Abstract: Breast Cancer is one of the most considerable diseases in the United States and other countries and is the second leading cause of death in women. Common breast cancer treatments would lead to adverse side effects such as loss of hair, nausea, and weakness. These complications arise because these cancer treatments damage some healthy cells while eliminating the cancer cells. In an effort to address these complications, laser radiation was utilized and tested as a targeted cancer treatment for breast cancer. In this regard, tissue engineering approaches are being employed by using an electrospun scaffold in order to facilitate the growth of breast cancer cells. Polycaprolacton (PCL) was used as a material for scaffold fabricating because of its biocompatibility, biodegradability, and supporting cell growth. The specific breast cancer cells have the ability to create a three-dimensional cell cluster due to the spontaneous accumulation of cells in the porosity of the scaffold under some specific conditions. Therefore, we are looking for a higher density of porosity and larger pore size. Fibers showed uniform diameter distribution and final scaffold had optimum characteristics with approximately 40% porosity. The images were taken by SEM and the density and the size of the porosity were determined with the Image. After scaffold preparation, it has cross-linked by glutaraldehyde. Then, it has been washed with glycine and phosphate buffer saline (PBS), in order to neutralize the residual glutaraldehyde. 3-(4,5-Dimethylthiazol-2-yl)-2,5-diphenyltetrazolium bromidefor (MTT) results have represented approximately 91.13% viability of the scaffolds for cancer cells. In order to create a cluster, Michigan Cancer Foundation-7 (MCF-7, breast cancer cell line) and Michigan Cancer Foundation-10A (MCF-10A, human mammary epithelial cell line) cells were cultured on the scaffold in 24 well plate for five days. Then, we have exposed the cluster to the laser diode 808 nm radiation to investigate the effect of laser on the tumor with different power and time. Under the same conditions, cancer cells lost their viability more than the healthy ones. In conclusion, laser therapy is a viable method to destroy the target cells and has a minimum effect on the healthy tissues and cells and it can improve the other method of cancer treatments limitations.
Abstract: Biological and chemical activities in carbonates are responsible for the complexity of the pore system. Primary porosity is generally of natural origin while secondary porosity is subject to chemical reactivity through diagenetic processes. To understand the integrated part of hydrocarbon exploration, it is necessary to understand the carbonate pore system. However, the current porosity classification scheme is limited to adequately predict the petrophysical properties of different reservoirs having various origins and depositional environments. Rock classification provides a descriptive method for explaining the lithofacies but makes no significant contribution to the application of porosity and permeability (poro-perm) correlation. The Central Luconia carbonate system (Malaysia) represents a good example of pore complexity (in terms of nature and origin) mainly related to diagenetic processes which have altered the original reservoir. For quantitative analysis, 32 high-resolution images of each thin section were taken using transmitted light microscopy. The quantification of grains, matrix, cement, and macroporosity (pore types) was achieved using a petrographic analysis of thin sections and FESEM images. The point counting technique was used to estimate the amount of macroporosity from thin section, which was then subtracted from the total porosity to derive the microporosity. The quantitative observation of thin sections revealed that the mouldic porosity (macroporosity) is the dominant porosity type present, whereas the microporosity seems to correspond to a sum of 40 to 50% of the total porosity. It has been proven that these Miocene carbonates contain a significant amount of microporosity, which significantly complicates the estimation and production of hydrocarbons. Neglecting its impact can increase uncertainty about estimating hydrocarbon reserves. Due to the diversity of geological parameters, the application of existing porosity classifications does not allow a better understanding of the poro-perm relationship. However, the classification can be improved by including the pore types and pore structures where they can be divided into macro- and microporosity. Such studies of microporosity identification/classification represent now a major concern in limestone reservoirs around the world.
Abstract: In this study, Bombyx mori silk fibroin/gelatin (SF/GT) nanocomposite with different GT ratio (SF/GT 100/0, 90/10 and 70/30) were prepared by electrospinning process and crosslinked with glutaraldehyde (GA) vapor. Properties of crosslinked SF/GT nanocomposites were investigated by scanning electron microscopy (SEM), mechanical test, water uptake capacity (WUC) and porosity. From SEM images, it was found that fiber diameter increased as GT content increased. The results of mechanical test indicated that the SF/GT 70/30 nanocomposites had both the highest Young’s modulus of 342 MPa and the highest tensile strength of about 14 MPa. However, porosity and WUC decreased from 62% and 405% for pristine SF to 47% and 232% for SF/GT 70/30, respectively. This behavior can be related to higher degree of crosslinking as GT ratio increased which altered the structure and physical properties of scaffolds. This study showed that incorporation of GT into SF nanofibers can enhance mechanical properties of resultant nanocomposite, but the GA treatment should be optimized to control and fine-tune other properties to warrant their biomedical application.
