Abstract: An experiment was conducted under controlled
conditions to study the effect of water extract of leaves, shoots and
roots of either Sisymbrium irio L. =SISIR and or Descurainia
sophia (L.) Schur =DESSO on the germination and primary growth
of barley. A split-split plot experiment in CRD with three
replications was used. The main plots were the type of weed: i.e.
SISIR and DESSO and the sub-plots were type of organ: i.e. leaf,
stem and root and, the sub-sub plots were concentration of the
water extract of each organ of the weeds: i.e. 0, 2, 4 and 8 % w/v.
The results showed that the SISIR water extracts had a greater
inhibitory effects on the germination and primary growth of barley
than those of DESSO water extracts. The water extracts of the
leaves of both weeds had the greatest inhibitory effects on the
germination and primary growth of barley, compared to those of
stems and roots. Increasing the concentration of water extracts of
leaves, stems and roots of both weeds up to 8 % caused the greatest
inhibitory effects to barley and reduced the germination rate and
primary growth of it linearly.
Abstract: Moral decisions are considered as an intuitive process,
while conscious reasoning is mostly used only to justify those
intuitions. This problem is described in few different dual-process
theories of mind, that are being developed e.g. by Frederick and
Kahneman, Stanovich and Evans. Those theories recently evolved
into tri-process theories with a proposed process that makes ultimate
decision or allows to paraformal processing with focal bias..
Presented experiment compares the decision patterns to the
implications of those models.
In presented study participants (n=179) considered different
aspects of trolley dilemma or its footbridge version and decided after
that.
Results show that in the control group 70% of people decided to
use the lever to change tracks for the running trolley, and 20% chose
to push the fat man down the tracks. In contrast, after experimental
manipulation almost no one decided to act. Also the decision time
difference between dilemmas disappeared after experimental
manipulation.
The result supports the idea of three co-working processes:
intuitive (TASS), paraformal (reflective mind) and algorithmic
process.
Abstract: The spreading characteristics of acoustically excited
swirling double-concentric jets were studied experimentally. The
central jet was acoustically excited at low and high pulsation
intensities. A smoke wire flow visualization and a hot-wire
anemometer velocity measurement results show that excitation forces
a vortex ring to roll-up from the edge of the central tube during each
excitation period. At low pulsation intensities, the vortex ring evolves
downstream, and eventually breaks up into turbulent eddies. At high
pulsation intensities, the primary vortex ring evolves and a series of
trailing vortex rings form during the same period of excitation. The
trailing vortex rings accelerate while evolving downstream and
overtake the primary vortex ring within the same cycle. In the
process, the primary vortex ring becomes unstable and breaks up
early. The effect of the fast traveling trailing vortex rings combined
with the swirl motion of the annular flow improve jet spreading
compared with the naturally evolving jets.
Abstract: Citizens are increasingly are provided with choice and
customization in public services and this has now also become a key
feature of higher education in terms of policy roll-outs on personal
development planning (PDP) and more generally as part of the
employability agenda. The goal here is to transform people, in this
case graduates, into active, responsible citizen-workers. A key part of
this rhetoric and logic is the inculcation of graduate attributes within
students. However, there has also been a concern with the issue of
student lack of engagement and perseverance with their studies. This
paper sets out to explore some of these conceptions that link graduate
attributes with citizenship as well as the notion of how identity is
forged through the higher education process. Examples are drawn
from a quality enhancement project that is being operated within the
context of the Scottish higher education system. This is further
framed within the wider context of competing and conflicting
demands on higher education, exacerbated by the current worldwide
economic climate. There are now pressures on students to develop
their employability skills as well as their capacity to engage with
global issues such as behavioural change in the light of
environmental concerns. It is argued that these pressures, in effect,
lead to a form of personalization that is concerned with how
graduates develop their sense of identity as something that is
engineered and re-engineered to meet these demands.
