Abstract: In the present work, forming limit diagrams and strain
distribution profile diagrams for extra deep drawing steel at room and
elevated temperatures have been determined experimentally by
conducting stretch forming experiments by using designed and
fabricated warm stretchforming tooling setup. With the help of
forming Limit Diagrams (FLDs) and strain, distribution profile
diagrams the formability of Extra Deep Drawing steel has been
analyzed and co-related with mechanical properties like strain
hardening COEFFICIENT (n) and normal anisotropy (r−). Mechanical
properties of EDD steel from room temperature to 4500C were
determined and discussed the impact of temperature on the properties
like work hardening exponent (n) anisotropy (r-) and strength
coefficient of the material. In addition, the fractured surfaces after
stretching have undergone the some metallurgical investigations and
attempt has been made to co-relate with the formability of EDD steel
sheets. They are co-related and good agreement with FLDs at various
temperatures.
Abstract: This article developed an ion thruster optic system
sputter erosion depth numerical 3D model by IFE-PIC (Immersed
Finite Element-Particle-in-Cell) and Mont Carlo method, and
calculated the downstream surface sputter erosion rate of accelerator
grid; compared with LIPS-200 life test data. The results of the
numerical model are in reasonable agreement with the measured data.
Finally, we predicted the lifetime of the 20cm diameter ion thruster via
the erosion data obtained with the model. The ultimate result
demonstrated that under normal operating condition, the erosion rate
of the grooves wears on the downstream surface of the accelerator grid
is 34.6μm⁄1000h, which means the conservative lifetime until
structural failure occurring on the accelerator grid is 11500 hours.
Abstract: This study evaluated to facilitate separation of ABS
plastics from other waste plastics by froth flotation after surface
hydrophilization of ABS with heat treatment. The mild heat treatment
at 100oC for 60s could selectively increase the hydrophilicity of the
ABS plastics surface (i.e., ABS contact angle decreased from 79o to
65.8o) among other plastics mixture. The SEM and XPS results of
plastic samples sufficiently supported the increase in hydrophilic
functional groups and decrease contact angle on ABS surface, after
heat treatment. As a result of the froth flotation (at mixing speed 150
rpm and airflow rate 0.3 L/min) after heat treatment, about 85% of
ABS was selectively separated from other heavy plastics with 100%
of purity. The effect of optimum treatment condition and detailed
mechanism onto separation efficiency in the froth floatation was also
investigated. This research is successful in giving a simple, effective,
and inexpensive method for ABS separation from waste plastics.
Abstract: The purposes of this study were to: 1) investigate
operation conditions of SME automotive part industry in Bangkok
and vicinity and 2) to compare operation problem levels of SME
automotive part industry in Bangkok and vicinity according to the
sizes of the enterprises. Samples in this study included 196
entrepreneurs of SME automotive part industry in Bangkok and
vicinity derived from simple random sampling and calculation from
R. V. Krejcie and D. W. Morgan’s tables. Research statistics included
frequency, percentage, mean, standard deviation, and T-test. The
results revealed that in general the problem levels of SME automotive
part industry in Bangkok and vicinity were high. When considering
in details, it was found that the problem levels were high at every
aspect, i.e. personal, production, export, finance, and marketing
respectively. The comparison of the problem levels according to the
sizes of the enterprises revealed statistically significant differences at
.05. When considering on each aspect, it was found that the aspect
with the statistical difference at .05 included 5 aspects, i.e.
production, marketing, finance, personal, and export. The findings
also showed that small enterprises faced more severe problems than
those of medium enterprises.
Abstract: The increase in electric power demand in face of
environmental issues has intensified the participation of renewable
energy sources such as photovoltaics, in the energy matrix of various
countries. Due to their operational characteristics, they can generate
time-varying harmonic and inter-harmonic distortions. For this
reason, the application of methods of measurement based on
traditional Fourier analysis, as proposed by IEC 61000-4-7, can
provide inaccurate results. Considering the aspects mentioned herein,
came the idea of the development of this work which aims to present
the results of a comparative evaluation between a methodology
arising from the combination of the Prony method with the Kalman
filter and another method based on the IEC 61000-4-30 and IEC
61000-4-7 standards. Employed in this study were synthetic signals
and data acquired through measurements in a 50kWp photovoltaic
installation.
