Abstract: Three dimensional analysis of thermal model in laser
full penetration welding, Nd:YAG, by transparent mode DP600 alloy
steel 1.25mm of thickness and gap of 0.1mm. Three models studied
the influence of thermal dependent temperature properties, thermal
independent temperature and the effect of peak value of specific heat
at phase transformation temperature, AC1, on the transient
temperature. Another seven models studied the influence of
discretization, meshes on the temperature distribution in weld plate.
It is shown that for the effects of thermal properties, the errors less
4% of maximum temperature in FZ and HAZ have identified. The
minimum value of discretization are at least one third increment per
radius for temporal discretization and the spatial discretization
requires two elements per radius and four elements through thickness
of the assembled plate, which therefore represent the minimum
requirements of modeling for the laser welding in order to get
minimum errors less than 5% compared to the fine mesh.
Abstract: The subject of the paper is comparative analysis of the hotel guest-s contractual liability for breaching the obligation for non-payment of hotel services in the hotel-keeper-s contract. The paper is methodologically conceived of six chapters (1. introduction, 2. comparative law sources of the hotel-keeper-s contract, 3. the guest-s obligation for payment of hotel services, 4. hotel guest's liability for non-payment, 5. the hotel-keeper-s rights due to nonpayment and 6. conclusion), which analyzes the guest-s liability for non-payment of hotel services through the international law, European law, euro-continental national laws (France, Germany, Italy, Croatia) and Anglo-American national laws (UK, USA). The paper-s results are the synthesis of answers to the set hypothesis and comparative review of hotel guest-s contractual liability for nonpayment of hotel services provided. In conclusion, it is necessary to adopt an international convention on the hotel-keeper-s contract, which would unify the institute of the hotel guest-s contractual liability for non-payment of hotel services at the international level.
Abstract: The technique of inducing micro ecosystem
restoration is one of aquatic ecology engineering methods used to
retrieve the polluted water. Batch scale study, pilot plant study, and
field study were carried out to observe the eutrophication using the
Inducing Ecology Restorative Symbiosis Agent (IERSA) consisting
mainly degraded products by using lactobacillus, saccharomycete,
and phycomycete. The results obtained from the experiments of the
batch scale and pilot plant study allowed us to development the
parameters for the field study. A pond, 5 m to the outlet of a lake,
with an area of 500 m2 and depth of 0.6-1.2 m containing about 500
tons of water was selected as a model. After the treatment with 10
mg IERSA/L water twice a week for 70 days, the micro restoration
mechanisms consisted of three stages (i.e., restoration, impact
maintenance, and ecology recovery experiment after impact). The
COD, TN, TKN, and chlorophyll a were reduced significantly in the
first week. Although the unexpected heavy rain and contaminate
from sewage system might slow the ecology restoration. However,
the self-cleaning function continued and the chlorophyll a reduced
for 50% in one month. In the 4th week, amoeba, paramecium, rotifer,
and red wriggle worm reappeared, and the number of fish flies
appeared up to1000 fish fries/m3. Those results proved that inducing
restorative mechanism can be applied to improve the eutrophication
and to control the growth of algae in the lakes by gaining the selfcleaning
through inducing and competition of microbes. The
situation for growth of fishes also can reach an excellent result due to
the improvement of water quality.
Abstract: This study aims to explore the differences and
similarities in perceptions of affective climate antecedents at the
workplace (intimacy, flexibility, employment stability, and team)
among Japanese and Thai Generations X and Y. The samples in this
study were Thai and Japanese workers who completed a work
environment questionnaire and provided demographic information.
Generational differences in perceptions (beliefs) of what factors
contribute to affective climate were investigated using t-test analysis.