Abstract: A pilot plant for continuous flow microwave-assisted
chemical reaction combined with microreactors was developed and
water heating tests were conducted for evaluation of the developed
plant. We developed a microwave apparatus having a single
microwave generator that can heat reaction solutions in four reaction
fields simultaneously in order to increase throughput. We also
designed a four-branch waveguide using electromagnetic simulation,
and found that the transmission efficiency at 99%. Finally, we
developed the pilot plant using the developed microwave apparatus
and conducted water heating tests. The temperatures in the respective
reaction fields were controlled within ±1.1 K at 353.2 K. Moreover,
the energy absorption rates by the water were about 90% in the
respective reaction fields, whereas the energy absorption rate was
about 40% when 100 cm3 of water was heated by a commercially
available multimode microwave chemical reactor.
Abstract: This paper discusses the development of wireless
structure control of an induction motor scalar drives. This was
realised up on the wireless WiFi networks. This strategy of control is
ensured by the use of Wireless ad hoc networks and a virtual network
interface based on VNC which is used to make possible to take the
remote control of a PC connected on a wireless Ethernet network.
Verification of the proposed strategy of control is provided by
experimental realistic tests on scalar controlled induction motor
drives. The experimental results of the implementations with their
analysis are detailed.
Abstract: To understand the seismic behavior of the offshore
structures, the dynamic interaction of the water-structure-soil should
be assessed. In this regard the role of the water dynamic properties in
magnifying or reducing of the effects of earthquake induced motions
on offshore structures haven't been investigated in precise manner in
available literature. In this paper the sea water level fluctuations
effects on the seismic behavior of a sample of offshore structures has
been investigated by emphasizing on the water-structure interaction
phenomenon. For this purpose a two dimensional finite element
model of offshore structures as well as surrounded water has been
developed using ANSYS software. The effect of soil interaction with
embedded pile foundation has been imposed by using a series of
nonlinear springs in horizontal and vertical directions in soil-piles
contact points. In the model, the earthquake induced motions have
been applied on springs and consequently the motions propagated
upward to the structure and surrounded water. As a result of
numerical study, the horizontal deformations of the offshore deck as
well as internal force and buckling coefficient in structural elements
have been recorded and controlled with and without water presence.
In part of study a parametric study has been accomplished on sea
water level fluctuations and effect of this parameter has been studied
on the aforementioned numerical results.
Abstract: This work describes a CACSD tool for automatic design of robust controllers for hydraulic turbines. The tool calculates the optimal controller using the MATLAB hinfopt function and it
serves as a practical and effective solution for the laborious task of
designing a different controller for each type of turbine and generator, and different parameters and conditions of the plant. Results of the simulation of a generating unit subject to parameters
variation show the accuracy and efficiency of the obtained robust
controllers.
Abstract: Traffic incident has bad effect on all parts of society
so controlling road networks with enough traffic devices could help
to decrease number of accidents, so using the best method for
optimum site selection of these devices could help to implement good
monitoring system. This paper has considered here important criteria
for optimum site selection of traffic camera based on aggregation
methods such as Bagging and Dempster-Shafer concepts. In the first
step, important criteria such as annual traffic flow, distance from
critical places such as parks that need more traffic controlling were
identified for selection of important road links for traffic camera
installation, Then classification methods such as Artificial neural
network and Decision tree algorithms were employed for
classification of road links based on their importance for camera
installation. Then for improving the result of classifiers aggregation
methods such as Bagging and Dempster-Shafer theories were used.
Abstract: In this work, we treat the problems related to chemical and petrochemical plants of a certain complex process taking the centrifugal compressor as an example, a system being very complex by its physical structure as well as its behaviour (surge phenomenon). We propose to study the application possibilities of the recent control approaches to the compressor behaviour, and consequently evaluate their contribution in the practical and theoretical fields. Facing the studied industrial process complexity, we choose to make recourse to fuzzy logic for analysis and treatment of its control problem owing to the fact that these techniques constitute the only framework in which the types of imperfect knowledge can jointly be treated (uncertainties, inaccuracies, etc..) offering suitable tools to characterise them. In the particular case of the centrifugal compressor, these imperfections are interpreted by modelling errors, the neglected dynamics, no modelisable dynamics and the parametric variations. The purpose of this paper is to produce a total robust nonlinear controller design method to stabilize the compression process at its optimum steady state by manipulating the gas rate flow. In order to cope with both the parameter uncertainty and the structured non linearity of the plant, the proposed method consists of a linear steady state regulation that ensures robust optimal control and of a nonlinear compensation that achieves the exact input/output linearization.
