Abstract: Although water only takes a little percentage in the total mass of soil, it indeed plays an important role to the strength of structure. Moisture transfer can be carried out by many different mechanisms which may involve heat and mass transfer, thermodynamic phase change, and the interplay of various forces such as viscous, buoyancy, and capillary forces. The continuum models are not well suited for describing those phenomena in which the connectivity of the pore space or the fracture network, or that of a fluid phase, plays a major role. However, Lattice Boltzmann methods (LBMs) are especially well suited to simulate flows around complex geometries. Lattice Boltzmann methods were initially invented for solving fluid flows. Recently, fluid with multicomponent and phase change is also included in the equations. By comparing the numerical result with experimental result, the Lattice Boltzmann methods with phase change will be optimized.
Abstract: This study was conducted to investigate the efficacy
of five herbicides on narrow leaved weeds and growth and yield of
wheat. An experiment was conducted at Agronomic Research
Farm, University of Agriculture Faisalabad. The experiment was
laid out in randomized complete block designee (RCBD) with three
replications. Treatments studied were clodinafop (Topic-15 WG) at
37 g a.i. ha-1, clodinafop (Topaz-15 WG) at 45 g a.i. ha-1,
fenoxaprop-p-ethyl (Puma Super-75 EW) at 45 g a.i. ha-1,
fenoxaprop-p-ethyl (Gramicide-6.9 EW) at 85 g a.i. ha-1,
fenoxaprop-p-ethyl (Chinlima-6.9 EW) at 85 g a.i. ha-1 and weedy
check. Plots treated with fenoxaprop-p-ethyl (Puma Super-75 EW)
at 45 g a.i. ha-1 produced relatively less weed biomass, more plant
height, number of spike bearing tillers, number of grains per spike,
1000-grain weight and grain yield (4.20 t ha-1).
Abstract: This paper provides an exergy analysis of the multistage refrigeration cycle used for C2+ recovery plant. The behavior of an industrial refrigeration cycle with refrigerant propane has been investigated by the exergy method. A computational model based on the exergy analysis is presented for the investigation of the effects of the valves on the exergy losses, the second law of efficiency, and the coefficient of performance (COP) of a vapor compression refrigeration cycle. The equations of exergy destruction and exergetic efficiency for the main cycle components such as evaporators, condensers, compressors, and expansion valves are developed. The relations for the total exergy destruction in the cycle and the cycle exergetic efficiency are obtained. An ethane recovery unit with its refrigeration cycle has been simulated to prepare the exergy analysis. Using a typical actual work input value; the exergetic efficiency of the refrigeration cycle is determined to be 39.90% indicating a great potential for improvements. The simulation results reveal that the exergetic efficiencies of the heat exchanger and expansion sections get the lowest rank among the other compartments of refrigeration cycle. Refrigeration calculations have been carried out through the analysis of T–S and P–H diagrams where coefficient of performance (COP) was obtained as 1.85. The novelty of this article includes the effect and sensitivity analysis of molar flow, pressure drops and temperature on the exergy efficiency and coefficient of performance of the cycle.
Abstract: The peel of dragon fruit is a byproduct left over after consuming. Normally, the use of plants as antioxidant source must be dried before further process. Therefore, the aim of this study is interesting to dry the peel by heat pump dryer (45 ºC) and fluidized bed dryer (110 º C) compared with the sun drying method. The sample with initial moisture content of about 85-91% wet basis was dried down to about 10% wet basis where it took 620 and 25 min for heat pump dryer and fluidized bed dryer, respectively. However, the sun drying took about 900 min to dry the peel. After that, sample was evaluated antioxidant activity, -carotene and betalains contents. The results found that the antioxidant activity and betalains contents of dried peel obtained from heat pump and fluidized bed dryings were significantly higher than that sun drying (p 0.05). Moreover, the drying by heat pump provided the highest -carotene content.
