Abstract: An Acoustic Micro-Energy Harvester (AMEH) is
developed to convert wasted acoustical energy into useful electrical
energy. AMEH is mathematically modeled using Lumped Element
Modelling (LEM) and Euler-Bernoulli beam (EBB) modelling. An
experiment is designed to validate the mathematical model and assess
the feasibility of AMEH. Comparison of theoretical and experimental
data on critical parameter value such as Mm, Cms, dm and Ceb showed
the variances are within 1% to 6%, which is reasonably acceptable.
Then, AMEH undergoes bandwidth tuning for performance
optimization. The AMEH successfully produces 0.9V/(m/s^2) and
1.79μW/(m^2/s^4) at 60Hz and 400kΩ resistive load which only
show variances about 7% compared to theoretical data. At 1g and
60Hz resonance frequency, the averaged power output is about
2.2mW which fulfilled a range of wireless sensors and
communication peripherals power requirements. Finally, the design
for AMEH is assessed, validated and deemed as a feasible design.
Abstract: This study investigates the effects of the lead angle
and chip thickness variation on surface roughness during the
machining of compacted graphite iron using ceramic cutting tools
under dry cutting conditions. Analytical models were developed for
predicting the surface roughness values of the specimens after the
face milling process. Experimental data was collected and imported
to the artificial neural network model. A multilayer perceptron model
was used with the back propagation algorithm employing the input
parameters of lead angle, cutting speed and feed rate in connection
with chip thickness. Furthermore, analysis of variance was employed
to determine the effects of the cutting parameters on surface
roughness. Artificial neural network and regression analysis were
used to predict surface roughness. The values thus predicted were
compared with the collected experimental data, and the
corresponding percentage error was computed. Analysis results
revealed that the lead angle is the dominant factor affecting surface
roughness. Experimental results indicated an improvement in the
surface roughness value with decreasing lead angle value from 88° to
45°.
Abstract: Several parameters are established in order to measure
biodiesel quality. One of them is the iodine value, which is an
important parameter that measures the total unsaturation within a
mixture of fatty acids. Limitation of unsaturated fatty acids is
necessary since warming of higher quantity of these ones ends in
either formation of deposits inside the motor or damage of lubricant.
Determination of iodine value by official procedure tends to be very
laborious, with high costs and toxicity of the reagents, this study uses
artificial neural network (ANN) in order to predict the iodine value
property as an alternative to these problems. The methodology of
development of networks used 13 esters of fatty acids in the input
with convergence algorithms of back propagation of back
propagation type were optimized in order to get an architecture of
prediction of iodine value. This study allowed us to demonstrate the
neural networks’ ability to learn the correlation between biodiesel
quality properties, in this caseiodine value, and the molecular
structures that make it up. The model developed in the study reached
a correlation coefficient (R) of 0.99 for both network validation and
network simulation, with Levenberg-Maquardt algorithm.
Abstract: In this work new macroporous Ni electrodes modified
with Au nanoparticles for hydrogen production have been developed.
The supporting macroporous Ni electrodes have been obtained by
means of the electrodeposition at high current densities. Then, the Au
nanoparticles were synthesized and added to the electrode surface.
The electrocatalytic behaviour of the developed electrocatalysts was
studied by means of pseudo-steady-state polarization curves,
electrochemical impedance spectroscopy (EIS) and hydrogen
discharge curves. The size of the Au synthetized nanoparticles shows
a monomodal distribution, with a very sharp band between 10 and 50
nm. The characteristic parameters d10, d50 and d90 were 14, 20 and
31 nm respectively. From Tafel polarization data has been concluded
that the Au nanoparticles improve the catalytic activity of the
developed electrodes towards the HER respect to the macroporous Ni
electrodes. EIS permits to obtain the electrochemically active area by
means of the roughness factor value. All the developed electrodes
show roughness factor values in the same order of magnitude. From
the activation energy results it can be concluded that the Au
nanoparticles improve the intrinsic catalytic activity of the
macroporous Ni electrodes.
