
house dust mite but dead body or fecal particles of house dust mite.
It is important to find out natural repellent material against house
dust mite to control them and reduce the allergic reactions. Plants may
be an alternative source for dust mite control because they contain a
range of bioactive chemicals.
The research objectives of this paper were to verify the acaricidal
and repellent effects of cinnamon essential oil and to find out it-s most
effective concentrations. We could find that cinnamon bark essential
oil was very effective material to control the house dust mite.
Furthermore, it could reduce chemical resistance and danger for
human health.
Abstract: The rising price of fossil fuels, government incentives
and growing public aware-ness for the need to implement sustainable
energy supplies has resulted in a large in-crease in solar panel
installations across the country. For many sites the most eco-nomical
solar panel installation uses existing, southerly facing rooftops.
Adding solar panels to an existing roof typically means increased
loads that must be borne by the building-s structural elements. The
structural design professional is responsible for ensuring a new solar
panel installation is properly supported by an existing structure and
configured to maximize energy generation.
Abstract: The motion planning technique described in this paper has been developed to eliminate or reduce the residual vibrations of belt-driven rotary platforms, while maintaining unchanged the motion time and the total angular displacement of the platform. The proposed approach is based on a suitable choice of the motion command given to the servomotor that drives the mechanical device; this command is defined by some numerical coefficients which determine the shape of the displacement, velocity and acceleration profiles. Using a numerical optimization technique, these coefficients can be changed without altering the continuity conditions imposed on the displacement and its time derivatives at the initial and final time instants. The proposed technique can be easily and quickly implemented on an actual device, since it requires only a simple modification of the motion command profile mapped in the memory of the electronic motion controller.
Abstract: We introduce an extended resource leveling model that abstracts real life projects that consider specific work ranges for each resource. Contrary to traditional resource leveling problems this model considers scarce resources and multiple objectives: the minimization of the project makespan and the leveling of each resource usage over time. We formulate this model as a multiobjective optimization problem and we propose a multiobjective genetic algorithm-based solver to optimize it. This solver consists in a two-stage process: a main stage where we obtain non-dominated solutions for all the objectives, and a postprocessing stage where we seek to specifically improve the resource leveling of these solutions. We propose an intelligent encoding for the solver that allows including domain specific knowledge in the solving mechanism. The chosen encoding proves to be effective to solve leveling problems with scarce resources and multiple objectives. The outcome of the proposed solvers represent optimized trade-offs (alternatives) that can be later evaluated by a decision maker, this multi-solution approach represents an advantage over the traditional single solution approach. We compare the proposed solver with state-of-art resource leveling methods and we report competitive and performing results.
Abstract: This paper presents an automated inspection algorithm
for a thick plate. Thick plates typically have various types of surface
defects, such as scabs, scratches, and roller marks. These defects have
individual characteristics including brightness and shape. Therefore, it
is not simple to detect all the defects. In order to solve these problems
and to detect defects more effectively, we propose a dual light
switching lighting method and a defect detection algorithm based on
Gabor filters.
Abstract: In this paper, a novel road extraction method using Stationary Wavelet Transform is proposed. To detect road features from color aerial satellite imagery, Mexican hat Wavelet filters are used by applying the Stationary Wavelet Transform in a multiresolution, multi-scale, sense and forming the products of Wavelet coefficients at a different scales to locate and identify road features at a few scales. In addition, the shifting of road features locations is considered through multiple scales for robust road extraction in the asymmetry road feature profiles. From the experimental results, the proposed method leads to a useful technique to form the basis of road feature extraction. Also, the method is general and can be applied to other features in imagery.