Mean scores for each antecedent were ranked to determine how each
generation in each group prioritized the importance of all affective
climate antecedents. Japanese Generation Y perceived the importance
of employment stability for affective climate of their workplaces to be
significantly higher than did Japanese Generation X. Thai Generation
Y considered flexibility with a higher priority than did Thai
Generation X. Intimacy was perceived as highly important across
generations and countries in regard to affective climate. Results
suggest that managers should design workplaces for a mixture of
diverse generations, resulting in a better affective climate. Differences
in the importance of antecedents for affective climate among
Generations X and Y in two countries were clarified. In addition,
different preferences regarding work environment across Japanese
Generations X and Y and Thai Generations X and Y were discussed.
Abstract: The main purpose of this study is to analyze the
relationship of leisure agriculture park visitors on tourist destination
image, environmental perception, travel experiences and revisiting
willingness. This study used questionnaires to Xinshe leisure
agriculture park visitors- targeted convenience sampling manner total
of 636 valid questionnaires. Valid questionnaires by descriptive
statistics, correlation analysis and multiple regression analysis, the
study found that: 1. The agricultural park visitors- correlations exist
between the destination image, perception of the environment, tourism
experience and revisiting willingness. 2."Excellent facilities and
services", "space atmosphere comfortable" and "the spacious paternity
outdoor space" imagery, of visitors- "revisiting willingness predict. 3.
Visitors- in leisure agriculture park "environmental perception" and
"travel experience, future revisiting willingness predict. According to
the analysis of the results, the study not only operate on the
recommendations of the leisure farm owners also provide follow-up
study direction for future researchers.
Abstract: This paper discusses the performance modeling and availability analysis of Yarn Dyeing System of a Textile Industry. The Textile Industry is a complex and repairable engineering system. Yarn Dyeing System of Textile Industry consists of five subsystems arranged in series configuration. For performance modeling and analysis of availability, a performance evaluating model has been developed with the help of mathematical formulation based on Markov-Birth-Death Process. The differential equations have been developed on the basis of Probabilistic Approach using a Transition Diagram. These equations have further been solved using normalizing condition in order to develop the steady state availability, a performance measure of the system concerned. The system performance has been further analyzed with the help of decision matrices. These matrices provide various availability levels for different combinations of failure and repair rates for various subsystems. The findings of this paper are therefore, considered to be useful for the analysis of availability and determination of the best possible maintenance strategies which can be implemented in future to enhance the system performance.
Abstract: The purpose of this study is to understand how
consumers react to a company's promotional offers with mobile
applications (APP) as premiums. This paper presents the results of an
experimental study where five features of APP were involved: the
cost (free/discounted) for earning APP, the relationship between APP
and the promoted product, the perceived usefulness, the perceived
ease of use, and the perceived playfulness of APP in the context of
light foods purchase. The results support that the above features,
except perceived ease of use, have substantial influences on
consumers' intention to adopt the APP. Among the five features, the
cost for earning APP has the most impact on the adopting intention
of APP. The study also found a positive influence of adopting
intention of APP on the consumer's purchase intention of the
promoted product. Thus, APP-based premiums may enhance the
consumer's purchase intention of a company's promoted products.
Abstract: This paper proposes a novel game theoretical
technique to address the problem of data object replication in largescale
distributed computing systems. The proposed technique draws
inspiration from computational economic theory and employs the
extended Vickrey auction. Specifically, players in a non-cooperative
environment compete for server-side scarce memory space to
replicate data objects so as to minimize the total network object
transfer cost, while maintaining object concurrency. Optimization of
such a cost in turn leads to load balancing, fault-tolerance and
reduced user access time. The method is experimentally evaluated
against four well-known techniques from the literature: branch and
bound, greedy, bin-packing and genetic algorithms. The experimental
results reveal that the proposed approach outperforms the four
techniques in both the execution time and solution quality.