Abstract: Most of the oil palm plantations have been threatened
by Basal Stem Rot (BSR) disease which causes serious economic
impact. This study was conducted to identify the healthy and BSRinfected
oil palm tree using thirteen color indices. Multispectral and
thermal camera was used to capture 216 images of the leaves taken
from frond number 1, 9 and 17. Indices of normalized difference
vegetation index (NDVI), red (R), green (G), blue (B), near infrared
(NIR), green – blue (GB), green/blue (G/B), green – red (GR),
green/red (G/R), hue (H), saturation (S), intensity (I) and thermal
index (T) were used. From this study, it can be concluded that G
index taken from frond number 9 is the best index to differentiate
between the healthy and BSR-infected oil palm trees. It not only gave
high value of correlation coefficient (R=-0.962), but also high value
of separation between healthy and BSR-infected oil palm tree.
Furthermore, power and S model developed using G index gave the
highest R2 value which is 0.985.
Abstract: One of the functions of the commercial heavy vehicle
is to safely and efficiently transport goods and people. Due to its size
and carrying capacity, it is important to study the vehicle dynamic
stability during cornering. Study has shown that there are a number of
overloaded heavy vehicles or permissible Gross Vehicle Weight
(GVW) violations recorded at selected areas in Malaysia assigned by
its type and category. Thus, the objective of this study is to
investigate the correlation and effect of the GVW on heavy vehicle
stability during cornering event using simulation. Various selected
heavy vehicle types and category are simulated using IPG/Truck
Maker® with different GVW and road condition (coefficient of
friction of road surface), while the speed, driver characteristic, center
of gravity of load and road geometry are constant. Based on the
analysis, the relationship between GVW and lateral acceleration were
established. As expected, on the same value of coefficient of friction,
the maximum lateral acceleration would be increased as the GVW
increases.
Abstract: This paper presents an application of Artificial Neural
Network (ANN) algorithm for improving power system voltage
stability. The training data is obtained by solving several normal and
abnormal conditions using the Linear Programming technique. The
selected objective function gives minimum deviation of the reactive
power control variables, which leads to the maximization of
minimum Eigen value of load flow Jacobian. The considered reactive
power control variables are switchable VAR compensators, OLTC
transformers and excitation of generators. The method has been
implemented on a modified IEEE 30-bus test system. The results
obtain from the test clearly show that the trained neural network is
capable of improving the voltage stability in power system with a
high level of precision and speed.
Abstract: The paper is focused on monitoring of dependencies
of different composition concretes on elastic modulus values.
To obtain a summary of elastic modulus development in dependence
of concrete composition design variability was the objective
of the experiment. Essential part of this work was initiated
as a reaction to building practice when questions of elastic moduli
arose at the same time and which mostly did not obtain the required
and expected values from concrete constructions.
Abstract: Rice bran is normally used as a raw material for rice
bran oil production or sold as feed with a low price. Conventionally,
the protein in defatted rice bran was extracted using alkaline
extraction and acid precipitation, which involves in chemical usage
and lowering some nutritious component. This study was conducted
in order to extract of rice bran protein concentrate (RBPC) from
defatted rice bran using enzymes and employing polysaccharides in a
precipitating step. The properties of RBPC obtained will be compared
to those of a control sample extracted using a conventional method.
The results showed that extraction of protein from rice bran using
enzymes exhibited the higher protein recovery compared to that
extraction with alkaline. The extraction conditions using alcalase 2%
(v/w) at 50 C, pH 9.5 gave the highest protein (2.44%) and yield
(32.09%) in extracted solution compared to other enzymes. Rice bran
protein concentrate powder prepared by a precipitation step using
alginate (protein in solution: alginate 1:0.016) exhibited the highest
protein (27.55%) and yield (6.84%). Precipitation using alginate was
better than that of acid. RBPC extracted with alkaline (ALK) or
enzyme alcalase (ALC), then precipitated with alginate (AL)
(samples RBP-ALK-AL and RBP-ALC-AL) yielded the precipitation
rate of 75% and 91.30%, respectively. Therefore, protein
precipitation using alginate was then selected. Amino acid profile of
control sample, and sample precipitated with alginate, as compared to
casein and soy protein isolated, showed that control sample showed
the highest content among all sample. Functional property study of
RBP showed that the highest nitrogen solubility occurred in pH 8-10.
There was no statically significant between emulsion capacity and
emulsion stability of control and sample precipitated by alginate.
