Abstract: An experimental study of anaerobic treatment was performed by hybrid upflow anaerobic sludge blanket (HUASB) reactor to treat produced water (PW) of an onshore crude oil terminal (COD: 1597 mg/L, NH3-N: 14.7 mg/L, phenol: 13.8 mg/L, BOD5: 862 mg/L, sodium: 6240 mg/L and chloride 9530 mg/L). The produced water with high salinity and other toxic substances will inhibit the methanogens performance if there is no adaptation on biomass before anaerobic digestion. COD removal from produced water was investigated at five different dilutions of produced water and tap water (TW) without any nutrient addition and pre-treatment. The dilution ratios were 1PW:4TW, 2PW:3TW, 3PW:2TW, 4PW:1TW and 5PW:0TW. The reactor was evaluated at mesophilic operating condition (35 ± 2 °C) at 5 days of HRT for 250 days continuous feed. The average COD removals for 1PW:4TW, 2PW:3TW, 3PW:2TW, 4PW:1TW and 5PW:0TW were found to be approximately 76.1%, 73.8%, 70.3%, 46.3% and 61.82% respectively, with final average effluent COD of 123.7 mg/L, 240 mg/L, 294 mg/L, 589 mg/L and 738 mg/L, respectively.
Abstract: The computer modeling is carried out for parameter of
sensitivity of optoelectronic chemical and biosensors, using
phenomena of surface plasmon resonance (SPR). The physical model
of SPR-sensor-s is described with (or without) of modifications of
sensitive gold film surface by a dielectric layer. The variants of
increasing of sensitivity for SPR-biosensors, constructed on the
principle gold – dielectric – biomolecular layer are considered. Two
methods of mathematical treatment of SPR-curve are compared –
traditional, with estimation of sensor-s response as shift of the SPRcurve
minimum and proposed, for system with dielectric layer, using
calculating of the derivative in the point of SPR-curve half-width.
Abstract: The major goal in defining and examining game
scenarios is to find good strategies as solutions to the game. A
plausible solution is a recommendation to the players on how to play
the game, which is represented as strategies guided by the various
choices available to the players. These choices invariably compel the
players (decision makers) to execute an action following some
conscious tactics. In this paper, we proposed a refinement-based
heuristic as a machine learning technique for human-like decision
making in playing Ayo game. The result showed that our machine
learning technique is more adaptable and more responsive in making
decision than human intelligence. The technique has the advantage
that a search is astutely conducted in a shallow horizon game tree.
Our simulation was tested against Awale shareware and an appealing
result was obtained.
Abstract: The use of a Bayesian Hierarchical Model (BHM) to interpret breath measurements obtained during a 13C Octanoic Breath Test (13COBT) is demonstrated. The statistical analysis was implemented using WinBUGS, a commercially available computer package for Bayesian inference. A hierarchical setting was adopted where poorly defined parameters associated with a delayed Gastric Emptying (GE) were able to "borrow" strength from global distributions. This is proved to be a sufficient tool to correct model's failures and data inconsistencies apparent in conventional analyses employing a Non-linear least squares technique (NLS). Direct comparison of two parameters describing gastric emptying ng ( tlag -lag phase, t1/ 2 -half emptying time) revealed a strong correlation between the two methods. Despite our large dataset ( n = 164 ), Bayesian modeling was fast and provided a successful fitting for all subjects. On the contrary, NLS failed to return acceptable estimates in cases where GE was delayed.
Abstract: The paper presents an investigation into the role of virtual reality and web technologies in the field of distance education. Within this frame, special emphasis is given on the building of web-based virtual learning environments so as to successfully fulfill their educational objectives. In particular, basic pedagogical methods are studied, focusing mainly on the efficient preparation, approach and presentation of learning content, and specific designing rules are presented considering the hypermedia, virtual and educational nature of this kind of applications. The paper also aims to highlight the educational benefits arising from the use of virtual reality technology in medicine and study the emerging area of web-based medical simulations. Finally, an innovative virtual reality environment for distance education in medicine is demonstrated. The proposed environment reproduces conditions of the real learning process and enhances learning through a real-time interactive simulator.
