Abstract: Pipeline ADCs are becoming popular at high speeds
and with high resolution. This paper discusses the options of number
of bits/stage conversion techniques in pipelined ADCs and their
effect on Area, Speed, Power Dissipation and Linearity. The basic
building blocks like op-amp, Sample and Hold Circuit, sub converter,
DAC, Residue Amplifier used in every stage is assumed to be
identical. The sub converters use flash architectures. The design is
implemented using 0.18
Abstract: Successive event of explosion earthquake and harmonic tremor recorded at Semeru volcano were analyzed to investigate the dynamical system regarding to their eruptive mechanism. The eruptive activity at Semeru volcano East Java, Indonesia is intermittent emission of ash and bombs with Strombolian style which occurred at interval of 15 to 45 minutes. The explosive eruptions accompanied by explosion earthquakes and followed by volcanic tremor which generated by continuous emission of volcanic ash. The spectral and Lyapunov exponent of successive event of explosion and harmonic tremor were analyzed. Peak frequencies of explosion earthquakes range 1.2 to 1.9 Hz and those of the harmonic tremor have peak frequency range 1.5 — 2.2 Hz. The phase space is reconstructed and evaluated based on the Lyapunov exponents. Harmonic tremors have smaller Lyapunov exponent than explosion earthquakes. It can be considerably as correlated complexity of the mechanism from the variance of spectral and fractal dimension and can be concluded that the successive event of harmonic tremor and explosions are chaotic.
Abstract: Equipment miniaturisation offers several opportunities such as an increased surface-to-volume ratio and higher heat transfer coefficients. However, moving towards small-diameter channels demands extra attention to fouling, reliability and stable operation of the system. The present investigation explores possibilities to enhance the stability of the once-through micro evaporator by reducing its flow boiling induced pressure fluctuations. Experimental comparison shows that the measured reduction factor approaches a theoretically derived value. Pressure fluctuations are reduced by a factor of ten in the solid conical channel and a factor of 15 in the porous conical channel. This presumably leads to less backflow and therefore to a better flow control.
Abstract: This paper presents a novel algorithm for path planning of mobile robots in known 3D environments using Binary Integer Programming (BIP). In this approach the problem of path planning is formulated as a BIP with variables taken from 3D Delaunay Triangulation of the Free Configuration Space and solved to obtain an optimal channel made of connected tetrahedrons. The 3D channel is then partitioned into convex fragments which are used to build safe and short paths within from Start to Goal. The algorithm is simple, complete, does not suffer from local minima, and is applicable to different workspaces with convex and concave polyhedral obstacles. The noticeable feature of this algorithm is that it is simply extendable to n-D Configuration spaces.
Abstract: This paper presents the modeling of a MEMS based accelerometer in order to detect the presence of a wheel flat in the railway vehicle. A haversine wheel flat is assigned to one wheel of a 5 DOF pitch plane vehicle model, which is coupled to a 3 layer track model. Based on the simulated acceleration response obtained from the vehicle-track model, an accelerometer is designed that meets all the requirements to detect the presence of a wheel flat. The proposed accelerometer can survive in a dynamic shocking environment with acceleration up to ±150g. The parameters of the accelerometer are calculated in order to achieve the required specifications using lumped element approximation and the results are used for initial design layout. A finite element analysis code (COMSOL) is used to perform simulations of the accelerometer under various operating conditions and to determine the optimum configuration. The simulated results are found within about 2% of the calculated values, which indicates the validity of lumped element approach. The stability of the accelerometer is also determined in the desired range of operation including the condition under shock.
Abstract: Many works have been carried out to compare the
efficiency of several goodness of fit procedures for identifying
whether or not a particular distribution could adequately explain a
data set. In this paper a study is conducted to investigate the power
of several goodness of fit tests such as Kolmogorov Smirnov (KS),
Anderson-Darling(AD), Cramer- von- Mises (CV) and a proposed
modification of Kolmogorov-Smirnov goodness of fit test which
incorporates a variance stabilizing transformation (FKS). The
performances of these selected tests are studied under simple
random sampling (SRS) and Ranked Set Sampling (RSS). This
study shows that, in general, the Anderson-Darling (AD) test
performs better than other GOF tests. However, there are some
cases where the proposed test can perform as equally good as the
AD test.