Abstract: There are several ways of improving the performance of a vapor compression refrigeration cycle. Use of an ejector as expansion device is one of the alternative ways. The present paper aims at evaluate the performance improvement of a vapor compression refrigeration cycle under a wide range of operating conditions. A numerical model is developed and a parametric study of important parameters such as condensation (30-50°C) and evaporation temperatures (-20-5°C), nozzle and diffuser efficiencies (0.75-0.95), subcooling and superheating degrees (0-15K) are investigated. The model verification gives a good agreement with the literature data. The simulation results revealed that condensation temperature has the highest effect (129%) on the performance improvement ratio while superheating has the lowest one (6.2%). Among ejector efficiencies, the diffuser efficiency has a significant effect on the COP of ejector expansion refrigeration cycle. The COP improvement percentage decreases from 10.9% to 4.6% as subcooling degrees increases by 15K.
Abstract: The goal of speech parameterization is to extract the relevant information about what is being spoken from the audio signal. In speech recognition systems Mel-Frequency Cepstral Coefficients (MFCC) and Relative Spectral Mel-Frequency Cepstral Coefficients (RASTA-MFCC) are the two main techniques used. It will be shown in this paper that it presents some modifications to the original MFCC method. In our work the effectiveness of proposed changes to MFCC called Modified Function Cepstral Coefficients (MODFCC) were tested and compared against the original MFCC and RASTA-MFCC features. The prosodic features such as jitter and shimmer are added to baseline spectral features. The above-mentioned techniques were tested with impulsive signals under various noisy conditions within AURORA databases.
Abstract: We have proposed an information filtering system
using index word selection from a document set based on the
topics included in a set of documents. This method narrows
down the particularly characteristic words in a document set
and the topics are obtained by Sparse Non-negative Matrix
Factorization. In information filtering, a document is often
represented with the vector in which the elements correspond
to the weight of the index words, and the dimension of the
vector becomes larger as the number of documents is
increased. Therefore, it is possible that useless words as index
words for the information filtering are included. In order to
address the problem, the dimension needs to be reduced. Our
proposal reduces the dimension by selecting index words
based on the topics included in a document set. We have
applied the Sparse Non-negative Matrix Factorization to the
document set to obtain these topics. The filtering is carried out
based on a centroid of the learning document set. The centroid
is regarded as the user-s interest. In addition, the centroid is
represented with a document vector whose elements consist of
the weight of the selected index words. Using the English test
collection MEDLINE, thus, we confirm the effectiveness of
our proposal. Hence, our proposed selection can confirm the
improvement of the recommendation accuracy from the other
previous methods when selecting the appropriate number of
index words. In addition, we discussed the selected index
words by our proposal and we found our proposal was able to
select the index words covered some minor topics included in
the document set.
Abstract: For improving the efficiency of human 3D tracking, we
present an algorithm to track 3D Arm Motion. First, the Hierarchy
Limb Model (HLM) is proposed based on the human 3D skeleton
model. Second, via graph decomposition, the arm motion state space,
modeled by HLM, can be discomposed into two low dimension
subspaces: root nodes and leaf nodes. Finally, Rao-Blackwellised
Particle Filter is used to estimate the 3D arm motion. The result of
experiment shows that our algorithm can advance the computation
efficiency.
Abstract: The morphological short-term evolution of Ponta do Tubarão Island (PTI) was investigated through high accurate surveys based on post-processed kinematic (PPK) relative positioning on Global Navigation Satellite Systems (GNSS). PTI is part of a barrier island system on a high energy northeast Brazilian coastal environment and also an area of high environmental sensitivity. Surveys were carried out quarterly over a two years period from May 2010 to May 2012. This paper assesses statically the performance of digital elevation models (DEM) derived from different interpolation methods to represent morphologic features and to quantify volumetric changes and TIN models shown the best results to that purposes. The MDE allowed quantifying surfaces and volumes in detail as well as identifying the most vulnerable segments of the PTI to erosion and/or accumulation of sediments and relate the alterations to climate conditions. The coastal setting and geometry of PTI protects a significant mangrove ecosystem and some oil and gas facilities installed in the vicinities from damaging effects of strong oceanwaves and currents. Thus, the maintenance of PTI is extremely required but the prediction of its longevity is uncertain because results indicate an irregularity of sedimentary balance and a substantial decline in sediment supply to this coastal area.