Abstract: The quality of concrete is usually defined by compressive strength, but flexural strength is the most important characteristic of concrete in a pavement which control the mix design of concrete instead of compressive strength. Therefore, the aggregates which are selected for the pavements are affected by higher flexural strength. Roller Compacting Concrete Pavement (RCCP) is not a new construction method. The other characteristic of this method is no bleeding and less shrinkage due to the lower amount of water. For this purpose, a roller is needed for placing and compacting. The surface of RCCP is not smooth; therefore, the most common use of this pavement is in an industrial zone with slower traffic speed which requires durable and tough pavement. For preparing a smoother surface, it can be achieved by asphalt paver. RCCP decrease the finishing cost because there are no bars, formwork, and the lesser labor need for placing the concrete. In this paper, different aspect of RCCP such as mix design, flexural, compressive strength and focus on the different part of RCCP on detail have been investigated.
Abstract: Social networking sites such as Twitter and Facebook
attracts over 500 million users across the world, for those users, their
social life, even their practical life, has become interrelated. Their
interaction with social networking has affected their life forever.
Accordingly, social networking sites have become among the main
channels that are responsible for vast dissemination of different kinds
of information during real time events. This popularity in Social
networking has led to different problems including the possibility of
exposing incorrect information to their users through fake accounts
which results to the spread of malicious content during life events.
This situation can result to a huge damage in the real world to the
society in general including citizens, business entities, and others. In this paper, we present a classification method for detecting the
fake accounts on Twitter. The study determines the minimized set of
the main factors that influence the detection of the fake accounts on
Twitter, and then the determined factors are applied using different
classification techniques. A comparison of the results of these
techniques has been performed and the most accurate algorithm is
selected according to the accuracy of the results. The study has been
compared with different recent researches in the same area; this
comparison has proved the accuracy of the proposed study. We claim
that this study can be continuously applied on Twitter social network
to automatically detect the fake accounts; moreover, the study can be
applied on different social network sites such as Facebook with minor
changes according to the nature of the social network which are
discussed in this paper.
Abstract: Carbon dioxide is one of the major greenhouse gas
(GHG) contributors. It is an obligation of the industry to reduce the
amount of carbon dioxide emission to the acceptable limits.
Tremendous research and studies are reported in the past and still the
quest to find the suitable and economical solution of this problem
needed to be explored in order to develop the most plausible absorber
for carbon dioxide removal. Amino acids can be potential alternate
solvents for carbon dioxide capture from gaseous streams. This is due
to its ability to resist oxidative degradation, low volatility and its
ionic structure. In addition, the introduction of promoter-like
piperazine to amino acid helps to further enhance the solubility. In
this work, the effect of piperazine on thermo physical properties and
solubility of β-Alanine aqueous solutions were studied for various
concentrations. The measured physicochemical properties data was
correlated as a function of temperature using least-squares method
and the correlation parameters are reported together with it respective
standard deviations. The effect of activator piperazine on the CO2
loading performance of selected amino acid under high-pressure
conditions (1bar to 10bar) at temperature range of (30 to 60)oC was
also studied. Solubility of CO2 decreases with increasing temperature
and increases with increasing pressure. Quadratic representation of
solubility using Response Surface Methodology (RSM) shows that
the most important parameter to optimize solubility is system
pressure. The addition of promoter increases the solubility effect of
the solvent.
Abstract: A myriad of environmental issues face the Nigerian
industrial region, resulting from; oil and gas production, mining,
manufacturing and domestic wastes. Amidst these, much effort has
been directed by stakeholders in the Nigerian oil producing regions,
because of the impacts of the region on the wider Nigerian economy.
