Abstract: Genetic algorithms (GAs) have been widely used for
global optimization problems. The GA performance depends highly
on the choice of the search space for each parameter to be optimized.
Often, this choice is a problem-based experience. The search space
being a set of potential solutions may contain the global optimum
and/or other local optimums. A bad choice of this search space
results in poor solutions. In this paper, our approach consists in
extending the search space boundaries during the GA optimization,
only when it is required. This leads to more diversification of GA
population by new solutions that were not available with fixed search
space boundaries. So, these dynamic search spaces can improve the
GA optimization performances. The proposed approach is applied to
power system stabilizer optimization for multimachine power system
(16-generator and 68-bus). The obtained results are evaluated and
compared with those obtained by ordinary GAs. Eigenvalue analysis
and nonlinear system simulation results show the effectiveness of the
proposed approach to damp out the electromechanical oscillation and
enhance the global system stability.
Abstract: In this paper, an extended method of the directionally constrained minimization of power (DCMP) algorithm for broadband signals is proposed. The DCMP algorithm is one of the useful techniques of extracting a target signal from observed signals of a microphone array system. In the DCMP algorithm, output power of the microphone array is minimized under a constraint of constant responses to directions of arrival (DOAs) of specific signals. In our algorithm, by limiting the directional constraint to the perpendicular direction to the sensor array system, the calculating time is reduced.
Abstract: We propose a new perspective on speech
communication using blind source separation. The original speech is
mixed with key signals which consist of the mixing matrix, chaotic
signals and a random noise. However, parts of the keys (the mixing
matrix and the random noise) are not necessary in decryption. In
practice implement, one can encrypt the speech by changing the noise
signal every time. Hence, the present scheme obtains the advantages
of a One Time Pad encryption while avoiding its drawbacks in key
exchange. It is demonstrated that the proposed scheme is immune
against traditional attacks.
Abstract: We present a novel scheme to recognize isolated speech
signals using certain statistical parameters derived from those signals.
The determination of the statistical estimates is based on extracted
signal information rather than the original signal information in
order to reduce the computational complexity. Subtle details of
these estimates, after extracting the speech signal from ambience
noise, are first exploited to segregate the polysyllabic words from
the monosyllabic ones. Precise recognition of each distinct word is
then carried out by analyzing the histogram, obtained from these
information.
Abstract: EcoDam is an adenine-N6 DNA methyltransferase
that methylates the GATC sites in the Escherichia coli genome.
DNA-adenine methylation is not present in higher eukaryotes
including humans. These observations raise the possibility that dam
inhibitors may be used as anti-microbial agents. Polyphosphate
(Poly(P)) is an important metabolite and signaling molecule in
prokaryotes and eukaryotes. Here, by using gel retardation
experiments to investigate the competition of DNA binding by
EcoDam in the presence of polyphosphate, we found that Poly (P)
strongly interferes with DNA binding by EcoDam, while same
concentration of monophosphate does not. In addition, we
demonstrated that Poly (P) binding inhibits the activity of EcoDam
and our results suggest that Poly (P) led to strong inhibition of the
EcoDam catalytic activity, while monophosphate had only moderate
effect.
Abstract: This paper describes the development of a WLAN
propagation model, using Spectral Analyzer measurements. The
signal is generated by two Access Points (APs) on the base floor at
the administrative Communication School of ESPOL building. In
general, users do not have a Q&S reference about a wireless network;
however, this depends on the level signal as a function of frequency,
distance and other path conditions between receiver and transmitter.
Then, power density of the signal decrease as it propagates through
space and data transfer rate is affected. This document evaluates and
implements empirical mathematical formulation for the
characterization of WLAN radio wave propagation on two aisles of
the building base floor.
Abstract: This paper proposes an alternative control mechanism
for an interactive Pan/Tilt/Zoom (PTZ) camera control system.
Instead of using a mouse or a joystick, the proposed mechanism
utilizes a Nintendo Wii remote and infrared (IR) sensor bar. The Wii
remote has buttons that allows the user to control the movement of a
PTZ camera through Bluetooth connectivity. In addition, the Wii
remote has a built-in motion sensor that allows the user to give
control signals to the PTZ camera through pitch and roll movement.
A stationary IR sensor bar, placed at some distance away opposite the
Wii remote, enables the detection of yaw movement. In addition, the
Wii remote-s built-in IR camera has the ability to detect its spatial
position, and thus generates a control signal when the user moves the
Wii remote. Some experiments are carried out and their performances
are compared with an industry-standard PTZ joystick.
