Abstract: Air bubbles have been detected in human circulation
of end-stage renal disease patients who are treated by hemodialysis.
The consequence of air embolism, air bubbles, is under recognized
and usually overlooked in daily practice. This paper shows results of
a capacitor based detection method that capable of detecting the
presence of air bubbles in the blood stream in different frequencies.
The method is based on a parallel plates capacitor made of platinum
with an area of 1.5 cm2 and a distance between the two plates is 1cm.
The dielectric material used in this capacitor is Dextran70 solution
which mimics blood rheology. Simulations were carried out using
RC circuit at two frequencies 30Hz and 3 kHz and results compared
with experiments and theory. It is observed that by injecting air
bubbles of different diameters into the device, there were significant
changes in the capacitance of the capacitor. Furthermore, it is
observed that the output voltage from the circuit increased with
increasing air bubble diameter. These results demonstrate the
feasibility of this approach in improving air bubble detection in
Hemodialysis.
Abstract: The direct discharge of palm oil mill effluent (POME) wastewater causes serious environmental pollution due to its high chemical oxygen demand (COD) and biochemical oxygen demand (BOD). Traditional ways for POME treatment have both economical and environmental disadvantages. In this study, a membrane anaerobic system (MAS) was used as an alternative, cost effective method for treating POME. Six steady states were attained as a part of a kinetic study that considered concentration ranges of 8,220 to 15,400 mg/l for mixed liquor suspended solids (MLSS) and 6,329 to 13,244 mg/l for mixed liquor volatile suspended solids (MLVSS). Kinetic equations from Monod, Contois and Chen & Hashimoto were employed to describe the kinetics of POME treatment at organic loading rates ranging from 2 to 13 kg COD/m3/d. throughout the experiment, the removal efficiency of COD was from 94.8 to 96.5% with hydraulic retention time, HRT from 400.6 to 5.7 days. The growth yield coefficient, Y was found to be 0.62gVSS/g COD the specific microorganism decay rate was 0.21 d-1 and the methane gas yield production rate was between 0.25 l/g COD/d and 0.58 l/g COD/d. Steady state influent COD concentrations increased from 18,302 mg/l in the first steady state to 43,500 mg/l in the sixth steady state. The minimum solids retention time, which was obtained from the three kinetic models ranged from 5 to 12.3 days. The k values were in the range of 0.35 – 0.519 g COD/ g VSS • d and values were between 0.26 and 0.379 d-1. The solids retention time (SRT) decreased from 800 days to 11.6 days. The complete treatment reduced the COD content to 2279 mg/l equivalent to a reduction of 94.8% reduction from the original.
Abstract: A research project dealing with the phytoremediation
of a soil polluted by some heavy metals is currently running. The
case study is represented by a mining area in Hamedan province in
the central west part of Iran. The potential of phytoextraction and
phytostabilization of plants was evaluated considering the
concentration of heavy metals in the plant tissues and also the
bioconcentration factor (BCF) and the translocation factor (TF). Also
the several established criteria were applied to define
hyperaccumulator plants in the studied area. Results showed that
none of the collected plant species were suitable for phytoextraction
of Cu, Zn, Fe and Mn, but among the plants, Euphorbia macroclada
was the most efficient in phytostabilization of Cu and Fe, while,
Ziziphora clinopodioides, Cousinia sp. and Chenopodium botrys
were the most suitable for phytostabilization of Zn and Chondrila
juncea and Stipa barbata had the potential for phytostabilization of
Mn. Using the most common criterion, Euphorbia macroclada and
Verbascum speciosum were Fe hyperaccumulator plants. Present
study showed that native plant species growing on contaminated sites
may have the potential for phytoremediation.
Abstract: Let D = 1 be a positive non-square integer and let δ = √D or 1+√D 2 be a real quadratic irrational with trace t =δ + δ and norm n = δδ. Let γ = P+δ Q be a quadratic irrational for positive integers P and Q. Given a quadratic irrational γ, there exist a quadratic ideal Iγ = [Q, δ + P] and an indefinite quadratic form Fγ(x, y) = Q(x−γy)(x−γy) of discriminant Δ = t
2−4n. In the first section, we give some preliminaries form binary quadratic forms, quadratic irrationals and quadratic ideals. In the second section, we obtain some results on γ, Iγ and Fγ for some specific values of Q and P.
Abstract: A method of dynamic mesh based airfoil optimization is proposed according to the drawbacks of surrogate model based airfoil optimization. Programs are designed to achieve the dynamic mesh. Boundary condition is add by integrating commercial software Pointwise, meanwhile the CFD calculation is carried out by commercial software Fluent. The data exchange and communication between the software and programs referred above have been accomplished, and the whole optimization process is performed in iSIGHT platform. A simplified airfoil optimization study case is brought out to show that aerodynamic performances of airfoil have been significantly improved, even save massive repeat operations and increase the robustness and credibility of the optimization result. The case above proclaims that dynamic mesh based airfoil optimization is an effective and high efficient method.