Abstract: Segmentation techniques based on Active Contour
Models have been strongly benefited from the use of prior information
during their evolution. Shape prior information is captured from
a training set and is introduced in the optimization procedure to
restrict the evolution into allowable shapes. In this way, the evolution
converges onto regions even with weak boundaries. Although
significant effort has been devoted on different ways of capturing
and analyzing prior information, very little thought has been devoted
on the way of combining image information with prior information.
This paper focuses on a more natural way of incorporating the
prior information in the level set framework. For proof of concept
the method is applied on hippocampus segmentation in T1-MR
images. Hippocampus segmentation is a very challenging task, due
to the multivariate surrounding region and the missing boundary
with the neighboring amygdala, whose intensities are identical. The
proposed method, mimics the human segmentation way and thus
shows enhancements in the segmentation accuracy.
Abstract: Proper management of residues originated from
industrial activities is considered as one of the serious challenges
faced by industrial societies due to their potential hazards to the
environment. Common disposal methods for industrial solid wastes
(ISWs) encompass various combinations of solely management
options, i.e. recycling, incineration, composting, and sanitary
landfilling. Indeed, the procedure used to evaluate and nominate the
best practical methods should be based on environmental, technical,
economical, and social assessments. In this paper an environmentaltechnical
assessment model is developed using analytical network
process (ANP) to facilitate the decision making practice for ISWs
generated at Gilan province, Iran. Using the results of performed
surveys on industrial units located at Gilan, the various groups of
solid wastes in the research area were characterized, and four
different ISW management scenarios were studied. The evaluation
process was conducted using the above-mentioned model in the
Super Decisions software (version 2.0.8) environment. The results
indicates that the best ISW management scenario for Gilan province
is consist of recycling the metal industries residues, composting the
putrescible portion of ISWs, combustion of paper, wood, fabric and
polymeric wastes as well as energy extraction in the incineration
plant, and finally landfilling the rest of the waste stream in addition
with rejected materials from recycling and compost production plants
and ashes from the incineration unit.
Abstract: In this paper is presented a Geographic Information System (GIS) approach in order to qualify and monitor the broadband lines in efficient way. The methodology used for interpolation is the Delaunay Triangular Irregular Network (TIN). This method is applied for a case study in ISP Greece monitoring 120,000 broadband lines.
Abstract: In this paper, a new approach based on the extent of
friendship between the nodes is proposed which makes the nodes to
co-operate in an ad hoc environment. The extended DSR protocol is
tested under different scenarios by varying the number of malicious
nodes and node moving speed. It is also tested varying the number of
nodes in simulation used. The result indicates the achieved
throughput by extended DSR is greater than the standard DSR and
indicates the percentage of malicious drops over total drops are less
in the case of extended DSR than the standard DSR.
Abstract: Non-saturated soils that while saturation greatly
decrease their volume, have sudden settlement due to increasing
humidity, fracture and structural crack are called loess soils. Whereas
importance of civil projects including: dams, canals and
constructions bearing this type of soil and thereof problems, it is
required for carrying out more research and study in relation to loess
soils. This research studies shear strength parameters by using
grading test, Atterberg limit, compression, direct shear and
consolidation and then effect of using cement and lime additives on
stability of loess soils is studied. In related tests, lime and cement are
separately added to mixed ratios under different percentages of soil
and for different times the stabilized samples are processed and effect
of aforesaid additives on shear strength parameters of soil is studied.
Results show that upon passing time the effect of additives and
collapsible potential is greatly decreased and upon increasing
percentage of cement and lime the maximum dry density is
decreased; however, optimum humidity is increased. In addition,
liquid limit and plastic index is decreased; however, plastic index
limit is increased. It is to be noted that results of direct shear test
reveal increasing shear strength of soil due to increasing cohesion
parameter and soil friction angle.
Abstract: Octree compression techniques have been used
for several years for compressing large three dimensional data
sets into homogeneous regions. This compression technique
is ideally suited to datasets which have similar values in
clusters. Oil engineers represent reservoirs as a three dimensional
grid where hydrocarbons occur naturally in clusters. This
research looks at the efficiency of storing these grids using
octree compression techniques where grid cells are broken
into active and inactive regions. Initial experiments yielded
high compression ratios as only active leaf nodes and their
ancestor, header nodes are stored as a bitstream to file on
disk. Savings in computational time and memory were possible
at decompression, as only active leaf nodes are sent to the
graphics card eliminating the need of reconstructing the original
matrix. This results in a more compact vertex table, which can
be loaded into the graphics card quicker and generating shorter
refresh delay times.