Abstract: The quality of a machined surface is becoming more and more important to justify the increasing demands of sophisticated component performance, longevity, and reliability. Usually, any machining operation leaves its own characteristic evidence on the machined surface in the form of finely spaced micro irregularities (surface roughness) left by the associated indeterministic characteristics of the different elements of the system: tool-machineworkpart- cutting parameters. However, one of the most influential sources in machining affecting surface roughness is the instantaneous state of tool edge. The main objective of the current work is to relate the in-process immeasurable cutting edge deformation and surface roughness to a more reliable easy-to-measure force signals using a robust non-linear time-dependent modeling regression techniques. Time-dependent modeling is beneficial when modern machining systems, such as adaptive control techniques are considered, where the state of the machined surface and the health of the cutting edge are monitored, assessed and controlled online using realtime information provided by the variability encountered in the measured force signals. Correlation between wear propagation and roughness variation is developed throughout the different edge lifetimes. The surface roughness is further evaluated in the light of the variation in both the static and the dynamic force signals. Consistent correlation is found between surface roughness variation and tool wear progress within its initial and constant regions. At the first few seconds of cutting, expected and well known trend of the effect of the cutting parameters is observed. Surface roughness is positively influenced by the level of the feed rate and negatively by the cutting speed. As cutting continues, roughness is affected, to different extents, by the rather localized wear modes either on the tool nose or on its flank areas. Moreover, it seems that roughness varies as wear attitude transfers from one mode to another and, in general, it is shown that it is improved as wear increases but with possible corresponding workpart dimensional inaccuracy. The dynamic force signals are found reasonably sensitive to simulate either the progressive or the random modes of tool edge deformation. While the frictional force components, feeding and radial, are found informative regarding progressive wear modes, the vertical (power) components is found more representative carrier to system instability resulting from the edge-s random deformation.
Abstract: A study of electromagnetic flow meter is presented in the paper. Comparison has been made between the analytical and the numerical results by the use of FEM numerical analysis (Quick Field 5.6) for determining polarization voltage through the circle cross section of the polarization transducer. Exciting and geometrical parameters increasing its effectiveness has been examined. The aim is to obtain maximal output signal. The investigations include different variants of the magnetic flux density distribution around the tube: homogeneous field of magnitude Bm, linear distribution with maximal value Bm and trapezium distribution conserving the same exciting magnetic energy as the homogeneous field.
Abstract: According to the density of the chips, designers are
trying to put so any facilities of computational and storage on single
chips. Along with the complexity of computational and storage
circuits, the designing, testing and debugging become more and more
complex and expensive. So, hardware design will be built by using
very high speed hardware description language, which is more
efficient and cost effective. This paper will focus on the
implementation of 32-bit ALU design based on Verilog hardware
description language. Adder and subtracter operate correctly on both
unsigned and positive numbers. In ALU, addition takes most of the
time if it uses the ripple-carry adder. The general strategy for
designing fast adders is to reduce the time required to form carry
signals. Adders that use this principle are called carry look- ahead
adder. The carry look-ahead adder is to be designed with combination
of 4-bit adders. The syntax of Verilog HDL is similar to the C
programming language. This paper proposes a unified approach to
ALU design in which both simulation and formal verification can
co-exist.
Abstract: This paper proposes a method to vibration analysis in
order to on-line monitoring and predictive maintenance during the
milling process. Adapting envelope method to diagnostics and the
analysis for milling tool materials is an important contribution to the
qualitative and quantitative characterization of milling capacity and a
step by modeling the three-dimensional cutting process. An
experimental protocol was designed and developed for the
acquisition, processing and analyzing three-dimensional signal. The
vibration envelope analysis is proposed to detect the cutting capacity
of the tool with the optimization application of cutting parameters.
The research is focused on Hilbert transform optimization to evaluate
the dynamic behavior of the machine/ tool/workpiece.
Abstract: The paper presents frame and burst acquisition in a satellite communication network based on time division multiple access (TDMA) in which the transmissions may be carried on different transponders. A unique word pattern is used for the acquisition process. The search for the frame is aided by soft-decision of QPSK modulated signals in an additive white Gaussian channel. Results show that when the false alarm rate is low the probability of detection is also low, and the acquisition time is long. Conversely when the false alarm rate is high, the probability of detection is also high and the acquisition time is short. Thus the system operators can trade high false alarm rates for high detection probabilities and shorter acquisition times.
Abstract: In a wind power generator using doubly fed induction
generator (DFIG), the three-phase pulse width modulation (PWM)
voltage source converter (VSC) is used as grid side converter (GSC)
and rotor side converter (RSC). The standard linear control laws
proposed for GSC provides not only instablity against comparatively
large-signal disturbances, but also the problem of stability due to
uncertainty of load and variations in parameters. In this paper, a
nonlinear controller is designed for grid side converter (GSC) of a
DFIG for wind power application. The nonlinear controller is
designed based on the input-output feedback linearization control
method. The resulting closed-loop system ensures a sufficient
stability region, make robust to variations in circuit parameters and
also exhibits good transient response. Computer simulations and
experimental results are presented to confirm the effectiveness of the
proposed control strategy.
