Abstract: Renewed interest in propeller propulsion on aircraft
configurations combined with higher propeller loads lead to the question how the effects of the propulsion on model support disturbances
should be accounted for. In this paper, the determination of engine power effects on support interference of sting-mounted models is
demonstrated by a measurement on a four-engine turboprop aircraft.
CFD results on a more generic model are presented in order to clarify
the possible mechanism behind engine power effects on support
interference. The engine slipstream induces a local change in angle
of sideslip at the model sting thereby influencing the sting near-field and far-field effects. Whether or not the net result of these changes
in the disturbance pattern leads to a significant engine power effect depends on the configuration of the wind tunnel model and the test
setup.
Abstract: This paper presents a multi-objective order allocation
planning problem with the consideration of various real-world
production features. A novel hybrid intelligent optimization model,
integrating a multi-objective memetic optimization process, a Monte
Carlo simulation technique and a heuristic pruning technique, is
proposed to handle this problem. Experiments based on industrial data
are conducted to validate the proposed model. Results show that (1)
the proposed model can effectively solve the investigated problem by
providing effective production decision-making solutions, which
outperformsan NSGA-II-based optimization process and an industrial
method.
Abstract: This paper presented two new efficient algorithms
for contour approximation. The proposed algorithm is compared
with Ramer (good quality), Triangle (faster) and Trapezoid (fastest)
in this work; which are briefly described. Cartesian co-ordinates of
an input contour are processed in such a manner that finally
contours is presented by a set of selected vertices of the edge of the
contour. In the paper the main idea of the analyzed procedures for
contour compression is performed. For comparison, the mean
square error and signal-to-noise ratio criterions are used.
Computational time of analyzed methods is estimated depending on
a number of numerical operations. Experimental results are
obtained both in terms of image quality, compression ratios, and
speed. The main advantages of the analyzed algorithm is small
numbers of the arithmetic operations compared to the existing
algorithms.
Abstract: The aim of this study was to remove the two principal
noises which disturb the surface electromyography signal
(Diaphragm). These signals are the electrocardiogram ECG artefact
and the power line interference artefact. The algorithm proposed
focuses on a new Lean Mean Square (LMS) Widrow adaptive
structure. These structures require a reference signal that is correlated
with the noise contaminating the signal. The noise references are
then extracted : first with a noise reference mathematically
constructed using two different cosine functions; 50Hz (the
fundamental) function and 150Hz (the first harmonic) function for
the power line interference and second with a matching pursuit
technique combined to an LMS structure for the ECG artefact
estimation. The two removal procedures are attained without the use
of supplementary electrodes. These techniques of filtering are
validated on real records of surface diaphragm electromyography
signal. The performance of the proposed methods was compared with
already conducted research results.
Abstract: The experiment was then conducted to investigate the
effect of cassava peel addition in the concentrate on the performance
of lactating dairy cows. Twenty four Holstein Friesian crossbred
(>87.5% Holstein Friesian) lactating dairy cows in mid lactation;
averaging 12.2+2.1 kg of milk, 119+45 days in milk, 44.1+6.2
months old and 449+33 kg live weight, were stratified for milk yield,
days in milk, age, stage of lactation and body weight, and then
randomly allocated to three treatment groups. The first, second and
third groups were fed concentrates containing the respective cassava
peel, 0, 20 and 40%. All cows were fed ad libitum corn silage and
freely access to clean water. Dry matter intake, 4%FCM, milk
composition and body weight change were affected (P
Abstract: Information Technology (IT) projects are always
accompanied by various risks and because of high rate of failure in
such projects, managing risks in order to neutralize or at least
decrease their effects on the success of the project is strongly
essential. In this paper, fuzzy analytical hierarchy process (FAHP) is
exploited as a means of risk evaluation methodology to prioritize and
organize risk factors faced in IT projects. A real case of IT projects, a
project of design and implementation of an integrated information
system in a vehicle producing company in Iran is studied. Related
risk factors are identified and then expert qualitative judgments about
these factors are acquired. Translating these judgments to fuzzy
numbers and using them as an input to FAHP, risk factors are then
ranked and prioritized by FAHP in order to make project managers
aware of more important risks and enable them to adopt suitable
measures to deal with these highly devastative risks.
