Abstract: Micro droplet formation is considered as a growing
emerging area of research due to its wide-range application in
chemistry as well as biology. The mechanism of micro droplet
formation using two immiscible liquids running through a T-junction
has been widely studied.
We believe that the flow of these two immiscible phases can be of
greater important factor that could have an impact on out-flow
hydrodynamic behavior, the droplets generated and the size of the
droplets. In this study, the type of the capillary tubes used also
represents another important factor that can have an impact on the
generation of micro droplets.
The tygon capillary tubing with hydrophilic inner surface doesn't
allow regular out-flows due to the fact that the continuous phase
doesn't adhere to the wall of the capillary inner surface.
Teflon capillary tubing, presents better wettability than tygon
tubing, and allows to obtain steady and regular regimes of out-flow,
and the micro droplets are homogeneoussize.
The size of the droplets is directly dependent on the flows of the
continuous and dispersed phases. Thus, as increasing the flow of the
continuous phase, to flow of the dispersed phase stationary, the size
of the drops decreases. Inversely, while increasing the flow of the
dispersed phase, to flow of the continuous phase stationary, the size
of the droplet increases.
Abstract: The most widely used semiconductor memory types
are the Dynamic Random Access Memory (DRAM) and Static
Random Access memory (SRAM). Competition among memory
manufacturers drives the need to decrease power consumption and
reduce the probability of read failure. A technology that is relatively
new and has not been explored is the FinFET technology. In this
paper, a single cell Schmitt Trigger Based Static RAM using FinFET
technology is proposed and analyzed. The accuracy of the result is
validated by means of HSPICE simulations with 32nm FinFET
technology and the results are then compared with 6T SRAM using
the same technology.
Abstract: As communications systems and technology become more advanced and complex, it will be increasingly important to focus on users- individual needs. Personalization and effective user profile management will be necessary to ensure the uptake and success of new services and devices and it is therefore important to focus on the users- requirements in this area and define solutions that meet these requirements. The work on personalization and user profiles emerged from earlier ETSI work on a Universal Communications Identifier (UCI) which is a unique identifier of the user rather than a range of identifiers of the many of communication devices or services (e.g. numbers of fixed phone at home/work, mobile phones, fax and email addresses). This paper describes work on personalization including standardized information and preferences and an architectural framework providing a description of how personalization can be integrated in Next Generation Networks, together with the UCI concept.
Abstract: We investigated the effects of modified
preprogrammed training mode Chase Trainer from Balance Trainer
(BT3, HurLab, Tampere, Finland) on athlete who experienced
unilateral Patellofemoral Pain Syndrome (PFPS). Twenty-seven
athletes with mean age= 14.23 ±1.31 years, height = 164.89 ± 7.85
cm, weight = 56.94 ± 9.28 kg were randomly assigned to two groups:
experiment (EG; n = 14) and injured (IG; n = 13). EG performed a
series of Chase Trainer program which required them to shift their
body weight at different directions, speeds and angle of leaning twice
a week for duration of 8 weeks. The static postural control and
perceived pain level measures were taken at baseline, after 6 weeks
and 8 weeks of training. There was no significant difference in any of
tested variables between EG and IG before and after 6-week the
intervention period. However, after 8-week of training, the postural
control (eyes open) and perceived pain level of EG improved
compared to IG (p
Abstract: Existing experiences indicate that one of the most
prominent reasons that some ERP implementations fail is related to
selecting an improper ERP package. Among those important factors
resulting in inappropriate ERP selections, one is to ignore preliminary
activities that should be done before the evaluation of ERP packages.
Another factor yielding these unsuitable selections is that usually
organizations employ prolonged and costly selection processes in
such extent that sometimes the process would never be finalized
or sometimes the evaluation team might perform many key final
activities in an incomplete or inaccurate way due to exhaustion, lack
of interest or out-of-date data. In this paper, a systematic approach
that recommends some activities to be done before and after the
main selection phase is introduced for choosing an ERP package. On
the other hand, the proposed approach has utilized some ideas that
accelerates the selection process at the same time that reduces the
probability of an erroneous final selection.
