Abstract: The aim of this study was to extract sugar from
sugarcane using high electric field pulse (HELP) as a non-thermal cell permeabilization method. The result of this study showed that it
is possible to permeablize sugar cane cells using HELP at very short times (less than 10 sec.) and at room temperature. Increasing the field strength (from 0.5kV/cm to 2kV/cm) and pulse number (1 to 12) led to increasing the permeabilization of sugar cane cells. The energy
consumption during HELP treatment of sugar cane (2.4 kJ/kg) was about 100 times less compared to thermal cell disintegration at 85
Abstract: Predictions of flow and heat transfer characteristics and shape optimization in internally finned circular tubes have been performed on three-dimensional periodically fully developed turbulent flow and thermal fields. For a trapezoidal fin profile, the effects of fin height h, upper fin widths d1, lower fin widths d2, and helix angle of fin ? on transport phenomena are investigated for the condition of fin number of N = 30. The CFD and mathematical optimization technique are coupled in order to optimize the shape of internally finned tube. The optimal solutions of the design variables (i.e., upper and lower fin widths, fin height and helix angle) are numerically obtained by minimizing the pressure loss and maximizing the heat transfer rate, simultaneously, for the limiting conditions of d1 = 0.5~1.5 mm, d2 = 0.5~1.5 mm, h= 0.5~1.5mm, ? = 10~30 degrees. The fully developed flow and thermal fields are predicted using the finite volume method and the optimization is carried out by means of the multi-objective genetic algorithm that is widely used in the constrained nonlinear optimization problem.
Abstract: Turbine blade cooling is considered as the most
effective way of maintaining high operating temperature making use
of the available materials, and turbine systems with wet compression
have a potential for future power generation because of high efficiency
and high specific power with a relatively low cost. In this paper
performance analysis of wet-compression gas turbine cycle with
turbine blade cooling is carried out. The wet compression process is
analytically modeled based on non-equilibrium droplet evaporation.
Special attention is paid for the effects of pressure ratio and water
injection ratio on the important system variables such as ratio of
coolant fluid flow, fuel consumption, thermal efficiency and specific
power. Parametric studies show that wet compression leads to
insignificant improvement in thermal efficiency but significant
enhancement of specific power in gas turbine systems with turbine
blade cooling.
Abstract: Nowadays, desalination of salt water is considered an important industrial process. In many parts of the world, particularly in the gulf countries, the multi-stage flash (MSF) water desalination has an essential contribution in the production of fresh water. In this study, a simple mathematical model is defined to design a MSF desalination system and the feasibility of using the MSF desalination process in proximity of a 42 MW power plant is investigated. This power plant can just provide 10 ton/h superheated steam from low pressure (LP) section of heat recovery steam generator (HRSG) for thermal desalting system. The designed MSF system with gained output ratio (GOR) of 10.3 has 24 flashing stages and can produce 2480 ton/d of fresh water. The expected performance characteristics of the designed MSF desalination plant are determined. In addition, the effect of motive water pressure on the amount of non-condensable gases removed by water jet vacuum pumps is investigated.
Abstract: The application of agro-industrial waste in Aluminum
Metal Matrix Composites has been getting more attention as they
can reinforce particles in metal matrix which enhance the strength
properties of the composites. In addition, by applying these agroindustrial
wastes in useful way not only save the manufacturing cost
of products but also reduce the pollutions on environment. This
paper represents a literature review on a range of industrial wastes
and their utilization in metal matrix composites. The paper describes
the synthesis methods of agro-industrial waste filled metal matrix
composite materials and their mechanical, wear, corrosion, and
physical properties. It also highlights the current application and
future potential of agro-industrial waste reinforced composites in
aerospace, automotive and other construction industries.
Abstract: According to the Auckland climate, building passive
design more focus on improving winter indoor thermal and health
conditions. Based on field study data of indoor air temperature and
relative humidity close to ceiling and floor of an insulated Auckland
townhouse with and without a whole home mechanical ventilation
system, this study is to analysis variation of indoor microclimate data
of an Auckland townhouse using or not using the mechanical
ventilation system to evaluate winter indoor thermal and health
conditions for the future house design with a mechanical ventilation
system.
Abstract: This paper will first describe predictor controllers
when the proportional-integral-derivative (PID) controllers are
inactive for procedures that have large delay time (LDT) in transfer
stage. Therefore in those states, the predictor controllers are better
than the PID controllers, then compares three types of predictor
controllers. The value of these controller-s parameters are obtained
by trial and error method, so here an effort has been made to obtain
these parameters by Ziegler-Nichols method. Eventually in this paper
Ziegler-Nichols method has been described and finally, a PIP
controller has been designed for a thermal system, which circulates
hot air to keep the temperature of a chamber constant.