Abstract: This study was conducted to determine the
effect of abdominal exercises versus abdominal supporting
belt on abdominal efficiency and inter-recti separation
following vaginal delivery.30 primiparous post-natal women
participated in this study. Their age ranged from (25 - 35)
years and their BMI < 30 Kg/m2. Participants were assigned
randomly into 2groups, participants of group (A) used
abdominal belt from the 2nd day following delivery, till the end
of puerperium (6 weeks), while participants of group (B)
engaged into abdominal exercises program from the 2nd day
following delivery for 6 weeks. The results of the present
study revealed that although there was no statistical difference
in waist circumference between both groups, participation in
abdominal exercise program produced a pronounced reduction
in waist/hip ratio, and inter-recti separation and also caused
significant increase in abdominal muscles strength (peak
torque, maximum repetition total work and average power)
higher than the use of abdominal belt.
Abstract: Self-compacting concrete (SCC), a new kind of high
performance concrete (HPC) have been first developed in Japan in
1986. The development of SCC has made casting of dense
reinforcement and mass concrete convenient, has minimized noise.
Fresh self-compacting concrete (SCC) flows into formwork and
around obstructions under its own weight to fill it completely and
self-compact (without any need for vibration), without any
segregation and blocking. The elimination of the need for
compaction leads to better quality concrete and substantial
improvement of working conditions. SCC mixes generally have a
much higher content of fine fillers, including cement, and produce
excessively high compressive strength concrete, which restricts its
field of application to special concrete only. To use SCC mixes in
general concrete construction practice, requires low cost materials to
make inexpensive concrete.
Rice husk ash (RHA) has been used as a highly reactive
pozzolanic material to improve the microstructure of the interfacial
transition zone (ITZ) between the cement paste and the aggregate in
self compacting concrete. Mechanical experiments of RHA blended
Portland cement concretes revealed that in addition to the pozzolanic
reactivity of RHA (chemical aspect), the particle grading (physical
aspect) of cement and RHA mixtures also exerted significant
influences on the blending efficiency.
The scope of this research was to determine the usefulness of Rice
husk ash (RHA) in the development of economical self compacting
concrete (SCC). The cost of materials will be decreased by reducing
the cement content by using waste material like rice husk ash instead
of.
This paper presents a study on the development of Mechanical
properties up to 180 days of self compacting and ordinary concretes
with rice-husk ash (RHA), from a rice paddy milling industry in
Rasht (Iran). Two different replacement percentages of cement by
RHA, 10%, and 20%, and two different water/cementicious material
ratios (0.40 and 0.35), were used for both of self compacting and
normal concrete specimens. The results are compared with those of
the self compacting concrete without RHA, with compressive,
flexural strength and modulus of elasticity. It is concluded that RHA
provides a positive effect on the Mechanical properties at age after
60 days.
Base of the result self compacting concrete specimens have higher
value than normal concrete specimens in all test except modulus of
elasticity. Also specimens with 20% replacement of cement by RHA
have the best performance.
Abstract: This paper focuses on robust design and optimization
of industrial production wastes. Past literatures were reviewed to case
study Clamason Industries Limited (CIL) - a leading ladder-tops
manufacturer. A painstaking study of the firm-s practices at the shop
floor revealed that Over-production, Waiting time, Excess inventory,
and Defects are the major wastes that are impeding their progress and
profitability. Design expert8 software was used to apply Taguchi
robust design and response surface methodology in order to model,
analyse and optimise the wastes cost in CIL. Waiting time and overproduction
rank first and second in contributing to the costs of wastes
in CIL. For minimal wastes cost the control factors of overproduction,
waiting-time, defects and excess-inventory must be set at
0.30, 390.70, 4 and 55.70 respectively for CIL. The optimal value of
cost of wastes for the months studied was 22.3679. Finally, a
recommendation was made that for the company to enhance their
profitability and customer satisfaction, they must adopt the Shingeo
Shingo-s Single Minute Exchange of Dies (SMED), which will
immediately tackle the waste of waiting by drastically reducing their
setup time.
Abstract: Chronic hepatitis B can evolve to cirrhosis and liver
cancer. Interferon is the only effective treatment, for carefully selected
patients, but it is very expensive. Some of the selection criteria are
based on liver biopsy, an invasive, costly and painful medical procedure.