Abstract: In this study the elastic-plastic stress distribution in
weld-bonded joint, fabricated from austenitic stainless steel (AISI
304) sheet of 1.00 mm thickness and Epoxy adhesive Araldite 2011,
subjected to axial loading is investigated. This is needed to improve
design procedures and welding codes, and saving efforts in the
cumbersome experiments and analysis. Therefore, a complete 3-D
finite element modelling and analysis of spot welded, bonded and
weld-bonded joints under axial loading conditions is carried out. A
comprehensive systematic experimental program is conducted to
determine many properties and quantities, of the base metals and the
adhesive, needed for FE modelling, such like the elastic – plastic
properties, modulus of elasticity, fracture limit, the nugget and heat
affected zones (HAZ) properties, etc. Consequently, the finite
element models developed, for each case, are used to evaluate
stresses distributions across the entire joint, in both the elastic and
plastic regions. The stress distribution curves are obtained,
particularly in the elastic regions and found to be consistent and in
excellent agreement with the published data. Furthermore, the
stresses distributions are obtained in the weld-bonded joint and
display the best results with almost uniform smooth distribution
compared to spot and bonded cases. The stress concentration peaks at
the edges of the weld-bonded region, are almost eliminated resulting
in achieving the strongest joint of all processes.
Abstract: In this paper a polymer electrolyte membrane (PEM)
fuel cell power system including burner, steam reformer, heat
exchanger and water heater has been considered to meet the
electrical, heating, cooling and domestic hot water loads of
residential building which in Tehran. The system uses natural gas as
fuel and works in CHP mode. Design and operating conditions of a
PEM fuel cell system is considered in this study. The energy
requirements of residential building and the number of fuel cell
stacks to meet them have been estimated. The method involved
exergy analysis and entropy generation thorough the months of the
year. Results show that all the energy needs of the building can be
met with 12 fuel cell stacks at a nominal capacity of 8.5 kW. Exergy
analysis of the CHP system shows that the increase in the ambient air
temperature from 1oC to 40oC, will have an increase of entropy
generation by 5.73%.Maximum entropy generates for 15 hour in 15th
of June and 15th of July is estimated to amount at 12624 (kW/K).
Entropy generation of this system through a year is estimated to
amount to 1004.54 GJ/k.year.
Abstract: Ovshinsky initiated scientific research in the field of
amorphous and disordered materials that continues to this day. The
Ovshinsky Effect where the resistance of thin GST films is
significantly reduced upon the application of low voltage is of
fundamental importance in phase-change - random access memory
(PC-RAM) devices.GST stands for GdSbTe chalcogenide type
glasses.However, the Ovshinsky Effect is not without controversy.
Ovshinsky thought the resistance of GST films is reduced by the
redistribution of charge carriers; whereas, others at that time including
many PC-RAM researchers today argue that the GST resistance
changes because the GST amorphous state is transformed to the
crystalline state by melting, the heat supplied by external heaters. In
this controversy, quantum mechanics (QM) asserts the heat capacity of
GST films vanishes, and therefore melting cannot occur as the heat
supplied cannot be conserved by an increase in GST film
temperature.By precluding melting, QM re-opens the controversy
between the melting and charge carrier mechanisms. Supporting
analysis is presented to show that instead of increasing GST film
temperature, conservation proceeds by the QED induced creation of
photons within the GST film, the QED photons confined by TIR. QED
stands for quantum electrodynamics and TIR for total internal
reflection. The TIR confinement of QED photons is enhanced by the
fact the absorbedheat energy absorbed in the GST film is concentrated
in the TIR mode because of their high surface to volume ratio. The
QED photons having Planck energy beyond the ultraviolet produce
excitons by the photoelectric effect, the electrons and holes of which
reduce the GST film resistance.
Abstract: A transient heat transfer mathematical model for the
prediction of temperature distribution in the car body during primer
baking has been developed by considering the thermal radiation and
convection in the furnace chamber and transient heat conduction
governing equations in the car framework. The car cockpit is
considered like a structure with six flat plates, four vertical plates
representing the car doors and the rear and front panels. The other
two flat plates are the car roof and floor. The transient heat
conduction in each flat plate is modeled by the lumped capacitance
method. Comparison with the experimental data shows that the heat
transfer model works well for the prediction of thermal behavior of
the car body in the curing furnace, with deviations below 5%.
Abstract: Unsteady magnetohydrodynamics (MHD) boundary
layer flow and heat transfer over a continuously stretching surface in
the presence of radiation is examined. By similarity transformation,
the governing partial differential equations are transformed to a set of
ordinary differential equations. Numerical solutions are obtained by
employing the Runge-Kutta-Fehlberg method scheme with shooting
technique in Maple software environment. The effects of
unsteadiness parameter, radiation parameter, magnetic parameter and
Prandtl number on the heat transfer characteristics are obtained and
discussed. It is found that the heat transfer rate at the surface
increases as the Prandtl number and unsteadiness parameter increase
but decreases with magnetic and radiation parameter.