Abstract: The catalytic dehydroxylation of glycerol to propylene
glycol was investigated over Cu-ZnO/Al2O3 prepared by incipient
wetness impregnation (IWI) method with different purity feedstocks -
refined glycerol and technical grade glycerol. The main purpose is to
investigate the effects of feed impurities that cause the catalyst
deactivation. The prepared catalyst were tested for its catalytic
activity and selectivity in a continuous flow fixed bed reactor at 523
K, 500 psig, H2/feed molar ratio of 4 and WHSV of 3 h-1. The results
showed that conversion of refined glycerol and technical grade
glycerol at time on stream 6 hour are 99% and 71% and selectivity to
propylene glycol are 87% and 56% respectively. The ICP-EOS and
TPO results indicated that the cause of catalyst deactivation was the
amount of impurities in the feedstock. The higher amount of
impurities (especially Na and K) the lower catalytic activity.
Abstract: In hydrocyclones, the particle separation efficiency is
limited by the suspended fine particles, which are discharged with the
coarse product in the underflow. It is well known that injecting water
in the conical part of the cyclone reduces the fine particle fraction in
the underflow. This paper presents a mathematical model that
simulates the water injection in the conical component. The model
accounts for the fluid flow and the particle motion. Particle
interaction, due to hindered settling caused by increased density and
viscosity of the suspension, and fine particle entrainment by settling
coarse particles are included in the model. Water injection in the
conical part of the hydrocyclone is performed to reduce fine particle
discharge in the underflow. The model demonstrates the impact of
the injection rate, injection velocity, and injection location on the
shape of the partition curve. The simulations are compared with
experimental data of a 50-mm cyclone.
Abstract: In this work, we solve multipoint boundary value
problems where the boundary value conditions are equations using
the Newton-Broyden Shooting method (NBSM).The proposed
method is tested upon several problems from the literature and the
results are compared with the available exact solution. The
experiments are given to illustrate the efficiency and implementation
of the method.
Abstract: A novel method using bearing-only SLAM to estimate node positions of a localization network is proposed. A group of simple robots are used to estimate the position of each node. Each node has a unique ID, which it can communicate to a robot close by. Initially the node IDs and positions are unknown. A case example using RFID technology in the localization network is introduced.
Abstract: Lack of resources for road infrastructure financing is a
problem that currently affects not only eastern European economies
but also many other countries especially in relation to the impact of
global financial crisis. In this context, we are talking about the socalled
short-investment problem as a result of long-term lack of
investment resources. Based on an analysis of road infrastructure
financing in the Czech Republic this article points out at weaknesses
of current system and proposes a long-term planning methodology
supported by system approach. Within this methodology and using
created system dynamic model the article predicts the development of
short-investment problem in the Country and in reaction on the
downward trend of certain sources the article presents various
scenarios resulting from the change of the structure of financial
sources. In the discussion the article focuses more closely on the
possibility of introduction of tax on vehicles instead of taxes with
declining revenue streams and estimates its approximate price in
relation to reaching various solutions of short-investment in time.
Abstract: As the Textile Industry is the second largest industry
in Egypt and as small and medium-sized enterprises (SMEs) make up
a great portion of this industry therein it is essential to apply the
concept of Cleaner Production for the purpose of reducing pollution.
In order to achieve this goal, a case study concerned with ecofriendly
stone-washing of jeans-garments was investigated. A raw
material-substitution option was adopted whereby the toxic
potassium permanganate and sodium sulfide were replaced by the
environmentally compatible hydrogen peroxide and glucose
respectively where the concentrations of both replaced chemicals
together with the operating time were optimized. In addition, a
process-rationalization option involving four additional processes
was investigated. By means of criteria such as product quality,
effluent analysis, mass and heat balance; and cost analysis with the
aid of a statistical model, a process optimization treatment revealed
that the superior process optima were 50%, 0.15% and 50min for
H2O2 concentration, glucose concentration and time, respectively.
With these values the superior process ought to reduce the annual
cost by about EGP 105 relative to the currently used conventional
method.