Abstract: Integrated Total Quality Management (TQM) with
Lean Manufacturing (LM) is a system comprises of TQM with LM
principles and is associated with financial and nonfinancial
performance measurement indicators. The ultimate goal of this
system is to focus on achieving total customer satisfaction by
removing eight wastes available in any process in an organization.
A survey questionnaire was developed and distributed to 30 highly
active automotive vendors in Malaysia and analyzed by PASW
Statistics 18. It was found out that these vendors have been
practicing and measuring the effectiveness TQM and LM
implementation. More involvement of all Malaysian automotive
vendors will represent the exact status of current Malaysian
automotive industry in implementing TQM and LM and can
determine whether the industry is ready for integrated TQM and
LM system. This is the first study that combined 4 awards
practices, ISO/TS16949, Toyota Production System and
SAEJ4000.
Abstract: Extensive information is required within a R&D environment,
and a considerable amount of time and efforts are being
spent on finding the necessary information. An adaptive information
providing system would be beneficial to the environment, and a
conceptual model of the resources, people and context is mandatory
for developing such applications. In this paper, an information model
on various contexts and resources is proposed which provides the
possibility of effective applications for use in adaptive information
systems within a R&D project and meeting environment.
Abstract: The manufacturing transmission line tower parts has
being generated hazardous waste which is required proper disposal
of waste for protection of land pollution. Manufacturing Process in
the manufacturing of steel angle, plates, pipes, channels are passes
through conventional, semi automatic and CNC machines for
cutting, marking, punching, drilling, notching, bending operations.
All fabricated material Coated with thin layer of Zinc in Galvanizing
plant where molten zinc is used for coating. Prior to Galvanizing,
chemical like 33% concentrated HCl Acid, ammonium chloride and
d-oil being used for pretreatment of iron. The bath of water with
sodium dichromate is used for cooling and protection of the
galvanized steel. For the heating purpose the furnace oil burners are
used. These above process the Zinc dross, Zinc ash, ETP sludge and
waste pickled acid generated as hazardous waste. The RPG has
made captive secured land fill site, since 1997 since then it was
using for disposal of hazardous waste after completion of SLF
(Secured land fill) site. The RPG has raised height from ground
level then now it is being used for disposal of waste as he designed
the SLF after in creasing height of from GL it is functional without
leach ate or adverse impacts in the environment.
Abstract: Information hiding for authenticating and verifying the content integrity of the multimedia has been exploited extensively in the last decade. We propose the idea of using genetic algorithm and non-deterministic dependence by involving the un-watermarkable coefficients for digital image authentication. Genetic algorithm is used to intelligently select coefficients for watermarking in a DCT based image authentication scheme, which implicitly watermark all the un-watermarkable coefficients also, in order to thwart different attacks. Experimental results show that such intelligent selection results in improvement of imperceptibility of the watermarked image, and implicit watermarking of all the coefficients improves security against attacks such as cover-up, vector quantization and transplantation.
Abstract: Carrier mobility has become the most important
characteristic of high speed low dimensional devices. Due to
development of very fast switching semiconductor devices, speed of
computer and communication equipment has been increasing day by
day and will continue to do so in future. As the response of any
device depends on the carrier motion within the devices, extensive
studies of carrier mobility in the devices has been established
essential for the growth in the field of low dimensional devices.
Small-signal ac transport of degenerate two-dimensional hot
electrons in GaAs quantum wells is studied here incorporating
deformation potential acoustic, polar optic and ionized impurity
scattering in the framework of heated drifted Fermi-Dirac carrier
distribution. Delta doping is considered in the calculations to
investigate the effects of double delta doping on millimeter and submillimeter
wave response of two dimensional hot electrons in GaAs
nanostructures. The inclusion of delta doping is found to enhance
considerably the two dimensional electron density which in turn
improves the carrier mobility (both ac and dc) values in the GaAs
quantum wells thereby providing scope of getting higher speed
devices in future.
