Abstract: A 15-storey RC building, studied in this paper, is
representative of modern building type constructed in Madina City in
Saudi Arabia before 10 years ago. These buildings are almost
consisting of reinforced concrete skeleton i.e. columns, beams and
flat slab as well as shear walls in the stairs and elevator areas
arranged in the way to have a resistance system for lateral loads
(wind – earthquake loads). In this study, the dynamic properties of
the 15-storey RC building were identified using ambient motions
recorded at several, spatially-distributed locations within each
building. Three dimensional pushover analysis (Nonlinear static
analysis) was carried out using SAP2000 software incorporating
inelastic material properties for concrete, infill and steel. The effect
of modeling the building with and without infill walls, on the
performance point as well as capacity and demand spectra due to EQ
design spectrum function in Madina area has been investigated. ATC-
40 capacity and demand spectra are utilized to get the modification
factor (R) for the studied building. The purpose of this analysis is to
evaluate the expected performance of structural systems by
estimating, strength and deformation demands in design, and
comparing these demands to available capacities at the performance
levels of interest. The results are summarized and discussed.
Abstract: In this current contribution, authors are dedicated to
investigate influence of the crystal lamellae orientation on
electromechanical behaviors of relaxor ferroelectric Poly
(vinylidene fluoride –trifluoroethylene -chlorotrifluoroethylene)
(P(VDF-TrFE-CTFE)) films by control of polymer microstructure,
aiming to picture the full map of structure-property relationship. In
order to define their crystal orientation films, terpolymer films were
fabricated by solution-casting, stretching and hot-pressing process.
Differential scanning calorimetry, impedance analyzer, and tensile
strength techniques were employed to characterize crystallographic
parameters, dielectric permittivity, and elastic Young’s modulus
respectively. In addition, large electrical induced out-of-plane
electrostrictive strain was obtained by cantilever beam mode.
Consequently, as-casted pristine films exhibited surprisingly high
electrostrictive strain 0.1774% due to considerably small value of
elastic Young’s modulus although relatively low dielectric
permittivity. Such reasons contributed to large mechanical elastic
energy density. Instead, due to 2 folds increase of elastic Young’s
modulus and less than 50% augmentation of dielectric constant, fullycrystallized
film showed weak electrostrictive behavior and
mechanical energy density as well. And subjected to mechanical
stretching process, Film C exhibited stronger dielectric constant and
out-performed electrostrictive strain over Film B because edge-on
crystal lamellae orientation induced by uniaxially mechanical stretch.
Hot-press films were compared in term of cooling rate. Rather large
electrostrictive strain of 0.2788% for hot-pressed Film D in
quenching process was observed although its dielectric permittivity
equivalent to that of pristine as-casted Film A, showing highest
mechanical elastic energy density value of 359.5 J/m3. In hot-press
cooling process, dielectric permittivity of Film E saw values at 48.8
concomitant with ca.100% increase of Young’s modulus. Films with
intermediate mechanical energy density were obtained.
Abstract: E-government has been adopted and used by many governments/countries around the world including Ghana to provide citizens and businesses with more accurate, real-time, and high quality services and information. The objective of this paper is to present an overview of the Government of Ghana’s (GoG) adoption and implement of e-government and its usage by the Ministries, Departments and its agencies (MDAs) as well as other public sector institutions to deliver efficient public service to the general public i.e. citizens, business etc. Government implementation of e-government focused on facilitating effective delivery of government service to the public and ultimately to provide efficient government-wide electronic means of sharing information and knowledge through a network infrastructure developed to connect all major towns and cities, Ministries, Departments and Agencies and other public sector organizations in Ghana. One aim for the Government of Ghana use of ICT in public administration is to improve productivity in government administration and service by facilitating exchange of information to enable better interaction and coordination of work among MDAs, citizens and private businesses. The study was prepared using secondary sources of data from government policy documents, national and international published reports, journal articles, and web sources. This study indicates that through the e-government initiative, currently citizens and businesses can access and pay for services such as renewal of driving license, business registration, payment of taxes, acquisition of marriage and birth certificates as well as application for passport through the GoG electronic service (eservice) and electronic payment (epay) portal. Further, this study shows that there is enormous commitment from GoG to adopt and implement e-government as a tool not only to transform the business of government but also to bring efficiency in public services delivered by the MDAs. To ascertain this, a further study need to be carried out to determine if the use of e-government has brought about the anticipated improvements and efficiency in service delivery of MDAs and other state institutions in Ghana.
