Abstract: The model tests were conducted in the laboratory
without and with Plastic recycled polymer in fly ash steep slopes
overlaying soft foundation soils like fly ash and powai soil in order to
check the stability of steep slope. In this experiment, fly ash is used
as a filling material and Plastic Recycled Polymers of diameter =
3mm and length = 4mm were made from waste plastic product (lower
grade plastic product). The properties of fly ash and Plastic recycled
polymers are determined. From the experiments, load and settlement
have measured. From these data, load –settlement curves have
reported. It has been observed from test results that load carrying
capacity of mixture fly ash with Plastic Recycled Polymers slope is
more than that of fly ash slope. The deformation of Plastic Recycled
Polymers slope is slightly more than that of fly ash slope. A Finite
Element Method (F.E.M.) was also evaluated using PLAXIS 3D
version. The failure pattern, deformations and factor of safety are
reported based on analytical programme. The results from
experimental data and analytical programme are compared and
reported.
Abstract: The largest share of policy and money within the
European Union goes to agriculture. The Union’s Common
Agricultural Policy has undergone several transformations in the last
five decades, with the main change taking place in the 1990s. This
change influenced agriculture in the Czech Republic, inasmuch as the
fledgling republic was preparing to join the European Union and
adopt its policies. In the 1990s, Czech agriculture passed from
a centrally planned economy to a market economy and subsequently
adopted the terms of the Common Agricultural Policy. The Czech
Republic is also characterized by a significant diversification of
landscape sphere. Agricultural entrepreneurs in the Czech Republic
are still not accustomed to the possibility of grants from the European
Union. They focus rather on national or regional subsidies. Only half
of all agricultural entrepreneurs in the Czech Republic use European
subsidies. This article focuses on the introduction of the Common
Agricultural Policy to the Czech Republic and its subsequent
influence on Czech agriculture. It is demonstrated through the
implementation rate of the CAP in the EU Member States and
a closer focus on Czech integration.
Abstract: The past two decades, Thailand faced the natural
disasters, for instance, Gay typhoon in 1989, tsunami in 2004, and
huge flood in 2011. The disaster management in Thailand was
improved both structure and mechanism for cope with the natural
disaster since 2007. However, the natural disaster management in
Thailand has various problems, for examples, cooperation between
related an organizations have not unity, inadequate resources, the
natural disaster management of public sectors not proactive, people
has not awareness the risk of the natural disaster, and communities
did not participate in the natural disaster management.
Objective of this study is to find the methods for capacity building
in the natural disaster management of Thailand. The concept and
information about the capacity building and the natural disaster
management of Thailand were reviewed and analyzed by classifying
and organizing data. The result found that the methods for capacity
building in the natural disaster management of Thailand should be
consist of 1) link operation and information in the natural disaster
management between nation, province, local and community levels,
2) enhance competency and resources of public sectors which relate
to the natural disaster management, 3) establish proactive natural
disaster management both planning and implementation, 4)
decentralize the natural disaster management to local government
organizations, 5) construct public awareness in the natural disaster
management to community, 6) support Community Based Disaster
Risk Management (CBDRM) seriously, and 7) emphasis on
participation in the natural disaster management of all stakeholders.
Abstract: Indonesian higher education has experienced
significant changes over the last decade. In 1999, the government
published an overall strategy for decentralisation and enhancement of
local autonomy in many sectors, including (higher) education.
Indonesian higher education reforms have forced universities to
restructure their internal university governance to become more
entrepreneurial. These new types of internal university governance
are likely to affect the institutions’ leadership and management. This
paper discusses the approach and findings of a study on the
managerial leadership styles of deans in Indonesian universities. The
study aims to get a better understanding of styles exhibited by deans
manifested in their behaviours. Using the theories of reasoned action
and planned behaviour, in combination with the competing values
framework, a large-scale survey was conducted to gather information
on the deans’ behaviours, attitudes, subjective norms, and perceived
behavioural control. Based on the responses of a sample of 218
deans, the study identifies a number of leadership styles: the Master,
the Competitive Consultant, the Consensual Goal-Setter, the Focused
Team Captain, and the Informed Trust-Builder style. The study
demonstrates that attitudes are the primary determinant of the styles
that were found. Perceived behavioural control is a factor that
explains some managerial leadership styles. By understanding the
attitudes of deans in Indonesian universities, and their leadership
styles, universities can strengthen their management and governance,
and thus improve their effectiveness.
Abstract: This paper proposes the application of the Smart
Security Concept in the East Mediterranean. Smart Security aims to
secure critical infrastructure, such as hydrocarbon platforms, against
asymmetrical threats. The concept is based on Anti Asymmetrical
Area Denial (A3D) which necessitates limiting freedom of action of
maritime terrorists and piracy by founding safe and secure maritime
areas through sea lines of communication using short range
capabilities.