Abstract: Functional imaging procedures for the non-invasive assessment of tissue microcirculation are highly requested, but require a mathematical approach describing the trans- and intercapillary passage of tracer particles. Up to now, two theoretical, for the moment different concepts have been established for tracer kinetic modeling of contrast agent transport in tissues: pharmacokinetic compartment models, which are usually written as coupled differential equations, and the indicator dilution theory, which can be generalized in accordance with the theory of lineartime- invariant (LTI) systems by using a convolution approach. Based on mathematical considerations, it can be shown that also in the case of an open two-compartment model well-known from functional imaging, the concentration-time course in tissue is given by a convolution, which allows a separation of the arterial input function from a system function being the impulse response function, summarizing the available information on tissue microcirculation. Due to this reason, it is possible to integrate the open two-compartment model into the system-theoretic concept of indicator dilution theory (IDT) and thus results known from IDT remain valid for the compartment approach. According to the long number of applications of compartmental analysis, even for a more general context similar solutions of the so-called forward problem can already be found in the extensively available appropriate literature of the seventies and early eighties. Nevertheless, to this day, within the field of biomedical imaging – not from the mathematical point of view – there seems to be a trench between both approaches, which the author would like to get over by exemplary analysis of the well-known model.
Abstract: The two significant overvoltages in power system,
switching overvoltage and lightning overvoltage, are investigated in
this paper. Firstly, the effect of various power system parameters on
Line Energization overvoltages is evaluated by simulation in ATP.
The dominant parameters include line parameters; short-circuit
impedance and circuit breaker parameters. Solutions to reduce
switching overvoltages are reviewed and controlled closing using
switchsync controllers is proposed as proper method.
This paper also investigates lightning overvoltages in the
overhead-cable transition. Simulations are performed in
PSCAD/EMTDC. Surge arresters are applied in both ends of cable to
fulfill the insulation coordination. The maximum amplitude of
overvoltages inside the cable is surveyed which should be of great
concerns in insulation coordination studies.
Abstract: Hydrate phase equilibria for the binary CO2+water and
CH4+water mixtures in silica gel pore of nominal diameters 6, 30, and
100 nm were measured and compared with the calculated results based
on van der Waals and Platteeuw model. At a specific temperature,
three-phase hydrate-water-vapor (HLV) equilibrium curves for pore
hydrates were shifted to the higher-pressure condition depending on
pore sizes when compared with those of bulk hydrates. Notably,
hydrate phase equilibria for the case of 100 nominal nm pore size were
nearly identical with those of bulk hydrates. The activities of water in
porous silica gels were modified to account for capillary effect, and
the calculation results were generally in good agreement with the
experimental data. The structural characteristics of gas hydrates in
silica gel pores were investigated through NMR spectroscopy.
Abstract: The global chaos synchronization for a class of time-delayed power systems is investigated via observer-based approach. By employing the concepts of quadratic stability theory and generalized system model, a new sufficient criterion for constructing an observer is deduced. In contrast to the previous works, this paper proposes a theoretical and systematic design procedure to realize chaos synchronization for master-slave power systems. Finally, an illustrative example is given to show the applicability of the obtained scheme.
Abstract: The purpose of this study is to identify and evaluate
the scale of implementation of Just-In-Time (JIT) in the different industrial sectors in the Middle East. This study analyzes the empirical data collected by a questionnaire survey distributed to
companies in three main industrial sectors in the Middle East, which
are: food, chemicals and fabrics. The following main hypotheses is formulated and tested: (The requirements of JIT application differ
according to the type of industrial sector).Descriptive statistics and Box plot analysis were used to examine the hypotheses. This study indicates a reasonable evidence for accepting the main hypotheses. It
reveals that there is no standard way to adopt JIT as a production system. But each industrial sector should concentrate in the
investment on critical requirements that differ according to the nature
and strategy of production followed in that sector.
Abstract: Inconel718 has been widely used as a super alloy in aerospace application due to the high strength at elevated temperatures, satisfactory oxidation resistance and heat corrosion resistance. In this study, the Inconel718 has been fabricated using high technology of Metal Injection Molding (MIM) process due to the cost effective technique for producing small, complex and precision parts in high volume compared with conventional method through machining. Through MIM, the binder system is one of the most important criteria in order to successfully fabricate the Inconel718. Even though, the binder system is a temporary, but failure in the selection and removal of the binder system will affect on the final properties of the sintered parts. Therefore, the binder system based on palm oil derivative which is palm stearin has been formulated and developed to replace the conventional binder system. The rheological studies of the mixture between the powder and binders system have been determined properly in order to be successful during injection into injection molding machine. After molding, the binder holds the particles in place. The binder system has to be removed completely through debinding step. During debinding step, solvent debinding and thermal pyrolysis has been used to remove completely of the binder system. The debound part is then sintered to give the required physical and mechanical properties. The results show that the properties of the final sintered parts fulfill the Standard Metal Powder Industries Federation (MPIF) 35 for MIM parts.