Abstract: The reliable results of an insulated oval duct
considering heat radiation are obtained basing on accurate oval
perimeter obtained by integral method as well as one-dimensional
Plane Wedge Thermal Resistance (PWTR) model. This is an extension
study of former paper of insulated oval duct neglecting heat radiation.
It is found that in the practical situations with long-short-axes ratio a/b
4.5% while t/R2
Abstract: Water vapour transport properties of gypsum block
are studied in dependence on relative humidity using inverse analysis
based on genetic algorithm. The computational inverse analysis is
performed for the relative humidity profiles measured along the
longitudinal axis of a rod sample. Within the performed transient
experiment, the studied sample is exposed to two environments with
different relative humidity, whereas the temperature is kept constant.
For the basic gypsum characterisation and for the assessment of input
material parameters necessary for computational application of
genetic algorithm, the basic material properties of gypsum are
measured as well as its thermal and water vapour storage parameters.
On the basis of application of genetic algorithm, the relative
humidity dependent water vapour diffusion coefficient and water
vapour diffusion resistance factor are calculated.
Abstract: This paper presents an efficient emission constrained
economic dispatch algorithm that deals with nonlinear cost function
and constraints. It is then incorporated into the dynamic
programming based hydrothermal coordination program. The
program has been tested on a practical utility system having 32
thermal and 12 hydro generating units. Test results show that a slight
increase in production cost causes a substantial reduction in
emission.
Abstract: Although face recognition seems as an easy task for
human, automatic face recognition is a much more challenging task
due to variations in time, illumination and pose. In this paper, the
influence of time-lapse on visible and thermal images is examined.
Orthogonal moment invariants are used as a feature extractor to
analyze the effect of time-lapse on thermal and visible images and the
results are compared with conventional Principal Component
Analysis (PCA). A new triangle square ratio criterion is employed
instead of Euclidean distance to enhance the performance of nearest
neighbor classifier. The results of this study indicate that the ideal
feature vectors can be represented with high discrimination power
due to the global characteristic of orthogonal moment invariants.
Moreover, the effect of time-lapse has been decreasing and enhancing
the accuracy of face recognition considerably in comparison with
PCA. Furthermore, our experimental results based on moment
invariant and triangle square ratio criterion show that the proposed
approach achieves on average 13.6% higher in recognition rate than
PCA.
Abstract: The two-phase flow field and the motion of the free
surface in an oscillating channel are simulated numerically to assess
the methodology for simulating nuclear reacotr thermal hydraulics
under seismic conditions. Two numerical methods are compared: one
is to model the oscillating channel directly using the moving grid of
the Arbitrary Lagrangian-Eulerian method, and the other is to simulate
the effect of channel motion using the oscillating acceleration acting
on the fluid in the stationary channel. The two-phase flow field in the
oscillating channel is simulated using the level set method in both
cases. The calculated results using the oscillating acceleration are
found to coinside with those using the moving grid, and the theoretical
back ground and the limitation of oscillating acceleration are discussed.
It is shown that the change in the interfacial area between liquid and
gas phases under seismic conditions is important for nuclear reactor
thermal hydraulics.
Abstract: Experiments were carried out to evaluate the
influence of the addition of hydrogen to the inlet air on the
performance of a single cylinder direct injection diesel engine.
Hydrogen was injected in the inlet manifold. The addition of
hydrogen was done on energy replacement basis. It was found that
the addition of hydrogen improves the combustion process due to
superior combustion characteristics of hydrogen in comparison to
conventional diesel fuels. It was also found that 10% energy
replacement improves the engine thermal efficiency by about 40%
and reduces the sfc by about 35% however the volumetric efficiency
was reduced by about 35%.
Abstract: Experiments have been carried out at the Latvia
University of Agriculture Department of Food Technology. The aim
of this work was to assess the effect of thermal treatment in flexible
retort pouch packaging on the quality of potatoes’ produce during the
storage time. Samples were evaluated immediately after retort
thermal treatment; and following 1; 2; 3 and 4 storage months at the
ambient temperature of +18±2ºC in vacuum packaging from
polyamide/polyethylene (PA/PE) and aluminum/polyethylene
(Al/PE) film pouches with barrier properties. Experimentally the
quality of the potatoes’ produce in dry butter and mushroom
dressings was characterized by measuring pH, hardness, color,
microbiological properties and sensory evaluation. The sterilization
was effective in protecting the produce from physical, chemical, and
microbial quality degradation. According to the study of obtained
data, it can be argued that the selected product processing technology
and packaging materials could be applied to provide the safety and
security during four-month storage period.
