Abstract: In a nuclear reactor Loss of Coolant accident (LOCA)
considers wide range of postulated damage or rupture of pipe in the
heat transport piping system. In the case of LOCA with/without
failure of emergency core cooling system in a Pressurised Heavy
water Reactor, the Pressure Tube (PT) temperature could rise
significantly due to fuel heat up and gross mismatch of the heat
generation and heat removal in the affected channel. The extent and
nature of deformation is important from reactor safety point of view.
Experimental set-ups have been designed and fabricated to simulate
ballooning (radial deformation) of PT for 220 MWe IPHWRs.
Experiments have been conducted by covering the CT by ceramic
fibers and then by submerging CT in water of voided PTs. In both
the experiments, it is observed that ballooning initiates at a
temperature around 665´┐¢C and complete contact between PT and
Caldaria Tube (CT) occurs at around 700´┐¢C approximately. The
strain rate is found to be 0.116% per second. The structural integrity
of PT is retained (no breach) for all the experiments. The PT heatup
is found to be arrested after the contact between PT and CT, thus
establishing moderator acting as an efficient heat sink for IPHWRs.
Abstract: The authors report a case of swine urolithiasis caused
by improper administration of sulfamonomethoxine and which was
diagnosed by examination of urinary sediments and analyzing the
composition of the uroliths. The chemical composition of urinary
calculi obtained from affected pigs with urolithiasis was further
confimed as sulfamonomethoxine by fourier transform infrared
(FTIR). It is suggested that appearance of typical fanlike or wheat
bunchy crystals in urinary sediments under observation of lightmicroscope
and determination by FTIR for the crystals are helpful in
diagnosing sulfa calculi causced swine urolithiasis.
Abstract: The objective of this paper was to designing a
ventilation system to enhance the performance of roof solar collector
(RSC) for reducing heat accumulation inside the house. The RSC has
1.8 m2 surface area made of CPAC monier roof tiles on the upper part
and gypsum board on the lower part. The space between CPAC
monier and gypsum board was fixed at 14 cm.
Ventilation system of modified roof solar collector (modified
RSC) consists of 9 tubes of 0.15m diameter and installed in the
lower part of RSC. Experimental result showed that the temperature
of the room, and attic temperature. The average temperature
reduction of room of house used modified RSC is about 2oC. and the
percentage of room temperature reduction varied between 0 to 10%.
Therefore, modified RSC is an interesting option in the sense that it
promotes solar energy and conserve energy.
Abstract: The present study was designed to investigate the
cardio protective role of chronic oral administration of alcoholic
extract of Terminalia arjuna in in-vivo ischemic reperfusion injury
and the induction of HSP72. Rabbits, divided into three groups, and
were administered with the alcoholic extract of the bark powder of
Terminalia arjuna (TAAE) by oral gavage [6.75mg/kg: (T1) and
9.75mg/kg: (T2), 6 days /week for 12 weeks]. In open-chest
Ketamine pentobarbitone anaesthetized rabbits, the left anterior
descending coronary artery was occluded for 15 min of ischemia
followed by 60 min of reperfusion. In the vehicle-treated group,
ischemic-reperfusion injury (IRI) was evidenced by depression of
global hemodynamic function (MAP, HR, LVEDP, peak LV (+) & (-
) (dP/dt) along with depletion of HEP compounds. Oxidative stress
in IRI was evidenced by, raised levels of myocardial TBARS and
depletion of endogenous myocardial antioxidants GSH, SOD and
catalase. Western blot analysis showed a single band corresponding
to 72 kDa in homogenates of hearts from rabbits treated with both the
doses. In the alcoholic extract of the bark powder of Terminalia
arjuna treatment groups, both the doses had better recovery of
myocardial hemodynamic function, with significant reduction in
TBARS, and rise in SOD, GSH, catalase were observed. The results
of the present study suggest that the alcoholic extract of the bark
powder of Terminalia arjuna in rabbit induces myocardial HSP 72
and augments myocardial endogenous antioxidants, without causing
any cellular injury and offered better cardioprotection against
oxidative stress associated with myocardial IR injury.