Abstract: The efficiency of the actuation system of exoskeletons
and active orthoses for lower limbs is a significant aspect of the
design of such devices because it affects their efficacy. The F-IVT is
an innovative actuation system to power artificial knee joint with
energy recovery capabilities. Its key and non-conventional elements
are a flywheel that acts as a mechanical energy storage system, and
an Infinitely Variable Transmission (IVT). The design of the F-IVT
can be optimized for a certain walking condition, resulting in a heavy
reduction of both the electric energy consumption and of the electric
peak power. In this work, by means of simulations of level ground
walking at different speeds, it is demonstrated that the F-IVT is still
an advantageous actuator which permits to save energy consumption
and to downsize the electric motor even when it does not work in
nominal conditions.
Abstract: Transmission system performance analysis is vital to
proper planning and operations of power systems in the presence of
deregulation. Key performance indicators (KPIs) are often used as
measure of degree of performance. This paper gives a novel method
to determine the transmission efficiency by evaluating the ratio of
real power losses incurred from a specified transfer direction.
Available Transmission Transfer Efficiency (ATTE) expresses the
percentage of real power received resulting from inter-area available
power transfer. The Tie line (Rated system path) performance is seen
to differ from system wide (Network response) performance and
ATTE values obtained are transfer direction specific. The required
sending end quantities with specified receiving end ATC and the
receiving end power circle diagram are obtained for the tie line
analysis. The amount of real power loss load relative to the available
transfer capability gives a measure of the transmission grid
efficiency.
Abstract: The principle of the seismic performance evaluation methods is to provide a measure of capability for a building or set of buildings to be damaged by an earthquake. The common objective of many of these methods is to supply classification criteria. The purpose of this study is to present a method for assessing the seismic performance of structures, based on Pushover method; we are particularly interested in reinforced concrete frame structures, which represent a significant percentage of damaged structures after a seismic event. The work is based on the characterization of seismic movement of the various earthquake zones in terms of PGA and PGD that is obtained by means of SIMQK_GR and PRISM software and the correlation between the points of performance and the scalar characterizing the earthquakes will developed.
Abstract: Reflux condensation occurs in vertical channels and tubes when there is an upward core flow of vapour (or gas-vapour mixture) and a downward flow of the liquid film. The understanding of this condensation configuration is crucial in the design of reflux condensers, distillation columns, and in loss-of-coolant safety analyses in nuclear power plant steam generators. The unique feature of this flow is the upward flow of the vapour-gas mixture (or pure vapour) that retards the liquid flow via shear at the liquid-mixture interface. The present model solves the full, elliptic governing equations in both the film and the gas-vapour core flow. The computational mesh is non-orthogonal and adapts dynamically the phase interface, thus produces a sharp and accurate interface. Shear forces and heat and mass transfer at the interface are accounted for fundamentally. This modeling is a big step ahead of current capabilities by removing the limitations of previous reflux condensation models which inherently cannot account for the detailed local balances of shear, mass, and heat transfer at the interface. Discretisation has been done based on finite volume method and co-located variable storage scheme. An in-house computer code was developed to implement the numerical solution scheme. Detailed results are presented for laminar reflux condensation from steam-air mixtures flowing in vertical parallel plate channels. The results include velocity and gas mass fraction profiles, as well as axial variations of film thickness.
Abstract: Wavelength Division Multiplexing (WDM) is the dominant transport technology used in numerous high capacity backbone networks, based on optical infrastructures. Given the importance of costs (CapEx and OpEx) associated to these networks, resource management is becoming increasingly important, especially how the optical circuits, called “lightpaths”, are routed throughout the network. This requires the use of efficient algorithms which provide routing strategies with the lowest cost. We focus on the lightpath routing and wavelength assignment problem, known as the RWA problem, while optimizing wavelength fragmentation over the network. Wavelength fragmentation poses a serious challenge for network operators since it leads to the misuse of the wavelength spectrum, and then to the refusal of new lightpath requests. In this paper, we first establish a new Integer Linear Program (ILP) for the problem based on a node-link formulation. This formulation is based on a multilayer approach where the original network is decomposed into several network layers, each corresponding to a wavelength. Furthermore, we propose an efficient heuristic for the problem based on a greedy algorithm followed by a post-treatment procedure. The obtained results show that the optimal solution is often reached. We also compare our results with those of other RWA heuristic methods
Abstract: The paper shows the necessity of farm diversification
in accordance with the current trends in agricultural sector of
Georgia. The possibilities for the diversification and the
corresponding economic policy are suggested.