Abstract: With constraints on data availability and for study of power system stability it is adequate to model the synchronous generator with field circuit and one equivalent damper on q-axis known as the model 1.1. This paper presents a systematic procedure for modelling and simulation of a single-machine infinite-bus power system installed with a thyristor controlled series compensator (TCSC) where the synchronous generator is represented by model 1.1, so that impact of TCSC on power system stability can be more reasonably evaluated. The model of the example power system is developed using MATLAB/SIMULINK which can be can be used for teaching the power system stability phenomena, and also for research works especially to develop generator controllers using advanced technologies. Further, the parameters of the TCSC controller are optimized using genetic algorithm. The non-linear simulation results are presented to validate the effectiveness of the proposed approach.
Abstract: This paper presents the identification of the impact
force acting on a simply supported beam. The force identification is
an inverse problem in which the measured response of the structure is
used to determine the applied force. The identification problem is
formulated as an optimization problem and the genetic algorithm is
utilized to solve the optimization problem. The objective function is
calculated on the difference between analytical and measured
responses and the decision variables are the location and magnitude
of the applied force. The results from simulation show the
effectiveness of the approach and its robustness vs. the measurement
noise and sensor location.
Abstract: During the last few decades in the academic field, the
debate has increased on the effects of social geography on the
opportunities of socioeconomic integration. On one hand, it has been
discussed how the contents of the urban structure and social
geography affect not only the way people interact, but also their
chances of social and economic integration. On the other hand, it has
also been discussed how the urban structure is also constrained and
transformed by the action of social actors. Without questioning the
powerful influence of structural factors, related to the logic of the
production system, labor markets, education and training, the
research has shown the role played by place of residence in shaping
individual outcomes such as unemployment. In the context of this
debate the importance of territory of residence with respect to the
problem of unemployment has been highlighted.
Although statistics of unemployment have already demonstrated
the unequal incidence of the phenomenon in social groups, the issue
of uneven territorial impact on the phenomenon at intra-urban level
remains relatively unknown.
The purpose of this article is to show and to interpret the spatial
patterns of unemployment in the city of Porto using GIS (Geographic
Information System - GIS) technology. Under this analysis the
overlap of the spatial patterns of unemployment with the spatial
distribution of social housing, allows the discussion of the
relationship that occurs between these patterns and the reasons that
might explain the relative immutability of socioeconomic problems in
some neighborhoods.
Abstract: The objective of this paper is to present a research
study of the convectors that are used for heating or cooling of the
living room or industrial halls. The key points are experimental
measurement and comprehensive numerical simulation of the flow
coming throughout the part of the convector such as heat exchanger,
input from the fan etc.. From the obtained results, the components of
the convector are optimized in sense to increase thermal power
efficiency due to improvement of heat convection or reduction of air
drag friction. Both optimized aspects are leading to the more
effective service conditions and to energy saving. The significant part
of the convector research is a design of the unique measurement
laboratory and adopting measure techniques. The new laboratory
provides possibility to measure thermal power efficiency and other
relevant parameters under specific service conditions of the
convectors.
Abstract: The batch nature limits the standard kernel principal component analysis (KPCA) methods in numerous applications, especially for dynamic or large-scale data. In this paper, an efficient adaptive approach is presented for online extraction of the kernel principal components (KPC). The contribution of this paper may be divided into two parts. First, kernel covariance matrix is correctly updated to adapt to the changing characteristics of data. Second, KPC are recursively formulated to overcome the batch nature of standard KPCA.This formulation is derived from the recursive eigen-decomposition of kernel covariance matrix and indicates the KPC variation caused by the new data. The proposed method not only alleviates sub-optimality of the KPCA method for non-stationary data, but also maintains constant update speed and memory usage as the data-size increases. Experiments for simulation data and real applications demonstrate that our approach yields improvements in terms of both computational speed and approximation accuracy.
Abstract: WLAN Positioning has been presented by many
approaches in literatures using the characteristics of Received Signal
Strength (RSS), Time of Arrival (TOA) or Time Difference of
Arrival (TDOA), Angle of Arrival (AOA) and cell ID. Among these,
RSS approach is the simplest method to implement because there is
no need of modification on both access points and client devices
whereas its accuracy is terrible due to physical environments. For
TOA or TDOA approach, the accuracy is quite acceptable but most
researches have to modify either software or hardware on existing
WLAN infrastructure. The scales of modifications are made on only
access card up to the changes in protocol of WLAN. Hence, it is an
unattractive approach to use TOA or TDOA for positioning system.
