Abstract: Providing authentication for the messages exchanged
between group members in addition to confidentiality is an important
issue in Secure Group communication. We develop a protocol for
Secure Authentic Communication where we address authentication
for the group communication scheme proposed by Blundo et al.
which only provides confidentiality. Authentication scheme used is a
multiparty authentication scheme which allows all the users in the
system to send and receive messages simultaneously. Our scheme is
secure against colluding malicious parties numbering fewer than k.
Abstract: The motion planning technique described in this paper has been developed to eliminate or reduce the residual vibrations of belt-driven rotary platforms, while maintaining unchanged the motion time and the total angular displacement of the platform. The proposed approach is based on a suitable choice of the motion command given to the servomotor that drives the mechanical device; this command is defined by some numerical coefficients which determine the shape of the displacement, velocity and acceleration profiles. Using a numerical optimization technique, these coefficients can be changed without altering the continuity conditions imposed on the displacement and its time derivatives at the initial and final time instants. The proposed technique can be easily and quickly implemented on an actual device, since it requires only a simple modification of the motion command profile mapped in the memory of the electronic motion controller.
Abstract: The aim of this study was to test whether the Attention
Networks Test (ANT) showed temporal decrements in performance.
Vigilance tasks typically show such decrements, which may reflect
impairments in executive control resulting from cognitive fatigue.
The ANT assesses executive control, as well as alerting and
orienting. Thus, it was hypothesized that ANT executive control
would deteriorate over time. Manipulations including task condition
(trial composition) and masking were included in the experimental
design in an attempt to increase performance decrements. However,
results showed that there is no temporal decrement on the ANT. The
roles of task demands, cognitive fatigue and participant motivation in
producing this result are discussed. The ANT may not be an effective
tool for investigating temporal decrement in attention.
Abstract: It is well known that metallic particles reduce the
reliability of Gas-Insulated Substation (GIS) equipments by initiating
partial discharge (PDs) that can lead to breakdown and complete
failure of GIS. This paper investigates the characteristics of PDs
caused by metallic particle adhering to the solid spacer. The PD
detection and measurement were carried out by using IEC 60270
method with particles of different sizes and at different positions on
the spacer surface. The results show that a particle of certain size at
certain position possesses a unique PD characteristic as compared to
those caused by particles of different sizes and/or at different
positions. Therefore PD characteristics may be useful for the particle
size and position identification.
Abstract: Today technological process makes possible surface
control of producing parts which is needful for product quality
guarantee. Geometrical structure of part surface includes form,
proportion, accuracy to shape, accuracy to size, alignment and
surface topography (roughness, waviness, etc.). All these parameters
are dependence at technology, production machine parameters,
material properties, but also at human, etc. Every parameters
approves at total part accuracy, it is means at accuracy to shape. One
of the most important accuracy to shape element is roundness. This
paper will be deals by comparison of roughness deviations at
coordination measuring machines and at special single purpose
machines. Will describing measuring by discreet method
(discontinuous) and scanning method (continuous) at coordination
measuring machines and confrontation with reference method using
at single purpose machines.
Abstract: The Pads have unique values of thermophysical
properties (THP) having important contribution over heat transfer
into the PCB structure.
Materials with high thermal diffusivity (TD) rapidly adjust their
temperature to that of their surroundings, because the HT is quick in
compare to their volumetric heat capacity (VHC).
In the paper is presenting the diffusivity tests (ASTM E1461 flash
method) for PCBs with different core materials. In the experiments,
the multilayer structure of PCBA was taken into consideration, an
equivalent property referring to each of experimental structure be
practically measured.
Concerning to entire structure, the THP emphasize the major
contribution of substrate in establishing of reflow soldering process
(RSP) heat transfer necessities. This conclusion offer practical
solution for heat transfer time constant calculation as function of
thickness and substrate material diffusivity with an acceptable error
estimation.
Abstract: Adapting wireless devices to communicate within grid
networks empowers us by providing range of possibilities.. These
devices create a mechanism for consumers and publishers to create
modern networks with or without peer device utilization. Emerging
mobile networks creates new challenges in the areas of reliability,
security, and adaptability. In this paper, we propose a system
encompassing mobility management using AAA context transfer for
mobile grid networks. This system ultimately results in seamless task
processing and reduced packet loss, communication delays,
bandwidth, and errors.
