Abstract: This analysis investigates the distortion of flow
measurement and the increase of cavitation along orifice
flowmeter. The analysis using the numerical method (CFD)
validated the distortion of flow measurement through the inlet
velocity profile considering the convergence and grid
dependency. Realizable k-e model was selected and y+ was
about 50 in this numerical analysis. This analysis also estimated
the vulnerability of cavitation effect due to inlet velocity profile.
The investigation concludes that inclined inlet velocity profile
could vary the pressure which was measured at pressure tab
near pipe wall and it led to distort the pressure values ranged
from -3.8% to 5.3% near the orifice plate and to make the
increase of cavitation. The investigation recommends that the
fully developed inlet velocity flow is beneficial to accurate flow
measurement in orifice flowmeter.
Abstract: In the present study, Convective heat transfer
coefficient and pressure drop of Al2O3/water nanofluid in laminar
flow regime under constant heat flux conditions inside a circular tube
were experimentally investigated. Al2O3/water nanofluid with 0.5%
and 1% volume concentrations with 15 nm diameter nanoparticles
were used as working fluid. The effect of different volume
concentrations on convective heat transfer coefficient and friction
factor was studied. The results emphasize that increasing of particle
volume concentration leads to enhance convective heat transfer
coefficient. Measurements show the average heat transfer coefficient
enhanced about 11-20% with 0.5% volume concentration and
increased about 16-27% with 1% volume concentration compared to
distilled water. In addition, the convective heat transfer coefficient of
nanofluid enhances with increase in heat flux. From the results, the
average ratio of (fnf/fbf) was about 1.10 for 0.5% volume
concentration. Therefore, there is no significant increase in friction
factor for nanofluids.
Abstract: Degradation of polymeric insulation systems of
electrical equipments increases the space charge density and the
concentration of electrical dipoles. By consequence, the maximum
values and the slopes of absorption/resorption (A/R) currents can
change with insulation systems ageing. In this paper, an analysis of
the nature of the A/R currents and the importance of their
components, especially the polarization current and the current given
by the space charge, is presented. The experimental study concerns
the A/R currents measurements of plane samples (made from
CALMICAGLAS tapes), virgin and thermally accelerated aged. The
obtained results show that the ageing process produces an increase of
the values and a decrease of shapes of the A/R currents. Finally, the
possibility of estimating insulations ageing state and lifetime from
A/R currents measurements is discussed.
Abstract: This study investigates the capacity of granular
activated carbon (GAC) for the storage of methane through the
equilibrium adsorption. An experimental apparatus consist of a dual
adsorption vessel was set up for the measurement of equilibrium
adsorption of methane on GAC using volumetric technique (pressure
decay). Experimental isotherms of methane adsorption were
determined by the measurement of equilibrium uptake of methane in
different pressures (0-50 bar) and temperatures (285.15-328.15°K).
The experimental data was fitted to Freundlich and Langmuir
equations to determine the model isotherm. The results show that the
experimental data is equally well fitted by the both model isotherms.
Using the experimental data obtained in different temperatures the
isosteric heat of methane adsorption was also calculated by the
Clausius-Clapeyron equation from the Sips isotherm model. Results
of isosteric heat of adsorption show that decreasing temperature or
increasing methane uptake by GAC decrease the isosteric heat of
methane adsorption.
Abstract: In this paper, a vision based system has been used for
controlling an industrial 3P Cartesian robot. The vision system will
recognize the target and control the robot by obtaining images from
environment and processing them. At the first stage, images from
environment are changed to a grayscale mode then it can diverse and
identify objects and noises by using a threshold objects which are
stored in different frames and then the main object will be
recognized. This will control the robot to achieve the target. A vision
system can be an appropriate tool for measuring errors of a robot in a
situation where the experimental test is conducted for a 3P robot.
Finally, the international standard ANSI/RIA R15.05-2 is used for
evaluating the path-related characteristics of the robot. To evaluate
the performance of the proposed method experimental test is carried
out.