In this paper, the new concept of merging both RSS and TOA
positioning techniques is proposed. In addition, the method to
achieve TOA characteristic for positioning WLAN user without any
extra modification necessarily appended in the existing system is
presented. The measurement results confirm that the proposed
technique using both RSS and TOA characteristics provides better
accuracy than using only either RSS or TOA approach.
Abstract: Thailand-s health system is challenged by the rising
number of patients and decreasing ratio of medical
practitioners/patients, especially in rural areas. This may tempt
inexperienced GPs to rush through the process of anamnesis with the
risk of incorrect diagnosis. Patients have to travel far to the hospital
and wait for a long time presenting their case. Many patients try to
cure themselves with traditional Thai medicine. Many countries are
making use of the Internet for medical information gathering,
distribution and storage. Telemedicine applications are a relatively
new field of study in Thailand; the infrastructure of ICT had
hampered widespread use of the Internet for using medical
information. With recent improvements made health and technology
professionals can work out novel applications and systems to help
advance telemedicine for the benefit of the people. Here we explore
the use of telemedicine for people with health problems in rural areas
in Thailand and present a Telemedicine Diagnosis System for Rural
Thailand (TEDIST) for diagnosing certain conditions that people
with Internet access can use to establish contact with Community
Health Centers, e.g. by mobile phone. The system uses a Web-based
input method for individual patients- symptoms, which are taken by
an expert system for the analysis of conditions and appropriate
diseases. The analysis harnesses a knowledge base and a backward
chaining component to find out, which health professionals should be
presented with the case. Doctors have the opportunity to exchange
emails or chat with the patients they are responsible for or other
specialists. Patients- data are then stored in a Personal Health Record.
Abstract: CDMA cellular networks support soft handover,
which guarantees the continuity of wireless services and enhanced
communication quality. Cellular networks support multimedia
services under varied propagation environmental conditions. In this
paper, we have shown the effect of characteristic parameters of the
cellular environments on the soft handover performance. We
consider path loss exponent, standard deviation of shadow fading and
correlation coefficient of shadow fading as the characteristic
parameters of the radio propagation environment. A very useful
statistical measure for characterizing the performance of mobile radio
system is the probability of outage. It is shown through numerical
results that above parameters have decisive effect on the probability
of outage and hence the overall performance of the soft handover
algorithm.
Abstract: Purpose: Planning and dosimetry of different VMAT algorithms (SmartArc, Ergo++, Autobeam) is compared with IMRT for Head and Neck Cancer patients. Modelling was performed to rule out the causes of discrepancies between planned and delivered dose. Methods: Five HNC patients previously treated with IMRT were re-planned with SmartArc (SA), Ergo++ and Autobeam. Plans were compared with each other and against IMRT and evaluated using DVHs for PTVs and OARs, delivery time, monitor units (MU) and dosimetric accuracy. Modelling of control point (CP) spacing, Leaf-end Separation and MLC/Aperture shape was performed to rule out causes of discrepancies between planned and delivered doses. Additionally estimated arc delivery times, overall plan generation times and effect of CP spacing and number of arcs on plan generation times were recorded. Results: Single arc SmartArc plans (SA4d) were generally better than IMRT and double arc plans (SA2Arcs) in terms of homogeneity and target coverage. Double arc plans seemed to have a positive role in achieving improved Conformity Index (CI) and better sparing of some Organs at Risk (OARs) compared to Step and Shoot IMRT (ss-IMRT) and SA4d. Overall Ergo++ plans achieved best CI for both PTVs. Dosimetric validation of all VMAT plans without modelling was found to be lower than ss-IMRT. Total MUs required for delivery were on average 19%, 30%, 10.6% and 6.5% lower than ss-IMRT for SA4d, SA2d (Single arc with 20 Gantry Spacing), SA2Arcs and Autobeam plans respectively. Autobeam was most efficient in terms of actual treatment delivery times whereas Ergo++ plans took longest to deliver. Conclusion: Overall SA single arc plans on average achieved best target coverage and homogeneity for both PTVs. SA2Arc plans showed improved CI and some OARs sparing. Very good dosimetric results were achieved with modelling. Ergo++ plans achieved best CI. Autobeam resulted in fastest treatment delivery times.