Abstract: This paper considers the effect of heat generation
proportional l to (T - T∞ )p , where T is the local temperature and T∞
is the ambient temperature, in unsteady free convection flow near the
stagnation point region of a three-dimensional body. The fluid is
considered in an ambient fluid under the assumption of a step change
in the surface temperature of the body. The non-linear coupled partial
differential equations governing the free convection flow are solved
numerically using an implicit finite-difference method for different
values of the governing parameters entering these equations. The
results for the flow and heat characteristics when p ≤ 2 show that
the transition from the initial unsteady-state flow to the final steadystate
flow takes place smoothly. The behavior of the flow is seen
strongly depend on the exponent p.
Abstract: Inorganic nanoparticles filled polymer composites
have extended their multiple functionalities to various applications,
including mechanical reinforcement, gas barrier, dimensional
stability, heat distortion temperature, flame-retardant, and thermal
conductivity. Sodium stearate-modified calcium carbonate (CaCO3)
nanoparticles were prepared using surface modification method. The
results showed that sodium stearate attached to the surface of CaCO3
nanoparticles with the chemical bond. The effect of modified CaCO3
nanoparticles on thermal properties of polypropylene (PP) was
studied by means of differential scanning calorimetry (DSC) and
Thermogravimetric analysis (TGA). It was found that CaCO3
significantly affected the crystallization temperature and
crystallization degree of PP. Effect of the modified CaCO3 content on
mechanical properties of PP/CaCO3 nanocomposites was also
studied. The results showed that the modified CaCO3 can effectively
improve the mechanical properties of PP. In comparison with PP, the
impact strength of PP/CaCO3 nanocomposites increased by about
65% and the hardness increased by about 5%.
Abstract: Conjugate natural convection in a differentially heated
square enclosure containing a polygon shaped object is studied numerically in this article. The effect of various polygon types on the
fluid flow and thermal performance of the enclosure is addressed for
different thermal conductivities. The governing equations are modeled
and solved numerically using the built-in finite element method of COMSOL software. It is found that the heat transfer rate remains
stable by varying the polygon types.
Abstract: Nigerian bread is baked with vitamin A fortified wheat flour. Study aimed at determining its contribution to preschoolers- vitamin A nutriture. A cross-sectional/experimental study was carried out in four poor-urban Local Government Areas (LGAs) of Metropolitan Lagos, Nigeria. A pretested food frequency questionnaire was administered to randomly selected mothers of 1600 preschoolers (24-59 months). Retinyl Palmitate content of fourteen bread samples randomly collected from bakeries in all LGAs was analyzed at 0 and 5 days at 25oC using High Performance Liquid Chromatography. Data analysis was done at p
Abstract: The research object was wheat bread. Experiments
were carried out at the Faculty of Food Technology of the Latvia
University of Agriculture. An active packaging in combination with
modified atmosphere (MAP, CO2 60% and N2 40%) was examined
and compared with traditional packaging in air ambiance. Polymer
Multibarrier 60, PP and OPP bags were used. Influence of iron based
oxygen absorber in sachets of 100 cc obtained from Mitsubishi Gas
Chemical Europe Ageless® was tested on the quality during the shelf
of wheat bread. Samples of 40±4 g were packaged in polymer
pouches (110 mm x 120 mm), hermetically sealed by MULTIVAC
C300 vacuum chamber machine, and stored in room temperature
+21.0±0.5 °C. The physiochemical properties – weight losses,
moisture content, hardness, pH, colour, changes of atmosphere
content (CO2 and O2) in headspace of packs, and microbial
conditions were analysed before packaging and in the 7th, 14th, 21st
and 28th days of storage.
Abstract: The aim of the present work is to study the effect of annealing on the vibration damping capacity of high-chromium (16%) ferromagnetic steel. The alloys were prepared from raw materials of 99.9% purity melted in a high frequency induction furnace under high vacuum. The samples were heat-treated in vacuum at various temperatures (800 to 1200ºC) for 1 hour followed by slow cooling (120ºC/h). The inverted torsional pendulum method was used to evaluate the vibration damping capacity. The results indicated that the vibration damping capacity of the alloys is influenced by annealing and there exists a critical annealing temperature after 1000ºC. The damping capacity increases quickly below the critical temperature since the magnetic domains move more easily.
Abstract: We have devised a thermal carpet cloak theoretically
and implemented in silicon using layered metamaterial. The layered
metamaterial is composed of single crystalline silicon and its phononic
crystal. The design is based on a coordinate transformation. We
demonstrate the result with numerical simulation. Great cloaking
performance is achieved as a thermal insulator is well hidden under the
thermal carpet cloak. We also show that the thermal carpet cloak can
even the temperature on irregular surface. Using thermal carpet cloak
to manipulate the heat conduction is effective because of its low
complexity.