Abstract: Energy has a prominent role for development of
nations. Countries which have energy resources also have strategic
power in the international trade of energy since it is essential for all
stages of production in the economy. Thus, it is important for
countries to analyze the weaknesses and strength of the system. On
the other side, international trade is one of the fields that are analyzed
as a complex network via network analysis. Complex network is one
of the tools to analyze complex systems with heterogeneous agents
and interaction between them. A complex network consists of nodes
and the interactions between these nodes. Total properties which
emerge as a result of these interactions are distinct from the sum of
small parts (more or less) in complex systems. Thus, standard
approaches to international trade are superficial to analyze these
systems. Network analysis provides a new approach to analyze
international trade as a network. In this network, countries constitute
nodes and trade relations (export or import) constitute edges. It
becomes possible to analyze international trade network in terms of
high degree indicators which are specific to complex networks such
as connectivity, clustering, assortativity/disassortativity, centrality,
etc. In this analysis, international trade of crude oil and coal which
are types of fossil fuel has been analyzed from 2005 to 2014 via
network analysis. First, it has been analyzed in terms of some
topological parameters such as density, transitivity, clustering etc.
Afterwards, fitness to Pareto distribution has been analyzed via
Kolmogorov-Smirnov test. Finally, weighted HITS algorithm has
been applied to the data as a centrality measure to determine the real
prominence of countries in these trade networks. Weighted HITS
algorithm is a strong tool to analyze the network by ranking countries
with regards to prominence of their trade partners. We have
calculated both an export centrality and an import centrality by
applying w-HITS algorithm to the data. As a result, impacts of the
trading countries have been presented in terms of high-degree
indicators.
Abstract: Nanofibers are defined as fibers with diameters less
than 100 nanometers. In this study, behaviours of activated carbon
nanofiber (ACNF), carbon nanofiber (CNF), polyacrylonitrile/ carbon
nanotube (PAN/CNT), polyvinyl alcohol/nanosilver (PVA/Ag) in
proton exchange membrane (PEM) fuel cells are investigated
experimentally. This material was used as gas diffusion layer (GDL)
in PEM fuel cells. In this study, the electrical conductivities of
nanofiber and nanofiber/nanoparticles have been studied to
understand their effects on PEM fuel cell performance. According to
the experimental results, the maximum electrical conductivity
performance of the fuel cell with nanofiber was found to be at
PVA/Ag (at UConn condition). The electrical conductivities of CNF,
ACNF, PAN/CNT are lower for PEM. The resistance of cell with
PVA/Ag is lower than the resistance of cell with PAN/CNT, ACNF,
CNF.
Abstract: The study of the aerodynamics related to the
improvement in the acting of airplanes and automobiles with the
objective of being reduced the effect of the attrition of the air on
structures, providing larger speeds and smaller consumption of fuel.
The application of the knowledge of the aerodynamics not more
limits to the aeronautical and automobile industries. Therefore, this
research aims to design and construction of a wind tunnel to perform
aerodynamic analysis in bodies of cars, seeking greater efficiency.
Therefore, this research aims to design and construction of a wind
tunnel to perform aerodynamic analysis in bodies of cars, seeking
greater efficiency. For this, a methodology for wind tunnel type
selection is designed to be built, taking into account the various
existing configurations in which chose to build an open circuit tunnel,
due to the lower complexity of construction and installation;
operational simplicity and low cost. The guidelines for the project
were teaching: the layer that limits study and analyze specimens with
different geometries. For the variation of pressure in the test, section
of a switched gauge used a pitot tube. Thus, it was possible to obtain
quantitative and qualitative results, which proved to be satisfactory.
Abstract: Multiple Sclerosis (MS) is a disease which affects the
central nervous system and causes balance problem. In clinical, this
disorder is usually evaluated using static posturography. Some linear
or nonlinear measures, extracted from the posturographic data (i.e.
center of pressure, COP) recorded during a balance test, has been
used to analyze postural control of MS patients. In this study, the
trend (TREND) and the sample entropy (SampEn), two nonlinear
parameters were chosen to investigate their relationships with the
expanded disability status scale (EDSS) score. 40 volunteers with
different EDSS scores participated in our experiments with eyes open
(EO) and closed (EC). TREND and 2 types of SampEn (SampEn1
and SampEn2) were calculated for each combined COP’s position
signal. The results have shown that TREND had a weak negative
correlation to EDSS while SampEn2 had a strong positive correlation
to EDSS. Compared to TREND and SampEn1, SampEn2 showed a
better significant correlation to EDSS and an ability to discriminate
the MS patients in the EC case. In addition, the outcome of the study
suggests that the multi-dimensional nonlinear analysis could provide
some information about the impact of disability progression in MS on
dynamics of the COP data.