However, control sample showed a higher of foaming capacity and
foaming stability compared to those of sample precipitated with
alginate. The finding was successful in terms of minimizing
chemicals used in extraction and precipitation steps in preparation of
rice bran protein concentrate. This research involves in a production
of value-added product in which the double amount of protein (28%)
compared to original amount (14%) contained in rice bran could be
beneficial in terms of adding to food products e.g. healthy drink with
high protein and fiber. In addition, the basic knowledge of functional
property of rice bran protein concentrate was obtained, which can be
used to appropriately select the application of this value-added
product from rice bran.
Abstract: Perception, evaluation and representation of the
environment have been the subject of many disciplines including
psychology, geography and architecture. In environmental and social
psychology literature there are several evidences which suggest that
cognitive representations about a place consisted of not only
geographic items but also social and cultural. Mental representations
of residence area or a country are influenced and determined by
social-demographics, the physical and social context. Thus, all
mental representations of a given place are also social
representations. Cognitive maps are the main and common
instruments that are used to identify spatial images and the difference
between physical and subjective environments. The aim of the
current study is investigating the mental and social representations of
Turkey in university students’ minds. Data was collected from 249
university students from different departments (i.e. psychology,
geography, history, tourism departments) of Ege University.
Participants were requested to reflect Turkey in their mind onto the
paper drawing sketch maps. According to the results, cognitive maps
showed geographic aspects of Turkey as well as the context of
symbolic, cultural and political reality of Turkey. That is to say, these
maps had many symbolic and verbal items related to critics on social
and cultural problems, ongoing ethnic and political conflicts, and
actual political agenda of Turkey. Additionally, one of main
differentiations in these representations appeared in terms of the East
and West side of the Turkey, and the representations of the East and
West was varied correspondingly participants’ cultural background,
their ethnic values, and where they have born. The results of the
study were discussed in environmental and social psychological
perspective considering cultural and social values of Turkey and
current political circumstances of the country.
Abstract: This paper presents a new automatic vehicle detection
method from very high resolution aerial images to measure traffic
density. The proposed method starts by extracting road regions from
image using road vector data. Then, the road image is divided into
equal sections considering resolution of the images. Gradient vectors
of the road image are computed from edge map of the corresponding
image. Gradient vectors on the each boundary of the sections are
divided where the gradient vectors significantly change their
directions. Finally, number of vehicles in each section is carried out
by calculating the standard deviation of the gradient vectors in each
group and accepting the group as vehicle that has standard deviation
above predefined threshold value. The proposed method was tested in
four very high resolution aerial images acquired from Istanbul,
Turkey which illustrate roads and vehicles with diverse
characteristics. The results show the reliability of the proposed
method in detecting vehicles by producing 86% overall F1 accuracy
value.
Abstract: Diagnostic enzymes like aspartate aminotransferase
(AST), alanine aminotransferase (ALT) and alkaline phosphatase
(ALP) were determined as indices of heavy metal pollution in Tilapia
guinensis. Three different sets of fishes treated with lead (Pb), iron
(Fe) and copper (Cu) were used for the study while a fourth group
with no heavy metal served as a control. Fishes in each of the groups
were exposed to 2.65mg/l of Pb, 0.85mg/l of Fe and 0.35 mg/l of Cu
in aerated aquaria for 96 hours. Tissue fractionation of the liver
tissues was carried out and the three diagnostic enzymes (AST, ALT,
and ALP) were estimated. Serum levels of the same diagnostic
enzymes were also measured. The mean values of the serum enzyme
activity for ALP in each experimental group were 19.5±1.62,
29.67±2.17 and 1.15±0.27 IU/L for Pb, Fe and Cu groups compared
with 9.99±1.34 IU/L enzyme activity in the control. This result
showed that Pb and Fe caused increased release of the enzyme into
the blood circulation indicating increased tissue damage while Cu
caused a reduction in the serum level as compared with the level in
the control group. The mean values of enzyme activity obtained in
the liver were 102.14±6.12, 140.17±2.06 and 168.23±3.52 IU/L for
Pb, Fe and Cu groups, respectively compared to 91.20±9.42 IU/L
enzyme activity for the control group. The serum and liver AST and
ALT activities obtained in Pb, Fe, Cu and control groups are
reported. It was generally noted that the presence of the heavy metal
caused liver tissues damage and consequent increased level of the
diagnostic enzymes in the serum.
