Abstract: The tubes in an Ammonia primary reformer furnace
operate close to the limits of materials technology in terms of the
stress induced as a result of very high temperatures, combined with
large differential pressures across the tube wall. Operation at tube
wall temperatures significantly above design can result in a rapid
increase in the number of tube failures, since tube life is very
sensitive to the absolute operating temperature of the tube. Clearly it
is important to measure tube wall temperatures accurately in order to
prevent premature tube failure by overheating.. In the present study,
the catalyst tubes in an Ammonia primary reformer has been modeled
taking into consideration heat, mass and momentum transfer as well
as reformer characteristics.. The investigations concern the effects of
tube characteristics and superficial tube wall temperatures on of the
percentage of heat flux, unconverted methane and production of
Hydrogen for various values of steam to carbon ratios. The results
show the impact of catalyst tubes length and diameters on the
performance of operating parameters in ammonia primary reformers.
Abstract: In this paper, a simple microfluidic device for monitoring algal cell behavior is proposed. An array of algal microwells is fabricated by PDMS soft-lithography using X-ray LIGA mold, placed on a glass substrate. Two layers of replicated PDMS and substrate are attached by oxygen plasma bonding, creating a microchannel for the microfluidic system. Algal cell are loaded into the microfluidic device, which provides positive charge on the bottom surface of wells. Algal cells, which are negative charged, can be attracted to the bottom of the wells via electrostatic interaction. By varying the concentration of algal cells in the loading suspension, it is possible to obtain wells with a single cell. Liquid medium for cells monitoring are flown continuously over the wells, providing nutrient and waste exchange between the well and the main flow. This device could lead to the uncovering of the quantitative biology of the algae, which is a key to effective and extensive algal utilizations in the field of biotechnology, food industry and bioenergy research and developments.
Abstract: In this study, a vibration analysis was carried out of
symmetric angle-ply laminated composite plates with and without
square hole when subjected to compressive loads, numerically. A
buckling analysis is also performed to determine the buckling load of
laminated plates. For each fibre orientation, the compression load is
taken equal to 50% of the corresponding buckling load. In the
analysis, finite element method (FEM) was applied to perform
parametric studies, the effects of degree of orthotropy and stacking
sequence upon the fundamental frequencies and buckling loads are
discussed. The results show that the presence of a constant
compressive load tends to reduce uniformly the natural frequencies
for materials which have a low degree of orthotropy. However, this
reduction becomes non-uniform for materials with a higher degree of
orthotropy.
Abstract: This paper discusses the approach of real-time
controlling of the energy management system using the data
acquisition tool of LabVIEW. The main idea of this inspiration was
to interface the Station (PC) with the system and publish the data on
internet using LabVIEW. In this venture, controlling and switching of
3 phase AC loads are effectively and efficiently done. The phases are
also sensed through devices. In case of any failure the attached
generator starts functioning automatically. The computer sends
command to the system and system respond to the request. The
modern feature is to access and control the system world-wide using
world wide web (internet). This controlling can be done at any time
from anywhere to effectively use the energy especially in developing
countries where energy management is a big problem. In this system
totally integrated devices are used to operate via remote location.
Abstract: In this paper we present a Feed-Foward Neural
Networks Autoregressive (FFNN-AR) model with genetic algorithms
training optimization in order to predict the gross domestic product
growth of six countries. Specifically we propose a kind of weighted
regression, which can be used for econometric purposes, where the
initial inputs are multiplied by the neural networks final optimum
weights from input-hidden layer of the training process. The
forecasts are compared with those of the ordinary autoregressive
model and we conclude that the proposed regression-s forecasting
results outperform significant those of autoregressive model.
Moreover this technique can be used in Autoregressive-Moving
Average models, with and without exogenous inputs, as also the
training process with genetics algorithms optimization can be
replaced by the error back-propagation algorithm.
Abstract: Gas flaring is one of the most GHG emitting sources in the oil and gas industries. It is also a major way for wasting such an energy that could be better utilized and even generates revenue. Minimize flaring is an effective approach for reducing GHG emissions and also conserving energy in flaring systems. Integrating waste and flared gases into the fuel gas networks (FGN) of refineries is an efficient tool. A fuel gas network collects fuel gases from various source streams and mixes them in an optimal manner, and supplies them to different fuel sinks such as furnaces, boilers, turbines, etc. In this article we use fuel gas network model proposed by Hasan et al. as a base model and modify some of its features and add constraints on emission pollution by gas flaring to reduce GHG emissions as possible. Results for a refinery case study showed that integration of flare gas stream with waste and natural gas streams to construct an optimal FGN can significantly reduce total annualized cost and flaring emissions.