Abstract: This paper looks into detailed investigation of
thermal-hydraulic characteristics of the flow field in a fuel rod
model, especially near the spacer. The area investigate represents a
source of information on the velocity flow field, vortex, and on the
amount of heat transfer into the coolant all of which are critical for
the design and improvement of the fuel rod in nuclear power plants.
The flow field investigation uses three-dimensional Computational
Fluid Dynamics (CFD) with the Reynolds stresses turbulence model
(RSM). The fuel rod model incorporates a vertical annular channel
where three different shapes of spacers are used; each spacer shape is
addressed individually. These spacers are mutually compared in
consideration of heat transfer capabilities between the coolant and
the fuel rod model. The results are complemented with the calculated
heat transfer coefficient in the location of the spacer and along the
stainless-steel pipe.
Abstract: In this paper, in order to investigate the effects of
photovoltaic system introduction to detached houses in Japan, two
kinds of works were done. Firstly, the hourly generation amount of a
4.2kW photovoltaic system were simulated in 46 cities to investigate
the potential of the system in different regions in Japan using a
simulation model of photovoltaic system. Secondly, based on the
simulated electricity generation amount, the energy saving, the
environmental and the economic effect of the photovoltaic system
were examined from hourly to annual timescales, based upon
calculations of typical electricity, heating, cooling and hot water
supply load profiles for Japanese dwellings. The above analysis was
carried out using a standard year-s hourly weather data for the
different city provided by the Expanded AMeDAS Weather Data
issued by AIJ (Architectural Institute of Japan).
Abstract: The malfunction of thermal protection system (TPS) caused by aerodynamic heating is a latent trouble to aircraft structure safety. Accurately predicting the structure temperature field is quite important for the TPS design of hypersonic vehicle. Since Thornton’s work in 1988, the coupled method of aerodynamic heating and heat transfer has developed rapidly. However, little attention has been paid to the influence of structural deformation on aerodynamic heating and structural temperature field. In the flight, especially the long-endurance flight, the structural deformation, caused by the aerodynamic heating and temperature rise, has a direct impact on the aerodynamic heating and structural temperature field. Thus, the coupled interaction cannot be neglected. In this paper, based on the method of static aero-thermo-elasticity, considering the influence of aero-thermo-elasticity deformation, the aerodynamic heating and heat transfer coupled results of hypersonic vehicle wing model were calculated. The results show that, for the low-curvature region, such as fuselage or center-section wing, structure deformation has little effect on temperature field. However, for the stagnation region with high curvature, the coupled effect is not negligible. Thus, it is quite important for the structure temperature prediction to take into account the effect of elastic deformation. This work has laid a solid foundation for improving the prediction accuracy of the temperature distribution of aircraft structures and the evaluation capacity of structural performance.
Abstract: The aim of this research was to calculate the thermal
properties of Au3Ni Nanowire. The molecular dynamics (MD)
simulation technique was used to obtain the effect of radius size on
the energy, the melting temperature and the latent heat of fusion at
the isobaric-isothermal (NPT) ensemble. The Quantum Sutton-Chen
(Q-SC) many body interatomic potentials energy have been used for
Gold (Au) and Nickel (Ni) elements and a mixing rule has been
devised to obtain the parameters of these potentials for nanowire
stats. Our MD simulation results show the melting temperature and
latent heat of fusion increase upon increasing diameter of nanowire.
Moreover, the cohesive energy decreased with increasing diameter of
nanowire.
Abstract: The mixed oxide nuclear fuel (MOX) of U and Pu contains several percent of fission products and minor actinides, such as neptunium, americium and curium. It is important to determine accurately the decay heat from Curium isotopes as they contribute significantly in the MOX fuel. This heat generation can cause samples to melt very quickly if excessive quantities of curium are present. In the present paper, we introduce a new approach that can predict the decay heat from curium isotopes. This work is a part of the project funded by King Abdulaziz City of Science and Technology (KASCT), Long-Term Comprehensive National Plan for Science, Technology and Innovations, and take place in King Abdulaziz University (KAU), Saudi Arabia. The approach is based on the numerical solution of coupled linear differential equations that describe decays and buildups of many nuclides to calculate the decay heat produced after shutdown. Results show the consistency and reliability of the approach applied.