Abstract: Construction and reconstruction of settlements and
individual municipalities, environmental management and the
creation, deployment of the forces of production and building
transport and technical equipment requires a large expenditure of
material and human resources. That is why the economic aspects of
the majority decision in these planes built in the foreground and are
often decisive. Thereby but more serious is that the economic aspects
of the settlement, the creation and function remain in their whole,
unprocessed, and cannot speak of a set of individual techniques and
methods traditional indicators and experiments with new approaches.
This is true both at the level of the national economy, and in their
own urban designs. Still a few remain identified specific economic
shaping patterns of settlement and the less it is possible to speak of
their control. Also practical assessing economics of specific solutions
are often used non-apt indicators in addition to economics usually
identifies with the lowest acquisition cost or high-intensity land use
with little regard for functional efficiency and little studied much
higher operating and maintenance costs".
Abstract: When printing a plate (or dish) by an FDM 3D printer,
the process normally requires support material, which causes several
problems. This paper proposes a method for forming thin plates
without using wasteful support material. This method requires several
extraordinary parameter values when slicing plates. The experiments
show that the plates can, for the most part, be successfully formed
using a conventional slicer and a 3D printer; however, seams between
layers spoil them and the quality of printed objects strongly depends
on the slicer.
Abstract: In this paper, we investigated the athermal pressure
behavior of the structural and elastic properties of scheelite BaWO4
phase up to 7 GPa using the ab initio pseudo-potential method. The
calculated lattice parameters pressure relation have been compared
with the experimental values and found to be in good agreement with
these results. Moreover, we present for the first time the investigation
of the elastic properties of this compound using the density functional
perturbation theory (DFPT). It is shown that this phase is
mechanically stable up to 7 GPa after analyzing the calculated elastic
constants. Other relevant quantities such as bulk modulus, pressure
derivative of bulk modulus, shear modulus; Young’s modulus,
Poisson’s ratio, anisotropy factors, Debye temperature and sound
velocity have been calculated. The obtained results, which are
reported for the first time to the best of the author’s knowledge, can
facilitate assessment of possible applications of the title material.
Abstract: This paper proposed the comparison made between
Multi-Carrier Pulse Width Modulation, Sinusoidal Pulse Width
Modulation and Selective Harmonic Elimination Pulse Width
Modulation technique for minimization of Total Harmonic Distortion
in Cascaded H-Bridge Multi-Level Inverter. In Multicarrier Pulse
Width Modulation method by using Alternate Position of Disposition
scheme for switching pulse generation to Multi-Level Inverter.
Another carrier based approach; Sinusoidal Pulse Width Modulation
method is also implemented to define the switching pulse generation
system in the multi-level inverter. In Selective Harmonic Elimination
method using Genetic Algorithm and Particle Swarm Optimization
algorithm for define the required switching angles to eliminate low
order harmonics from the inverter output voltage waveform and
reduce the total harmonic distortion value. So, the results validate that
the Selective Harmonic Elimination Pulse Width Modulation method
does capably eliminate a great number of precise harmonics and
minimize the Total Harmonic Distortion value in output voltage
waveform in compared with Multi-Carrier Pulse Width Modulation
method, Sinusoidal Pulse Width Modulation method. In this paper,
comparison of simulation results shows that the Selective Harmonic
Elimination method can attain optimal harmonic minimization
solution better than Multi-Carrier Pulse Width Modulation method,
Sinusoidal Pulse Width Modulation method.