Abstract: This study describes a capillary-based device
integrated with the heating and cooling modules for polymerase chain
reaction (PCR). The device consists of the reaction
polytetrafluoroethylene (PTFE) capillary, the aluminum blocks, and is
equipped with two cartridge heaters, a thermoelectric (TE) cooler, a
fan, and some thermocouples for temperature control. The cartridge
heaters are placed into the heating blocks and maintained at two
different temperatures to achieve the denaturation and the extension
step. Some thermocouples inserted into the capillary are used to obtain
the transient temperature profiles of the reaction sample during
thermal cycles. A 483-bp DNA template is amplified successfully in
the designed system and the traditional thermal cycler. This work
should be interesting to persons involved in the high-temperature
based reactions and genomics or cell analysis.
Abstract: The paper provides a numerical investigation of the
entropy generation analysis due to natural convection in an inclined
square porous cavity. The coupled equations of mass, momentum,
energy and species conservation are solved using the Control Volume
Finite-Element Method. Effect of medium permeability and
inclination angle on entropy generation is analysed. It was found that
according to the Darcy number and the porous thermal Raleigh
number values, the entropy generation could be mainly due to heat
transfer or to fluid friction irreversibility and that entropy generation
reaches extremum values for specific inclination angles.
Abstract: Temperature, relative humidity and overhygroscopic
moisture fields in a sandstone wall provided with interior thermal
insulation were calculated in order to assess the hygric performance
of the retrofitted wall. Computational simulations showed that during
the time period of 10 years which was subject of investigation no
overhygroscopic moisture appeared in the analyzed building
envelope so that it performed in a satisfactory way from the hygric
point of view.
Abstract: Electrochemical-oxidation of Reactive Black-5 (RB- 5) was conducted for degradation using DSA type Ti/RuO2-SnO2- Sb2O5 electrode. In the study, for electro-oxidation, electrode was indigenously fabricated in laboratory using titanium as substrate. This substrate was coated using different metal oxides RuO2, Sb2O5 and SnO2 by thermal decomposition method. Laboratory scale batch reactor was used for degradation and decolorization studies at pH 2, 7 and 11. Current density (50mA/cm2) and distance between electrodes (8mm) were kept constant for all experiments. Under identical conditions, removal of color, COD and TOC at initial pH 2 was 99.40%, 55% and 37% respectively for initial concentration of 100 mg/L RB-5. Surface morphology and composition of the fabricated electrode coatings were characterized using scanning electron microscopy (SEM) and energy dispersive X-ray spectroscopy (EDX) respectively. Coating microstructure was analyzed by X-ray diffraction (XRD). Results of this study further revealed that almost 90% of oxidation occurred within 5-10 minutes.
Abstract: Solid oxide fuel cells have been considered in the last years as one of the most promising technologies for very highefficiency electric energy generation from hydrogen or other hydrocarbons, both with simple fuel cell plants and with integrated gas turbine-fuel cell systems. In the present study, a detailed thermodynamic analysis has been carried out. Mass and exergy balances are performed not only for the whole plant but also for each component in order to evaluate the thermal efficiency of combined cycle. Moreover, different sources of irreversibilities within the SOFC stack have been discussed and a parametric study conducted to evaluate the effect of temperature as well as pressure on SOFC irreversibilities and its performance. In this investigation methane and hydrogen have been used for fueling the SOFC stack and combustion chamber.
Abstract: The counter flow solar air heaters, with four
transverse fins and wire mesh layers are constructed and investigated
experimentally for thermal efficiency at a geographic location of
Cyprus in the city of Famagusta. The absorber plate is replaced by
sixteen steel wire mesh layers, 0.18 x 0.18cm in cross section
opening and a 0.02cm in diameter. The wire mesh layers arranged in
three groups, first and second include 6 layers, while the third include
4 layers. All layers fixed in the duct parallel to the glazing and each
group separated from the others by wood frame thickness of 0.5cm to
reduce the pressure drop. The transverse fins arranged in a way to
force the air to flow through the bed like eight letter path with flow
depth 3cm. The proposed design has increased the heat transfer rate,
but on other hand causes a high pressure drop. The obtained results
show that, for air mass flow rate range between 0.011-0.036kg/s, the
thermal efficiency increases with increasing the air mass flow. The
maximum efficiency obtained is 65.6% for the mass flow rate of
0.036kg/s. Moreover, the temperature difference between the outlet
flow and the ambient temperature, ΔT, reduces as the air mass flow
rate increase. The maximum difference between the outlet and
ambient temperature obtained was 43°C for double pass for minimum
mass flow rate of 0.011kg/s. Comparison with a conventional solar
air heater collector shows a significantly development in the thermal
efficiency.