Although collaborative environmental management has been noted as
an effective approach in managing environmental issues, little
attention has been given to the roles and practices of stakeholders in
effecting a collaborative environmental management framework for
the Nigerian oil-producing region. This paper produces a framework
to expand and deepen knowledge relating to stakeholders aspects of
collaborative roles in managing environmental issues in the Nigeria
oil-producing region. The knowledge is derived from analysis of
stakeholders’ practices – studied through multiple case studies using
document analysis. Selected documents of key stakeholders –
Nigerian government agencies, multi-national oil companies and host
communities, were analyzed. Open and selective coding was
employed manually during document analysis of data collected from
the offices and websites of the stakeholders. The findings showed
that the stakeholders have a range of roles, practices, interests, drivers
and barriers regarding their collaborative roles in managing
environmental issues. While they have interests for efficient resource
use, compliance to standards, sharing of responsibilities, generating
of new solutions, and shared objectives; there is evidence of major
barriers and these include resource allocation, disjointed policy,
ineffective monitoring, diverse socio- economic interests, lack of
stakeholders’ commitment and limited knowledge sharing. However,
host communities hold deep concerns over the collaborative roles of
stakeholders for economic interests, particularly, where government
agencies and multi-national oil companies are involved. With these
barriers and concerns, a genuine stakeholders’ collaboration is found
to be limited, and as a result, optimal environmental management
practices and policies have not been successfully implemented in the
Nigeria oil-producing region. A framework is produced that describes
practices that characterize collaborative environmental management
might be employed to satisfy the stakeholders’ interests. The
framework recommends critical factors, based on the findings, which
may guide a collaborative environmental management in the oil
producing regions. The recommendations are designed to re-define
the practices of stakeholders in managing environmental issues in the
oil producing regions, not as something wholly new, but as an
approach essential for implementing a sustainable environmental
policy. This research outcome may clarify areas for future research as
well as to contribute to industry guidance in the area of collaborative
environmental management.
Abstract: In the present study, feasibility of the selective surface
hydrophilization of polyvinyl chloride (PVC) by microwave treatment
was evaluated to facilitate the separation from automotive shredder
residue (ASR), by the froth flotation. The combination of 60 sec
microwave treatment with PAC, a sharp and significant decrease about
16.5° contact angle of PVC was observed in ASR plastic compared
with other plastics. The microwave treatment with the addition of PAC
resulted in a synergetic effect for the froth flotation, which may be a
result of the 90% selective separation of PVC from ASR plastics, with
82% purity. While, simple mixing with a nanometallic Ca/CaO/PO4
dispersion mixture immobilized 95-100% of heavy metals in ASR
soil/residues. The quantity of heavy metals leached from thermal
residues after treatment by nanometallic Ca/CaO/PO4 was lower than
the Korean standard regulatory limit for hazardous waste landfills.
Microwave treatment can be a simple and effective method for PVC
separation from ASR plastics.
Abstract: In order to utilize results from global climate models,
dynamical and statistical downscaling techniques have been
developed. For dynamical downscaling, usually a limited area
numerical model is used, with associated high computational cost.
This research proposes dynamic equation for specific space-time
regional climate downscaling from the Educational Global Climate
Model (EdGCM) for Southeast Asia. The equation is for surface air
temperature. This equation provides downscaling values of surface
air temperature at any specific location and time without running a
regional climate model. In the proposed equations, surface air
temperature is approximated from ground temperature, sensible heat
flux and 2m wind speed. Results from the application of the equation
show that the errors from the proposed equations are less than the
errors for direct interpolation from EdGCM.
Abstract: The study is the way to identify the problems that
occur in organizing short course’s lifelong learning in the information
and communication technology (ICT) education which are faced by
the lecturer and staff at the Mara Skill Institute and Industrial
Training Institute in Pahang Malaysia. The important aspects of these
issues are classified to five which are selecting the courses
administrative. Fifty lecturers and staff were selected as a respondent.