Abstract: Embedding Sustainability in technological curricula has become a crucial factor for educating engineers with competences in sustainability. The Technical University of Catalonia UPC, in 2008, designed the Sustainable Technology Excellence Program STEP 2015 in order to assure a successful Sustainability Embedding. This Program takes advantage of the opportunity that the redesign of all Bachelor and Master Degrees in Spain by 2010 under the European Higher Education Area framework offered. The STEP program goals are: to design compulsory courses in each degree; to develop the conceptual base and identify reference models in sustainability for all specialties at UPC; to create an internal interdisciplinary network of faculty from all the schools; to initiate new transdisciplinary research activities in technology-sustainability-education; to spread the know/how attained; to achieve international scientific excellence in technology-sustainability-education and to graduate the first engineers/architects of the new EHEA bachelors with sustainability as a generic competence. Specifically, in this paper authors explain their experience in leading the STEP program, and two examples are presented: Industrial Robotics subject and the curriculum for the School of Architecture.
Abstract: In this research, a systematic investigation was carried out to determine the optimum conditions of HDS reactor. Moreover, a suitable model was developed for a rigorous RTO (real time optimization) loop of HDS (Hydro desulfurization) process. A systematic experimental series was designed based on CCD (Central Composite design) and carried out in the related pilot plant to tune the develop model. The designed variables in the experiments were Temperature, LHSV and pressure. However, the hydrogen over fresh feed ratio was remained constant. The ranges of these variables were respectively equal to 320-380ºC, 1- 21/hr and 50-55 bar. a power law kinetic model was also developed for our further research in the future .The rate order and activation energy , power of reactant concentration and frequency factor of this model was respectively equal to 1.4, 92.66 kJ/mol and k0=2.7*109 .
Abstract: Many real-world data sets consist of a very high dimensional feature space. Most clustering techniques use the distance or similarity between objects as a measure to build clusters. But in high dimensional spaces, distances between points become relatively uniform. In such cases, density based approaches may give better results. Subspace Clustering algorithms automatically identify lower dimensional subspaces of the higher dimensional feature space in which clusters exist. In this paper, we propose a new clustering algorithm, ISC – Intelligent Subspace Clustering, which tries to overcome three major limitations of the existing state-of-art techniques. ISC determines the input parameter such as є – distance at various levels of Subspace Clustering which helps in finding meaningful clusters. The uniform parameters approach is not suitable for different kind of databases. ISC implements dynamic and adaptive determination of Meaningful clustering parameters based on hierarchical filtering approach. Third and most important feature of ISC is the ability of incremental learning and dynamic inclusion and exclusions of subspaces which lead to better cluster formation.
Abstract: The noteworthy point in the advancement of Brain Machine Interface (BMI) research is the ability to accurately extract features of the brain signals and to classify them into targeted control action with the easiest procedures since the expected beneficiaries are of disabled. In this paper, a new feature extraction method using the combination of adaptive band pass filters and adaptive autoregressive (AAR) modelling is proposed and applied to the classification of right and left motor imagery signals extracted from the brain. The introduction of the adaptive bandpass filter improves the characterization process of the autocorrelation functions of the AAR models, as it enhances and strengthens the EEG signal, which is noisy and stochastic in nature. The experimental results on the Graz BCI data set have shown that by implementing the proposed feature extraction method, a LDA and SVM classifier outperforms other AAR approaches of the BCI 2003 competition in terms of the mutual information, the competition criterion, or misclassification rate.
Abstract: The new architecture for quantum cellular
automata is offered. A QCA cell includes two layers nc-Si,
divided by a dielectric. Among themselves cells are connected
by the bridge from a conductive material. The comparison is
made between this and QCA, offered earlier by C. Lent's
group.
Abstract: The paper deals with the possibilities of modelling
vapour propagation of explosive substances in the FLUENT
software. With regard to very low tensions of explosive substance
vapours the experiment has been verified as exemplified by
mononitrotoluene. Either constant or time variable meteorological
conditions have been used for calculation. Further, it has been
verified that the eluent source may be time-dependent and may reflect
a real situation or the liberation rate may be constant. The execution
of the experiment as well as evaluation were clear and it could also
be used for modelling vapour and aerosol propagation of selected
explosive substances in the atmospheric boundary layer.
Abstract: There is strong evidence that water channel proteins
'aquaporins (AQPs)' are central components in plant-water relations
as well as a number of other physiological parameters. We had
previously reported the isolation of 24 plasma membrane intrinsic
protein (PIP) type AQPs. However, the gene numbers in rice and the
polyploid nature of bread wheat indicated a high probability of
further genes in the latter. The present work focused on identification
of further AQP isoforms in bread wheat. With the use of altered
primer design, we identified five genes homologous, designated
PIP1;5b, PIP2;9b, TaPIP2;2, TaPIP2;2a, TaPIP2;2b. Sequence
alignments indicate PIP1;5b, PIP2;9b are likely to be homeologues of
two previously reported genes while the other three are new genes
and could be homeologs of each other. The results indicate further
AQP diversity in wheat and the sequence data will enable physical
mapping of these genes to identify their genomes as well as genetic to
determine their association with any quantitative trait loci (QTLs)
associated with plant-water relation such as salinity or drought
tolerance.
