Abstract: This is an application research presenting the
improvement of production quality using the six sigma solutions and
the analyses of benefit-cost ratio. The case of interest is the
production of tile-concrete. Such production has faced with the
problem of high nonconforming products from an inappropriate
surface coating and had low process capability based on the strength
property of tile. Surface coating and tile strength are the most critical
to quality of this product. The improvements followed five stages of
six sigma solutions. After the improvement, the production yield was
improved to 80% as target required and the defective products from
coating process was remarkably reduced from 29.40% to 4.09%. The
process capability based on the strength quality was increased from
0.87 to 1.08 as customer oriented. The improvement was able to save
the materials loss for 3.24 millions baht or 0.11 million dollars. The
benefits from the improvement were analyzed from (1) the reduction
of the numbers of non conforming tile using its factory price for
surface coating improvement and (2) the materials saved from the
increment of process capability. The benefit-cost ratio of overall
improvement was high as 7.03. It was non valuable investment in
define, measure, analyses and the initial of improve stages after that
it kept increasing. This was due to there were no benefits in define,
measure, and analyze stages of six sigma since these three stages
mainly determine the cause of problem and its effects rather than
improve the process. The benefit-cost ratio starts existing in the
improve stage and go on. Within each stage, the individual benefitcost
ratio was much higher than the accumulative one as there was an
accumulation of cost since the first stage of six sigma. The
consideration of the benefit-cost ratio during the improvement
project helps make decisions for cost saving of similar activities
during the improvement and for new project. In conclusion, the
determination of benefit-cost ratio behavior through out six sigma
implementation period provides the useful data for managing quality
improvement for the optimal effectiveness. This is the additional
outcome from the regular proceeding of six sigma.
Abstract: The aluminum bronze matrix alumina composites using hot press and resin infiltration were investigated to study their porosities, hardness, bending strengths, and microstructures. The experiment results show that the hardness of the sintered composites with the decrease of porosity increases. The composites without and with resin infiltration have about HRF 42-61 of about 34-40% of porosity and about HRF 62-83 of about 30-36% of porosity, respectively. Besides, the alumina composites contain a more amount of iron and nickel powders would cause a lower bending strength due to forming some weaker bonding among the iron, nickel, copper, aluminum under this hot pressing of shorter time.
Abstract: Through the time, the higher education has changed
the learning system since mother tongue to bilingual, and in this new
century has been coming develop a multilingual education. All as
part of globalization process of the countries and the education.
Nevertheless, this change only has been effectively in countries of the
first world, the rest have been lagging. Therefore, these countries
require strengthen their higher education systems through models that
give way to multilingual and bilingual education. In this way, shows
a new model adapted from a systemic form to allow a higher
bilingual and multilingual education in Latin America. This
systematization aims to increase the skills and competencies
student’s, decrease the time learning of a second tongue, add to
multilingualism in the American Latin Universities, also, contribute
to position the region´s countries in a better global status, and
stimulate the development of new research in this area.
Abstract: The effects of chitosan, a biodegradable polymer,
were studied in Grammatophyllum speciosum protocorm-like bodies
(PLBs) in vitro culture. The chitosan concentration of 0, 5, 10, 15,
20, 25, 50 or 100 mg/l were supplemented in half-strength Murashige
and Skoog (1/2 MS) liquid or on agar media containing 2% (w/v)
sucrose. The results showed that liquid medium supplemented with
15 mg/l chitosan showed the highest relative growth rate (7-fold
increase) of PLBs. On 1/2 MS agar medium supplemented with 25
mg/l chitosan gave the highest relative growth rate (4-fold increase).
The relative growth rate of G. speciosum PLBs on agar medium was
significantly lower than that in liquid medium. Moreover, chitosan,
supplemented to agar medium promoted shoot formation but not
rooting. However, supplementation at too high a level, such as 100
mg/l can inhibit growth and kill PLBs.
