Abstract: Cavitation, usually known as a destructive
phenomenon, involves turbulent unsteady two-phase flow. Having
such features, cavitating flows have been turned to a challenging
topic in numerical studies and many researches are being done for
better understanding of bubbly flows and proposing solutions to
reduce its consequent destructive effects. Aeration may be regarded
as an effective protection against cavitation erosion in many
hydraulic structures, like gated tunnels. The paper concerns
numerical simulation of flow in discharge gated tunnel of a dam
using ing RNG k -ε model coupled with the volume of fluid (VOF)
method and the zone which is susceptible of cavitation inception in
the tunnel is predicted. In the second step, a vent is considered in the
mentioned zone for aeration and the numerical simulation is done
again to study the effects of aeration. The results show that aeration
is an impressively useful method to exclude cavitation in mentioned
tunnels.
Abstract: This paper investigates the effect of replacing
crankshaft with cam on the indicated torque during compression and
power strokes in internal combustion engines. A Cycloidal cam
profile was used in Revetec engine to calculate and compare the
torque to a conventional engine, using a computational method.
Firstly, the cylinder pressure was calculated using Ferguson equation,
and then the torque calculated depending on cylinder pressure values
in every crank angle. the results showed that by using Cycloidal cam
profile in Revetec engine the torque can increased by 14% compared
with conventional engines, which means an increase in engine
efficiency.
Abstract: This paper proposes an alternative control mechanism
for an interactive Pan/Tilt/Zoom (PTZ) camera control system.
Instead of using a mouse or a joystick, the proposed mechanism
utilizes a Nintendo Wii remote and infrared (IR) sensor bar. The Wii
remote has buttons that allows the user to control the movement of a
PTZ camera through Bluetooth connectivity. In addition, the Wii
remote has a built-in motion sensor that allows the user to give
control signals to the PTZ camera through pitch and roll movement.
A stationary IR sensor bar, placed at some distance away opposite the
Wii remote, enables the detection of yaw movement. In addition, the
Wii remote-s built-in IR camera has the ability to detect its spatial
position, and thus generates a control signal when the user moves the
Wii remote. Some experiments are carried out and their performances
are compared with an industry-standard PTZ joystick.
Abstract: Antibacterial activity of Plumeria alba (Frangipani)
petals methanolic extracts were evaluated against Escherichia coli,
Proteus vulgaris,Staphylococcus aureus, Klebsiella pneumoniae,
Pseudomonas aeruginosa, Staphylococcus saprophyticus,
Enterococcus faecalis and Serratia marcescens by using disk
diffusion method. Concentration extracts (80 %) showed the highest
inhibition zone towards Escherichia coli (14.3 mm). Frangipani
extract also showed high antibacterial activity against
Staphylococcus saprophyticus, Proteus vulgaris and Serratia
marcescens, but not more than the zones of the positive control used.
Comparison between two broad specrum antibiotics to frangipani
extracts showed that the 80 % concentration extracts produce the
same zone of inhibition as Streptomycin. Frangipani extracts showed
no bacterial activity towards Klebsiella pneumoniae, Pseudomonas
aeruginosa and Enterococcus faecalis. There are differences in the
sensitivity of different bacteria to frangipani extracts, suggesting that
frangipani-s potency varies between these bacteria. The present
results indicate that frangipani showed significant antibacterial
activity especially to Escherichia coli.
Abstract: Clustering algorithms are attractive for the task of class identification in spatial databases. However, the application to large spatial databases rises the following requirements for clustering algorithms: minimal requirements of domain knowledge to determine the input parameters, discovery of clusters with arbitrary shape and good efficiency on large databases. The well-known clustering algorithms offer no solution to the combination of these requirements. In this paper, a density based clustering algorithm (DCBRD) is presented, relying on a knowledge acquired from the data by dividing the data space into overlapped regions. The proposed algorithm discovers arbitrary shaped clusters, requires no input parameters and uses the same definitions of DBSCAN algorithm. We performed an experimental evaluation of the effectiveness and efficiency of it, and compared this results with that of DBSCAN. The results of our experiments demonstrate that the proposed algorithm is significantly efficient in discovering clusters of arbitrary shape and size.
Abstract: Stormwater wetlands have been mainly designed in an
empirical approach for water quality improvement, with little
quantitative understanding of the internal microbial processes. This
study investigated into heterotrophic bacterial production rate,
heterotrophic bacterial mineralization percentage, and algal biomass
in hypertrophic and eutrophic surface flow stormwater wetlands.
Compared to a nearby wood leachate treatment wetland, the
stormwater wetlands had much higher chlorophyll-a concentrations.
The eutrophic stormwater wetland had improved water quality,
whereas the hypertrophic stormwater wetland had degraded water
quality. Heterotrophic bacterial activities in water were limited in the
stormwater wetlands due to competition of algal growth for nutrients.
The relative contribution of biofilms to the overall heterotrophic
activities was higher in the stormwater wetlands than that in the wood
leachate treatment wetland.
Abstract: Theobjective of this study was to evaluate the optimal
treatment condition of Fenton oxidation process to removal
contaminant in soil slurry contaminated by petroleum hydrocarbons.
