Abstract: The research on two-wheeled inverted pendulum (TWIP) mobile robots or commonly known as balancing robots have gained momentum over the last decade in a number of robotic laboratories around the world. This paper describes the hardware design of such a robot. The objective of the design is to develop a TWIP mobile robot as well as MATLAB interfacing configuration to be used as flexible platform comprises of embedded unstable linear plant intended for research and teaching purposes. Issues such as selection of actuators and sensors, signal processing units, MATLAB Real Time Workshop coding, modeling and control scheme will be addressed and discussed. The system is then tested using a wellknown state feedback controller to verify its functionality.
Abstract: The paper discusses a 3D numerical solution of the inverse boundary problem for a continuous casting process of alloy. The main goal of the analysis presented within the paper was to estimate heat fluxes along the external surface of the ingot. The verified information on these fluxes was crucial for a good design of a mould, effective cooling system and generally the whole caster. In the study an enthalpy-porosity technique implemented in Fluent package was used for modeling the solidification process. In this method, the phase change interface was determined on the basis of the liquid fraction approach. In inverse procedure the sensitivity analysis was applied for retrieving boundary conditions. A comparison of the measured and retrieved values showed a high accuracy of the computations. Additionally, the influence of the accuracy of measurements on the estimated heat fluxes was also investigated.
Abstract: The kinetics of palm oil catalytic cracking over
aluminum containing mesoporous silica Al-MCM-41 (5% Al) was
investigated in a batch autoclave reactor at the temperatures range of
573 – 673 K. The catalyst was prepared by using sol-gel technique
and has been characterized by nitrogen adsorption and x-ray
diffraction methods. Surface area of 1276 m2/g with average pore
diameter of 2.54 nm and pore volume of 0.811 cm3/g was obtained.
The experimental catalytic cracking runs were conducted using 50 g
of oil and 1 g of catalyst. The reaction pressure was recorded at
different time intervals and the data were analyzed using Levenberg-
Marquardt (LM) algorithm using polymath software. The results
show that the reaction order was found to be -1.5 and activation
energy of 3200 J/gmol.
Abstract: The forest fires in Thailand are annual occurrence which is the cause of air pollutions. This study intended to estimate the emission from forest fire during 2005-2009 using MODerateresolution Imaging Spectro-radiometer (MODIS) sensor aboard the Terra and Aqua satellites, experimental data, and statistical data. The forest fire emission is estimated using equation established by Seiler and Crutzen in 1982. The spatial and temporal variation of forest fire emission is analyzed and displayed in the form of grid density map. From the satellite data analysis suggested between 2005 and 2009, the number of fire hotspots occurred 86,877 fire hotspots with a significant highest (more than 80% of fire hotspots) in the deciduous forest. The peak period of the forest fire is in January to May. The estimation on the emissions from forest fires during 2005 to 2009 indicated that the amount of CO, CO2, CH4, and N2O was about 3,133,845 tons, 47,610.337 tons, 204,905 tons, and 6,027 tons, respectively, or about 6,171,264 tons of CO2eq. They also emitted 256,132 tons of PM10. The year 2007 was found to be the year when the emissions were the largest. Annually, March is the period that has the maximum amount of forest fire emissions. The areas with high density of forest fire emission were the forests situated in the northern, the western, and the upper northeastern parts of the country.
Abstract: Thermo-chemical treatment (TCT) such as pyrolysis
is getting recognized as a valid route for (i) materials and valuable
products and petrochemicals recovery; (ii) waste recycling; and (iii)
elemental characterization. Pyrolysis is also receiving renewed
attention for its operational, economical and environmental
advantages. In this study, samples of polyethylene terephthalate
(PET) and polystyrene (PS) were pyrolysed in a microthermobalance
reactor (using a thermogravimetric-TGA setup). Both
polymers were prepared and conditioned prior to experimentation.
The main objective was to determine the kinetic parameters of the
depolymerization reactions that occur within the thermal degradation
process. Overall kinetic rate constants (ko) and activation energies
(Eo) were determined using the general kinetics theory (GKT)
method previously used by a number of authors. Fitted correlations
were found and validated using the GKT, errors were within ± 5%.
This study represents a fundamental step to pave the way towards the
development of scaling relationship for the investigation of larger
scale reactors relevant to industry.