The sample is selected by using the non-random sampling method
purpose sampling. The questionnaire is used as a research instrument
and divided into five main parts. All the data that gain from the
questionnaire are analyzed by using the SPSS in term of mean,
standard deviation and percentage. The findings showed, there are the
problems occur in organizing the short course for lifelong learning in
ICT education.
Abstract: The change of conditions for production companies in
high-wage countries is characterized by the globalization of
competition and the transition of a supplier´s to a buyer´s market. The
companies need to face the challenges of reacting flexibly to these
changes. Due to the significant and increasing degree of automation,
assembly has become the most expensive production process.
Regarding the reduction of production cost, assembly consequently
offers a considerable rationalizing potential. Therefore, an
aerodynamic feeding system has been developed at the Institute of
Production Systems and Logistics (IFA), Leibniz Universitaet
Hannover. This system has been enabled to adjust itself by using a
genetic algorithm. The longer this genetic algorithm is executed the
better is the feeding quality. In this paper, the relation between the
system´s setting time and the feeding quality is observed and a
function which enables the user to achieve the minimum of the total
feeding time is presented.
Abstract: The paper focuses on the benefits of business process
modeling. Although this discipline is developing for many years,
there is still necessity of creating new opportunities to meet the ever
increasing users’ needs. Because one of these needs is related to the
conversion of business process models from one standard to another,
the authors have developed a converter between BPMN and EPC
standards using workflow patterns as intermediate tool. Nowadays
there are too many systems for business process modeling. The
variety of output formats is almost the same as the systems
themselves. This diversity additionally hampers the conversion of the
models. The presented study is aimed at discussing problems due to
differences in the output formats of various modeling environments.
Abstract: The main purpose of this study is to assess the
sediment quality and potential ecological risk in marine sediments in
Gymea Bay located in south Sydney, Australia. A total of 32 surface
sediment samples were collected from the bay. Current track
trajectories and velocities have also been measured in the bay. The
resultant trace elements were compared with the adverse biological
effect values Effect Range Low (ERL) and Effect Range Median
(ERM) classifications. The results indicate that the average values of
chromium, arsenic, copper, zinc, and lead in surface sediments all
reveal low pollution levels and are below ERL and ERM values. The
highest concentrations of trace elements were found close to
discharge points and in the inner bay, and were linked with high
percentages of clay minerals, pyrite and organic matter, which can
play a significant role in trapping and accumulating these elements.
The lowest concentrations of trace elements were found to be on the
shoreline of the bay, which contained high percentages of sand
fractions. It is postulated that the fine particles and trace elements are
disturbed by currents and tides, then transported and deposited in
deeper areas. The current track velocities recorded in Gymea Bay had
the capability to transport fine particles and trace element pollution
within the bay. As a result, hydrodynamic measurements were able to
provide useful information and to help explain the distribution of
sedimentary particles and geochemical properties. This may lead to
knowledge transfer to other bay systems, including those in remote
areas. These activities can be conducted at a low cost, and are
therefore also transferrable to developing countries. The advent of
portable instruments to measure trace elements in the field has also
contributed to the development of these lower cost and easily applied
methodologies available for use in remote locations and low-cost
economies.
Abstract: Response Surface Methods (RSM) provide
statistically validated predictive models that can then be manipulated
for finding optimal process configurations. Variation transmitted to
responses from poorly controlled process factors can be accounted
for by the mathematical technique of propagation of error (POE),
which facilitates ‘finding the flats’ on the surfaces generated by
RSM. The dual response approach to RSM captures the standard
deviation of the output as well as the average. It accounts for
unknown sources of variation. Dual response plus propagation of
error (POE) provides a more useful model of overall response
variation. In our case, we implemented this technique in predicting
compressive strength of concrete of 28 days in age. Since 28 days is
quite time consuming, while it is important to ensure the quality
control process. This paper investigates the potential of using design
of experiments (DOE-RSM) to predict the compressive strength of
concrete at 28th day. Data used for this study was carried out from
experiment schemes at university of Benghazi, civil engineering
department. A total of 114 sets of data were implemented. ACI mix
design method was utilized for the mix design. No admixtures were
used, only the main concrete mix constituents such as cement, coarseaggregate,
fine aggregate and water were utilized in all mixes.