The causes that hinder diversification of farms are revealed,
possibilities of diversification are identified and the ability of
increasing employment through diversification is proved. Index of
harvest diversification is calculated based on the areas used for
cereals and legumes, potatoes and vegetables and other food crops.
Crop and livestock production indexes are analyzed; correlation
between crop capacity index and value added per worker and per
hectare is studied.
Based on the research farm diversification strategies and priorities
of corresponding economic policy are presented. Based on the
conclusions relevant recommendations are suggested.
Abstract: A numerical model has been developed to investigate the thermally triggered release kinetics for drug delivery using phase change material as shell of microcapsules. Biocompatible material n-Eicosane is used as demonstration. PCM shell of microcapsule will remain in solid form after the drug is taken, so the drug will be encapsulated by the shell, and will not be released until the target body part of lesion is exposed to external heat source, which will thermally trigger the release kinetics, leading to solid-to-liquid phase change. The findings can lead to better understanding on the key effects influencing the phase change process for drug delivery applications. The facile approach to release drug from core/shell structure of microcapsule can be well integrated with organic solvent free fabrication of microcapsules, using double emulsion as template in microfluidic aqueous two phase system.
Abstract: Honeys are produced by Apis mellifera and stingless
bees (Meliponini) in Ecuador. We studied honey produced in
beeswax combs by Apis mellifera, and honey produced in pots by
Geotrigona and Scaptotrigona bees. Chloroform extracts of honey
were obtained for fast NMR spectra. The 1D spectra were acquired at
298 K, with a 600 MHz NMR Bruker instrument, using a modified
double pulsed field gradient spin echoes (DPFGSE) sequence.
Signals of 1H NMR spectra were integrated and used as inputs for
PCA, PLS-DA analysis, and labelled sets of classes were successfully
identified, enhancing the separation between the three groups of
honey according to the entomological origin: A. mellifera,
Geotrigona and Scaptotrigona. This procedure is therefore
recommended for authenticity test of honey in Ecuador.
Abstract: Control of honey frauds is needed in Ecuador to
protect bee keepers and consumers because simple syrups and new
syrups with eucalyptus are sold as genuine honeys. Authenticity of
Ecuadorian commercial honeys was tested with a vortex emulsion
consisting on one volume of honey:water (1:1) dilution, and two
volumes of diethyl ether. This method allows a separation of phases
in one minute to discriminate genuine honeys that form three phase
and fake honeys that form two phases; 34 of the 42 honeys analyzed
from five provinces of Ecuador were genuine. This was confirmed
with 1H NMR spectra of honey dilutions in deuterated water with an
enhanced amino acid region with signals for proline, phenylalanine
and tyrosine. Classic quality indicators were also tested with this
method (sugars, HMF), indicators of fermentation (ethanol, acetic
acid), and residues of citric acid used in the syrup manufacture. One
of the honeys gave a false positive for genuine, being an admixture of
genuine honey with added syrup, evident for the high sucrose.
Sensory analysis was the final confirmation to recognize the honey
groups studied here, namely honey produced in combs by Apis
mellifera, fake honey, and honey produced in cerumen pots by
Geotrigona, Melipona, and Scaptotrigona. Chloroform extractions of
honey were also done to search lipophilic additives in NMR spectra.
This is a valuable contribution to protect honey consumers, and to
develop the beekeeping industry in Ecuador.
Abstract: Scrubbing by a liquid spraying is one of the most
effective processes used for removal of fine particles and soluble
gas pollutants (such as SO2, HCl, HF) from the flue gas. There are
many configurations of scrubbers designed to provide contact
between the liquid and gas stream for effectively capturing
particles or soluble gas pollutants, such as spray plates, packed bed
towers, jet scrubbers, cyclones, vortex and venturi scrubbers. The
primary function of venturi scrubber is the capture of fine particles
as well as HCl, HF or SO2 removal with effect of the flue gas
temperature decrease before input to the absorption column. In this
paper, sulfur dioxide (SO2) from flue gas was captured using new
design replacing venturi scrubber (1st degree of wet scrubbing).
The flue gas was prepared by the combustion of the carbon
disulfide solution in toluene (1:1 vol.) in the flame in the reactor.
Such prepared flue gas with temperature around 150°C was
processed in designed laboratory O-element scrubber. Water was
used as absorbent liquid. The efficiency of SO2 removal, pressure
drop and temperature drop were measured on our experimental
device. The dependence of these variables on liquid-gas ratio was
observed. The average temperature drop was in the range from
150°C to 40°C. The pressure drop was increased with increasing of
a liquid-gas ratio, but no too much as for the common venturi
scrubber designs. The efficiency of SO2 removal was up to 70 %.