Therefore, developing efficient non-invasive selection systems,
could be in the patients benefit and also save money. We investigated
the possibility to create intelligent systems to assist the Interferon
therapeutical decision, mainly by predicting with acceptable accuracy
the results of the biopsy. We used a knowledge discovery in integrated
medical data - imaging, clinical, and laboratory data. The resulted
intelligent systems, tested on 500 patients with chronic hepatitis
B, based on C5.0 decision trees and boosting, predict with 100%
accuracy the results of the liver biopsy. Also, by integrating the other
patients selection criteria, they offer a non-invasive support for the
correct Interferon therapeutic decision. To our best knowledge, these
decision systems outperformed all similar systems published in the
literature, and offer a realistic opportunity to replace liver biopsy in
this medical context.
Abstract: Anaerobic treatment has many advantages over other
biological method particularly when used to treat complex
wastewater such as petroleum refinery wastewater. In this study two
Up-flow Anaerobic Sludge Blanket (UASB) reactors were operated
in parallel to treat six volumetric organic loads (0.58, 1.21, 0.89,
2.34, 1.47 and 4.14 kg COD/m3·d) to evaluate the chemical oxygen
demand (COD) removal efficiency. The reactors were continuously
adapting to the changing of operation condition with increase in the
removal efficiency or slight decrease until the last load which was
more than two times the load, at which the reactor stressed and the
removal efficiency decreased to 75% with effluent concentration of
1746 mg COD/L. Other parameters were also monitored such as pH,
alkalinity, volatile fatty acid and gas production rate. The UASB
reactor was suitable to treat petroleum refinery wastewater and the
highest COD removal rate was 83% at 1215 kg/m3·d with COD
concentration about 356 mg/L in the effluent.
Abstract: Reference point effects of top managers exerts an influence on managerial decision-making behaviors. We introduces the main idea of developing the decision behavior testing system designed for top manager in team task circumstance. According to the theory of the reference point effect, study of testing experiments in the reference point effect is carried out. Under managerial decision-making simulation environment, a platform is designed for testing reference point effect. The system uses the outcome of the value of the reference point to report the characteristics of the decision behavior of top managers.
Abstract: The submitted paper deals with the problems of
trapping and enriching the gases and aerosols of the substances to be
determined in the ambient atmosphere. Further, the paper is focused
on the working principle of the miniaturized portable continuous
concentrator we have designed and the possibilities of its
application in air sampling and accumulation of organic and
inorganic substances with which the air is contaminated. The stress is
laid on trapping vapours and aerosols of solid substances with the
comparatively low vapour tension such as explosive compounds.
Abstract: Amarindra-vinitchai-mahaisuraya Bhiman throne hall
is one of the most significant throne halls in the grand palace in the
Ratthanakosin city situated in Bangkok, Thailand. This is the first
group of throne halls built in order to serve as a place for meetings,
performing state affairs and royal duties until the present time. The
structure and pattern of architectural design including the decoration
and interior design of the throne hall obviously exhibits and convey
the status of the king under the context of Thai society in the early
period of Ratthanakosin era. According to the tradition of ruling the
kingdom in absolute monarchy which had been in place since
Ayutthaya era (A.D.1350-1767), the king was deemed as Deva Raja,
the highest power and authority over the kingdom and as the greatest
emperor of the universe (Chakkravatin). The architectural design
adopted the concept of “Prasada" or Viman which served as the
dwelling place of the gods and was presented in the form of “Thai
traditional architecture" For the interior design of the throne hall, it
had been adopted to be the heaven and the centre of the Universe in
line with the cosmological beliefs of ancient people described in
scripture Tribhumikatha (Tri Bhumi) written by Phra Maha Thamma
Raja (Phraya Lithai) of the Sukhothai era (A.D.1347-1368).
According to this belief, the throne hall had been designed to represent
mount Meru, the central of the universe. On the top end of Mount
Meru is situated the Viman and dwelling place of Indra who is the king
of gods according to the idea of Deva Raja (the king god Avatar). At
the same time, Indra also existed as the king of the universe
simultaneously.
Abstract: This paper proposes an innovative methodology for
Acceptance Sampling by Variables, which is a particular category of
Statistical Quality Control dealing with the assurance of products
quality. Our contribution lies in the exploitation of machine learning
techniques to address the complexity and remedy the drawbacks of
existing approaches. More specifically, the proposed methodology
exploits Artificial Neural Networks (ANNs) to aid decision making
about the acceptance or rejection of an inspected sample. For any
type of inspection, ANNs are trained by data from corresponding
tables of a standard-s sampling plan schemes. Once trained, ANNs
can give closed-form solutions for any acceptance quality level and
sample size, thus leading to an automation of the reading of the
sampling plan tables, without any need of compromise with the
values of the specific standard chosen each time. The proposed
methodology provides enough flexibility to quality control engineers
during the inspection of their samples, allowing the consideration of
specific needs, while it also reduces the time and the cost required for
these inspections. Its applicability and advantages are demonstrated
through two numerical examples.