Abstract: This study focuses on bureau management
technologies and information systems in developing countries.
Developing countries use such systems which facilitate executive and
organizational functions through the utilization of bureau
management technologies and provide the executive staff with
necessary information.
The concepts of data and information differ from each other in
developing countries, and thus the concepts of data processing and
information processing are different. Symbols represent ideas,
objects, figures, letters and numbers. Data processing system is an
integrated system which deals with the processing of the data related
to the internal and external environment of the organization in order
to make decisions, create plans and develop strategies; it goes
without saying that this system is composed of both human beings
and machines. Information is obtained through the acquisition and
the processing of data. On the other hand, data are raw
communicative messages. Within this framework, data processing
equals to producing plausible information out of raw data.
Organizations in developing countries need to obtain information
relevant to them because rapid changes in the organizational arena
require rapid access to accurate information. The most significant
role of the directors and managers who work in the organizational
arena is to make decisions. Making a correct decision is possible only
when the directors and managers are equipped with sound ideas and
appropriate information. Therefore, acquisition, organization and
distribution of information gain significance. Today-s organizations
make use of computer-assisted “Management Information Systems"
in order to obtain and distribute information.
Decision Support System which is closely related to practice is an
information system that facilitates the director-s task of making
decisions. Decision Support System integrates human intelligence,
information technology and software in order to solve the complex
problems. With the support of the computer technology and software
systems, Decision Support System produces information relevant to
the decision to be made by the director and provides the executive
staff with supportive ideas about the decision.
Artificial Intelligence programs which transfer the studies and
experiences of the people to the computer are called expert systems.
An expert system stores expert information in a limited area and can
solve problems by deriving rational consequences.
Bureau management technologies and information systems in
developing countries create a kind of information society and
information economy which make those countries have their places
in the global socio-economic structure and which enable them to play
a reasonable and fruitful role; therefore it is of crucial importance to
make use of information and management technologies in order to
work together with innovative and enterprising individuals and it is
also significant to create “scientific policies" based on information
and technology in the fields of economy, politics, law and culture.
Abstract: We propose a control design scheme that aims to
prevent undesirable liquid outpouring and suppress sloshing during
the forward and backward tilting phases of the pouring process, for
the case of liquid containers carried by manipulators. The proposed
scheme combines a partial inverse dynamics controller with a PID
controller, tuned with the use of a “metaheuristic" search algorithm.
The “metaheuristic" search algorithm tunes the PID controller based
on simulation results of the plant-s linearization around the operating
point corresponding to the critical tilting angle, where outpouring
initiates. Liquid motion is modeled using the well-known pendulumtype
model. However, the proposed controller does not require
measurements of the liquid-s motion within the tank.
Abstract: Security has been an important issue and concern in the
smart home systems. Smart home networks consist of a wide range of
wired or wireless devices, there is possibility that illegal access to
some restricted data or devices may happen. Password-based
authentication is widely used to identify authorize users, because this
method is cheap, easy and quite accurate. In this paper, a neural
network is trained to store the passwords instead of using verification
table. This method is useful in solving security problems that
happened in some authentication system. The conventional way to
train the network using Backpropagation (BPN) requires a long
training time. Hence, a faster training algorithm, Resilient
Backpropagation (RPROP) is embedded to the MLPs Neural
Network to accelerate the training process. For the Data Part, 200
sets of UserID and Passwords were created and encoded into binary
as the input. The simulation had been carried out to evaluate the
performance for different number of hidden neurons and combination
of transfer functions. Mean Square Error (MSE), training time and
number of epochs are used to determine the network performance.
From the results obtained, using Tansig and Purelin in hidden and
output layer and 250 hidden neurons gave the better performance. As
a result, a password-based user authentication system for smart home
by using neural network had been developed successfully.