Abstract: For gamma radiation detection, assemblies having
scintillation crystals and a photomultiplier tube, also there is a
preamplifier connected to the detector because the signals from
photomultiplier tube are of small amplitude. After pre-amplification
the signals are sent to the amplifier and then to the multichannel
analyser. The multichannel analyser sorts all incoming electrical
signals according to their amplitudes and sorts the detected photons
in channels covering small energy intervals. The energy range of
each channel depends on the gain settings of the multichannel
analyser and the high voltage across the photomultiplier tube. The
exit spectrum data of the two main isotopes studied ,putting data in
biomass program ,process it by Matlab program to get the solid
holdup image (solid spherical nuclear fuel)
Abstract: An implementation of current-mode multiphase sinusoidal oscillators is presented. Using CFTA-based lossy integrators, odd and odd/even phase systems can be realized with following advantages. The condition of oscillation and frequency of oscillation can be orthogonally tuned. The high output impedances facilitate easy driving an external load without additional current buffers. The proposed MSOs provide odd or even phase signals that are equally spaced in phase and equal amplitude. The circuit requires one CFTA, one resistor and one grounded capacitor per phase without additional current amplifier. The results of PSPICE simulations using CMOS CFTA are included to verify theory.
Abstract: The customary practice of identifying industrial sickness is a set traditional techniques which rely upon a range of manual monitoring and compilation of financial records. It makes the process tedious, time consuming and often are susceptible to manipulation. Therefore, certain readily available tools are required which can deal with such uncertain situations arising out of industrial sickness. It is more significant for a country like India where the fruits of development are rarely equally distributed. In this paper, we propose an approach based on Artificial Neural Network (ANN) to deal with industrial sickness with specific focus on a few such units taken from a less developed north-east (NE) Indian state like Assam. The proposed system provides decision regarding industrial sickness using eight different parameters which are directly related to the stages of sickness of such units. The mechanism primarily uses certain signals and symptoms of industrial health to decide upon the state of a unit. Specifically, we formulate an ANN based block with data obtained from a few selected units of Assam so that required decisions related to industrial health could be taken. The system thus formulated could become an important part of planning and development. It can also contribute towards computerization of decision support systems related to industrial health and help in better management.
Abstract: A new voltage-mode triple-input single-output multifunction filter using only two current conveyors is presented. The proposed filter which possesses three inputs and single-output can generate all biquadratic filtering functions at the output terminal by selecting different input signal combinations. The validity of the proposed filter is verified through PSPICE simulations.
Abstract: This paper presents a signal analysis process for
improving energy completeness based on the Hilbert-Huang
Transform (HHT). Firstly, the vibration signal of a DC Motor obtained
by employing an accelerometer is the model used to analyze the
signal. Secondly, the intrinsic mode functions (IMFs) and Hilbert
spectrum of the decomposed signal are obtained by applying HHT.
The results of the IMFs constituent and the original signal are
compared and the process of energy loss is discussed. Finally, the
differences between Wavelet Transform (WT) and HHT in analyzing
the signal are compared. The simulated results reveal the analysis
process based on HHT is advantageous for the enhancement of energy
completeness.
Abstract: In this paper we present an enhanced noise reduction method for robust speech recognition using Adaptive Gain Equalizer with Non linear Spectral Subtraction. In Adaptive Gain Equalizer method (AGE), the input signal is divided into a number of subbands that are individually weighed in time domain, in accordance to the short time Signal-to-Noise Ratio (SNR) in each subband estimation at every time instant. Instead of focusing on suppression the noise on speech enhancement is focused. When analysis was done under various noise conditions for speech recognition, it was found that Adaptive Gain Equalizer method algorithm has an obvious failing point for a SNR of -5 dB, with inadequate levels of noise suppression for SNR less than this point. This work proposes the implementation of AGE when coupled with Non linear Spectral Subtraction (AGE-NSS) for robust speech recognition. The experimental result shows that out AGE-NSS performs the AGE when SNR drops below -5db level.
Abstract: Three new algorithms based on minimization of autocorrelation of transmitted symbols and the SLM approach which are computationally less demanding have been proposed. In the first algorithm, autocorrelation of complex data sequence is minimized to a value of 1 that results in reduction of PAPR. Second algorithm generates multiple random sequences from the sequence generated in the first algorithm with same value of autocorrelation i.e. 1. Out of these, the sequence with minimum PAPR is transmitted. Third algorithm is an extension of the second algorithm and requires minimum side information to be transmitted. Multiple sequences are generated by modifying a fixed number of complex numbers in an OFDM data sequence using only one factor. The multiple sequences represent the same data sequence and the one giving minimum PAPR is transmitted. Simulation results for a 256 subcarrier OFDM system show that significant reduction in PAPR is achieved using the proposed algorithms.