Different mix proportions of the ingredients and different water
cement ratio were used. The proposed mathematical models are
capable of predicting the required concrete compressive strength of
concrete from early ages.
Abstract: The aim of this paper is to propose a general
framework for storing, analyzing, and extracting knowledge from
two-dimensional echocardiographic images, color Doppler images,
non-medical images, and general data sets. A number of high
performance data mining algorithms have been used to carry out this
task. Our framework encompasses four layers namely physical
storage, object identification, knowledge discovery, user level.
Techniques such as active contour model to identify the cardiac
chambers, pixel classification to segment the color Doppler echo
image, universal model for image retrieval, Bayesian method for
classification, parallel algorithms for image segmentation, etc., were
employed. Using the feature vector database that have been
efficiently constructed, one can perform various data mining tasks
like clustering, classification, etc. with efficient algorithms along
with image mining given a query image. All these facilities are
included in the framework that is supported by state-of-the-art user
interface (UI). The algorithms were tested with actual patient data
and Coral image database and the results show that their performance
is better than the results reported already.
Abstract: This paper presents the results of a study on the
influence of varying percentages of rock bridges along a basal surface
defining a biplanar failure mode. A pseudo-coupled-hydromechanical
brittle fracture analysis is adopted using the state-of-the-art code
Slope Model. Model results show that rock bridge failure is strongly
influenced by the incorporation of groundwater pressures. The
models show that groundwater pressure can promote total failure of a
5% rock bridge along the basal surface. Once the percentage of the
rock bridges increases to 10 and 15%, although, the rock bridges are
broken, full interconnection of the surface defining the basal surface
of the biplanar mode does not occur. Increased damage is caused
when the rock bridge is located at the daylighting end of the basal
surface in proximity to the blast damage zone. As expected, some
cracking damage is experienced in the blast damage zone, where
properties representing a good quality controlled damage blast
technique were assumed. Model results indicate the potential increase
of permeability towards the blast damage zone.
Abstract: In this work, our goal is to optimize the nitriding treatment at a low-temperature of the steel 32CrMoV13 using gas mixtures of ammonia, nitrogen and hydrogen to improve the mechanical properties of the surface (good wear resistance, friction and corrosion), and of the diffusion layer of the nitrogen (good resistance to fatigue and good tenacity with heart). By limiting our work to the pure iron and to the alloys iron-chromium and iron-chromium-carbon, we have studied the various parameters which manage the nitriding: flow rate and composition of the gaseous phase, the interaction chromium-nitrogen and chromium-carbon by the help of experiments of nitriding realized in the laboratory by thermogravimetry. The acquired knowledge has been applied by the mastery of the growth of the γ' combination layer on the α diffusion layer in the case of the industrial steel 32CrMoV13.
Abstract: A three-dimensional numerical simulation of flow
through mini and microchannels with designed roughness is
conducted here. The effect of the roughness height (surface
roughness), geometry, Reynolds number on the friction factor, and
Nusselt number is investigated. The study is carried out by
employing CFD software, CFX. Our work focuses on a water flow
inside a circular mini-channel of 1 mm and microchannels of 500 and
100 m in diameter. The speed entry varies from 0.1 m/s to 20 m/s.
The general trend can be observed that bigger sizes of roughness
element lead to higher flow resistance. It is found that the friction
factor increases in a nonlinear fashion with the increase in obstruction
height. Particularly, the effect of roughness can no longer be ignored
at relative roughness height higher than 3%. A significant increase in
Poiseuille number is detected for all configurations considered. The
same observation can be done for Nusselt number. The transition
zone between laminar and turbulent flow depends on the channel
diameter.