Abstract: E-learning refers to the specific kind of learning
experienced within the domain of educational technology, which can
be used in or out of the classroom. In this paper, we give an
overview of an e-learning platform 'An Innovative Interactive and
Online English Platform for Upper Primary Students' is an
interactive web-based application which will serve as an aid to the
primary school students in Mauritius. The objectives of this platform
are to offer quality learning resources for the English subject at our
primary level of education, encourage self-learning and hence
promote e-learning. The platform developed consists of several
interesting features, for example, the English Verb Conjugation tool,
Negative Form tool, Interrogative Form tool and Close Test
Generator. Thus, this learning platform will be useful at a time
where our country is looking for an alternative to private tuition and
also, looking forward to increase the pass rate.
Abstract: This paper presents a method to detect multiple cracks
based on frequency information. When a structure is subjected to
dynamic or static loads, cracks may develop and the modal
frequencies of the cracked structure may change. To detect cracks in a
structure, we construct a high precision wavelet finite element (EF)
model of a certain structure using the B-spline wavelet on the interval
(BSWI). Cracks can be modeled by rotational springs and added to the
FE model. The crack detection database will be obtained by solving
that model. Then the crack locations and depths can be determined
based on the frequency information from the database. The
performance of the proposed method has been numerically verified by
a rotor example.
Abstract: In recent years asymmetric cross section aluminum
alloy stock has been finding increasing use in various industrial manufacturing areas such as general structures and automotive
components. In these areas, components are generally required to have
complex curved configuration and, as such, a bending process is required during manufacture. Undesirable deformation in bending
processes such as flattening or wrinkling can easily occur when thin-walled sections are bent. Hence, a thorough understanding of the
bending behavior of such sections is needed to prevent these undesirable deformations. In this study, the bending behavior of
asymmetric channel section was examined using finite element analysis (FEA). Typical methods of preventing undesirable
deformation, such as asymmetric laminated elastic mandrels were included in FEA model of draw bending. Additionally, axial tension
was applied to prevent wrinkling. By utilizing the FE simulations effect of restriction dies and axial tension on undesirable deformation during the process was clarified.
Abstract: Based on a global kinetics of direct dimethyl ether (DME) synthesis process from syngas, a steady-state one-dimensional mathematical model for the bubble column slurry reactor (BCSR) has been established. It was built on the assumption of plug flow of gas phase, sedimentation-dispersion model of catalyst grains and isothermal chamber regardless of reaction heats and rates for the design of an industrial scale bubble column slurry reactor. The simulation results indicate that higher pressure and lower temperature were favorable to the increase of CO conversion, DME selectivity, products yield and the height of slurry bed, which has a coincidence with the characteristic of DME synthesis reaction system, and that the height of slurry bed is lessen with the increasing of operation temperature in the range of 220-260℃. CO conversion, the optimal operation conditions in BCSR were proposed.
Abstract: This paper presents a large scale, quantitative investigation of the impact of discipline differences on the student experience of using an online learning environment (OLE). Based on a representative sample of 2526 respondents, a number of significant differences in the mean rating by broad discipline area of the importance of, and satisfaction with, a range of elements of an OLE were found. Broadly speaking, the Arts and Science and Technology discipline areas reported the lowest importance and satisfaction ratings for the OLE, while the Health and Behavioural Sciences area was the most satisfied with the OLE. A number of specific, systematic discipline differences are reported and discussed. Compared to the observed significant differences in mean importance ratings, there were fewer significant differences in mean satisfaction ratings, and those that were observed were less systematic than for importance ratings.
Abstract: The V-notches are most possible case for initiation of cracks in parts. The specifications of cracks on the tip of the notch will be influenced via opening angle, tip radius and depth of V-notch. In this study, the effects of V-notch-s opening angle on stress intensity factor and T-stress of crack on the notch has been investigated. The experiment has been done in different opening angles and various crack length in mode (I) loading using Photoelasticity method. The results illustrate that while angle increases in constant crack-s length, SIF and T-stress will decrease. Beside, the effect of V-notch angle in short crack is more than long crack. These V-notch affects are negligible by increasing the length of crack, and the crack-s behavior can be considered as a single-edge crack specimen. Finally, the results have been evaluated with numerical finite element analysis and good agreement was obvious.