Abstract: We propose a new fiber lens structure for large distance
measurement in which a polymer layer is added to a conventional
fiber lens. The proposed fiber lens can adjust the working distance by
properly choosing the refractive index and thickness of the polymer
layer. In our numerical analysis for the fiber lens radius of 120 μm,
the working distance of the proposed fiber lens is about 10 mm
which is about 30 times larger than conventional fiber lens.
Abstract: Study of soil properties like field capacity (F.C.) and permanent wilting point (P.W.P.) play important roles in study of soil moisture retention curve. Although these parameters can be measured directly, their measurement is difficult and expensive. Pedotransfer functions (PTFs) provide an alternative by estimating soil parameters from more readily available soil data. In this investigation, 70 soil samples were collected from different horizons of 15 soil profiles located in the Ziaran region, Qazvin province, Iran. The data set was divided into two subsets for calibration (80%) and testing (20%) of the models and their normality were tested by Kolmogorov-Smirnov method. Both multivariate regression and artificial neural network (ANN) techniques were employed to develop the appropriate PTFs for predicting soil parameters using easily measurable characteristics of clay, silt, O.C, S.P, B.D and CaCO3. The performance of the multivariate regression and ANN models was evaluated using an independent test data set. In order to evaluate the models, root mean square error (RMSE) and R2 were used. The comparison of RSME for two mentioned models showed that the ANN model gives better estimates of F.C and P.W.P than the multivariate regression model. The value of RMSE and R2 derived by ANN model for F.C and P.W.P were (2.35, 0.77) and (2.83, 0.72), respectively. The corresponding values for multivariate regression model were (4.46, 0.68) and (5.21, 0.64), respectively. Results showed that ANN with five neurons in hidden layer had better performance in predicting soil properties than multivariate regression.
Abstract: The effect of different tempering temperatures and heat treatment times on the corrosion resistance of austenitic stainless steels in oxalic acid was studied in this work using conventional weight loss and electrochemical measurements. Typical 304 and 316 stainless steel samples were tempered at 150oC, 250oC and 350oC after being austenized at 1050oC for 10 minutes. These samples were then immersed in 1.0M oxalic acid and their weight losses were measured at every five days for 30 days. The results show that corrosion of both types of ASS samples increased with an increase in tempering temperature and time and this was due to the precipitation of chromium carbides at the grain boundaries of these metals. Electrochemical results also confirm that the 304 ASS is more susceptible to corrosion than 316 ASS in this medium. This is attributed to the molybdenum in the composition of the latter. The metallographic images of these samples showed non–uniform distribution of precipitated chromium carbides at the grain boundaries of these metals and unevenly distributed carbides and retained austenite phases which cause galvanic effects in the medium.
Abstract: This paper presents the identification of the impact
force acting on a simply supported beam. The force identification is
an inverse problem in which the measured response of the structure is
used to determine the applied force. The identification problem is
formulated as an optimization problem and the genetic algorithm is
utilized to solve the optimization problem. The objective function is
calculated on the difference between analytical and measured
responses and the decision variables are the location and magnitude
of the applied force. The results from simulation show the
effectiveness of the approach and its robustness vs. the measurement
noise and sensor location.
Abstract: The objective of this paper is to present a research
study of the convectors that are used for heating or cooling of the
living room or industrial halls. The key points are experimental
measurement and comprehensive numerical simulation of the flow
coming throughout the part of the convector such as heat exchanger,
input from the fan etc.. From the obtained results, the components of
the convector are optimized in sense to increase thermal power
efficiency due to improvement of heat convection or reduction of air
drag friction. Both optimized aspects are leading to the more
effective service conditions and to energy saving. The significant part
of the convector research is a design of the unique measurement
laboratory and adopting measure techniques. The new laboratory
provides possibility to measure thermal power efficiency and other
relevant parameters under specific service conditions of the
convectors.