Abstract: In this study, an analysis has been performed for
heat and mass transfer of a steady laminar boundary-layer flow
of a viscous flow past a nonlinearly stretching sheet.
Parameters n, Ec, k0, Sc represent the dominance of the
nonlinearly effect, viscous effect, radiation effect and mass
transfer effect which have presented in governing equations,
respectively. The similarity transformation and the
finite-difference method have been used to analyze the present
problem.
Abstract: In this paper, Zinc Oxide (ZnO) thin films are deposited on glass substrate by sol-gel method. The ZnO thin films with well defined orientation were acquired by spin coating of zinc acetate dehydrate monoethanolamine (MEA), de-ionized water and isopropanol alcohol. These films were pre-heated at 275°C for 10 min and then annealed at 350°C, 450°C and 550°C for 80 min. The effect of annealing temperature and different thickness on structure and surface morphology of the thin films were verified by Atomic Force Microscopy (AFM). It was found that there was a significant effect of annealing temperature on the structural parameters of the films such as roughness exponent, fractal dimension and interface width. Thin films also were characterizied by X-ray Diffractometery (XRD) method. XRD analysis revealed that the annealed ZnO thin films consist of single phase ZnO with wurtzite structure and show the c-axis grain orientation. Increasing annealing temperature increased the crystallite size and the c-axis orientation of the film after 450°C. Also In this study, ZnO thin films in different thickness have been prepared by sol-gel method on the glass substrate at room temperature. The thicknesses of films are 100, 150 and 250 nm. Using fractal analysis, morphological characteristics of surface films thickness in amorphous state were investigated. The results show that with increasing thickness, surface roughness (RMS) and lateral correlation length (ξ) are decreased. Also, the roughness exponent (α) and growth exponent (β) were determined to be 0.74±0.02 and 0.11±0.02, respectively.
Abstract: There was a high rate of corrosion in Pyrolysis
Gasoline Hydrogenation (PGH) unit of Arak Petrochemical Company
(ARPC), and it caused some operational problem in this plant. A
commercial chemical had been used as anti-corrosion in the
depentanizer column overhead in order to control the corrosion rate.
Injection of commercial corrosion inhibitor caused some
operational problems such as fouling in some heat exchangers. It was
proposed to replace this commercial material with another more
effective trouble free, and well-known additive by R&D and
operation specialists.
At first, the system was simulated by commercial simulation
software in electrolytic system to specify low pH points inside the
plant. After a very comprehensive study of the situation and technical
investigations ,ammonia / monoethanol amine solution was proposed
as neutralizer or corrosion inhibitor to be injected in a suitable point
of the plant. For this purpose, the depentanizer column and its
accessories system was simulated again in case of this solution
injection.
According to the simulation results, injection of new anticorrosion
substance has no any side effect on C5 cut product and
operating conditions of the column. The corrosion rate will be
cotrolled, if the pH remains at the range of 6.5 to 8 . Aactual plant
test run was also carried out by injection of ammonia / monoethanol
amine solution at the rate of 0.6 Kg/hr and the results of iron content
of water samples and corrosion test coupons confirmed the
simulation results.
Now, ammonia / monoethanol amine solution is injected to a
suitable pint inside the plant and corrosion rate has decreased
significantly.
Abstract: Accurate and comprehensive thermodynamic properties of pure and mixture of refrigerants are in demand by both producers and users of these materials. Information about thermodynamic properties is important initially to qualify potential candidates for working fluids in refrigeration machinery. From practical point of view, Refrigerants and refrigerant mixtures are widely used as working fluids in many industrial applications, such as refrigerators, heat pumps, and power plants The present work is devoted to evaluating seven cubic equations of state (EOS) in predicting gas and liquid phase volumetric properties of nine ozone-safe refrigerants both in super and sub-critical regions. The evaluations, in sub-critical region, show that TWU and PR EOS are capable of predicting PVT properties of refrigerants R32 within 2%, R22, R134a, R152a and R143a within 1% and R123, R124, R125, TWU and PR EOS's, from literature data are 0.5% for R22, R32, R152a, R143a, and R125, 1% for R123, R134a, and R141b, and 2% for R124. Moreover, SRK EOS predicts PVT properties of R22, R125, and R123 to within aforementioned errors. The remaining EOS's predicts volumetric properties of this class of fluids with higher errors than those above mentioned which are at most 8%.In general, the results are in favor of the preference of TWU and PR EOS over other remaining EOS's in predicting densities of all mentioned refrigerants in both super and sub critical regions. Typically, this refrigerant is known to offer advantages such as ozone depleting potential equal to zero, Global warming potential equal to 140, and no toxic.