Abstract: We study the performance of compressed beamforming
weights feedback technique in generalized triangular decomposition
(GTD) based MIMO system. GTD is a beamforming technique that
enjoys QoS flexibility. The technique, however, will perform at its
optimum only when the full knowledge of channel state information
(CSI) is available at the transmitter. This would be impossible in
the real system, where there are channel estimation error and limited
feedback. We suggest a way to implement the quantized beamforming
weights feedback, which can significantly reduce the feedback data,
on GTD-based MIMO system and investigate the performance of
the system. Interestingly, we found that compressed beamforming
weights feedback does not degrade the BER performance of the
system at low input power, while the channel estimation error
and quantization do. For comparison, GTD is more sensitive to
compression and quantization, while SVD is more sensitive to the
channel estimation error. We also explore the performance of GTDbased
MU-MIMO system, and find that the BER performance starts
to degrade largely at around -20 dB channel estimation error.
Abstract: Recently, the findings on the MEG iterative scheme has demonstrated to accelerate the convergence rate in solving any system of linear equations generated by using approximation equations of boundary value problems. Based on the same scheme, the aim of this paper is to investigate the capability of a family of four-point block iterative methods with a weighted parameter, ω such as the 4 Point-EGSOR, 4 Point-EDGSOR, and 4 Point-MEGSOR in solving two-dimensional elliptic partial differential equations by using the second-order finite difference approximation. In fact, the formulation and implementation of three four-point block iterative methods are also presented. Finally, the experimental results show that the Four Point MEGSOR iterative scheme is superior as compared with the existing four point block schemes.
Abstract: The article deals with pneumatic and hot wire
anemometry measurement on subsonic axi-symmetric air ejector.
Performances of the ejector with and without pulsations of primary
flow are compared, measuring of characteristic pressures and mass
flow rates are performed and ejector efficiency is evaluated. The
pulsations of primary flow are produced by a synthetic jet generator,
which is placed in the supply line of the primary flow just in front of
the primary nozzle. The aim of the pulsation is to intensify the
mixing process. In the article we present: Pressure measuring of
pulsation on the mixing chamber wall, behind the mixing chamber
and behind the diffuser measured by fast pressure transducers and
results of hot wire anemometry measurement. It was found out that
using of primary flow pulsations yields higher back pressure behind
the ejector and higher efficiency. The processes in this ejector and
influences of primary flow pulsations on the mixing processes are
described.
Abstract: The design of an active leg orthosis for tumble
protection is proposed in this paper. The orthosis would be applied to
assist elders or invalids in rebalancing while they fall unexpectedly.
We observe the regain balance motion of healthy and youthful people,
and find the difference to elders or invalids. First, the physical model
of leg would be established, and we consider the leg motions are
achieve through four joints (phalanx stem, ankle, knee, and hip joint)
and five links (phalanges, talus, tibia, femur, and hip bone). To
formulate the dynamic equations, the coordinates which can clearly
describe the position in 3D space are first defined accordance with the
human movement of leg, and the kinematics and dynamics of the leg
movement can be formulated based on the robotics. For the purpose,
assisting elders and invalids in avoiding tumble, the posture variation
of unbalance and regaining balance motion are recorded by the
motion-capture image system, and the trajectory is taken as the desire
one. Then we calculate the force and moment of each joint based on
the leg motion model through programming MATLAB code. The
results would be primary information of the active leg orthosis design
for tumble protection.
Abstract: The indistinctness of the manufacturing processes makes that a parts cannot be realized in an absolutely exact way towards the specifications on the dimensions. It is thus necessary to assume that the effectively realized product has to belong in a very strict way to compatible intervals with a correct functioning of the parts. In this paper we present an approach based on mixing tow different characteristics theories, the fuzzy system and Petri net system. This tool has been proposed to model and control the quality in an assembly system. A robust command of a mechanical assembly process is presented as an application. This command will then have to maintain the specifications interval of parts in front of the variations. It also illustrates how the technique reacts when the product quality is high, medium, or low.