Abstract: Organic Flash Cycle (OFC) has potential of improving
efficiency for recovery of low temperature heat sources mainly due to
reducing temperature mismatch in the heat exchanger. In this work
exergetical performance analysis of ORC is conducted for recovery of
low grade heat source. Effects of system parameters such as flash
evaporation temperature or heating temperature are theoretically
investigated on the exergy destructions (anergies) at various
components of the system as well as exergy efficiency. Results show
that exergy efficiency has a peak with respect to the flash temperature,
and the optimum flash temperature increases with the heating
temperature. The component where the largest exergy destruction
occurs varies with the flash temperature or heating temperature.
Abstract: It is difficult to judge ripeness by outward
characteristics such as size or external color. In this paper a nondestructive
method was studied to determine watermelon (Crimson
Sweet) quality. Responses of samples to excitation vibrations were
detected using laser Doppler vibrometry (LDV) technology. Phase
shift between input and output vibrations were extracted overall
frequency range. First and second were derived using frequency
response spectrums. After nondestructive tests, watermelons were
sensory evaluated. So the samples were graded in a range of ripeness
based on overall acceptability (total desired traits consumers).
Regression models were developed to predict quality using obtained
results and sample mass. The determination coefficients of the
calibration and cross validation models were 0.89 and 0.71
respectively. This study demonstrated feasibility of information
which is derived vibration response curves for predicting fruit
quality. The vibration response of watermelon using the LDV method
is measured without direct contact; it is accurate and timely, which
could result in significant advantage for classifying watermelons
based on consumer opinions.
Abstract: In the present paper, a set of parametric FE stress
analyses is carried out for two-planar welded tubular DKT-joints
under two different axial load cases. Analysis results are used to
present general remarks on the effect of geometrical parameters on
the stress concentration factors (SCFs) at the inner saddle, outer
saddle, toe, and heel positions on the main (outer) brace. Then a new
set of SCF parametric equations is developed through nonlinear
regression analysis for the fatigue design of two-planar DKT-joints.
An assessment study of these equations is conducted against the
experimental data; and the satisfaction of the criteria regarding the
acceptance of parametric equations is checked. Significant effort has
been devoted by researchers to the study of SCFs in various uniplanar
tubular connections. Nevertheless, for multi-planar joints
covering the majority of practical applications, very few
investigations have been reported due to the complexity and high
cost involved.
Abstract: The effect of a chiral bianisotropic substrate on the
complex resonant frequency of a rectangular microstrip resonator has
been studied on the basis of the integral equation formulation. The
analysis is based on numerical resolution of the integral equation
using Galerkin procedure for moment method in the spectral domain.
This work aim first to study the effect of the chirality of a
bianisotopic substrate upon the resonant frequency and the half
power bandwidth, second the effect of a magnetic anisotropy via an
asymptotic approach for very weak substrate upon the resonant
frequency and the half power bandwidth has been investigated. The
obtained results are compared with previously published work [11-9],
they were in good agreement.
Abstract: This paper describes the historical development of
interethnic concord in the Republic of Kazakhstan, and emphasizes
the role of tolerance mentality of the Kazakh people in ethno-political
policy of the country. Moreover, pointing out interethnic concord as a
powerful stabilizing factor, it analyses the specifics of interethnic
policy in multinational Kazakh society. It summarizes that the culture
of interethnic concord can be a model of ethno- political policy of
Kazakhstan.
Abstract: This paper considers the influence of promotion
instruments for renewable energy sources (RES) on a multi-energy
modeling framework. In Europe, so called Feed-in Tariffs are
successfully used as incentive structures to increase the amount of
energy produced by RES. Because of the stochastic nature of large
scale integration of distributed generation, many problems have
occurred regarding the quality and stability of supply. Hence, a
macroscopic model was developed in order to optimize the power
supply of the local energy infrastructure, which includes electricity,
natural gas, fuel oil and district heating as energy carriers. Unique
features of the model are the integration of RES and the adoption of
Feed-in Tariffs into one optimization stage. Sensitivity studies are
carried out to examine the system behavior under changing profits
for the feed-in of RES. With a setup of three energy exchanging
regions and a multi-period optimization, the impact of costs and
profits are determined.
Abstract: In this paper, an H1-Galerkin mixed finite element method is discussed for the coupled Burgers equations. The optimal error estimates of the semi-discrete and fully discrete schemes of the coupled Burgers equation are derived.
Abstract: The decisions made by admission control algorithms are
based on the availability of network resources viz. bandwidth, energy,
memory buffers, etc., without degrading the Quality-of-Service (QoS)
requirement of applications that are admitted. In this paper, we
present an energy-aware admission control (EAAC) scheme which
provides admission control for flows in an ad hoc network based
on the knowledge of the present and future residual energy of the
intermediate nodes along the routing path. The aim of EAAC is to
quantify the energy that the new flow will consume so that it can
be decided whether the future residual energy of the nodes along
the routing path can satisfy the energy requirement. In other words,
this energy-aware routing admits a new flow iff any node in the
routing path does not run out of its energy during the transmission
of packets. The future residual energy of a node is predicted using
the Multi-layer Neural Network (MNN) model. Simulation results
shows that the proposed scheme increases the network lifetime. Also
the performance of the MNN model is presented.