Abstract: This paper uses quasi-steady molecular statics model
and diamond tool to carry out simulation temperature rise of nanoscale
orthogonal cutting single-crystal silicon. It further qualitatively
analyzes temperature field of silicon workpiece without considering
heat transfer and considering heat transfer. This paper supposes that
the temperature rise of workpiece is mainly caused by two heat sources:
plastic deformation heat and friction heat. Then, this paper develops a
theoretical model about production of the plastic deformation heat and
friction heat during nanoscale orthogonal cutting. After the increased
temperature produced by these two heat sources are added up, the
acquired total temperature rise at each atom of the workpiece is
substituted in heat transfer finite difference equation to carry out heat
transfer and calculates the temperature field in each step and makes
related analysis.
Abstract: In this work, grinding or microcutting tools in the form of pellets were manufactured using a bounded alumina abrasive grains. The bound used is a vitreous material containing quartz feldspars, kaolinite and a quantity of hematite. The pellets were used in glass grinding process to replace the free abrasive grains lapping process. The study of the elaborated pellets were done to define their effectiveness in the grinding process and to optimize the influence of the pellets elaboration parameters. The obtained results show the existence of an optimal combination of the pellets elaboration parameters for each glass grinding phase (coarse to fine grinding). The final roughness (rms) reached by the elaborated pellets on a BK7 glass surface was about 0.392 μm.
Abstract: Spectrum is a scarce commodity, and considering the spectrum scarcity faced by the wireless-based service providers led to high congestion levels. Technical inefficiencies from pooled, since all networks share a common pool of channels, exhausting the available channels will force networks to block the services. Researchers found that cognitive radio (CR) technology may resolve the spectrum scarcity. A CR is a self-configuring entity in a wireless networking that senses its environment, tracks changes, and frequently exchanges information with their networks. However, CRN facing challenges and condition become worst while tracks changes i.e. reallocation of another under-utilized channels while primary network user arrives. In this paper, channels or resource reallocation technique based on DNA-inspired computing algorithm for CRN has been proposed.
Abstract: An unsupervised classification algorithm is derived
by modeling observed data as a mixture of several mutually
exclusive classes that are each described by linear combinations of
independent non-Gaussian densities. The algorithm estimates the
data density in each class by using parametric nonlinear functions
that fit to the non-Gaussian structure of the data. This improves
classification accuracy compared with standard Gaussian mixture
models. When applied to textures, the algorithm can learn basis
functions for images that capture the statistically significant structure
intrinsic in the images. We apply this technique to the problem of
unsupervised texture classification and segmentation.
Abstract: This paper presents an algorithm to estimate the parameters of two closely spaced sinusoids, providing a frequency resolution that is more than 800 times greater than that obtained by using the Discrete Fourier Transform (DFT). The strategy uses a highly optimized grid search approach to accurately estimate frequency, amplitude and phase of both sinusoids, keeping at the same time the computational effort at reasonable levels. The proposed method has three main characteristics: 1) a high frequency resolution; 2) frequency, amplitude and phase are all estimated at once using one single package; 3) it does not rely on any statistical assumption or constraint. Potential applications to this strategy include the difficult task of resolving coincident partials of instruments in musical signals.
Abstract: The purpose of this research was to study the inspector performance by using computer based training (CBT). Visual inspection task was printed circuit board (PCB) simulated on several types of defects. Subjects were 16 undergraduate randomly selected from King Mongkut-s University of Technology Thonburi and test for 20/20. Then, they were equally divided on performance into two groups (control and treatment groups) and were provided information before running the experiment. Only treatment group was provided feedback information after first experiment. Results revealed that treatment group was showed significantly difference at the level of 0.01. The treatment group showed high percentage on defects detected. Moreover, the attitude of inspectors on using the CBT to inspection was showed on good. These results have been showed that CBT could be used for training to improve inspector performance.
Abstract: In this paper, we present a new method for
incorporating global shift invariance in support vector machines.
Unlike other approaches which incorporate a feature extraction stage,
we first scale the image and then classify it by using the modified
support vector machines classifier. Shift invariance is achieved by
replacing dot products between patterns used by the SVM classifier
with the maximum cross-correlation value between them. Unlike the
normal approach, in which the patterns are treated as vectors, in our
approach the patterns are treated as matrices (or images). Crosscorrelation
is computed by using computationally efficient
techniques such as the fast Fourier transform. The method has been
tested on the ORL face database. The tests indicate that this method
can improve the recognition rate of an SVM classifier.
Abstract: Model-checking tools such as Symbolic Model Verifier
(SMV) and NuSMV are available for checking hardware designs.
These tools can automatically check the formal legitimacy of a
design. However, NuSMV is too low level for describing a complete
hardware design. It is therefore necessary to translate the system
definition, as designed in a language such as Verilog or VHDL, into
a language such as NuSMV for validation. In this paper, we present
a meta hardware description language, Melasy, that contains a code
generator for existing hardware description languages (HDLs) and
languages for model checking that solve this problem.