Abstract: In this work, we study the impact of dynamically changing link slowdowns on the stability properties of packetswitched networks under the Adversarial Queueing Theory framework. Especially, we consider the Adversarial, Quasi-Static Slowdown Queueing Theory model, where each link slowdown may take on values in the two-valued set of integers {1, D} with D > 1 which remain fixed for a long time, under a (w, p)-adversary. In this framework, we present an innovative systematic construction for the estimation of adversarial injection rate lower bounds, which, if exceeded, cause instability in networks that use the LIS (Longest-in- System) protocol for contention-resolution. In addition, we show that a network that uses the LIS protocol for contention-resolution may result in dropping its instability bound at injection rates p > 0 when the network size and the high slowdown D take large values. This is the best ever known instability lower bound for LIS networks.
Abstract: In this study, effects of premixed and equivalence
ratios on CO and HC emissions of a dual fuel HCCI engine are
investigated. Tests were conducted on a single-cylinder engine with
compression ratio of 17.5. Premixed gasoline is provided by a
carburetor connected to intake manifold and equipped with a screw
to adjust premixed air-fuel ratio, and diesel fuel is injected directly
into the cylinder through an injector at pressure of 250 bars. A heater
placed at inlet manifold is used to control the intake charge
temperature. Optimal intake charge temperature results in better
HCCI combustion due to formation of a homogeneous mixture,
therefore, all tests were carried out over the optimum intake
temperature of 110-115 ºC. Timing of diesel fuel injection has a great
effect on stratification of in-cylinder charge and plays an important
role in HCCI combustion phasing. Experiments indicated 35 BTDC
as the optimum injection timing. Varying the coolant temperature in
a range of 40 to 70 ºC, better HCCI combustion was achieved at 50
ºC. Therefore, coolant temperature was maintained 50 ºC during all
tests. Simultaneous investigation of effective parameters on HCCI
combustion was conducted to determine optimum parameters
resulting in fast transition to HCCI combustion. One of the
advantages of the method studied in this study is feasibility of easy
and fast transition of typical diesel engine to a dual fuel HCCI
engine. Results show that increasing premixed ratio, while keeping
EGR rate constant, increases unburned hydrocarbon (UHC)
emissions due to quenching phenomena and trapping of premixed
fuel in crevices, but CO emission decreases due to increase in CO to
CO2 reactions.
Abstract: In the recent years multimedia traffic and in particular
VoIP services are growing dramatically. We present a new algorithm
to control the resource utilization and to optimize the voice codec
selection during SIP call setup on behalf of the traffic condition
estimated on the network path.
The most suitable methodologies and the tools that perform realtime
evaluation of the available bandwidth on a network path have
been integrated with our proposed algorithm: this selects the best
codec for a VoIP call in function of the instantaneous available
bandwidth on the path. The algorithm does not require any explicit
feedback from the network, and this makes it easily deployable over
the Internet. We have also performed intensive tests on real network
scenarios with a software prototype, verifying the algorithm
efficiency with different network topologies and traffic patterns
between two SIP PBXs.
The promising results obtained during the experimental validation
of the algorithm are now the basis for the extension towards a larger
set of multimedia services and the integration of our methodology
with existing PBX appliances.
Abstract: Physical urban form is recognized to be the media for
human transactions. It directly influences the travel demand of people
in a specific urban area and the amount of energy used for
transportation. Distorted, sprawling form often creates sustainability
problems in urban areas. It is declared in EU strategic planning
documents that compact urban form and mixed land use pattern must
be given the main focus to achieve better sustainability in urban
areas, but the methods to measure and compare these characteristics
are still not clear.
This paper presents the simple methods to measure the spatial
characteristics of urban form by analyzing the location and
distribution of objects in an urban environment. The extended CA
(cellular automata) model is used to simulate urban development
scenarios.