Abstract: FACTS devices are used to control the power flow, to
increase the transmission capacity and to optimize the stability of the
power system. One of the most widely used FACTS devices is
Unified Power Flow Controller (UPFC). The controller used in the
control mechanism has a significantly effects on controlling of the
power flow and enhancing the system stability of UPFC. According
to this, the capability of UPFC is observed by using different control
mechanisms based on P, PI, PID and fuzzy logic controllers (FLC) in
this study. FLC was developed by taking consideration of Takagi-
Sugeno inference system in the decision process and Sugeno-s
weighted average method in the defuzzification process. Case studies
with different operating conditions are applied to prove the ability of
UPFC on controlling the power flow and the effectiveness of
controllers on the performance of UPFC. PSCAD/EMTDC program
is used to create the FLC and to simulate UPFC model.
Abstract: Regarding the multi-media property of internet and the facilities that can be provided for the users, the purpose of this paper is to investigate the users- behavioral patterns and the impact of internet on taboos of marriage. For this purpose a survey technique on the sample size amounted 403 students of governmental guidance schools of city of Mashhad in country of Iran were considered. The results showed, the process of using various internet environments depends on the degree of the users- familiarity with these sites. In order to clarify the effects of the Internet on the taboos of marriage, the non – internet parameters also considered to be controlled. The ttest held among the internet users and non-users, indicated that internet users possess lower taboos of marriage. Extraction of the effects of internet via considering the effects of non-internet parameters, indicate that addiction to the internet, creating a cordial atmosphere, emotional communication, and message attractive factors have significant effects on the family's traditional values.
Abstract: This paper focuses on the integration of hybrid renewable energy resources available in remote isolated islands of Sundarban-24 Parganas-South of Eastern part of India to National Grid of conventional power supply to give a Smart-Grid scenario. Before grid-integration, feasibility of optimization of hybrid renewable energy system is monitored through an Intelligent Controller proposed to be installed at Moushuni Island of Sundarban. The objective is to ensure the reliability and efficiency of the system to optimize the utilization of the hybrid renewable energy sources and also a proposition of how theses isolated Hybrid Renewable Energy Systems at remote islands can be grid-connected is analyzed towards vision of green smart-grid.
Abstract: There is a world-wide need for the development of sustainable management strategies to control pest infestation and the development of phosphine (PH3) resistance in lesser grain borer (Rhyzopertha dominica). Computer simulation models can provide a relatively fast, safe and inexpensive way to weigh the merits of various management options. However, the usefulness of simulation models relies on the accurate estimation of important model parameters, such as mortality. Concentration and time of exposure are both important in determining mortality in response to a toxic agent. Recent research indicated the existence of two resistance phenotypes in R. dominica in Australia, weak and strong, and revealed that the presence of resistance alleles at two loci confers strong resistance, thus motivating the construction of a two-locus model of resistance. Experimental data sets on purified pest strains, each corresponding to a single genotype of our two-locus model, were also available. Hence it became possible to explicitly include mortalities of the different genotypes in the model. In this paper we described how we used two generalized linear models (GLM), probit and logistic models, to fit the available experimental data sets. We used a direct algebraic approach generalized inverse matrix technique, rather than the traditional maximum likelihood estimation, to estimate the model parameters. The results show that both probit and logistic models fit the data sets well but the former is much better in terms of small least squares (numerical) errors. Meanwhile, the generalized inverse matrix technique achieved similar accuracy results to those from the maximum likelihood estimation, but is less time consuming and computationally demanding.