Abstract: Poor ability of cartilage tissue when experiencing a damage leads scientists to use tissue engineering as a reliable and effective method for regenerating or replacing damaged tissues. An artificial tissue should have some features such as biocompatibility, biodegradation and, enough mechanical properties like the original tissue. In this work, a composite hydrogel is prepared by using natural and synthetic materials that has high porosity. Mechanical properties of different combinations of polymers such as modulus of elasticity were tested, and a hydrogel with good mechanical properties was selected. Bone marrow derived mesenchymal stem cells were also seeded into the pores of the sponge, and the results showed the adhesion and proliferation of cells within the hydrogel after one month. In comparison with previous works, this study offers a new and efficient procedure for the fabrication of cartilage like tissue and further cartilage repair.
Abstract: Forging, milling, turning, grinding and shaping etc. are the various industrial manufacturing processes which generate the metal waste. Grinding is extensively used in the finishing operation. The waste generated contains significant impurities apart from the metal particles. Due to these significant impurities, it becomes difficult to process and gets usually dumped in the landfills which create environmental problems. Therefore, it becomes essential to reuse metal waste to create value added products. Powder injection molding process is used for producing the porous metal matrix framework. This paper discusses the presented design of the porous framework to be used for the liquid filter application. Different parameters are optimized to obtain the better strength framework with variable porosity. Carbon nanotubes are used as reinforcing materials to enhance the strength of the metal matrix framework.
Abstract: Particle reinforced Metal Matrix Composite (MMC) succeeds in synergizing the metallic matrix with ceramic particle reinforcements to result in improved strength, particularly at elevated temperatures, but adversely it affects the ductility of the matrix because of agglomeration and porosity. The present study investigates the outcome of tensile properties in a cast and hot forged composite reinforced simultaneously with coarse and fine particles. Nano-sized alumina particles have been generated by milling mixture of aluminum and manganese dioxide powders. Milled particles after drying are added to molten metal and the resulting slurry is cast. The microstructure of the composites shows good distribution of both the size categories of particles without significant clustering. The presence of nanoparticles along with coarser particles in a composite improves both strength and ductility considerably. Delay in debonding of coarser particles to higher stress is due to reduced mismatch in extension caused by increased strain hardening in presence of the nanoparticles. However, higher addition of powder mix beyond a limit results in deterioration of mechanical properties, possibly due to clustering of nanoparticles. The porosity in cast composite generally increases with the increasing addition of powder mix as observed during process and on forging it has got reduced. The base alloy and nanocomposites show improvement in flow stress which could be attributed to lowering of porosity and grain refinement as a consequence of forging.
Abstract: Rapid Prototyping (RP) technologies enable physical
parts to be produced from various materials without depending on the
conventional tooling. Fused Deposition Modeling (FDM) is one of
the famous RP processes used at present. Tensile strength and
compressive strength resistance will be identified for different sample
structures and different layer orientations of ABS rapid prototype
solid models. The samples will be fabricated by a FDM rapid
prototyping machine in different layer orientations with variations in
internal geometrical structure. The 0° orientation where layers were
deposited along the length of the samples displayed superior strength
and impact resistance over all the other orientations. The anisotropic
properties were probably caused by weak interlayer bonding and
interlayer porosity.
Abstract: In this study, several crossplots of the P-impedance
with the lithology logs (gamma ray, neutron porosity, deep resistivity,
water saturation and Vp/Vs curves) were made in three available
wells, which were drilled in central part of the Blue Nile basin in
depths varies from 1460m to 1600m. These crossplots were
successful to discriminate between sand and shale when using PImpedance
values, and between the wet sand and the pay sand when
using both P-impedance and Vp/Vs together. Also some impedance
sections were converted to porosity sections using linear formula to
characterize the reservoir in terms of porosity. The used crossplots
were created on log resolution, while the seismic resolution can
identify only the reservoir, unless a 3D seismic angle stacks were
available; then it would be easier to identify the pay sand with great
confidence; through high resolution seismic inversion and
geostatistical approach when using P-impedance and Vp/Vs volumes.