Abstract: Network-Centric Air Defense Missile Systems
(NCADMS) represents the superior development of the air defense
missile systems and has been regarded as one of the major research
issues in military domain at present. Due to lack of knowledge and
experience on NCADMS, modeling and simulation becomes an effective
approach to perform operational analysis, compared with
those equation based ones. However, the complex dynamic interactions
among entities and flexible architectures of NCADMS put forward
new requirements and challenges to the simulation framework
and models. ABS (Agent-Based Simulations) explicitly addresses
modeling behaviors of heterogeneous individuals. Agents have capability
to sense and understand things, make decisions, and act on the
environment. They can also cooperate with others dynamically to
perform the tasks assigned to them. ABS proves an effective approach
to explore the new operational characteristics emerging in
NCADMS. In this paper, based on the analysis of network-centric
architecture and new cooperative engagement strategies for
NCADMS, an agent-based simulation framework by expanding the
simulation framework in the so-called System Effectiveness Analysis
Simulation (SEAS) was designed. The simulation framework specifies
components, relationships and interactions between them, the
structure and behavior rules of an agent in NCADMS. Based on scenario
simulations, information and decision superiority and operational
advantages in NCADMS were analyzed; meanwhile some
suggestions were provided for its future development.
Abstract: To realize the vision of ubiquitous computing, it is
important to develop a context-aware infrastructure which can help
ubiquitous agents, services, and devices become aware of their
contexts because such computational entities need to adapt themselves
to changing situations. A context-aware infrastructure manages the
context model representing contextual information and provides
appropriate information. In this paper, we introduce Context-Aware
Middleware for URC System (hereafter CAMUS) as a context-aware
infrastructure for a network-based intelligent robot system and discuss
the ontology-based context modeling and reasoning approach which is
used in that infrastructure.
Abstract: The automatic discrimination of seismic signals is an important practical goal for the earth-science observatories due to the large amount of information that they receive continuously. An essential discrimination task is to allocate the incoming signal to a group associated with the kind of physical phenomena producing it. In this paper, we present new techniques for seismic signals classification: local, regional and global discrimination. These techniques were tested on seismic signals from the data base of the National Geophysical Institute of the Centre National pour la Recherche Scientifique et Technique (Morocco) by using the Moroccan software for seismic signals analysis.
Abstract: The real representation of the quaternionic matrix is
definited and studied. The relations between the positive (semi)define
quaternionic matrix and its real representation matrix are presented.
By means of the real representation, the relation between the positive
(semi)definite solutions of quaternionic matrix equations and those of
corresponding real matrix equations is established.
Abstract: A fuzzy classifier using multiple ellipsoids approximating decision regions for classification is to be designed in this paper. An algorithm called Gustafson-Kessel algorithm (GKA) with an adaptive distance norm based on covariance matrices of prototype data points is adopted to learn the ellipsoids. GKA is able toadapt the distance norm to the underlying distribution of the prototypedata points except that the sizes of ellipsoids need to be determined a priori. To overcome GKA's inability to determine appropriate size ofellipsoid, the genetic algorithm (GA) is applied to learn the size ofellipsoid. With GA combined with GKA, it will be shown in this paper that the proposed method outperforms the benchmark algorithms as well as algorithms in the field.
Abstract: The elimination of ranitidine (a pharmaceutical
compound) has been carried out in the presence of UV-C radiation.
After some preliminary experiments, it has been experienced the no
influence of the gas nature (air or oxygen) bubbled in photolytic
experiments. From simple photolysis experiments the quantum yield
of this compound has been determined. Two photolytic
approximation has been used, the linear source emission in parallel
planes and the point source emission in spherical planes. The
quantum yield obtained was in the proximity of 0.05 mol Einstein-1
regardless of the method used. Addition of free radical promoters
(hydrogen peroxide) increases the ranitidine removal rate while the
use of photocatalysts (TiO2) negatively affects the process.
Abstract: In this study, the precision heading process of
spur gears has been investigated by means of numerical
analysis. The effect of some parameters such as teeth number
and module on the forming force and material flow were
presented. The simulation works were performed rigid-plastic
finite element method using DEFORM 3D software. In order
to validate the estimated numerical results, they were
compared with those obtained experimentally during heading
of spur gear using lead as a model material. Results showed
that the optimum number of gear teeth is between 10 to 20,
that is because of being the specific pressure in its minimum
value.