Abstract: The study assessed the effectiveness of Pawpaw
(Carica papaya) wood in reducing the concentrations of heavy
metals in wastewater acting as a bio-sorbent. The following heavy
metals were considered; Zinc, Cadmium, Lead, Copper, Iron,
Selenium, Nickel and Manganese. The physiochemical properties of
Carica papaya stem were studied. The experimental sample was
sourced from the trunk of a felled matured pawpaw tree. Wastewater
for experimental use was prepared by dissolving soil samples
collected from a dump site at Owerri, Imo state of Nigeria in water.
The concentration of each metal remaining in solution as residual
metal after bio-sorption was determined using Atomic absorption
Spectrometer. The effects of pH and initial heavy metal concentration
were studied in a batch reactor. The results of Spectrometer test
showed that there were different functional groups detected in the
Carica papaya stem biomass. There was increase in metal removal as
the pH increased for all the metals considered except for Nickel and
Manganese. Optimum bio-sorption occurred at pH 5.9 with 5g/100ml
solution of bio-sorbent. The results of the study showed that the
treated wastewater is fit for irrigation purpose based on Canada
wastewater quality guideline for the protection of Agricultural
standard. This approach thus provides a cost effective and
environmentally friendly option for treating wastewater.
Abstract: Fermentation is well known as an essential process to
develop chocolate flavor in dried cocoa beans. Besides developing
the precursor of cocoa flavor, it also induces the color changes in the
beans. The fermentation process is influenced by various factors such
as planting material, preconditioning of cocoa pod and fermentation
technique. Therefore, this study was conducted to evaluate color of
Malaysian cocoa beans and how the duration of pods storage and
fermentation technique using shallow box will effect on its color
characteristics. There are two factors being studied i.e. duration of
cocoa pod storage (0, 2, 4 and 6 days) and duration of cocoa
fermentation (0, 1, 2, 3, 4 and 5 days). The experiment is arranged in
4 x 6 factorial designs with 24 treatments and arrangement is in a
Completely Randomised Design (CRD). The produced beans are
inspected for color changes under artificial light during cut test and
divided into four groups of color namely fully brown, purple brown,
fully purple and slaty. Cut tests indicated that cocoa beans which are
directly dried without undergone fermentation has the highest slaty
percentage. However, application of pods storage before fermentation
process is found to decrease the slaty percentage. In contrast, the
percentages of fully brown beans start to dominate after two days of
fermentation, especially from four and six days of pods storage batch.
Whereas, almost all batches of cocoa beans have a percentage of fully
purple less than 20%. Interestingly, the percentage of purple brown
beans are scattered in the entire beans batch regardless any specific
trend. Meanwhile, statistical analysis using General Linear Model
showed that the pods storage has a significant effect on the color
characteristic of the Malaysian dried beans compared to fermentation
duration.
Abstract: The field of instrumentation electronics is undergoing
an explosive growth, due to its wide range of applications. The
proliferation of electrical devices in a close working proximity can
negatively influence each other’s performance. The degradation in
the performance is due to electromagnetic interference (EMI). This paper investigates the negative effects of electromagnetic
interference originating in the General Purpose Interface Bus (GPIB)
control-network of the AC-DC transfer measurement system.
Remedial measures of reducing measurement errors and failure of
range of industrial devices due to EMI have been explored. The ACDC
transfer measurement system was analysed for the commonmode
(CM) EMI effects. Further investigation of coupling path as
well as much accurate identification of noise propagation mechanism
has been outlined. To prevent the occurrence of common-mode
(ground loops) which was identified between the GPIB system
control circuit and the measurement circuit, a microcontroller-driven
GPIB switching isolator device was designed, prototyped,
programmed and validated. This mitigation technique has been
explored to reduce EMI effectively.
Abstract: One of the main purposes of designing bucklingrestrained
braces is the fact that the entire lateral load is wasted by
the braces, the entire gravitational load is moved to the foundation
through the beams, and the columns can be moved to the foundation.