Abstract: The purpose of this paper is to examine gas transport
behavior of mixed matrix membranes (MMMs) combined with
porous particles. Main existing models are categorized in two main
groups; two-phase (ideal contact) and three-phase (non-ideal contact).
A new coefficient, J, was obtained to express equations for estimating
effect of the particle porosity in two-phase and three-phase models.
Modified models evaluates with existing models and experimental
data using Matlab software. Comparison of gas permeability of
proposed modified models with existing models in different MMMs
shows a better prediction of gas permeability in MMMs.
Abstract: Three dimensional non-Interlaced carbon fibre
reinforced silicon carbide (3-D-Cf/SiC) composites with pyrocarbon
interphase were fabricated using isothermal chemical vapor
infiltration (ICVI) combined with polymer impregnation pyrolysis
(PIP) process. Polysilazane (PSZ) is used as a preceramic polymer to
obtain silicon carbide matrix. Thermo gravimetric analysis (TGA),
Infrared spectroscopic analysis (IR) and X-ray diffraction (XRD)
analysis were carried out on PSZ pyrolysed at different temperatures
to understand the pyrolysis and obtaining the optimum pyrolysing
condition to yield β-SiC phase. The density of the composites was
1.94 g cm-3 after the 3-D carbon preform was SiC infiltrated for 280 h
with one intermediate polysilazane pre-ceramic PIP process.
Mechanical properties of the composite materials were investigated
under tensile, flexural, shear and impact loading. The values of
tensile strength were 200 MPa at room temperature (RT) and 195
MPa at 500°C in air. The average RT flexural strength was 243 MPa.
The lower flexural strength of these composites is because of the
porosity. The fracture toughness obtained from single edge notched
beam (SENB) technique was 39 MPa.m1/2. The work of fracture
obtained from the load-displacement curve of SENB test was 22.8
kJ.m-2. The composites exhibited excellent impact resistance and the
dynamic fracture toughness of 44.8 kJ.m-2 is achieved as determined
from instrumented Charpy impact test. The shear strength of the
composite was 93 MPa, which is significantly higher compared 2-D
Cf/SiC composites. Microstructure evaluation of fracture surfaces
revealed the signatures of fracture processes and showed good
support for the higher toughness obtained.
Abstract: Saturated hydraulic conductivity is one of the soil
hydraulic properties which is widely used in environmental studies
especially subsurface ground water. Since, its direct measurement is
time consuming and therefore costly, indirect methods such as
pedotransfer functions have been developed based on multiple linear
regression equations and neural networks model in order to estimate
saturated hydraulic conductivity from readily available soil
properties e.g. sand, silt, and clay contents, bulk density, and organic
matter. The objective of this study was to develop neural networks
(NNs) model to estimate saturated hydraulic conductivity from
available parameters such as sand and clay contents, bulk density,
van Genuchten retention model parameters (i.e. r
θ , α , and n) as well
as effective porosity. We used two methods to calculate effective
porosity: : (1) eff s FC φ =θ -θ , and (2) inf φ =θ -θ eff s , in which s
θ is
saturated water content, FC θ is water content retained at -33 kPa
matric potential, and inf θ is water content at the inflection point.
Total of 311 soil samples from the UNSODA database was divided
into three groups as 187 for the training, 62 for the validation (to
avoid over training), and 62 for the test of NNs model. A commercial
neural network toolbox of MATLAB software with a multi-layer
perceptron model and back propagation algorithm were used for the
training procedure. The statistical parameters such as correlation
coefficient (R2), and mean square error (MSE) were also used to
evaluate the developed NNs model. The best number of neurons in
the middle layer of NNs model for methods (1) and (2) were
calculated 44 and 6, respectively. The R2 and MSE values of the test
phase were determined for method (1), 0.94 and 0.0016, and for
method (2), 0.98 and 0.00065, respectively, which shows that method
(2) estimates saturated hydraulic conductivity better than method (1).
Abstract: In the present investigation, H13 tool steel has been
deposited on copper alloy substrate using both CO2 and diode laser.
