Abstract: The development of renewable energies - particularly energy from wind, water, solar power and biomass - is a central aim of the European Commission's energy policy. There are several reasons for this choice: renewable energies are sustainable, nonpolluting, widely available and clean. Increasing the share of renewable energy in the energy balance enhances sustainability. It also helps to improve the security of energy supply by reducing the Community's growing dependence on imported energy sources.In this paper it was studied the possibility to realize three photovoltaic systems in the Italian Natural Park “Gola della Rossa e di Frasassi". The first photovoltaic system is a grid-connected system for Services and Documentation Center of Castelletta with a nominal power of about 6 kWp. The second photovoltaic system is a grid-connected integrated system on the ticket office-s roof with a nominal power of about 4 kWp. The third project is set up by five grid-connected systems integrated on the roofs of the bungalows in Natural Park-s tourist camping with a nominal power of about 10 kWp. The electricity which is generated by all these plants is purchased according to the Italian program called “Conto Energia". Economical analysis and the amount of the avoided CO2 emissions are elaborated for these photovoltaic systems.
Abstract: Dense slurry flow through centrifugal pump casing
has been modeled using the Eulerian-Eulerian approach with
Eulerian multiphase model in FLUENT 6.1®. First order upwinding
is considered for the discretization of momentum, k and ε terms.
SIMPLE algorithm has been applied for dealing with pressurevelocity
coupling. A mixture property based k-ε turbulence model
has been used for modeling turbulence. Results are validated first
against mesh independence and experiments for a particular set of
operational and geometric conditions. Parametric analysis is then
performed to determine the effect on important physical quantities
viz. solid velocities, solid concentration and solid stresses near the
wall with various operational geometric conditions of the pump.
Abstract: Understanding proteins functions is a major goal in
the post-genomic era. Proteins usually work in context of other
proteins and rarely function alone. Therefore, it is highly relevant to
study the interaction partners of a protein in order to understand its
function. Machine learning techniques have been widely applied to
predict protein-protein interactions. Kernel functions play an
important role for a successful machine learning technique. Choosing
the appropriate kernel function can lead to a better accuracy in a
binary classifier such as the support vector machines. In this paper,
we describe a Bayesian kernel for the support vector machine to
predict protein-protein interactions. The use of Bayesian kernel can
improve the classifier performance by incorporating the probability
characteristic of the available experimental protein-protein
interactions data that were compiled from different sources. In
addition, the probabilistic output from the Bayesian kernel can assist
biologists to conduct more research on the highly predicted
interactions. The results show that the accuracy of the classifier has
been improved using the Bayesian kernel compared to the standard
SVM kernels. These results imply that protein-protein interaction can
be predicted using Bayesian kernel with better accuracy compared to
the standard SVM kernels.
Abstract: State-based testing is frequently used in software testing. Test data generation is one of the key issues in software testing. A properly generated test suite may not only locate the errors in a software system, but also help in reducing the high cost associated with software testing. It is often desired that test data in the form of test sequences within a test suite can be automatically generated to achieve required test coverage. This paper proposes an Ant Colony Optimization approach to test data generation for the state-based software testing.
Abstract: This paper presents methodologies for developing an
intelligent CAD system assisting in analysis and design of
reconfigurable special machines. It describes a procedure for
determining feasibility of utilizing these machines for a given part
and presents a model for developing an intelligent CAD system. The
system analyzes geometrical and topological information of the given
part to determine possibility of the part being produced by
reconfigurable special machines from a technical point of view. Also
feasibility of the process from a economical point of view is
analyzed. Then the system determines proper positioning of the part
considering details of machining features and operations needed.
This involves determination of operation types, cutting tools and the
number of working stations needed. Upon completion of this stage
the overall layout of the machine and machining equipment required
are determined.
Abstract: Graphene-metal contact resistance limits the performance of graphene-based electrical devices. In this work, we have fabricated both graphene field-effect transistors (GFET) and transfer length measurement (TLM) test devices with titanium contacts. The purpose of this work is to compare the contact resistances that can be numerically extracted from the GFETs and measured from the TLM structures. We also provide a brief review of the work done in the field to solve the contact resistance problem.
Abstract: Using a texture database, a statistical estimation of
spring-back was conducted in this study on the basis of statistical
analysis. Both spring-back in bending deformation and experimental
data related to the crystal orientation show significant dispersion.
Therefore, a probabilistic statistical approach was established for the
proper quantification of these values. Correlation was examined
among the parameters F(x) of spring-back, F(x) of the buildup fraction
to three orientations after 92° bending, and F(x) at an as-received part
on the basis of the three-parameter Weibull distribution. Consequent
spring-back estimation using a texture database yielded excellent
estimates compared with experimental values.