This research studied somefactors that affect the removal efficiency
of petroleum hydrocarbons in soil slurry including molar ratio of
hydrogen peroxide (H2O2) to ferrous ion(Fe2+), pH condition and
reaction time.The resultsdemonstrated that the optimum condition
was that the molar ratio of H2O2:Fe3+ was 200:1,the pHwas 4.0and
the rate of reaction was increasing rapidly from starting point to 7th
hour and destruction kinetic rate (k) was 0.24 h-1. Approximately
96% of petroleum hydrocarbon was observed(initialtotal petroleum
hydrocarbon (TPH) concentration = 70±7gkg-1)
Abstract: At present, the tendency to implement the conditionbased
maintenance (CBM), which allows the optimization of the
expenses for equipment monitoring, is more and more evident; also,
the transformer substations with remote monitoring are increasingly
used. This paper reviews all the advantages of the on-line monitoring
and presents an equipment for on-line monitoring of bushings, which
is the own contribution of specialists who are the authors of this
paper. The paper presents a study of the temperature field, using the
finite element method. For carrying out this study, the 3D modelling
of the above mentioned bushing was performed. The analysis study is
done taking into account the extreme thermal stresses, focusing at the
level of the first cooling wing section of the ceramic insulator. This
fact enables to justify the tanδ variation in time, depending on the
transformer loading and the environmental conditions. With a view
to reducing the variation of dielectric losses in bushing insulation, the
use of ferrofuids instead of mineral oils is proposed.
Abstract: Ovshinsky initiated scientific research in the field of
amorphous and disordered materials that continues to this day. The
Ovshinsky Effect where the resistance of thin GST films is
significantly reduced upon the application of low voltage is of
fundamental importance in phase-change - random access memory
(PC-RAM) devices.GST stands for GdSbTe chalcogenide type
glasses.However, the Ovshinsky Effect is not without controversy.
Ovshinsky thought the resistance of GST films is reduced by the
redistribution of charge carriers; whereas, others at that time including
many PC-RAM researchers today argue that the GST resistance
changes because the GST amorphous state is transformed to the
crystalline state by melting, the heat supplied by external heaters. In
this controversy, quantum mechanics (QM) asserts the heat capacity of
GST films vanishes, and therefore melting cannot occur as the heat
supplied cannot be conserved by an increase in GST film
temperature.By precluding melting, QM re-opens the controversy
between the melting and charge carrier mechanisms. Supporting
analysis is presented to show that instead of increasing GST film
temperature, conservation proceeds by the QED induced creation of
photons within the GST film, the QED photons confined by TIR. QED
stands for quantum electrodynamics and TIR for total internal
reflection. The TIR confinement of QED photons is enhanced by the
fact the absorbedheat energy absorbed in the GST film is concentrated
in the TIR mode because of their high surface to volume ratio. The
QED photons having Planck energy beyond the ultraviolet produce
excitons by the photoelectric effect, the electrons and holes of which
reduce the GST film resistance.
Abstract: A transient heat transfer mathematical model for the
prediction of temperature distribution in the car body during primer
baking has been developed by considering the thermal radiation and
convection in the furnace chamber and transient heat conduction
governing equations in the car framework. The car cockpit is
considered like a structure with six flat plates, four vertical plates
representing the car doors and the rear and front panels. The other
two flat plates are the car roof and floor. The transient heat
conduction in each flat plate is modeled by the lumped capacitance
method. Comparison with the experimental data shows that the heat
transfer model works well for the prediction of thermal behavior of
the car body in the curing furnace, with deviations below 5%.
Abstract: Statistical selection procedures are used to select the
best simulated system from a finite set of alternatives. In this paper,
we present a procedure that can be used to select the best system
when the number of alternatives is large. The proposed procedure
consists a combination between Ranking and Selection, and Ordinal
Optimization procedures. In order to improve the performance of Ordinal
Optimization, Optimal Computing Budget Allocation technique
is used to determine the best simulation lengths for all simulation
systems and to reduce the total computation time. We also argue
the effect of increment in simulation samples for the combined
procedure. The results of numerical illustration show clearly the effect
of increment in simulation samples on the proposed combination of
selection procedure.
Abstract: A method is presented for the construction of arbitrary
even-input sorting networks exhibiting better properties than the
networks created using a conventional technique of the same type.
The method was discovered by means of a genetic algorithm combined
with an application-specific development. Similarly to human
inventions in the area of theoretical computer science, the evolved
invention was analyzed: its generality was proven and area and time
complexities were determined.
Abstract: A study of electromagnetic flow meter is presented in the paper. Comparison has been made between the analytical and the numerical results by the use of FEM numerical analysis (Quick Field 5.6) for determining polarization voltage through the circle cross section of the polarization transducer. Exciting and geometrical parameters increasing its effectiveness has been examined. The aim is to obtain maximal output signal. The investigations include different variants of the magnetic flux density distribution around the tube: homogeneous field of magnitude Bm, linear distribution with maximal value Bm and trapezium distribution conserving the same exciting magnetic energy as the homogeneous field.
