Abstract: In the present study, a steady-state simulation model
has been developed to evaluate the system performance of a
transcritical carbon dioxide heat pump system for simultaneous water
cooling and heating. Both the evaporator (including both two-phase
and superheated zone) and gas cooler models consider the highly
variable heat transfer characteristics of CO2 and pressure drop. The
numerical simulation model of transcritical CO2 heat pump has been
validated by test data obtained from experiments on the heat pump
prototype. Comparison between the test results and the model
prediction for system COP variation with compressor discharge
pressure shows a modest agreement with a maximum deviation of
15% and the trends are fairly similar. Comparison for other operating
parameters also shows fairly similar deviation between the test
results and the model prediction. Finally, the simulation results are
presented to study the effects of operating parameters such as,
temperature of heat exchanger fluid at the inlet, discharge pressure,
compressor speed on system performance of CO2 heat pump, suitable
in a dairy plant where simultaneous cooling at 4oC and heating at
73oC are required. Results show that good heat transfer properties of
CO2 for both two-phase and supercritical region and efficient
compression process contribute a lot for high system COPs.
Abstract: In this paper, the Lennard -Jones potential is applied
to molecules of liquid argon as well as its vapor and platinum as solid
surface in order to perform a non-equilibrium molecular dynamics
simulation to study the microscopic aspects of liquid-vapor-solid
interactions. The channel is periodic in x and y directions and along z
direction it is bounded by atomic walls. It was found that density of
the liquids near the solid walls fluctuated greatly and that the
structure was more like a solid than a liquid. This indicates that the
interactions of solid and liquid molecules are very strong. The
resultant surface tension, liquid density and vapor density are found
to be well predicted when compared with the experimental data for
argon. Liquid and vapor densities were found to depend on the cutoff
radius which induces the use of P3M (particle-particle particle-mesh)
method which was implemented for evaluation of force and surface
tension.
Abstract: Reliable information about tool temperature
distribution is of central importance in metal cutting. In this study,
tool-chip interface temperature was determined in cutting of ST37
steel workpiece by applying HSS as the cutting tool in dry turning.
Two different approaches were implemented for temperature
measuring: an embedded thermocouple (RTD) in to the cutting tool
and infrared (IR) camera. Comparisons are made between
experimental data and results of MSC.SuperForm and FLUENT
software.
An investigation of heat generation in cutting tool was performed
by varying cutting parameters at the stable cutting tool geometry and
results were saved in a computer; then the diagrams of tool
temperature vs. various cutting parameters were obtained. The
experimental results reveal that the main factors of the increasing
cutting temperature are cutting speed (V ), feed rate ( S ) and depth
of cut ( h ), respectively. It was also determined that simultaneously
change in cutting speed and feed rate has the maximum effect on
increasing cutting temperature.
Abstract: This paper gives a novel method for improving
classification performance for cancer classification with very few
microarray Gene expression data. The method employs classification
with individual gene ranking and gene subset ranking. For selection
and classification, the proposed method uses the same classifier. The
method is applied to three publicly available cancer gene expression
datasets from Lymphoma, Liver and Leukaemia datasets. Three
different classifiers namely Support vector machines-one against all
(SVM-OAA), K nearest neighbour (KNN) and Linear Discriminant
analysis (LDA) were tested and the results indicate the improvement
in performance of SVM-OAA classifier with satisfactory results on
all the three datasets when compared with the other two classifiers.
Abstract: this paper presented a survey analysis subjected on
network bandwidth management from published papers referred in
IEEE Explorer database in three years from 2009 to 2011. Network
Bandwidth Management is discussed in today-s issues for computer
engineering applications and systems. Detailed comparison is
presented between published papers to look further in the IP based
network critical research area for network bandwidth management.
Important information such as the network focus area, a few
modeling in the IP Based Network and filtering or scheduling used in
the network applications layer is presented. Many researches on
bandwidth management have been done in the broad network area
but fewer are done in IP Based network specifically at the
applications network layer. A few researches has contributed new
scheme or enhanced modeling but still the issue of bandwidth
management still arise at the applications network layer. This survey
is taken as a basic research towards implementations of network
bandwidth management technique, new framework model and
scheduling scheme or algorithm in an IP Based network which will
focus in a control bandwidth mechanism in prioritizing the network
traffic the applications layer.
Abstract: This paper proposes a declarative language for
knowledge representation (Ibn Rochd), and its environment of
exploitation (DeGSE). This DeGSE system was designed and
developed to facilitate Ibn Rochd writing applications. The system
was tested on several knowledge bases by ascending complexity,
culminating in a system for recognition of a plant or a tree, and
advisors to purchase a car, for pedagogical and academic guidance,
or for bank savings and credit. Finally, the limits of the language and
research perspectives are stated.
Abstract: The most reliable and accurate description of the actual behavior of a software system is its source code. However, not all questions about the system can be answered directly by resorting to this repository of information. What the reverse engineering methodology aims at is the extraction of abstract, goal-oriented “views" of the system, able to summarize relevant properties of the computation performed by the program. While concentrating on reverse engineering we had modeled the C++ files by designing the translator.