Abstract: Thermal behavior of fuel channel under loss of coolant accident (LOCA) is a major concern for nuclear reactor safety. LOCA along with failure of emergency cooling water system (ECC) may leads to mechanical deformations like sagging and ballooning. In order to understand the phenomenon an experiment has been carried out using 19 pin fuel element simulator. Main purpose of the experiment was to trace temperature profiles over the pressure tube, calandria tube and clad tubes of Indian Pressurized Heavy Water Reactor (IPHWR) under symmetrical and asymmetrical heat-up conditions. For simulating the fully voided scenario, symmetrical heating of pressure was carried out by injecting 13.2 KW (2 % of nominal power) to all the 19 pins and the temperatures of pressure tube, calandria tube and clad tubes were measured. During symmetrical heating the sagging of fuel channel was initiated at 460 °C and the highest temperature attained by PT was 650 °C . The decay heat from clad tubes was dissipated to moderator mainly by radiation and natural convection. The highest temperature of 680 °C was observed over the outer ring of clad tubes of fuel simulator. Again, to simulate partially voided condition, asymmetrical heating of pressure was carried out by supplying 8.0 kW power to upper 8 pins of fuel simulator and temperature profiles were measured. Along the circumference of pressure tube (PT) the highest temperature difference of 320 °C was observed, which highlights the magnitude of thermal stresses under partially voided conditions.
Abstract: This study numerically investigates the effects of Electrohydrodynamic on flow patterns and heat transfer enhancement within a cavity which is on the lower wall of channel. In this simulation, effects of using ground wire and ground plate on the flow patterns are compared. Moreover, the positions of electrode wire respecting with ground are tested in the range of angles θ = 0 - 180o. High electrical voltage exposes to air is 20 kV. Bulk mean velocity and temperature of inlet air are controlled at 0.1 m/s and 60 OC, respectively. The result shows when electric field is applied, swirling flow is appeared in the channel. In addition, swirling flow patterns in the main flow of using ground plate are widely spreader than that of using ground wire. Moreover, direction of swirling flow also affects the flow pattern and heat transfer in a cavity. These cause the using ground wire to give the maximum temperature and heat transfer higher than using ground plate. Furthermore, when the angle is at θ = 60o, high shear flow effect is obtained. This results show high strength of swirling flow and effective heat transfer enhancement.
Abstract: Hydrogenated biodiesel is one of the most promising
renewable fuels. It has many advantages over conventional biodiesel,
including higher cetane number, higher heating value, lower
viscosity, and lower corrosiveness due to its absence of oxygen.
From previous work, Pd/TiO2 gave high conversion and selectivity in
hydrogenated biodiesel. In this work, the effect of biomass feedstocks
(i.e. beef fat, chicken fat, pork fat, and jatropha oil) on the production
of hydrogenated biodiesel over Pd/TiO2 has been studied. Biomass
feedstocks were analyzed by ICP-OES (inductively coupled plasma
optical emission spectrometry) to identify the content of impurities
(i.e. P, K, Ca, Na, and Mg). The deoxygenation catalyst, Pd/TiO2,
was prepared by incipient wetness impregnation (IWI) and tested in a
continuous flow packed-bed reactor at 500 psig, 325°C, H2/feed
molar ratio of 30, and LHSV of 4 h-1 for its catalytic activity and
selectivity in hydrodeoxygenation. All feedstocks gave high
selectivity in diesel specification range hydrocarbons and the main
hydrocarbons were n-pentadecane (n-C15) and n-heptadecane (n-
C17), resulting from the decarbonylation/decarboxylation reaction.
Intermediates such as oleic acid, stearic acid, palmitic acid, and esters
were also detected in minor amount. The conversion of triglycerides
in jatropha oil is higher than those of chicken fat, pork fat, and beef
fat, respectively. The higher concentration of metal impurities in
feedstock, the lower conversion of feedstock.
Abstract: It is very important to determine reference temperature when convective temperature because it should be used to calculate the temperature potential. This paper deals with the development of a new method that can determine heat transfer coefficient and reference free stream temperature simultaneously, based on transient heat transfer experiments with using two narrow band thermo-tropic liquid crystals (TLC's). The method is validated through error analysis in terms of the random uncertainties in the measured temperatures. It is shown how the uncertainties in heat transfer coefficient and free stream temperature can be reduced. The general method described in this paper is applicable to many heat transfer models with unknown free stream temperature.