Abstract: We introduce an extended resource leveling model that abstracts real life projects that consider specific work ranges for each resource. Contrary to traditional resource leveling problems this model considers scarce resources and multiple objectives: the minimization of the project makespan and the leveling of each resource usage over time. We formulate this model as a multiobjective optimization problem and we propose a multiobjective genetic algorithm-based solver to optimize it. This solver consists in a two-stage process: a main stage where we obtain non-dominated solutions for all the objectives, and a postprocessing stage where we seek to specifically improve the resource leveling of these solutions. We propose an intelligent encoding for the solver that allows including domain specific knowledge in the solving mechanism. The chosen encoding proves to be effective to solve leveling problems with scarce resources and multiple objectives. The outcome of the proposed solvers represent optimized trade-offs (alternatives) that can be later evaluated by a decision maker, this multi-solution approach represents an advantage over the traditional single solution approach. We compare the proposed solver with state-of-art resource leveling methods and we report competitive and performing results.
Abstract: The OTOP Entrepreneurship that used to create
substantial source of income for local Thai communities are now in a
stage of exigent matters that required assistances from public sectors
due to over Entrepreneurship of duplicative ideas, unable to adjust
costs and prices, lack of innovation, and inadequate of quality
control. Moreover, there is a repetitive problem of middlemen who
constantly corner the OTOP market. Local OTOP producers become
easy preys since they do not know how to add more values, how to
create and maintain their own brand name, and how to create proper
packaging and labeling. The suggested solutions to local OTOP
producers are to adopt modern management techniques, to find
knowhow to add more values to products and to unravel other
marketing problems. The objectives of this research are to study the
prevalent OTOP products management and to discover direction to
manage OTOP products to enhance the effectiveness of OTOP
Entrepreneurship in Nonthaburi Province, Thailand. There were 113
participants in this study. The research tools can be divided into two
parts: First part is done by questionnaire to find responses of the
prevalent OTOP Entrepreneurship management. Second part is the
use of focus group which is conducted to encapsulate ideas and local
wisdom. Data analysis is performed by using frequency, percentage,
mean, and standard deviation as well as the synthesis of several small
group discussions. The findings reveal that 1) Business Resources:
the quality of product is most important and the marketing of product
is least important. 2) Business Management: Leadership is most
important and raw material planning is least important. 3) Business
Readiness: Communication is most important and packaging is least
important. 4) Support from public sector: Certified from the
government is most important and source of raw material is the least
important.
Abstract: This paper presents an automated inspection algorithm
for a thick plate. Thick plates typically have various types of surface
defects, such as scabs, scratches, and roller marks. These defects have
individual characteristics including brightness and shape. Therefore, it
is not simple to detect all the defects. In order to solve these problems
and to detect defects more effectively, we propose a dual light
switching lighting method and a defect detection algorithm based on
Gabor filters.
Abstract: In this paper a computer system for electromagnetic
properties measurements is designed. The system employs Agilent
4294A precision impedance analyzer to measure the amplitude and
the phase of a signal applied over a tested biological tissue sample.
Measured by the developed computer system data could be used for
tissue characterization in wide frequency range from 40Hz to
110MHz. The computer system can interface with output devices
acquiring flexible testing process.
Abstract: This paper is devoted to predict laminar and turbulent
heating rates around blunt re-entry spacecraft at hypersonic
conditions. Heating calculation of a hypersonic body is normally
performed during the critical part of its flight trajectory. The
procedure is of an inverse method, where a shock wave is assumed,
and the body shape that supports this shock, as well as the flowfield
between the shock and body, are calculated. For simplicity the
normal momentum equation is replaced with a second order pressure
relation; this simplification significantly reduces computation time.
The geometries specified in this research, are parabola and ellipsoids
which may have conical after bodies. An excellent agreement is
observed between the results obtained in this paper and those
calculated by others- research. Since this method is much faster than
Navier-Stokes solutions, it can be used in preliminary design,
parametric study of hypersonic vehicles.
Abstract: Development of a Robust Supply Chain for Dynamic
Operating Environment as we move further into the twenty first
century, organisations are under increasing pressure to deliver a high
product variation at a reasonable cost without compromise in quality.
In a number of cases this will take the form of a customised or high
variety low volume manufacturing system that requires prudent
management of resources, among a number of functions, to achieve
competitive advantage. Purchasing and Supply Chain management is
one of such function and due to the substantial interaction with
external elements needs to be strategically managed. This requires a
number of primary and supporting tools that will enable the
appropriate decisions to be made rapidly. This capability is
especially vital in a dynamic environment as it provides a pivotal role
in increasing the profit margin of the product. The management of
this function can be challenging by itself and even more for Small
and Medium Enterprises (SMEs) due to the limited resources and
expertise available at their disposal.
This paper discusses the development of tools and concepts
towards effectively managing the purchasing and supply chain
function. The developed tools and concepts will provide a cost
effective way of managing this function within SMEs. The paper
further shows the use of these tools within Contechs, a manufacturer
of luxury boat interiors, and the associated benefits achieved as a
result of this implementation. Finally a generic framework towards
use in such environments is presented.