Abstract: The European countries that during the past two
decades based their exchange rate regimes on currency board
arrangement (CBA) are usually analysed from the perspective of
corner solution choice’s stabilisation effects. There is an open
discussion on the positive and negative background of a strict
exchange rate regime choice, although it should be seen as part of the
transition process towards the monetary union membership. The
focus of the paper is on the Baltic countries that after two decades of
a rigid exchange rate arrangement and strongly influenced by global
crisis are finishing their path towards the euro zone. Besides the
stabilising capacity, the CBA is highly vulnerable regime, with
limited developing potential. The rigidity of the exchange rate (and
monetary) system, despite the ensured credibility, do not leave
enough (or any) space for the adjustment and/or active crisis
management. Still, the Baltics are in a process of recovery, with fiscal
consolidation measures combined with (painful and politically
unpopular) measures of internal devaluation. Today, two of them
(Estonia and Latvia) are members of euro zone, fulfilling their
ultimate transition targets, but de facto exchanging one fixed regime
with another.
The paper analyses the challenges for the CBA in unstable
environment since the fixed regimes rely on imported stability and
are sensitive to external shocks. With limited monetary instruments,
these countries were oriented to the fiscal policies and used a
combination of internal devaluation and tax policy measures. Despite
their rather quick recovery, our second goal is to analyse the long
term influence that the measures had on the national economy.
Abstract: For high-speed control of robots, a good knowledge of system modelling is necessary to obtain the desired bandwidth. In this paper, we present a cartesian robot with a pan/tilt unit in end-effector (5 dof). This robot is implemented with powerful direct drive AC induction machines. The dynamic model, parameter identification and model validation of the robot are studied (including actuators). This work considers the cartesian robot coupled and non linear (contrary to normal considerations for this type of robots). The mechanical and control architecture proposed in this paper is efficient for industrial and research application in which high speed, well known model and very high accuracy are required.
Abstract: System identification is the process of creating
models of dynamic process from input- output signals. The aim of
system identification can be identified as “ to find a model with
adjustable parameters and then to adjust them so that the predicted
output matches the measured output". This paper presents a method
of modeling and simulating with system identification to achieve the
maximum fitness for transformation function. First by using
optimized KLM equivalent circuit for PVDF piezoelectric transducer
and assuming different inputs including: sinuside, step and sum of
sinusides, get the outputs, then by using system identification
toolbox in MATLAB, we estimate the transformation function from
inputs and outputs resulted in last program. Then compare the fitness
of transformation function resulted from using ARX,OE(Output-
Error) and BJ(Box-Jenkins) models in system identification toolbox
and primary transformation function form KLM equivalent circuit.
Abstract: One of the most common practices for strengthening
the reinforced concrete structures is the application of FRP (Fiber
Reinforce Plastic) sheets to increase the flexural and shear strengths
of the member. The elastic modulus of FRP is considerably higher
than that of concrete. This will result in debonding between the FRP
sheets and concrete surface. With conventional surface preparation of
concrete, the ultimate capacity of the FRP sheets can hardly be
achieved. New methods for preparation of the bonding surface have
shown improvements in reducing the premature debonding of FRP
sheets from concrete surface. The present experimental study focuses
on the application of grooving method to postpone debonding of the
FRP sheets attached to the side faces of concrete beams for shear
strengthening. Comparison has also been made with conventional
surface preparation method. This study clearly shows the efficiency
of grooving method compared to surface preparation method, in
preventing the debonding phenomenon and in increasing the load
carrying capacity of FRP.
Abstract: Fast forecasting of stock market prices is very important for
strategic planning. In this paper, a new approach for fast forecasting of
stock market prices is presented. Such algorithm uses new high speed
time delay neural networks (HSTDNNs). The operation of these
networks relies on performing cross correlation in the frequency
domain between the input data and the input weights of neural
networks. It is proved mathematically and practically that the number
of computation steps required for the presented HSTDNNs is less
than that needed by traditional time delay neural networks
(TTDNNs). Simulation results using MATLAB confirm the
theoretical computations.
Abstract: In recent years, the research in wireless sensor
network has increased steadily, and many studies were focusing on
reducing energy consumption of sensor nodes to extend their lifetimes.
In this paper, the issue of energy consumption is investigated and two
adaptive mechanisms are proposed to extend the network lifetime.
This study uses high-energy-first scheme to determine cluster heads
for data transmission. Thus, energy consumption in each cluster is
balanced and network lifetime can be extended. In addition, this study
uses cluster merging and dynamic routing mechanisms to further
reduce energy consumption during data transmission. The simulation
results show that the proposed method can effectively extend the
lifetime of wireless sensor network, and it is suitable for different base
station locations.
Abstract: In the present study, changes of morphology and
mechanical characteristics in the lumbar vertebrae of the
ovariectomised (OVX) rat were investigated. In previous researches,
there were many studies about morphology like volume fraction and
trabecular thickness based on Micro - Computed Tomography (Micro
- CT). However, detecting and tracking long-term changes in the
trabecular bone of the lumbar vertebrae for the OVX rat were few. For
this study, one female Sprague-Dawley rat was used: an OVX rat. The
4th Lumbar of the OVX rat was subjected to in-vivo micro-CT.
Detecting and tracking long-term changes could be investigated in the
trabecular bone of the lumbar vertebrae for an OVX rat using in-vivo
micro-CT. An OVX rat was scanned at week 0 (just before surgery), at
week 4, at week 8, week 16, week 22 and week 56 after surgery. Finite
element (FE) analysis was used to investigate mechanical
characteristics of the lumbar vertebrae for an OVX rat. When the OVX
rat (at week 56) was compared with the OVX rat (at week 0), volume
fraction was decreased by 80% and effective modulus was decreased
by 75%.