Abstract: The scroll pump belongs to the category of positive
displacement pump can be used for continuous pumping of gases at
low pressure apart from general vacuum application. The shape of
volume occupied by the gas moves and deforms continuously as the
spiral orbits. To capture flow features in such domain where mesh
deformation varies with time in a complicated manner, mesh less
solver was found to be very useful. Least Squares Kinetic Upwind
Method (LSKUM) is a kinetic theory based mesh free Euler solver
working on arbitrary distribution of points. Here upwind is enforced
in molecular level based on kinetic flux vector splitting scheme
(KFVS). In the present study we extended the LSKUM to moving
node viscous flow application. This new code LSKUM-NS-MN for
moving node viscous flow is validated for standard airfoil pitching
test case. Simulation performed for flow through scroll pump using
LSKUM-NS-MN code agrees well with the experimental pumping
speed data.
Abstract: This paper describes an expanded system for a servo
system design by using the Loop Shaping Design Procedure (LSDP).
LSDP is one of the H∞ design procedure. By conducting Loop
Shaping with a compensator and robust stabilization to satisfy the
index function, we get the feedback controller that makes the control
system stable. In this paper, we propose an expanded system for a
servo system design and apply to the DC motor. The proposed method
performs well in the DC motor positioning control. It has no
steady-state error in the disturbance response and it has robust
stability.
Abstract: This paper focuses on a critical component of the situational awareness (SA), the neural control of autonomous constant depth flight of an autonomous underwater vehicle (AUV). Autonomous constant depth flight is a challenging but important task for AUVs to achieve high level of autonomy under adverse conditions. The fundamental requirement for constant depth flight is the knowledge of the depth, and a properly designed controller to govern the process. The AUV, named VORAM, is used as a model for the verification of the proposed hybrid control algorithm. Three neural network controllers, named NARMA-L2 controllers, are designed for fast and stable diving maneuvers of chosen AUV model. This hybrid control strategy for chosen AUV model has been verified by simulation of diving maneuvers using software package Simulink and demonstrated good performance for fast SA in real-time searchand- rescue operations.
Abstract: The usefulness of weaning foods to meet the nutrient
needs of children is well recognized, and most of them are precooked
roller dried mixtures of cereal and/or legume flours which posses a
high viscosity and bulk when reconstituted. The objective of this study
was to formulate composite weaning foods using cereals, malted
legumes and vegetable powders and analyze them for nutrients,
functional properties and sensory attributes. Selected legumes (green
gram and lentil) were germinated, dried and dehulled. Roasted wheat,
rice, carrot powder and skim milk powder also were used. All the
ingredients were mixed in different proportions to get four
formulations, made into 30% slurry and dried in roller drier. The
products were analyzed for proximate principles, mineral content,
functional and sensory qualities. The results of analysis showed
following range of constituents per 100g of formulations on dry
weight basis, protein, 18.1-18.9 g ; fat, 0.78-1.36 g ; iron, 5.09-6.53
mg; calcium, 265-310 mg. The lowest water absorption capacity was
in case of wheat green gram based and the highest was in rice lentil
based sample. Overall sensory qualities of all foods were graded as
“good" and “very good" with no significant differences. The results
confirm that formulated weaning foods were nutritionally superior,
functionally appropriate and organoleptically acceptable.
Abstract: This paper presents a robust proportionalderivative
(PD) based cerebellar model articulation
controller (CMAC) for vertical take-off and landing flight
control systems. Successful on-line training and recalling
process of CMAC accompanying the PD controller is
developed. The advantage of the proposed method is mainly
the robust tracking performance against aerodynamic
parametric variation and external wind gust. The
effectiveness of the proposed algorithm is validated through
the application of a vertical takeoff and landing aircraft
control system.
Abstract: this paper focuses on designing of PSS and SVC
controller based on chaos and PSO algorithms to improve the
stability of power system. Single machine infinite bus (SMIB) system
with SVC located at the terminal of generator has been considered to
evaluate the proposed controllers where both SVC and PSS have the
same controller. The coefficients of PSS and SVC controller have
been optimized by chaos and PSO algorithms. Finally the system
with proposed controllers has been simulated for the special
disturbance in input power of generator, and then the dynamic
responses of generator have been presented. The simulation results
showed that the system composed with recommended controller has
outstanding operation in fast damping of oscillations of power system.