Abstract: A New features are extracted and compared to
improve the prediction of protein-protein interactions. The basic idea
is to select and use the best set of features from the Tensor matrices
that are produced by the frequency vectors of the protein sequences.
Three set of features are compared, the first set is based on the
indices that are the most common in the interacting proteins, the
second set is based on the indices that tend to be common in the
interacting and non-interacting proteins, and the third set is
constructed by using random indices. Moreover, three encoding
strategies are compared; that are based on the amino asides polarity,
structure, and chemical properties. The experimental results indicate
that the highest accuracy can be obtained by using random indices
with chemical properties encoding strategy and support vector
machine.
Abstract: Nowadays use of a new structural bracing system
called 'Knee Bracing System' have taken the specialists attention too
much. On the other hand nonlinear static analysis procedures in
estimate structures performance in earthquake time have taken
attention too much. One of these procedure is modal pushover
analysis (MPA) procedure. The accuracy of MPA procedure for
simple steel moment resisting frame has been verified and considered
in Chintanapakdee and Chopra-s article in 2003. Since the accuracy
of MPA procedure has not verified for semi-rigid steel frames with
knee bracing, we are going to get through with this matter in this
study. For this purpose, the selected structures are four frames with
different heights, 5 to 20 stories, will be designed according to AISC
criteria. Then MPA procedure is used for the same frames with
different rigidity percentiles of connections. The results of seismic
responses are compared with dynamic nonlinear response history
analysis as exact procedure and accuracy of MPA procedure is
evaluated. It seems that MPA procedure accuracy will come down by
reduction of the rigidity percentiles of semi-rigid connections.
Abstract: This paper addresses one of the most important issues
have been considered in hybrid MTS/MTO production environments. To cope with the problem, a mathematical programming model is
applied from a tactical point of view. The model is converted to a fuzzy goal programming model, because a degree of uncertainty is involved in hybrid MTS/MTO context. Finally, application of the
proposed model in an industrial center is reported and the results prove the validity of the model.
Abstract: The purpose of this study was to investigate the
relationships among students- process of study, creative self-efficacy
and creativity while attending college. A total of 60 students enrolled
in Hsiuping Institute of Technology in central Taiwan were selected as
samples for the study. The instruments for this study included three
questionnaires to explore the aforesaid aspects.
This researchers tested creative self-efficacy and process of study,
and creativity with Pearson correlation and hierarchical regression
analyses. The major findings of this research are (1) the process of
study had direct positive predictability on creativity, and (2) the
relationship between process of study and creativity is partially
mediated by creative self-efficacy.
Abstract: A parallel computational fluid dynamics code has been
developed for the study of aerodynamic heating problem in hypersonic
flows. The code employs the 3D Navier-Stokes equations as the basic
governing equations to simulate the laminar hypersonic flow. The cell
centered finite volume method based on structured grid is applied for
spatial discretization. The AUSMPW+ scheme is used for the inviscid
fluxes, and the MUSCL approach is used for higher order spatial
accuracy. The implicit LU-SGS scheme is applied for time integration
to accelerate the convergence of computations in steady flows. A
parallel programming method based on MPI is employed to shorten
the computing time. The validity of the code is demonstrated by
comparing the numerical calculation result with the experimental data
of a hypersonic flow field around a blunt body.
Abstract: This paper investigates the performance of a speech
recognizer in an interactive voice response system for various coded
speech signals, coded by using a vector quantization technique namely
Multi Switched Split Vector Quantization Technique. The process of
recognizing the coded output can be used in Voice banking application.
The recognition technique used for the recognition of the coded speech
signals is the Hidden Markov Model technique. The spectral distortion
performance, computational complexity, and memory requirements of
Multi Switched Split Vector Quantization Technique and the
performance of the speech recognizer at various bit rates have been
computed. From results it is found that the speech recognizer is
showing better performance at 24 bits/frame and it is found that the
percentage of recognition is being varied from 100% to 93.33% for
various bit rates.
Abstract: This report shows the performance of composite
biodegradable film from chitosan, starch and sawdust fiber. The main
objectives of this research are to fabricate and characterize composite
biodegradable film in terms of morphology and physical properties.
The film was prepared by casting method. Sawdust fiber was used as
reinforcing agent and starch as polymer matrix in the casting
solution. The morphology of the film was characterized using atomic
force microscope (AFM). The result showed that the film has
smooth structure. Chemical composition of the film was investigated
using Fourier transform infrared (FTIR) where the result revealed
present of starch in the film. The thermal properties were
characterized using thermal gravimetric analyzer (TGA) and
differential scanning calorimetric (DSC) where the results showed
that the film has small difference in melting and degradation
temperature.
Abstract: In order to reduce cost, increase quality, and for
timely supplying production systems has considerably taken the
advantages of supply chain management and these advantages are
also competitive. Selection of appropriate supplier has an important
role in improvement and efficiency of systems.