In other words, braces are designed for bearing lateral load. In the
implementation of the structure, it should be noted that the
implementation of various parts of the structure must be conducted in
such a way that the buckling-restrained braces would not bear the
gravitational load. Moreover, this type of brace has been investigated
under impact loading, and the design goals of designing method
(direct motion) are controlled under impact loading. The results of
dynamic analysis are shown as the relocation charts of the floors and
switch between the floors. Finally, the results are compared with each
other.
Abstract: With the advancement of knowledge about the utility
and impact of sustainability, its feasibility has been explored into
different walks of life. Scientists, however; have established their
knowledge in four areas viz environmental, economic, social and
cultural, popularly termed as four pillars of sustainability. Aspects of
environmental and economic sustainability have been rigorously
researched and practiced and huge volume of strong evidence of
effectiveness has been founded for these two sub-areas. For the social
and cultural aspects of sustainability, dependable evidence of
effectiveness is still to be instituted as the researchers and
practitioners are developing and experimenting methods across the
globe. Therefore, the present research aimed to identify globally used
practices of social and cultural sustainability and through evidence
synthesis assess their outcomes to determine the effectiveness of
those practices. A PICO format steered the methodology which
included all populations, popular sustainability practices including
walkability/cycle tracks, social/recreational spaces, privacy, health &
human services and barrier free built environment, comparators
included ‘Before’ and ‘After’, ‘With’ and ‘Without’, ‘More’ and
‘Less’ and outcomes included Social well-being, cultural coexistence,
quality of life, ethics and morality, social capital, sense of
place, education, health, recreation and leisure, and holistic
development. Search of literature included major electronic
databases, search websites, organizational resources, directory of
open access journals and subscribed journals. Grey literature,
however, was not included. Inclusion criteria filtered studies on the
basis of research designs such as total randomization, quasirandomization,
cluster randomization, observational or single studies
and certain types of analysis. Studies with combined outcomes were
considered but studies focusing only on environmental and/or
economic outcomes were rejected. Data extraction, critical appraisal
and evidence synthesis was carried out using customized tabulation,
reference manager and CASP tool. Partial meta-analysis was carried
out and calculation of pooled effects and forest plotting were done.
As many as 13 studies finally included for final synthesis explained
the impact of targeted practices on health, behavioural and social
dimensions. Objectivity in the measurement of health outcomes
facilitated quantitative synthesis of studies which highlighted the
impact of sustainability methods on physical activity, Body Mass
Index, perinatal outcomes and child health. Studies synthesized
qualitatively (and also quantitatively) showed outcomes such as
routines, family relations, citizenship, trust in relationships, social
inclusion, neighbourhood social capital, wellbeing, habitability and
family’s social processes. The synthesized evidence indicates slight
effectiveness and efficacy of social and cultural sustainability on the
targeted outcomes. Further synthesis revealed that such results of this
study are due weak research designs and disintegrated implementations. If architects and other practitioners deliver their
interventions in collaboration with research bodies and policy
makers, a stronger evidence-base in this area could be generated.
Abstract: Game-based learning can enhance the learning
motivation of students and provide a means for them to learn through
playing games. This study used augmented reality technology to
develop an interactive card game as a game-based teaching aid for
delivering elementary school science course content with the aim of
enhancing student learning processes and outcomes. Through playing
the proposed card game, students can familiarize themselves with
appearance, features, and foraging behaviors of insects. The system
records the actions of students, enabling teachers to determine their
students’ learning progress. In this study, 37 students participated in an
assessment experiment and provided feedback through questionnaires.
Their responses indicated that they were significantly more motivated
to learn after playing the game, and their feedback was mostly
positive.
Abstract: The objective of this study was to examine the
relationship between transformational leadership and innovative work
behavior and to evaluate the mediating role of leader-member
exchange relationships (LMX) on the assumed relationship. This
study has focused on the suggestion that LMX might emerge through
transformational leadership behaviors and thus could mediate the
relationship between transformational leadership and innovative
behavior. A cross-sectional survey research has been conducted on
the relationship these leadership approaches and their impact on
organizational HRM-outcomes have been conducted on two
organizations operating in the technical sector in Istanbul-Turkey.
The results of the research have supported the hypotheses.
Transformational leadership was positively related to the innovative
behaviors and LMX emerged to mediate that relationship.