Abstract: This paper presents a novel approach for representing
the spatio-temporal topology of the camera network with overlapping
and non-overlapping fields of view (FOVs). The topology is
determined by tracking moving objects and establishing object
correspondence across multiple cameras. To track people successfully
in multiple camera views, we used the Merge-Split (MS) approach for
object occlusion in a single camera and the grid-based approach for
extracting the accurate object feature. In addition, we considered the
appearance of people and the transition time between entry and exit
zones for tracking objects across blind regions of multiple cameras
with non-overlapping FOVs. The main contribution of this paper is to
estimate transition times between various entry and exit zones, and to
graphically represent the camera topology as an undirected weighted
graph using the transition probabilities.
Abstract: One of the main concerns about parallel mechanisms
is the presence of singular points within their workspaces. In singular
positions the mechanism gains or loses one or several degrees of
freedom. It is impossible to control the mechanism in singular
positions. Therefore, these positions have to be avoided. This is a
vital need especially in computer controlled machine tools designed
and manufactured on the basis of parallel mechanisms. This need has
to be taken into consideration when selecting design parameters. A
prerequisite to this is a thorough knowledge about the effect of
design parameters and constraints on singularity. In this paper,
quality condition index was introduced as a criterion for evaluating
singularities of different configurations of a hexapod mechanism
obtainable by different design parameters. It was illustrated that this
method can effectively be employed to obtain the optimum
configuration of hexapod mechanism with the aim of avoiding
singularity within the workspace. This method was then employed to
design the hexapod table of a CNC milling machine.
Abstract: Wireless sensor networks (WSNs) consist of number
of tiny, low cost and low power sensor nodes to monitor some physical phenomenon. The major limitation in these networks is the use of non-rechargeable battery having limited power supply. The
main cause of energy consumption in such networks is
communication subsystem. This paper presents an energy efficient
Cluster Cooperative Caching at Sensor (C3S) based upon grid type clustering. Sensor nodes belonging to the same cluster/grid form a
cooperative cache system for the node since the cost for
communication with them is low both in terms of energy
consumption and message exchanges. The proposed scheme uses
cache admission control and utility based data replacement policy to
ensure that more useful data is retained in the local cache of a node.
Simulation results demonstrate that C3S scheme performs better in
various performance metrics than NICoCa which is existing
cooperative caching protocol for WSNs.
Abstract: This paper applies fuzzy clustering algorithm in classifying real estate companies in China according to some general financial indexes, such as income per share, share accumulation fund, net profit margins, weighted net assets yield and shareholders' equity. By constructing and normalizing initial partition matrix, getting fuzzy similar matrix with Minkowski metric and gaining the transitive closure, the dynamic fuzzy clustering analysis for real estate companies is shown clearly that different clustered result change gradually with the threshold reducing, and then, it-s shown there is the similar relationship with the prices of those companies in stock market. In this way, it-s great valuable in contrasting the real estate companies- financial condition in order to grasp some good chances of investment, and so on.
Abstract: Wireless sensor network is formed with the combination of sensor nodes and sink nodes. Recently Wireless sensor network has attracted attention of the research community. The main application of wireless sensor network is security from different attacks both for mass public and military. However securing these networks, by itself is a critical issue due to many constraints like limited energy, computational power and lower memory. Researchers working in this area have proposed a number of security techniques for this purpose. Still, more work needs to be done.In this paper we provide a detailed discussion on security in wireless sensor networks. This paper will help to identify different obstacles and requirements for security of wireless sensor networks as well as highlight weaknesses of existing techniques.
Abstract: We propose a novel graphical technique (SVision) for
intrusion detection, which pictures the network as a community of
hosts independently roaming in a 3D space defined by the set of
services that they use. The aim of SVision is to graphically cluster
the hosts into normal and abnormal ones, highlighting only the ones
that are considered as a threat to the network. Our experimental
results using DARPA 1999 and 2000 intrusion detection and
evaluation datasets show the proposed technique as a good candidate
for the detection of various threats of the network such as vertical
and horizontal scanning, Denial of Service (DoS), and Distributed
DoS (DDoS) attacks.