Abstract: WLAN Positioning has been presented by many
approaches in literatures using the characteristics of Received Signal
Strength (RSS), Time of Arrival (TOA) or Time Difference of
Arrival (TDOA), Angle of Arrival (AOA) and cell ID. Among these,
RSS approach is the simplest method to implement because there is
no need of modification on both access points and client devices
whereas its accuracy is terrible due to physical environments. For
TOA or TDOA approach, the accuracy is quite acceptable but most
researches have to modify either software or hardware on existing
WLAN infrastructure. The scales of modifications are made on only
access card up to the changes in protocol of WLAN. Hence, it is an
unattractive approach to use TOA or TDOA for positioning system.
In this paper, the new concept of merging both RSS and TOA
positioning techniques is proposed. In addition, the method to
achieve TOA characteristic for positioning WLAN user without any
extra modification necessarily appended in the existing system is
presented. The measurement results confirm that the proposed
technique using both RSS and TOA characteristics provides better
accuracy than using only either RSS or TOA approach.
Abstract: This paper presents a method to detect multiple cracks
based on frequency information. When a structure is subjected to
dynamic or static loads, cracks may develop and the modal
frequencies of the cracked structure may change. To detect cracks in a
structure, we construct a high precision wavelet finite element (EF)
model of a certain structure using the B-spline wavelet on the interval
(BSWI). Cracks can be modeled by rotational springs and added to the
FE model. The crack detection database will be obtained by solving
that model. Then the crack locations and depths can be determined
based on the frequency information from the database. The
performance of the proposed method has been numerically verified by
a rotor example.
Abstract: The major objective of this study is to understand the
potential of a newly fabricated equipment to study the thermal
properties of nonwoven textile fabrics treated with aerogel at subzero
temperatures. Thermal conductivity was calculated by using the
empirical relation Fourier’s law, The relationship between the
thermal conductivity and thermal resistance of the samples were
studied at various environmental temperatures (which was set in the
clima temperature system between +25oC to -25oC). The newly
fabricated equipment was found to be a suitable for measuring at
subzero temperatures. This field of measurements is being developed
and will be the subject of further research which will be more suitable
for measurement of the various thermal characteristics.
Abstract: Process-oriented software development is a new
software development paradigm in which software design is modeled
by a business process which is in turn translated into a process
execution language for execution. The building blocks of this
paradigm are software units that are composed together to work
according to the flow of the business process. This new paradigm
still exhibits the characteristic of the applications built with the
traditional software component technology. This paper discusses an
approach to apply a traditional technique for software component
fabrication to the design of process-oriented software units, called
process components. These process components result from
decomposing a business process of a particular application domain
into subprocesses, and these process components can be reused to
design the business processes of other application domains. The
decomposition considers five managerial goals, namely cost
effectiveness, ease of assembly, customization, reusability, and
maintainability. The paper presents how to design or decompose
process components from a business process model and measure
some technical features of the design that would affect the
managerial goals. A comparison between the measurement values
from different designs can tell which process component design is
more appropriate for the managerial goals that have been set. The
proposed approach can be applied in Web Services environment
which accommodates process-oriented software development.
Abstract: In this paper, the noise maps for the area encircled by
the Second Ring Road in Riyadh city are developed based on real
measured data. Sound level meters, GPS receivers to determine
measurement position, a database program to manage the measured
data, and a program to develop the maps are used. A baseline noise
level has been established at each short-term site so subsequent
monitoring may be conducted to describe changes in Riyadh-s noise
environment. Short-term sites are used to show typical daytime and
nighttime noise levels at specific locations by short duration grab
sampling.
Abstract: The development and extension of large cities induced
a need for shallow tunnel in soft ground of building areas. Estimation
of ground settlement caused by the tunnel excavation is important
engineering point. In this paper, prediction of surface subsidence
caused by tunneling in one section of seventh line of Tehran subway
is considered. On the basis of studied geotechnical conditions of the
region, tunnel with the length of 26.9km has been excavated applying
a mechanized method using an EPB-TBM with a diameter of 9.14m.