Abstract: In this paper we present a soft timing phase estimation (STPE) method for wireless mobile receivers operating in low signal to noise ratios (SNRs). Discrete Polyphase Matched (DPM) filters, a Log-maximum a posterior probability (MAP) and/or a Soft-output Viterbi algorithm (SOVA) are combined to derive a new timing recovery (TR) scheme. We apply this scheme to wireless cellular communication system model that comprises of a raised cosine filter (RCF), a bit-interleaved turbo-coded multi-level modulation (BITMM) scheme and the channel is assumed to be memory-less. Furthermore, no clock signals are transmitted to the receiver contrary to the classical data aided (DA) models. This new model ensures that both the bandwidth and power of the communication system is conserved. However, the computational complexity of ideal turbo synchronization is increased by 50%. Several simulation tests on bit error rate (BER) and block error rate (BLER) versus low SNR reveal that the proposed iterative soft timing recovery (ISTR) scheme outperforms the conventional schemes.
Abstract: The main objective of this paper is to determine the
isolated effect of silica fume on tensile, compressive and flexure strengths on high strength lightweight concrete. Many experiments
were carried out by replacing cement with different percentages of silica fume at different constant water-binder ratio keeping other mix
design variables constant. The silica fume was replaced by 0%, 5%,
10%, 15%, 20% and 25% for a water-binder ratios ranging from 0.26
to 0.42. For all mixes, split tensile, compressive and flexure strengths
were determined at 28 days. The results showed that the tensile, compressive and flexure strengths increased with silica fume incorporation but the optimum replacement percentage is not
constant because it depends on the water–cementitious material (w/cm) ratio of the mix. Based on the results, a relationship between
split tensile, compressive and flexure strengths of silica fume concrete was developed using statistical methods.
Abstract: The systematic manipulations of shapes and sizes of
inorganic compounds greatly benefit the various application fields
including optics, magnetic, electronics, catalysis and medicine.
However shape control has been much more difficult to achieve.
Hence exploration of novel method for the preparation of differently
shaped nanoparticles is challenging research area. II-VI group of
semiconductor cadmium sulphide (CdS) nanostructure with different
morphologies (such as, acicular like, mesoporous, spherical shapes)
and of crystallite sizes vary from 11 to 16 nm were successfully
synthesized by chemical aqueous precipitation of Cd2+ ions with
homogeneously released S2- ions from decomposition of cadmium
sulphate (CdSO4) and thioacetamide (CH3CSNH2) by annealing at
different radiations (microwave, ultrasonic and sunlight) with matter
and systematic research has been done for various factors affecting
the controlled growth rate of CdS nanoparticles. The obtained
nanomaterials have been characterized by X-ray Diffraction (XRD),
Fourier Transform Infrared Spectroscopy (FTIR),
Thermogravometric (DSC-TGA) analysis and Scanning Electron
Microscopy (SEM). The result indicates that on increasing the
reaction time particle size increases but on increasing the molar ratios
grain size decreases.
Abstract: Explosive welding is a process which uses explosive
detonation to move the flyer plate material into the base material to
produce a solid state joint. Experimental tests have been carried out
by other researchers; have been considered to explosively welded
aluminium 7039 and steel 4340 tubes in one step. The tests have been
done using various stand-off distances and explosive ratios. Various
interface geometries have been obtained from these experiments. In
this paper, all the experiments carried out were simulated using the
finite element method. The flyer plate and collision velocities
obtained from the analysis were validated by the pin-measurement
experiments. The numerical results showed that very high localized
plastic deformation produced at the bond interface. The
Ls_dyna_971 FEM has been used for all simulation process.
Abstract: The mechanical properties of granular solids are
dependent on the flow of stresses from one particle to another
through inter-particle contact. Although some experimental methods
have been used to study the inter-particle contacts in the past,
preliminary work with these techniques indicated that they do not
have the necessary resolution to distinguish between those contacts
that transmit the load and those that do not, especially for systems
with a wide distribution of particle sizes. In this research, computer
simulations are used to study the nature and distribution of contacts
in a compact with wide particle size distribution, representative of
aggregate size distribution used in asphalt pavement construction.
The packing fraction, the mean number of contacts and the
distribution of contacts were studied for different scenarios. A
methodology to distinguish and compute the fraction of load-bearing
particles and the fraction of space-filling particles (particles that do
not transmit any force) is needed for further investigation.