Abstract: This paper represents the results of experimental work to investigate the suitability of a waste material (WM) for soft soil stabilisation. In addition, the effect of particle size distribution (PSD) of the waste material on its performance as a soil stabiliser was investigated. The WM used in this study is produced from the incineration processes in domestic energy power plant and it is available in two different grades of fineness (coarse waste material (CWM) and fine waste material (FWM)). An intermediate plasticity silty clayey soil with medium organic matter content has been used in this study. The suitability of the CWM and FWM to improve the physical and engineering properties of the selected soil was evaluated dependant on the results obtained from the consistency limits, compaction characteristics (optimum moisture content (OMC) and maximum dry density (MDD)); along with the unconfined compressive strength test (UCS). Different percentages of CWM were added to the soft soil (3, 6, 9, 12 and 15%) to produce various admixtures. Then the UCS test was carried out on specimens under different curing periods (zero, 7, 14, and 28 days) to find the optimum percentage of CWM. The optimum and other two percentages (either side of the optimum content) were used for FWM to evaluate the effect of the fineness of the WM on UCS of the stabilised soil. Results indicated that both types of the WM used in this study improved the physical properties of the soft soil where the index of plasticity (IP) was decreased significantly. IP was decreased from 21 to 13.64 and 13.10 with 12% of CWM and 15% of FWM respectively. The results of the unconfined compressive strength test indicated that 12% of CWM was the optimum and this percentage developed the UCS value from 202kPa to 500kPa for 28 days cured samples, which is equal, approximately 2.5 times the UCS value for untreated soil. Moreover, this percentage provided 1.4 times the value of UCS for stabilized soil-CWA by using FWM which recorded just under 700kPa after 28 days curing.
Abstract: We report herein the development and preliminary mechanical characterization of fully-dense multi-wall carbon nanotube (MWCNT)-reinforced ceramics and glasses based on a completely new methodology termed High Shear Compaction (HSC). The tubes are introduced and bound to the matrix grains by aid of polymeric binders to form flexible green bodies which are sintered and densified by spark plasma sintering to unprecedentedly high densities of 100% of the pure-matrix value. The strategy was validated across a PyrexTM glass / MWCNT composite while no identifiable factors limit application to other types of matrices. Nondestructive evaluation, based on ultrasonics, of the dynamic mechanical properties of the materials including elastic, shear and bulk modulus as well as Poisson’s ratio showed optimum property improvement at 0.5 %wt tube loading while evidence of nanoscalespecific energy dissipative characteristics acting complementary to nanotube bridging and pull-out indicate a high potential in a wide range of reinforcing and multifunctional applications.
Abstract: The crude methanol extracts of five indigenous vegetables namely, Amarathus tricolor, Basella rubra L., Chochurus olitorius L., Ipomea batatas, and Momordica chuchinensis L., were examined for their phytochemical profile and antioxidant activity using 1,1-diphenyl-2-picrylhydrazyl (DPPH) free radical. The values for DPPH radical scavenging activity ranged from 7.6-89.53% with B. rubra and I. batatas having the lowest and highest values, respectively. The total flavonoid content of all five indigenous vegetables ranged from 74.65-277.3 mg quercetin equivalent per gram of dried vegetable material while the total phenolic content ranged from 1.93-6.15 mg gallic acid equivalent per gram dried material. Phytochemical screening revealed the presence of steroids, flavonoids, saponins, tannins, carbohydrates and reducing sugars, which may also be associated with the antioxidant activity shown by these indigenous vegetables.
Abstract: In the present study, response surface methodology has been used to optimize turn-assisted deep cold rolling process of AISI 4140 steel. A regression model is developed to predict surface hardness and surface roughness using response surface methodology and central composite design. In the development of predictive model, deep cold rolling force, ball diameter, initial roughness of the workpiece, and number of tool passes are considered as model variables. The rolling force and the ball diameter are the significant factors on the surface hardness and ball diameter and numbers of tool passes are found to be significant for surface roughness. The predicted surface hardness and surface roughness values and the subsequent verification experiments under the optimal operating conditions confirmed the validity of the predicted model. The absolute average error between the experimental and predicted values at the optimal combination of parameter settings for surface hardness and surface roughness is calculated as 0.16% and 1.58% respectively. Using the optimal processing parameters, the surface hardness is improved from 225 to 306 HV, which resulted in an increase in the near surface hardness by about 36% and the surface roughness is improved from 4.84µm to 0.252 µm, which resulted in decrease in the surface roughness by about 95%. The depth of compression is found to be more than 300µm from the microstructure analysis and this is in correlation with the results obtained from the microhardness measurements. Taylor hobson talysurf tester, micro vickers hardness tester, optical microscopy and X-ray diffractometer are used to characterize the modified surface layer.