In this regard, settlement is estimated utilizing both analytical and
numerical finite element method. The numerical method shows that
the value of settlement in this section is 5cm. Besides, the analytical
consequences (Bobet and Loganathan-Polous) are 5.29 and 12.36cm,
respectively. According to results of this study, due tosaturation of
this section, there are good agreement between Bobet and numerical
methods. Therefore, tunneling processes in this section needs a
special consolidation measurement and support system before the
passage of tunnel boring machine.
Abstract: In this study we applied thermal lens (TL) technique
to study the effect of size on thermal diffusivity of cadmium sulphide
(CdS) nanofluid prepared by using γ-radiation method containing
particles with different sizes. In TL experimental set up a diode laser
of wavelength 514 nm and intensity stabilized He-Ne laser were used
as the excitation source and the probe beam respectively,
respectively. The experimental results showed that the thermal
diffusivity value of CdS nanofluid increases when the of particle size
increased.
Abstract: Laboratory activities have produced benefits in
student learning. With current drives of new technology resources
and evolving era of education methods, renewal status of learning
and teaching in laboratory methods are in progress, for both learners
and the educators. To enhance learning outcomes in laboratory works
particularly in engineering practices and testing, learning via handson
by instruction may not sufficient. This paper describes and
compares techniques and implementation of traditional (expository)
with open-ended laboratory (problem-based) for two consecutive
cohorts studying environmental laboratory course in civil engineering
program. The transition of traditional to problem-based findings and
effect were investigated in terms of course assessment student
feedback survey, course outcome learning measurement and student
performance grades. It was proved that students have demonstrated
better performance in their grades and 12% increase in the course
outcome (CO) in problem-based open-ended laboratory style than
traditional method; although in perception, students has responded
less favorable in their feedback.
Abstract: The necessity of updating the numerical models inputs, because of geometrical and resistive variations in rivers subject to solid transport phenomena, requires detailed control and monitoring activities. The human employment and financial resources of these activities moves the research towards the development of expeditive methodologies, able to evaluate the outflows through the measurement of more easily acquirable sizes. Recent studies highlighted the dependence of the entropic parameter on the kinematical and geometrical flow conditions. They showed a meaningful variability according to the section shape, dimension and slope. Such dependences, even if not yet well defined, could reduce the difficulties during the field activities, and also the data elaboration time. On the basis of such evidences, the relationships between the entropic parameter and the geometrical and resistive sizes, obtained through a large and detailed laboratory experience on steady free surface flows in conditions of macro and intermediate homogeneous roughness, are analyzed and discussed.
Abstract: The turbulent mixing of coolant streams of different
temperature and density can cause severe temperature fluctuations in
piping systems in nuclear reactors. In certain periodic contraction
cycles these conditions lead to thermal fatigue. The resulting aging
effect prompts investigation in how the mixing of flows over a sharp
temperature/density interface evolves. To study the fundamental
turbulent mixing phenomena in the presence of density gradients,
isokinetic (shear-free) mixing experiments are performed in a square
channel with Reynolds numbers ranging from 2-500 to 60-000.
Sucrose is used to create the density difference. A Wire Mesh Sensor
(WMS) is used to determine the concentration map of the flow in the
cross section. The mean interface width as a function of velocity,
density difference and distance from the mixing point are analyzed
based on traditional methods chosen for the purposes of
atmospheric/oceanic stratification analyses. A definition of the
mixing layer thickness more appropriate to thermal fatigue and based
on mixedness is devised. This definition shows that the thermal
fatigue risk assessed using simple mixing layer growth can be
misleading and why an approach that separates the effects of large
scale (turbulent) and small scale (molecular) mixing is necessary.