Abstract: Checkpointing is one of the commonly used techniques to provide fault-tolerance in distributed systems so that the system can operate even if one or more components have failed. However, mobile computing systems are constrained by low bandwidth, mobility, lack of stable storage, frequent disconnections and limited battery life. Hence, checkpointing protocols having lesser number of synchronization messages and fewer checkpoints are preferred in mobile environment. There are two different approaches, although not orthogonal, to checkpoint mobile computing systems namely, time-based and index-based. Our protocol is a fusion of these two approaches, though not first of its kind. In the present exposition, an index-based checkpointing protocol has been developed, which uses time to indirectly coordinate the creation of consistent global checkpoints for mobile computing systems. The proposed algorithm is non-blocking, adaptive, and does not use any control message. Compared to other contemporary checkpointing algorithms, it is computationally more efficient because it takes lesser number of checkpoints and does not need to compute dependency relationships. A brief account of important and relevant works in both the fields, time-based and index-based, has also been included in the presentation.
Abstract: In this paper we present our results on the performance analysis of a multi-product manufacturing line. We study the influence of external perturbations, intermediate buffer content and the number of manufacturing stages on the production tracking error of each machine in the multi-product line operated under a surplusbased production control policy. Starting by the analysis of a single machine with multiple production stages (one for each product type), we provide bounds on the production error of each stage. Then, we extend our analysis to a line of multi-stage machines, where similarly, bounds on each production tracking error for each product type, as well as buffer content are obtained. Details on performance of the closed-loop flow line model are illustrated in numerical simulations.
Abstract: Security management has changed from the
management of security equipments and useful interface to manager.
It analyzes the whole security conditions of network and preserves the
network services from attacks. Secure router technology has security
functions, such as intrusion detection, IPsec(IP Security) and access
control, are applied to legacy router for secure networking. It controls
an unauthorized router access and detects an illegal network intrusion.
This paper relates to a security engine management of router based on
a security policy, which is the definition of security function against a
network intrusion. This paper explains the security policy and designs
the structure of security engine management framework.
Abstract: This paper presents an analytical model to estimate
the cost of an optimized design of reinforced concrete isolated
footing base on structural safety. Flexural and optimized formulas for
square and rectangular footingare derived base on ACI building code
of design, material cost and optimization. The optimization
constraints consist of upper and lower limits of depth and area of
steel. Footing depth and area of reinforcing steel are to be minimized
to yield the optimal footing dimensions. Optimized footing materials
cost of concrete, reinforcing steel and formwork of the designed
sections are computed. Total cost factor TCF and other cost factors
are developed to generalize and simplify the calculations of footing
material cost. Numerical examples are presented to illustrate the
model capability of estimating the material cost of the footing for a
desired axial load.
Abstract: This paper describes a new algorithm of arrangement
in parallel, based on Odd-Even Mergesort, called division and
concurrent mixes. The main idea of the algorithm is to achieve that
each processor uses a sequential algorithm for ordering a part of the
vector, and after that, for making the processors work in pairs in
order to mix two of these sections ordered in a greater one, also
ordered; after several iterations, the vector will be completely
ordered. The paper describes the implementation of the new
algorithm on a Message Passing environment (such as MPI). Besides,
it compares the obtained experimental results with the quicksort
sequential algorithm and with the parallel implementations (also on
MPI) of the algorithms quicksort and bitonic sort. The comparison
has been realized in an 8 processors cluster under GNU/Linux which
is running on a unique PC processor.
Abstract: This paper introduces our first efforts of developing a
new team for RoboCup Middle Size Competition. In our robots we
have applied omni directional based mobile system with omnidirectional
vision system and fuzzy control algorithm to navigate
robots. The control architecture of MRL middle-size robots is a three
layered architecture, Planning, Sequencing, and Executing. It also
uses Blackboard system to achieve coordination among agents.
Moreover, the architecture should have minimum dependency on low
level structure and have a uniform protocol to interact with real
robot.
Abstract: Paper deals with environmental metrics and assessment systems devoted to Small and Medium Sized Enterprises. Authors are presenting proposed assessment model which has an ability to discover current environmental strengths and weaknesses of Small and Middle Sized Enterprise. Suggested model has also an ambition to become a Sustainability Decision Tool. Model is able to identify "best environmental devision" in the company, and to quantify how this decision contributed into overall environmental improvement. Authors understand environmental improvements as environmental innovations (product, process and organizational). Suggested model is based on its own concept; however, authors are also utilizing already existing environmental assessment tools.