Abstract: In this work, we present for the first time in our perception an efficient digital watermarking scheme for mpeg audio layer 3 files that operates directly in the compressed data domain, while manipulating the time and subband/channel domain. In addition, it does not need the original signal to detect the watermark. Our scheme was implemented taking special care for the efficient usage of the two limited resources of computer systems: time and space. It offers to the industrial user the capability of watermark embedding and detection in time immediately comparable to the real music time of the original audio file that depends on the mpeg compression, while the end user/audience does not face any artifacts or delays hearing the watermarked audio file. Furthermore, it overcomes the disadvantage of algorithms operating in the PCMData domain to be vulnerable to compression/recompression attacks, as it places the watermark in the scale factors domain and not in the digitized sound audio data. The strength of our scheme, that allows it to be used with success in both authentication and copyright protection, relies on the fact that it gives to the users the enhanced capability their ownership of the audio file not to be accomplished simply by detecting the bit pattern that comprises the watermark itself, but by showing that the legal owner knows a hard to compute property of the watermark.
Abstract: The number of electronic participation (eParticipation) projects introduced by different governments and international organisations is considerably high and increasing. In order to have an overview of the development of these projects, various evaluation frameworks have been proposed. In this paper, a five-level participation model, which takes into account the advantages of the Social Web or Web 2.0, together with a quantitative approach for the evaluation of eParticipation projects is presented. Each participation level is evaluated independently, taking into account three main components: Web evolution, media richness, and communication channels. This paper presents the evaluation of a number of existing Voting Advice Applications (VAAs). The results provide an overview of the main features implemented by each project, their strengths and weaknesses, and the participation levels reached.
Abstract: This study examines the influence of information
transparency and corporate governance on purchase directors and
officers liability (D&O) insurance decisions. The results show that
companies with greater information transparency have significant
demand for D&O insurance. Greater transparency in voluntary
disclosures is significantly and positively associated with demand for
insurance, indicating that increasing the degree of information
disclosure reduces information asymmetry for insurers, which
stimulates their willingness to provide greater protection.
Analysis of insured and uninsured subsamples indicates that
uninsured companies have superior corporate governance compared to
insured companies. Although insured companies tend to have weaker
corporate governance structures, they appoint Big 4 firms or industry
experts to compensate for the weakness of their corporate governance.
Empirical results indicate that purchasing D&O insurance can
strengthen external corporate governance and increase companies’
willingness to voluntarily provide more transparent information.
Abstract: Our research aims at helping the tutor on line to
evaluate the student-s cognitive processes. The student is a learner in
French as a Second Language who studies an on-line socio-cognitive
scenario in written communication. In our method, these cognitive
processes are defined. For that, the language abilities and learning
tasks are associated to cognitive operation. Moreover, the found
cognitive processes are named with specific terms. The result was to
create an instrumental pattern to question the learner about the
cognitive processes used to build an item of written comprehension.
Our research follows the principles of the third historical generation
of studies on the cognitive activity of the text comprehension. The
strength of our instrumental pattern stands in the precision and the
logical articulation of the questions to the learner. However, the
learner-s answers can still be subjective but the precision of the
instrument restricts it.
Abstract: Lake Nasser is one of the largest reservoirs in the
world. Over 120 million metric tons of sediments are deposited in its
dead storage zone every year. The main objective of the present work
was to determine the physical and chemical characteristics of Lake
Nasser sediments. The sample had a relatively low surface area of 2.9
m2/g which increased more than 3-fold upon chemical activation. The
main chemical elements of the raw sediments were C, O and Si with
some traces of Al, Fe and Ca. The organic functional groups for the
tested sample included O-H, C=C, C-H and C-O, with indications of
Si-O and other metal-C and/or metal-O bonds normally associated
with clayey materials. Potentiometric titration of the sample in
different ionic strength backgrounds revealed an alkaline material with
very strong positive surface charge at pH values just a little less than
the pH of zero charge which is ~9. Surface interactions of the
sediments with the background electrolyte were significant. An
advanced surface complexation model was able to capture these
effects, employing a single-site approach to represent protolysis
reactions in aqueous solution, and to determine the significant surface
species in the pH range of environmental interest.
Abstract: A new numerical method for solving the twodimensional,
steady, incompressible, viscous flow equations on a
Curvilinear staggered grid is presented in this paper. The proposed
methodology is finite difference based, but essentially takes
advantage of the best features of two well-established numerical
formulations, the finite difference and finite volume methods. Some
weaknesses of the finite difference approach are removed by
exploiting the strengths of the finite volume method. In particular,
the issue of velocity-pressure coupling is dealt with in the proposed
finite difference formulation by developing a pressure correction
equation in a manner similar to the SIMPLE approach commonly
used in finite volume formulations. However, since this is purely a
finite difference formulation, numerical approximation of fluxes is
not required. Results obtained from the present method are based on
the first-order upwind scheme for the convective terms, but the
methodology can easily be modified to accommodate higher order
differencing schemes.