Abstract: Directive 2009/28/CE establishes, as obligatory objective, a share of renewable energies on energetic consumption of 20%, in European Union, in 2020 However, such European normative gives freedom to member states in the selection of the renewable promotion mechanism that allows them to obtain that objective. In this paper, we analyze the main characteristics of the promotion mechanisms of renewable energy used in the countries that shape the Electricity Iberian Market (Spain and Portugal) and the results in employment. The importance of these countries is given by the great increasing of the renewable energies which suppose a share higher than 30% of the overall generation in 2010. Therefore, this research paper can serve as the basis for the learning of other countries with regard to the main advantages that entail the use of a feed-in tariff system.
Abstract: This paper describes a computer model of Quantum Field Theory (QFT), referred to in this paper as QTModel. After specifying the initial configuration for a QFT process (e.g. scattering) the model generates the possible applicable processes in terms of Feynman diagrams, the equations for the scattering matrix, and evaluates probability amplitudes for the scattering matrix and cross sections. The computations of probability amplitudes are performed numerically. The equations generated by QTModel are provided for demonstration purposes only. They are not directly used as the base for the computations of probability amplitudes. The computer model supports two modes for the computation of the probability amplitudes: (1) computation according to standard QFT, and (2) computation according to a proposed functional interpretation of quantum theory.
Abstract: This paper proposes and implements an core transform architecture, which is one of the major processes in HEVC video compression standard. The proposed core transform architecture is implemented with only adders and shifters instead of area-consuming multipliers. Shifters in the proposed core transform architecture are implemented in wires and multiplexers, which significantly reduces chip area. Also, it can process from 4×4 to 16×16 blocks with common hardware by reusing processing elements. Designed core transform architecture in 0.13um technology can process a 16×16 block with 2-D transform in 130 cycles, and its gate count is 101,015 gates.
Abstract: Combined conduction-free convection heat transfer in
vertical eccentric annuli is numerically investigated using a finitedifference
technique. Numerical results, representing the heat transfer
parameters such as annulus walls temperature, heat flux, and heat
absorbed in the developing region of the annulus, are presented for a
Newtonian fluid of Prandtl number 0.7, fluid-annulus radius ratio 0.5,
solid-fluid thermal conductivity ratio 10, inner and outer wall
dimensionless thicknesses 0.1 and 0.2, respectively, and
dimensionless eccentricities 0.1, 0.3, 0.5, and 0.7. The annulus walls
are subjected to thermal boundary conditions, which are obtained by
heating one wall isothermally whereas keeping the other wall at inlet
fluid temperature. In the present paper, the annulus heights required
to achieve thermal full development for prescribed eccentricities are
obtained. Furthermore, the variation in the height of thermal full
development as function of the geometrical parameter, i.e.,
eccentricity is also investigated.
Abstract: This study develops a relation to explore the factors influencing management and technology capabilities in strategic alliances. Alliances between firms are recognizing increasingly popular as a vehicle to create and extract greater value from the market. Firm’s alliance can be described as the collaborative problem solving process to solve problems jointly. This study starts from research questions what factors of firm’s management and technology characteristics affect performance of firms which are formed alliances. In this study, we investigated the effect of strategic alliances on company performance. That is, we try to identify whether firms made an alliance with other organizations are differed by characteristics of management and technology. And we test that alliance type and alliance experiences moderate the relationship between firm’s capabilities and its performance. We employ problem-solving perspective and resource-based view perspective to shed light on this research questions. The empirical work is based on the Survey of Business Activities conducted from2006 to 2008 by Statistics Korea. We verify correlations between to point out that these results contribute new empirical evidence on the effect of strategic alliances on company performance.
Abstract: There are several ways of improving the performance of a vapor compression refrigeration cycle. Use of an ejector as expansion device is one of the alternative ways. The present paper aims at evaluate the performance improvement of a vapor compression refrigeration cycle under a wide range of operating conditions. A numerical model is developed and a parametric study of important parameters such as condensation (30-50°C) and evaporation temperatures (-20-5°C), nozzle and diffuser efficiencies (0.75-0.95), subcooling and superheating degrees (0-15K) are investigated. The model verification gives a good agreement with the literature data. The simulation results revealed that condensation temperature has the highest effect (129%) on the performance improvement ratio while superheating has the lowest one (6.2%). Among ejector efficiencies, the diffuser efficiency has a significant effect on the COP of ejector expansion refrigeration cycle. The COP improvement percentage decreases from 10.9% to 4.6% as subcooling degrees increases by 15K.
Abstract: Ant colony optimization is an ant algorithm framework that took inspiration from foraging behavior of ant colonies. Indeed, ACO algorithms use a chemical communication, represented by pheromone trails, to build good solutions. However, ants involve different communication channels to interact. Thus, this paper introduces the acoustic communication between ants while they are foraging. This process allows fine and local exploration of search space and permits optimal solution to be improved.