Abstract: Utilization of bagasse ash for silica sources is one of
the most common application for agricultural wastes and valuable
biomass byproducts in sugar milling. The high percentage silica
content from bagasse ash was used as silica source for sodium
silicate solution. Different heating temperature, time and acid
treatment were studies for silica extraction. The silica was
characterized using various techniques including X-ray fluorescence,
X-ray diffraction, Scanning electron microscopy, and Fourier
Transform Infrared Spectroscopy method,. The synthesis conditions
were optimized to obtain the bagasse ash with the maximum silica
content. The silica content of 91.57 percent was achieved from
heating of bagasse ash at 600°C for 3 hours under oxygen feeding
and HCl treatment. The result can be used as value added for bagasse
ash utilization and minimize the environmental impact of disposal
problems.
Abstract: Pentachlorophenol (PCP) is a polychlorinated
aromatic compound that is widespread in industrial effluents and is
considered to be a serious pollutant. Among the variety of industrial
effluents encountered, effluents from tanning industry are very
important and have a serious pollution potential. PCP is also formed
unintentionally in effluents of paper and pulp industries. It is highly
persistent in soils and is lethal to a wide variety of beneficial
microorganisms and insects, human beings and animals. The natural
processes that breakdown toxic chemicals in the environment have
become the focus of much attention to develop safe and environmentfriendly
deactivation technologies. Microbes and plants are among
the most important biological agents that remove and degrade waste
materials to enable their recycling in the environment. The present
investigation was carried out with the aim of developing a microbial
system for bioremediation of PCP polluted soils. A number of plant
species were evaluated for their ability to tolerate different
concentrations of pentachlorophenol (PCP) in the soil. The
experiment was conducted for 30 days under pot culture conditions.
The toxic effect of PCP on plants was studied by monitoring seed
germination, plant growth and biomass. As the concentration of PCP
was increased to 50 ppm, the inhibition of seed germination, plant
growth and biomass was also increased. Although PCP had a
negative effect on all plant species tested, maize and groundnut
showed the maximum tolerance to PCP. Other tolerating crops
included wheat, safflower, sunflower, and soybean. From the
rhizosphere soil of the tolerant seedlings, as many as twenty seven
PCP tolerant bacteria were isolated. From soybean, 8; sunflower, 3;
safflower 8; maize 2; groundnut and wheat, 3 each isolates were
made. They were screened for their PCP degradation potentials.
HPLC analyses of PCP degradation revealed that the isolate MAZ-2
degraded PCP completely. The isolate MAZ-1 was the next best
isolate with 90 per cent PCP degradation. These strains hold promise
to be used in the bioremediation of PCP polluted soils.
Abstract: The hydrodynamic and thermal lattice Boltzmann
methods are applied to investigate the turbulent convective heat
transfer in the wavy channel flows. In this study, the turbulent
phenomena are modeling by large-eddy simulations with the
Smagorinsky model. As a benchmark, the laminar and turbulent
backward-facing step flows are simulated first. The results give good
agreement with other numerical and experimental data. For wavy
channel flows, the distribution of Nusselt number and the skin-friction
coefficients are calculated to evaluate the heat transfer effect and the
drag force. It indicates that the vortices at the trough would affect the
magnitude of drag and weaken the heat convection effects on the wavy
surface. In turbulent cases, if the amplitude of the wavy boundary is
large enough, the secondary vortices would be generated at troughs
and contribute to the heat convection. Finally, the effects of different
Re on the turbulent transport phenomena are discussed.
Abstract: This research was conducted to develop a correlation
between microstructure of HSLA steel and the mechanical properties
that occur as a result of both laser and mechanical forming processes
of the metal. The technique of forming flat metals by applying laser
beams is a relatively new concept in the manufacturing industry.