A detailed parametric analysis has been carried out in order to find
out optimum processing zone for coating defect free H13 tool steel
on copper alloy substrate. Followed by parametric optimization, the
microstructure and microhardness of the deposited clads have been
evaluated. SEM micrographs revealed dendritic microstructure in
both clads. However, the microhardness of CO2 laser deposited clad
was much higher compared to diode laser deposited clad.
Abstract: The aluminum bronze matrix alumina composites using hot press and resin infiltration were investigated to study their porosities, hardness, bending strengths, and microstructures. The experiment results show that the hardness of the sintered composites with the decrease of porosity increases. The composites without and with resin infiltration have about HRF 42-61 of about 34-40% of porosity and about HRF 62-83 of about 30-36% of porosity, respectively. Besides, the alumina composites contain a more amount of iron and nickel powders would cause a lower bending strength due to forming some weaker bonding among the iron, nickel, copper, aluminum under this hot pressing of shorter time.
Abstract: Significant changes in oil and gas drilling have
emphasized the need to verify the integrity and reliability of drill
stem components. Defects are inevitable in cast components,
regardless of application; but if these defects go undetected, any
severe defect could cause down-hole failure.
One such defect is shrinkage porosity. Castings with lower level
shrinkage porosity (CB levels 1 and 2) have scattered pores and do
not occupy large volumes; so pressure testing and helium leak testing
(HLT) are sufficient for qualifying the castings. However, castings
with shrinkage porosity of CB level 3 and higher, behave erratically
under pressure testing and HLT making these techniques insufficient
for evaluating the castings- integrity.
This paper presents a case study to highlight how the radiography
technique is much more effective than pressure testing and HLT.
Abstract: In this paper the combination of thermal oxidation and
electrochemical anodizing processes is used to produce titanium
oxide layers. The response of titanium alloy Ti6Al4V to oxidation
processes at various temperatures and electrochemical anodizing in
various voltages are investigated. Scanning electron microscopy
(SEM); X-Ray Diffraction (XRD) and porosity determination have
been used to characterize the oxide layer thickness, surface
morphology, oxide layer-substrate adhesion and porosity. In the first
experiment, samples modified by thermal oxidation process then
followed by electrochemical anodizing. Second experiment consists
of surfaces modified by electrochemical anodizing process and then
followed by thermal oxidation. The first method shows better
properties than other one. In second experiment, Surfaces modified
were achieved by thicker and more adherent thick oxide layers on
titanium surface. The existence of an electrochemical anodized oxide
layer did not improve the adhesion of thermal oxide layer. The high
temperature, thermal formation of an oxide layer leads to a coarse
oxide grain morphology and a complete oxidative particle. In
addition, in high temperature oxidation porosity content is increased.
The oxide layer of thermal oxidation and electrochemical anodizing
processes; on Ti–6Al–4V substrate was covered with different
colored oxide layers.
Abstract: Microtomographic images and thin section (TS)
images were analyzed and compared against some parameters of
geological interest such as porosity and its distribution along the
samples. The results show that microtomography ( CT) analysis,
although limited by its resolution, have some interesting information
about the distribution of porosity (homogeneous or not) and can also
quantify the connected and non-connected pores, i.e., total porosity.
TS have no limitations concerning resolution, but are limited by the
experimental data available in regards to a few glass sheets for
analysis and also can give only information about the connected
pores, i.e., effective porosity. Those two methods have their own
virtues and flaws but when paired together they are able to
complement one another, making for a more reliable and complete
analysis.
Abstract: This paper proposes the numerical simulation of the
investment casting of gold jewelry. It aims to study the behavior of
fluid flow during mould filling and solidification and to optimize the
process parameters, which lead to predict and control casting defects
such as gas porosity and shrinkage porosity. A finite difference
method, computer simulation software FLOW-3D was used to
simulate the jewelry casting process. The simplified model was
designed for both numerical simulation and real casting production.
A set of sensor acquisitions were allocated on the different positions
of the wax tree of the model to detect filling times, while a set of
thermocouples were allocated to detect the temperature during
casting and cooling. Those detected data were applied to validate the
results of the numerical simulation to the results of the real casting.
The resulting comparisons signify that the numerical simulation can
be used as an effective tool in investment-casting-process
optimization and casting-defect prediction.