Abstract: The present study aimed to investigate whether
chlorophyll meter readings (SPAD) can be used as criterion of singleplant
selection in maize breeding. Experimentation was performed at
the ultra-low density of 0.74 plants/m2 in order the potential yield per
plant to be fully expressed. R-31 honeycomb experiments were
conducted in three different areas in Greece (Thessaloniki, Giannitsa
and Florina) using 30 inbred lines at well-watered and water-stressed
conditions during the 2012 growing season. The chlorophyll meter
readings had higher rates at dry conditions, except location of
Giannitsa where differences were not significant. Genotypes of
highest chlorophyll meter readings were consistent across areas,
emphasizing on the character’s stability. A positive correlation
between the chlorophyll meter readings and grain yield was
strengthening over time and culminated at the physiological maturity
stage. There was a clear sign that the chlorophyll meter readings has
the potential to be used for the selection of stress-adaptive genotypes
and may permit modern maize to be grown at wider range of
environments addressing the climate change scenarios.
Abstract: Mechanical buckling analysis of rectangular plates
with central circular cutout is performed in this paper. The finiteelement
method is used to study the effects of plate-support
conditions, aspect ratio, and hole size on the mechanical buckling
strength of the perforated plates subjected to linearly varying loading.
Results show that increasing the hole size does not necessarily reduce
the mechanical buckling strength of the perforated plates. It is also
concluded that the clamped boundary condition increases the
mechanical buckling strength of the perforated plates more than the
simply-supported boundary condition and the free boundary
conditions enhance the mechanical buckling strength of the
perforated plates more effectively than the fixed boundary conditions.
Furthermore, for the bending cases, the critical buckling load of
perforated plates with free edges is less than perforated plates with
fixed edges.
Abstract: The mechanical properties of blends consisting of
plasticized poly(vinyl butyral) (PVB) and plasticized poly(vinyl
chloride) (PVC) are studied, in order to evaluate the possibility of
using recycled PVB waste derived from windshields. PVC was
plasticized with 38% of diisononyl phthalate (DINP), while PVB was
plasticized with 28% of triethylene glycol, bis(2-ethylhexanoate)
(3GO). The optimal process conditions for the PVB/PVC blend in 1:1
ratio were determined. Entropy was used in order to theoretically
predict the blends miscibility. The PVB content of each blend
composition used was ranging from zero to 100%. Tensile strength
and strain were tested. In addition, a comparison between recycled
and original PVB, used as constituents of the blend, was performed.
Abstract: The purpose of this paper is to investigate the
durability of cement mortar in presence of Rice Husk Ash (RHA).
The strength and durability of mortar with different replacement
level (0%, 10%, 15%, 20%, 25% and 30%) of Ordinary Portland
Cement (OPC) by RHA is investigated here. RHA was
manufactured from an uncontrolled burning process. Test samples
were prepared with river sand of FM 2.73. Samples were kept in
controlled environment up to test time. The results show that
addition of RHA was shown better results for 20% replacement
level than OPC at 90 days. In durability test all samples passed for
20 cycles except 25% and 30% replacement level.
Abstract: The market transformation in Kazakhstan during the
last two decades has essentially strengthened a gap between
development of urban and rural areas. Implementation of market
institutes, transition from public financing to paid rendering of social
services, change of forms of financing of social and economic
infrastructure have led to strengthening of an economic inequality of
social groups, including growth of stratification of the city and the
village. Sociological survey of urban and rural households in Almaty
city and villages of Almaty region has been carried out within the
international research project “Livelihoods Strategies of Private
Households in Central Asia: A Rural–Urban Comparison in
Kazakhstan and Kyrgyzstan" (Germany, Kazakhstan, Kyrgyzstan).
The analysis of statistical data and results of sociological research of
urban and rural households allows us to reveal issues of territorial
development, to investigate an availability of medical, educational
and other services in the city and the village, to reveal an evaluation
urban and rural dwellers of living conditions, to compare economic
strategies of households in the city and the village.