Abstract: Fick's second law equations for unsteady state
diffusion of salt into the potato tissues were solved numerically. The
set of equations resulted from implicit modeling were solved using
Thomas method to find the salt concentration profiles in solid phase.
The needed effective diffusivity and equilibrium distribution
coefficient were determined experimentally. Cylindrical samples of
potato were infused with aqueous NaCl solutions of 1-3%
concentrations, and variations in salt concentrations of brine were
determined over time. Solute concentrations profiles of samples were
determined by measuring salt uptake of potato slices. For the studied
conditions, equilibrium distribution coefficients were found to be
dependent on salt concentrations, whereas the effective diffusivity
was slightly affected by brine concentration.
Abstract: Unsteady magnetohydrodynamics (MHD) boundary
layer flow and heat transfer over a continuously stretching surface in
the presence of radiation is examined. By similarity transformation,
the governing partial differential equations are transformed to a set of
ordinary differential equations. Numerical solutions are obtained by
employing the Runge-Kutta-Fehlberg method scheme with shooting
technique in Maple software environment. The effects of
unsteadiness parameter, radiation parameter, magnetic parameter and
Prandtl number on the heat transfer characteristics are obtained and
discussed. It is found that the heat transfer rate at the surface
increases as the Prandtl number and unsteadiness parameter increase
but decreases with magnetic and radiation parameter.
Abstract: There is a growing body of evidence to support the
proposition of product take back for remanufacturing particularly
within the context of Extended Producer Responsibility (EPR).
Remanufacturing however presents challenges unlike that of
traditional manufacturing environments due to its high levels of
uncertainty which may further distract organizations from
considering its potential benefits. This paper presents a novel
modeling approach for evaluating the uncertainty of part failures
within the remanufacturing process and its impact on economic and
environmental performance measures. This paper presents both the
theoretical modeling approach and an example of its use in
application.
Abstract: We present a genetic algorithm application to the problem of object registration (i.e., object detection, localization and recognition) in a class of medical images containing various types of blood cells. The genetic algorithm approach taken here is seen to be most appropriate for this type of image, due to the characteristics of the objects. Successful cell registration results on real life microscope images of blood cells show the potential of the proposed approach.
Abstract: Adhesion strength of exterior or interior coating of
steel pipes is too important. Increasing of coating adhesion on
surfaces can increase the life time of coating, safety factor of
transmitting line pipe and decreasing the rate of corrosion and costs.
Preparation of steel pipe surfaces before doing the coating process is
done by shot and grit blasting. This is a mechanical way to do it.
Some effective parameters on that process, are particle size of
abrasives, distance to surface, rate of abrasive flow, abrasive physical
properties, shapes, selection of abrasive, kind of machine and its
power, standard of surface cleanness degree, roughness, time of
blasting and weather humidity. This search intended to find some
better conditions which improve the surface preparation, adhesion
strength and corrosion resistance of coating. So, this paper has
studied the effect of varying abrasive flow rate, changing the
abrasive particle size, time of surface blasting on steel surface
roughness and over blasting on it by using the centrifugal blasting
machine. After preparation of numbers of steel samples (according to
API 5L X52) and applying epoxy powder coating on them, to
compare strength adhesion of coating by Pull-Off test. The results
have shown that, increasing the abrasive particles size and flow rate,
can increase the steel surface roughness and coating adhesion
strength but increasing the blasting time can do surface over blasting
and increasing surface temperature and hardness too, change,
decreasing steel surface roughness and coating adhesion strength.
Abstract: This paper presents the utilizing of ferroelectric
material on antenna application. There are two different ferroelectric
had been used on the proposed antennas which include of Barium
Strontium Titanate (BST) and Bismuth Titanate (BiT), suitable for
Access Points operating in the WLAN IEEE 802.11 b/g and WiMAX
IEEE 802.16 within the range of 2.3 GHz to 2.5 GHz application.
BST, which had been tested to own a dielectric constant of εr = 15
while BiT has a dielectric constant that higher than BST which is εr =
21 and both materials are in rectangular shaped. The influence of
various parameters on antenna characteristics were investigated
extensively using commercial electromagnetic simulations software
by Communication Simulation Technology (CST). From theoretical
analysis and simulation results, it was demonstrated that ferroelectric
material used have not only improved the directive emission but also
enhanced the radiation efficiency.
Abstract: Nurses in an Armed Force Hospital (AFH) expose to stronger stress than those in a civil hospital, especially in an emergency department (ED). Ironically, stresses of these nurses received few if any attention in academic research in the past. This study collects 227 samples from the emergency departments of four armed force hospitals in central and southern Taiwan. The research indicates that the top five stressors are a massive casualty event, delayed physician support, overloads of routine work, overloads of assignments, and annoying paper work. Excessive work loading was found to be the primary source of stress. Nurses who were perceived to have greater stress levels were more inclined to deploy emotion-oriented approaches and more likely to seek job rotations. Professional stressors and problem-oriented approaches were positively correlated. Unlike other local studies, this study concludes that the excessive work-loading is more stressful in an AFH.