However, the effects of laser energy on the stability of metal alloy
phases have not yet been elucidated in terms of phase
transformations and microhardness. In this work, CO2 laser source
was used to irradiate the surface of a flat metal then the
microstructure and microhardness of the metal were studied on the
formed specimen. The extent to which the microstructure changed
depended on the heat inputs of up to 1000 J/cm2 with cooling rates of
about 4.8E+02 K/s. Experimental results revealed that the irradiated
surface of a HSLA steel had transformed to austenitic structure
during the heating process.
Abstract: The paper presents the influence of the conventional
ploughing tillage technology in comparison with the minimum
tillage, upon the soil properties, weed control and yield in the case of
maize (Zea mays L.), soya-bean (Glycine hispida L.) and winter
wheat (Triticum aestivum L.) in a three years crop rotation. A
research has been conducted at the University of Agricultural
Sciences and Veterinary Medicine Cluj-Napoca, Romania. The use of
minimum soil tillage systems within a three years rotation: maize,
soya-bean, wheat favorites the rise of the aggregates hydro stability
with 5.6-7.5% on a 0-20 cm depth and 5-11% on 20-30 cm depth.
The minimum soil tillage systems – paraplow, chisel or rotary grape
– are polyvalent alternatives for basic preparation, germination bed
preparation and sowing, for fields and crops with moderate loose
requirements being optimized technologies for: soil natural fertility
activation and rationalization, reduction of erosion, increasing the
accumulation capacity for water and realization of sowing in the
optimal period. The soil tillage system influences the productivity
elements of cultivated species and finally the productions thus
obtained. Thus, related to conventional working system, the
productions registered in minimum tillage working represented 89-
97% in maize, 103-112% in soya-bean, 93-99% in winter-wheat. The
results of investigations showed that the yield is a conclusion soil
tillage systems influence on soil properties, plant density assurance
and on weed control. Under minimum tillage systems in the case of
winter weat as an option for replacing classic ploughing, the best
results in terms of quality indices were obtained from version worked
with paraplow, followed by rotary harrow and chisel. At variants
worked with paraplow were obtained quality indices close to those of
the variant worked with plow, and protein and gluten content was
even higher. At Ariesan variety, highest protein content, 12.50% and
gluten, 28.6% was obtained for the variant paraplow.
Abstract: Because of importance of energy, optimization of
power generation systems is necessary. Gas turbine cycles are
suitable manner for fast power generation, but their efficiency is
partly low. In order to achieving higher efficiencies, some
propositions are preferred such as recovery of heat from exhaust
gases in a regenerator, utilization of intercooler in a multistage
compressor, steam injection to combustion chamber and etc.
However thermodynamic optimization of gas turbine cycle, even
with above components, is necessary. In this article multi-objective
genetic algorithms are employed for Pareto approach optimization of
Regenerative-Intercooling-Gas Turbine (RIGT) cycle. In the multiobjective
optimization a number of conflicting objective functions
are to be optimized simultaneously. The important objective
functions that have been considered for optimization are entropy
generation of RIGT cycle (Ns) derives using Exergy Analysis and
Gouy-Stodola theorem, thermal efficiency and the net output power
of RIGT Cycle. These objectives are usually conflicting with each
other. The design variables consist of thermodynamic parameters
such as compressor pressure ratio (Rp), excess air in combustion
(EA), turbine inlet temperature (TIT) and inlet air temperature (T0).
At the first stage single objective optimization has been investigated
and the method of Non-dominated Sorting Genetic Algorithm
(NSGA-II) has been used for multi-objective optimization.
Optimization procedures are performed for two and three objective
functions and the results are compared for RIGT Cycle. In order to
investigate the optimal thermodynamic behavior of two objectives,
different set, each including two objectives of output parameters, are
considered individually. For each set Pareto front are depicted. The
sets of selected decision variables based on this Pareto front, will
cause the best possible combination of corresponding objective
functions. There is no superiority for the points on the Pareto front
figure, but they are superior to any other point. In the case of three
objective optimization the results are given in tables.
Abstract: Imperfect transmission conditions modeling a thin reactive 2D interphases layer between two dissimilar bonded strips have been extracted. In this paper, the soundness of these transmission conditions for heat conduction problems are examined by the finite element method for a strong temperature-dependent source or sink and non-monotonic temperature distributions around the faces..