Abstract: These days we face with so many advertisements in
magazines, those mentioned coaching is pragmatic specialties which
help people make change in their lives. Up to know Specialty coaches
are not necessarily therapists, consultants or psychologist, thus they
may not know psychological theories. The International Coach
Federation identifies "facilitating learning and results" as one of its
four core coach competencies, without understanding learning
theories coaching practice hangs in theoretical abyss. Thus the aim of
this article is investigating learning theories within coaching process.
Therefore, I reviewed some cognitive and behavioral learning
theories and analyzed their contribution with coaching process which
has been introduced in mentor coaches and ICF certified coaches'
papers and books. The result demonstrated that coaching profession
is strongly grounded in learning theories, and it will be strengthened
by the validation of theories and evidence-based research as we move
forward. Thus, it needs more research in order to applying effective
theoretical frameworks.
Abstract: WLAN Positioning has been presented by many
approaches in literatures using the characteristics of Received Signal
Strength (RSS), Time of Arrival (TOA) or Time Difference of
Arrival (TDOA), Angle of Arrival (AOA) and cell ID. Among these,
RSS approach is the simplest method to implement because there is
no need of modification on both access points and client devices
whereas its accuracy is terrible due to physical environments. For
TOA or TDOA approach, the accuracy is quite acceptable but most
researches have to modify either software or hardware on existing
WLAN infrastructure. The scales of modifications are made on only
access card up to the changes in protocol of WLAN. Hence, it is an
unattractive approach to use TOA or TDOA for positioning system.
In this paper, the new concept of merging both RSS and TOA
positioning techniques is proposed. In addition, the method to
achieve TOA characteristic for positioning WLAN user without any
extra modification necessarily appended in the existing system is
presented. The measurement results confirm that the proposed
technique using both RSS and TOA characteristics provides better
accuracy than using only either RSS or TOA approach.
Abstract: Polylactic acid-g-polyvinyl acetate (PLLA-g-PVAc)
was used as a compatibilizer for 50/50 starch/PLLA blend. PLLA-g-
PVAc with different mol% of PVAc contents were prepared by
grafting PVAc onto PLLA backbone via free radical polymerization
in solution process. Various conditions such as type and the amount
of initiator, monomer concentration, polymerization time and
temperature were studied. Results showed that the highest mol% of
PVAc grafting (16 mol%) was achieved by conducting graft
copolymerization in toluene at 110°C for 10 h using DCP as an
initiator. Chemical structure of the PVAc grafted PLLA was
confirmed by 1H NMR. Blending of modified starch and PLLA in the
presence compatibilizer with different amounts and mol% PVAc was
acquired using internal mixer at 160°C for 15 min. Effects of PVAc
content and the amount of compatibilizer on mechanical properties of
polymer blend were studied. Results revealed that tensile strength and
tensile modulus of polymer blend with higher PVAc grafting content
compatibilizer showed better properties than that of lower PVAc
grafting content compatibilizer. The amount of compatibilizer was
found optimized in the range of 0.5-1.0 Wt% depending on the mol%
PVAc.
Abstract: This paper proposes, implements and evaluates an original discretization method for continuous random variables, in order to estimate the reliability of systems for which stress and strength are defined as complex functions, and whose reliability is not derivable through analytic techniques. This method is compared to other two discretizing approaches appeared in literature, also through a comparative study involving four engineering applications. The results show that the proposal is very efficient in terms of closeness of the estimates to the true (simulated) reliability. In the study we analyzed both a normal and a non-normal distribution for the random variables: this method is theoretically suitable for each parametric family.
Abstract: To date, theoretical studies concerning the Carbon
Fiber Reinforced Polymer (CFRP) strengthening of RC beams with
openings have been rather limited. In addition, various numerical
analyses presented so far have effectively simulated the behaviour of
solid beam strengthened by FRP material. In this paper, a two
dimensional nonlinear finite element analysis is presented to validate
against the laboratory test results of six RC beams. All beams had the
same rectangular cross-section geometry and were loaded under four
point bending. The crack pattern results of the finite element model
show good agreement with the crack pattern of the experimental
beams. The load midspan deflection curves of the finite element
models exhibited a stiffer result compared to the experimental beams.
The possible reason may be due to the perfect bond assumption used
between the concrete and steel reinforcement.