Abstract: Currently, there are few user friendly Weigh-in-
Motion (WIM) data analysis softwares available which can produce
traffic input data for the recently developed AASHTOWare pavement
Mechanistic-Empirical (ME) design software. However, these
softwares have only rudimentary Quality Control (QC) processes.
Therefore, they cannot properly deal with erroneous WIM data. As
the pavement performance is highly sensible to the quality of WIM
data, it is highly recommended to use more refined QC process on
raw WIM data to get a good result. This study develops a userfriendly
software, which can produce traffic input for the ME design
software. This software takes the raw data (Class and Weight data)
collected from the WIM station and processes it with a sophisticated
QC procedure. Traffic data such as traffic volume, traffic distribution,
axle load spectra, etc. can be obtained from this software; which can
directly be used in the ME design software.
Abstract: Environmental concerns about the scarcity of marine
resources are critical driving forces for firms aiming to prepare their
supply chains for sustainability. Building on previous work, this
paper highlights the implementation of good practices geared towards
sustainable operations in the seafood department, which were
pursued in an exploratory retailer case. Outcomes of the adopted
environmentally and socially acceptable fish retailing strategies,
ranged from traceability, to self-certification and eco-labelling. The
consequences for business were, as follows: stronger collaboration
and trust across the chain of custody, improvement of sponsors’
image and of consumers’ loyalty and, progress in the Greenpeace
retailers’ evaluation ranking.
Abstract: The social logic of 'Sequina' slum area in Alexandria details the integral measure of space syntax at the room-level of twenty-building samples. The essence of spatial structure integrates the central 'visitor' domain with the 'living' frontage of the 'children' zone against the segregated privacy of the opposite 'parent' depth. Meanwhile, the multifunctioning of shallow rooms optimizes the integral 'visitor' structure through graph and visibility dimensions in contrast to the 'inhabitant' structure of graph-tails out of sight. Common theme of the layout integrity increases in compensation to the decrease of room visibility. Despite the 'pheno-type' of collective integration, the individual layouts observe 'geno-type' structure of spatial diversity per room adjoins. In this regard, the layout integrity alternates the cross-correlation of the 'kitchen & living' rooms with the 'inhabitant & visitor' domains of 'motherhood' dynamic structure. Moreover, the added 'grandparent' restructures the integral measure to become the deepest space, but opens to the 'living' of 'household' integrity. Some isomorphic layouts change the integral structure just through the 'balcony' extension of access, visual or ignored 'ringiness' of space syntax. However, the most integrated or segregated layouts invert the 'geno-type' into a shallow 'inhabitant' centrality versus the remote 'visitor' structure. Overview of the multivariate social logic of spatial integrity could never clarify without the micro-data analysis.
Abstract: This paper focuses on the study of DC-to-DC
converters, which are suitable for low-voltage high-power
applications. The output voltages generated by renewable energy
sources such as photovoltaic arrays and fuel cell stacks are
generally low and required to be increased to high voltage levels.
Development of DC-to-DC converters, which provide high step-up
voltage conversion ratios with high efficiencies and low voltage
stresses, is one of the main issues in the development of renewable
energy systems. A procedure for three converters−conventional
DC-to-DC converter, interleaved boost converter, and isolated flyback
based converter, is illustrated for a given set of specifications. The
selection among the converters for the given application is based on
the voltage conversion ratio, efficiency, and voltage stresses.
Abstract: Contemporary metropolitan areas and large cities are
dynamic, rapidly growing and continuously changing. Thus, urban
transformations and mutations are not a new phenomenon, but rather
a continuous process. Basic factors of urban transformation are
related to development of technologies, globalisation, lifestyle, etc.,
which in combination with local factors have generated an extremely
great variety of urban development conditions. This article discusses
the main urbanisation processes in Lithuania during last 50-year
period and social factors affecting urban functional mutations.
Abstract: Web Usage Mining is the application of data mining
techniques to find usage patterns from web log data, so as to grasp
required patterns and serve the requirements of Web-based
applications. User’s expertise on the internet may be improved by
minimizing user’s web access latency. This may be done by
predicting the future search page earlier and the same may be prefetched
and cached. Therefore, to enhance the standard of web
services, it is needed topic to research the user web navigation
behavior. Analysis of user’s web navigation behavior is achieved
through modeling web navigation history. We propose this technique
which cluster’s the user sessions, based on the K-medoids technique.