The pressure drop of our new designed wet scrubber is similar to
commonly used venturi scrubbers; nevertheless the influence of
amount of the liquid on pressure drop is not so significant.
Abstract: Early diagnosis of infection like Hep-B virus in blood
is important for low cost medical treatment. For this purpose, it is
desirable to develop a point of care device which should be able to
detect trace quantities of the target molecule in blood. In this paper,
we report a nanoporous silicon oxide sensor which is capable of
detecting down to 1fM concentration of Hep-B surface antigen in
blood without the requirement of any centrifuge or pre-concentration.
This has been made possible by the presence of resonant peak in the
sensitivity characteristics. This peak is observed to be dependent only
on the concentration of the specific antigen and not on the interfering
species in blood serum. The occurrence of opposite impedance
change within the pores and at the bottom of the pore is responsible
for this effect. An electronic interface has also been designed to
provide a display of the virus concentration.
Abstract: This paper presents the design and fabrication of an
optical window for an optical modulator toward image sensing
applications. An optical window consists of micrometer-order SiO2
capillaries (porous solid) that can modulate transmission light
intensity by moving the liquid in and out of porous solid. A high
optical transmittance of the optical window can be achieved due to
refractive index matching when the liquid is penetrated into the
porous solid. Otherwise, its light transmittance is lower because of
light reflection and scattering by air holes and capillary walls. Silicon
capillaries fabricated by deep reactive ion etching (DRIE) process are
completely oxidized to form the SiO2 capillaries. Therefore, high
aspect ratio SiO2 capillaries can be achieved based on silicon
capillaries formed by DRIE technique. Large compressive stress of
the oxide causes bending of the capillary structure, which is reduced
by optimizing the design of device structure. The large stress of the
optical window can be released via thin supporting beams. A 7.2 mm
x 9.6 mm optical window area toward a fully integrated with the
image sensor format is successfully fabricated and its optical
transmittance is evaluated with and without inserting liquids (ethanol
and matching oil). The achieved modulation range is approximately
20% to 35% with and without liquid penetration in visible region
(wavelength range from 450 nm to 650 nm).
Abstract: The capability of exploiting the electronic charge and
spin properties simultaneously in a single material has made diluted
magnetic semiconductors (DMS) remarkable in the field of
spintronics. We report the designing of DMS based on zinc-blend
ZnO doped with Cr impurity. The full potential linearized augmented
plane wave plus local orbital FP-L(APW+lo) method in density
functional theory (DFT) has been adapted to carry out these
investigations. For treatment of exchange and correlation energy,
generalized gradient approximations have been used. Introducing Cr
atoms in the matrix of ZnO has induced strong magnetic moment
with ferromagnetic ordering at stable ground state. Cr:ZnO was found
to favor the short range magnetic interaction that
reflect tendency of Cr clustering. The electronic structure of ZnO is
strongly influenced in the presence of Cr impurity atoms where
impurity bands appear in the band gap.
Abstract: The quality and condition of perishable products
delivered to the market and their subsequent selling prices are
directly affected by the care taken during harvesting and handling.
Mechanical injury, in fact, occurs at all stages, from pre-harvest
operations through post-harvest handling, packing and transport to
the market. The main implications of this damage are the reduction of
the product’s quality and economical losses related to the shelf life
diminution. For most perishable products, the shelf life is relatively
short and it is typically dictated by microbial growth related to the
application of dynamic and static loads during transportation. This
paper presents the correlation between vibration levels and
microbiological growth on strawberries and woodland strawberries
and detects the presence of volatile organic compounds (VOC) in
order to develop an intelligent logistic unit capable of monitoring
VOCs using a specific sensor system. Fresh fruits were exposed to
vibrations by means of a vibrating table in a temperature-controlled
environment. Microbiological analyses were conducted on samples,
taken at different positions along the column of the crates. The values
obtained were compared with control samples not exposed to
vibrations and the results show that different positions along the
column influence the development of bacteria, yeasts and filamentous
fungi.
Abstract: Alone with fast urbanization in world, traffic control
became a big issue in urban construction. Having an efficient and
reliable traffic control system is crucial to macro-traffic control.
Traffic signal is used to manage conflicting requirement by allocating
different sets of mutually compatible traffic movement during distinct
time interval. Many approaches have been made proposed to solve
this discrete stochastic problem. Recognizing the need to minimize
right-of-way impacts while efficiently handling the anticipated high
traffic volumes, the proposed alternative system gives effective
design. This model allows for increased traffic capacity and reduces
delays by eliminating a step in maneuvering through the freeway
interchange. The concept proposed in this paper involves
construction of bridges and ramps at intersection of four roads to
control the vehicular congestion and to prevent traffic breakdown.