Abstract: This paper presents the effect of corrugation profile
geometry on the crushing behavior, energy absorption, failure
mechanism, and failure mode of woven roving glass fibre/epoxy
laminated composite tube. Experimental investigations were carried
out on composite tubes with three different profile shapes: sinusoidal,
triangular and trapezoidal. The tubes were subjected to lateral
compressive loading. On the addition to a radial corrugated
composite tube, cylindrical composite tube, were fabricated and
tested under the same condition in order to know the effect of
corrugation geometry. Typical histories of their deformation are
presented. Behavior of tubes as regards the peak crushing load,
energy absorbed and mode of crushing has been discussed. The
results show that the behavior of the tube under lateral compression
load is influenced by the geometry of the tube itself.
Abstract: The Carrier Frequency Offset (CFO) due to timevarying
fading channel is the main cause of the loss of orthogonality
among OFDM subcarriers which is linked to inter-carrier interference
(ICI). Hence, it is necessary to precisely estimate and compensate the
CFO. Especially for mobile broadband communications, CFO and
channel gain also have to be estimated and tracked to maintain the
system performance. Thus, synchronization pilots are embedded in
every OFDM symbol to track the variations. In this paper, we present
the pilot scheme for both channel and CFO estimation where channel
estimation process can be carried out with only one OFDM symbol.
Additional, the proposed pilot scheme also provides better
performance in CFO estimation comparing with the conventional
orthogonal pilot scheme due to the increasing of signal-tointerference
ratio.
Abstract: The effect of the number of quantum dot (QD) layers
on the saturated gain of doped QD semiconductor optical amplifiers
(SOAs) has been studied using multi-population coupled rate
equations. The developed model takes into account the effect of
carrier coupling between adjacent layers. It has been found that
increasing the number of QD layers (K) increases the unsaturated
optical gain for K
Abstract: Soil organic carbon (SOC) plays a key role in soil
fertility, hydrology, contaminants control and acts as a sink or source
of terrestrial carbon content that can affect the concentration of
atmospheric CO2. SOC supports the sustainability and quality of
ecosystems, especially in semi-arid region. This study was
conducted to determine relative importance of 13 different
exploratory climatic, soil and geometric factors on the SOC contents
in one of the semiarid watershed zones in Iran. Two methods
canonical discriminate analysis (CDA) and feed-forward back
propagation neural networks were used to predict SOC. Stepwise
regression and sensitivity analysis were performed to identify
relative importance of exploratory variables. Results from sensitivity
analysis showed that 7-2-1 neural networks and 5 inputs in CDA
models output have highest predictive ability that explains %70 and
%65 of SOC variability. Since neural network models outperformed
CDA model, it should be preferred for estimating SOC.
Abstract: Work Breakdown Structure (WBS) is one of the
most vital planning processes of the project management since it
is considered to be the fundamental of other processes like
scheduling, controlling, assigning responsibilities, etc. In fact
WBS or activity list is the heart of a project and omission of a
simple task can lead to an irrecoverable result. There are some
tools in order to generate a project WBS. One of the most
powerful tools is mind mapping which is the basis of this article.
Mind map is a method for thinking together and helps a project
manager to stimulate the mind of project team members to
generate project WBS. Here we try to generate a WBS of a
sample project involving with the building construction using the
aid of mind map and the artificial intelligence (AI) programming
language. Since mind map structure can not represent data in a
computerized way, we convert it to a semantic network which can
be used by the computer and then extract the final WBS from the
semantic network by the prolog programming language. This
method will result a comprehensive WBS and decrease the
probability of omitting project tasks.
Abstract: Behavior of turbulent jet is relying on jet parameters,
environmental and geometric parameters. In this research, it has
attempt to Study effect of jet parameters of internal angle on
maximum effective length and velocity on centerline from nozzle
experimentally. Toward this end, four internal angles 30, 45, 60 and
90-degree are considered for this study in a flume with 600cm as
long, 100cm as high and 150cm in width. Various discharges were
used to evaluate effective length for a wide range of densimetric
Froude numbers F0, from 17.9 to 39.4 that is defined at the nozzle. As
a result, It is revealed that both velocity on centerline and effective
length decreases when nozzle angle decreased from 90° to 30°. The
results show that, for all range of Fr0 the Um/U0 ratio for nozzle with
α=90° on centerline increases 20% - 27% than nozzle with α=30° that
has lowest velocity on centerline than other nozzle.
Abstract: Abstraction of water from the dry river sand-beds is
well-known as an alternative source of water during dry seasons.
Internally, because of the form of sand particles, voids are created
which can store water in the riverbeds. Large rivers are rare in South
Africa. Many rivers are sand river types and without water during the
prolonged dry periods. South Africa has not taken full advantage of
water storage in sand as a solution to the growing water scarcity both
in urban and rural areas. The paper reviews the benefits of run-off
storage in sand reservoirs gained from other arid areas and need for
adoption in rural areas of South Africa as an alternative water supply
where it is probable.