The models of supplier selection which have already been used by
researchers have considered selection one or more suppliers from
potential suppliers but in this paper selecting one supplier as partner
from one supplier that have minimum one period supplying to buyer
is considered.
This paper presents a conceptual model for partner selection and
application of Degree of Adoptive (DOA) model for final selection.
The attributes weight in this model is prepared through AHP
model. After making the descriptive model, determining the
attributes and measuring the parameters of the adaptive is examined
in an auto industry of Iran(Zagross Khodro co.) and results are
presented.
Abstract: Adaptive Genetic Algorithms extend the Standard Gas
to use dynamic procedures to apply evolutionary operators such as
crossover, mutation and selection. In this paper, we try to propose a
new adaptive genetic algorithm, which is based on the statistical
information of the population as a guideline to tune its crossover,
selection and mutation operators. This algorithms is called Statistical
Genetic Algorithm and is compared with traditional GA in some
benchmark problems.
Abstract: In this research work, investigations are carried out on
Continuous Wave (CW) Nd:YAG laser welding system after
preliminary experimentation to understand the influencing parameters
associated with laser welding of AISI 304. The experimental
procedure involves a series of laser welding trials on AISI 304
stainless steel sheets with various combinations of process parameters
like beam power, beam incident angle and beam incident angle. An
industrial 2 kW CW Nd:YAG laser system, available at Welding
Research Institute (WRI), BHEL Tiruchirappalli, is used for
conducting the welding trials for this research. After proper tuning of
laser beam, laser welding experiments are conducted on AISI 304
grade sheets to evaluate the influence of various input parameters on
weld bead geometry i.e. bead width (BW) and depth of penetration
(DOP). From the laser welding results, it is noticed that the beam
power and welding speed are the two influencing parameters on
depth and width of the bead. Three dimensional finite element
simulation of high density heat source have been performed for laser
welding technique using finite element code ANSYS for predicting
the temperature profile of laser beam heat source on AISI 304
stainless steel sheets. The temperature dependent material properties
for AISI 304 stainless steel are taken into account in the simulation,
which has a great influence in computing the temperature profiles.
The latent heat of fusion is considered by the thermal enthalpy of
material for calculation of phase transition problem. A Gaussian
distribution of heat flux using a moving heat source with a conical
shape is used for analyzing the temperature profiles. Experimental
and simulated values for weld bead profiles are analyzed for stainless
steel material for different beam power, welding speed and beam
incident angle. The results obtained from the simulation are
compared with those from the experimental data and it is observed
that the results of numerical analysis (FEM) are in good agreement
with experimental results, with an overall percentage of error
estimated to be within ±6%.
Abstract: This paper describes an efficient hardware implementation of a new technique for interfacing the data exchange between the microprocessor-based systems and the external devices. This technique, based on the use of software/hardware system and a reduced physical address, enlarges the interfacing capacity of the microprocessor-based systems, uses the Direct Memory Access (DMA) to increases the frequency of the new bus, and improves the speed of data exchange. While using this architecture in microprocessor-based system or in computer, the input of the hardware part of our system will be connected to the bus system, and the output, which is a new bus, will be connected to an external device. The new bus is composed of a data bus, a control bus and an address bus. A Xilinx Integrated Software Environment (ISE) 7.1i has been used for the programmable logic implementation.
Abstract: Data mining (DM) is the process of finding and extracting frequent patterns that can describe the data, or predict unknown or future values. These goals are achieved by using various learning algorithms. Each algorithm may produce a mining result completely different from the others. Some algorithms may find millions of patterns. It is thus the difficult job for data analysts to select appropriate models and interpret the discovered knowledge. In this paper, we describe a framework of an intelligent and complete data mining system called SUT-Miner. Our system is comprised of a full complement of major DM algorithms, pre-DM and post-DM functionalities. It is the post-DM packages that ease the DM deployment for business intelligence applications.
Abstract: Nowadays, several techniques such as; Fuzzy
Inference System (FIS) and Neural Network (NN) are employed for
developing of the predictive models to estimate parameters of water
quality. The main objective of this study is to compare between the
predictive ability of the Adaptive Neuro-Fuzzy Inference System
(ANFIS) model and Artificial Neural Network (ANN) model to
estimate the Biochemical Oxygen Demand (BOD) on data from 11
sampling sites of Saen Saep canal in Bangkok, Thailand. The data is
obtained from the Department of Drainage and Sewerage, Bangkok
Metropolitan Administration, during 2004-2011. The five parameters
of water quality namely Dissolved Oxygen (DO), Chemical Oxygen
Demand (COD), Ammonia Nitrogen (NH3N), Nitrate Nitrogen
(NO3N), and Total Coliform bacteria (T-coliform) are used as the
input of the models. These water quality indices affect the
biochemical oxygen demand. The experimental results indicate that
the ANN model provides a higher correlation coefficient (R=0.73)
and a lower root mean square error (RMSE=4.53) than the
corresponding ANFIS model.