Abstract: An experimental and numerical study has been conducted to clarify heat transfer characteristics and effectiveness of a cross-flow heat exchanger employing staggered wing-shaped tubes at different angels of attack. The water-side Rew and the air-side Rea were at 5 x 102 and at from 1.8 x 103 to 9.7 x 103, respectively. The tubes arrangements were employed with various angles of attack θ1,2,3 from 0° to 330° at the considered Rea range. Correlation of Nu, St, as well as the heat transfer per unit pumping power (ε) in terms of Rea, design parameters for the studied bundle were presented. The temperature fields around the staggered wing-shaped tubes bundle were predicted by using commercial CFD FLUENT 6.3.26 software package. Results indicated that the heat transfer was increased by increasing the angle of attack from 0° to 45°, while the opposite was true for angles of attack from 135° to 180°. The best thermal performance and hence η of studied bundle was occurred at the lowest Rea and/or zero angle of attack. Comparisons between the experimental and numerical results of the present study and those, previously, obtained for similar available studies showed good agreements.
Abstract: We consider optimal channel equalization for MIMO
(multi-input/multi-output) time-varying channels in the sense of
MMSE (minimum mean-squared-error), where the observation noise
can be non-stationary. We show that all ZF (zero-forcing) receivers
can be parameterized in an affine form which eliminates completely
the ISI (inter-symbol-interference), and optimal channel equalizers
can be designed through minimization of the MSE (mean-squarederror)
between the detected signals and the transmitted signals,
among all ZF receivers. We demonstrate that the optimal channel
equalizer is a modified Kalman filter, and show that under the AWGN
(additive white Gaussian noise) assumption, the proposed optimal
channel equalizer minimizes the BER (bit error rate) among all
possible ZF receivers. Our results are applicable to optimal channel
equalization for DWMT (discrete wavelet multitone), multirate transmultiplexers,
OFDM (orthogonal frequency division multiplexing),
and DS (direct sequence) CDMA (code division multiple access)
wireless data communication systems. A design algorithm for optimal
channel equalization is developed, and several simulation examples
are worked out to illustrate the proposed design algorithm.
Abstract: This paper describes studies carried out to investigate
the viability of using wireless cameras as a tool in monitoring
changes in air quality. A camera is used to monitor the change in
colour of a chemically responsive polymer within view of the camera
as it is exposed to varying chemical species concentration levels. The
camera captures this image and the colour change is analyzed by
averaging the RGB values present. This novel chemical sensing
approach is compared with an established chemical sensing method
using the same chemically responsive polymer coated onto LEDs. In
this way, the concentration levels of acetic acid in the air can be
tracked using both approaches. These approaches to chemical plume
tracking have many applications for air quality monitoring.
Abstract: ZnO heteronanostructured nanowires arrays have
been fabricated by low temperature solution method. Various
heterostructures were synthesized including CdS/ZnO,
CdSe/CdS/ZnO nanowires and Co3O4/ZnO, ZnO/SiC
nanowires. These multifunctional heterostructure nanowires
showed important applications in photocatalysts, sensors,
wettability control and solar energy conversion.
Abstract: An enhanced particle swarm optimization algorithm
(PSO) is presented in this work to solve the non-convex OPF
problem that has both discrete and continuous optimization variables.
The objective functions considered are the conventional quadratic
function and the augmented quadratic function. The latter model
presents non-differentiable and non-convex regions that challenge
most gradient-based optimization algorithms. The optimization
variables to be optimized are the generator real power outputs and
voltage magnitudes, discrete transformer tap settings, and discrete
reactive power injections due to capacitor banks. The set of equality
constraints taken into account are the power flow equations while the
inequality ones are the limits of the real and reactive power of the
generators, voltage magnitude at each bus, transformer tap settings,
and capacitor banks reactive power injections. The proposed
algorithm combines PSO with Newton-Raphson algorithm to
minimize the fuel cost function. The IEEE 30-bus system with six
generating units is used to test the proposed algorithm. Several cases
were investigated to test and validate the consistency of detecting
optimal or near optimal solution for each objective. Results are
compared to solutions obtained using sequential quadratic
programming and Genetic Algorithms.
Abstract: Development of artificial neural network (ANN) for
prediction of aluminum workpieces' surface roughness in ultrasonicvibration
assisted turning (UAT) has been the subject of the present
study. Tool wear as the main cause of surface roughness was also
investigated. ANN was trained through experimental data obtained
on the basis of full factorial design of experiments. Various
influential machining parameters were taken into consideration. It
was illustrated that a multilayer perceptron neural network could
efficiently model the surface roughness as the response of the
network, with an error less than ten percent. The performance of the
trained network was verified by further experiments. The results of
UAT were compared with the results of conventional turning
experiments carried out with similar machining parameters except for
the vibration amplitude whence considerable reduction was observed
in the built-up edge and the surface roughness.