Abstract: The complex shape of the human pelvic bone was
successfully imaged and modeled using finite element FE processing.
The bone was subjected to quasi-static and dynamic loading
conditions simulating the effect of both weight gain and impact.
Loads varying between 500 – 2500 N (~50 – 250 Kg of weight) was
used to simulate 3D quasi-static weight gain. Two different 3D
dynamic analyses, body free fall at two different heights (1 and 2 m)
and forced side impact at two different velocities (20 and 40 Km/hr)
were also studied. The computed resulted stresses were compared for
the four loading cases, where Von Misses stresses increases linearly
with the weight gain increase under quasi-static loading. For the
dynamic models, the Von Misses stress history behaviors were
studied for the affected area and effected load with respect to time.
The normalization Von Misses stresses with respect to the applied
load were used for comparing the free fall and the forced impact load
results. It was found that under the forced impact loading condition
an over lapping behavior was noticed, where as for the free fall the
normalized Von Misses stresses behavior was found to nonlinearly
different. This phenomenon was explained through the energy
dissipation concept. This study will help designers in different
specialization in defining the weakest spots for designing different
supporting systems.
Abstract: Sixteen selected deep-sea fish obtained from Southern
Java Ocean and Western Sumatra Ocean was analyzed to determine
its proximate, fatty acid and mineral composition. The moisture
content was ranged from 64.38 to 86.04 %, ash from 0.17 to 0.69 %,
the fat content was 1.54 – 13.30 % while the protein content varied
from 15.84 to 23.60%. Among the fatty acids, oleic acid and palmitic
acid was the dominant MUFA and SFA. Linoleic acid was the
highest PUFA found at the selected deep-sea fish. Phospor was the
highest macroelement concentration on selected deep-sea fish,
followed by K, Ca, Mg and Iod, Fe and Zn among microelement. The
trace concentration was found at Se microelement.
Abstract: The alternative technique for sterilization of culture
medium to replace autoclaving was carried out. For sterilization of
culture medium without autoclaving, some commercial pure essential
oils, bergamot oil, betel oil, cinnamon oil, lavender oil and turmeric
oil, were tested alone or in combinations with some disinfectants,
10% povidone-iodine and 2% iodine + 2.4% potassium iodide. Each
essential oil or combination was added to 25-mL Murashige and
Skoog (MS) medium before medium was solidified in a 120-mL
container, kept for 2 weeks before evaluating sterile conditions.
Treated media, supplemented with essential oils, were compared to
control medium, autoclaved at 121 degree Celsius for 15 min. In
vitro sterile conditions were found 20 – 100% from these treated
media compared to 100% sterile condition from autoclaved medium.
Treated media obtained 100% sterile conditions were chosen for
culturing chrysanthemum shoots. It was found that 10% povidoneiodine
in combination with cinnamon oil (3:1) and 2% iodine + 2.4%
potassium iodide in combination with lavender oil (1:3) at the
concentration of 36 3L/25 mL medium provided the promising
growth of shoot explants.
Abstract: Efficient storage, transmission and use of video information are key requirements in many multimedia applications currently being addressed by MPEG-4. To fulfill these requirements, a new approach for representing video information which relies on an object-based representation, has been adopted. Therefore, objectbased watermarking schemes are needed for copyright protection. This paper proposes a novel blind object watermarking scheme for images and video using the in place lifting shape adaptive-discrete wavelet transform (SA-DWT). In order to make the watermark robust and transparent, the watermark is embedded in the average of wavelet blocks using the visual model based on the human visual system. Wavelet coefficients n least significant bits (LSBs) are adjusted in concert with the average. Simulation results shows that the proposed watermarking scheme is perceptually invisible and robust against many attacks such as lossy image/video compression (e.g. JPEG, JPEG2000 and MPEG-4), scaling, adding noise, filtering, etc.