Abstract: Stainless steel has been employed in many
engineering applications ranging from pharmaceutical equipment to
piping in the nuclear reactors and storage to chemical products. In
this attempt, simulation of fatigue crack growth based on
experimental results of austenitic stainless steel 304L was presented
using AFGROW code when NASGRO mode laws adopted. Double
through crack at hole specimen is used in this investigation under
constant amplitude loading. Effect of mean stress is highlighted.
Results show that fatigue crack growth rate (FCGR) and fatigue life
were affected by maximum applied load and dimension of hole. An
equivalent of Paris law for this material was estimated.
Abstract: This paper presents a low cost design of heart beat monitoring device using reflectance mode PhotoPlethysmography (PPG). PPG is known for its simple construction, ease of use and cost effectiveness and can provide information about the changes in cardiac activity as well as aid in earlier non-invasive diagnostics. The proposed device is divided into three phases. First is the detection of pulses through the fingertip. The signal is then passed to the signal processing unit for the purpose of amplification, filtering and digitizing. Finally the heart rate is calculated and displayed on the computer using parallel port interface. The paper is concluded with prototyping of the device followed by verification procedure of the heartbeat signal obtained in laboratory setting.
Abstract: Solution for the complete removal of carbon
monoxide from the exhaust gases still poses a challenge to the
researchers and this problem is still under development. Modeling for
reduction of carbon monoxide is carried out using heterogeneous
reaction using low cost non-noble metal based catalysts for the
purpose of controlling emissions released to the atmosphere. A
simple one-dimensional model was developed for the monolith using
hopcalite catalyst. The converter is assumed to be an adiabatic
monolith operating under warm-up conditions. The effect of inlet gas
temperatures and catalyst loading on carbon monoxide reduction
during cold start period in the converter is analysed.
Abstract: D-erythro-cyclohexylserine (D
chiral unnatural β-hydroxy amino acid expected for the synthesis of drug for AIDS treatment. To develop a continuous bioconversion
system with whole cell biocatalyst of D-threonine aldolase (D genes for the D-erythro-CHS production, D-threonine aldolase gene
was amplified from Ensifer arboris 100383 by direct PCR amplication using two degenerated oligonucleotide primers designed based on
genomic sequence of Shinorhizobium meliloti
Sequence analysis of the cloned DNA fragment revealed one
open-reading frame of 1059 bp and 386 amino acids. This putative
D-TA gene was cloned into NdeI and EcoRI (pEnsi
His-tag sequence or BamHI (pEnsi-DTA[2])
sequence of the pET21(a) vector. The expression level of the cloned gene was extremely overexpressed by E. coli BL21(DE3) transformed with pEnsi-DTA[1] compared to E. coli BL21(DE3) transformed with
pEnsi-DTA[2]. When the cells expressing the wild
used for D-TA enzyme activity, 12 mM glycine was successfully
detected in HPLC analysis. Moreover, the whole cells harbouring the
recombinant D-TA was able to synthesize D-erythro
of 0.6 mg/ml in a batch reaction.
Abstract: European Union candidate status provides a
strong motivation for decision-making in the candidate
countries in shaping the regional development policy where
there is an envisioned transfer of power from center to the
periphery. The process of Europeanization anticipates the
candidate countries configure their regional institutional
templates in the context of the requirements of the European
Union policies and introduces new instruments of incentive
framework of enlargement to be employed in regional
development schemes. It is observed that the contribution of
the local actors to the decision making in the design of the
allocation architectures enhances the efficiency of the funds
and increases the positive effects of the projects funded under
the regional development objectives. This study aims at
exploring the performances of the three regional development
grant schemes in Turkey, established and allocated under the
pre-accession process with a special emphasis given to the
roles of the national and local actors in decision-making for
regional development. Efficiency analyses have been
conducted using the DEA methodology which has proved to
be a superior method in comparative efficiency and
benchmarking measurements. The findings of this study as
parallel to similar international studies, provides that the
participation of the local actors to the decision-making in
funding contributes both to the quality and the efficiency of
the projects funded under the EU schemes.
Abstract: Due to the recovering global economy, enterprises are
increasingly focusing on logistics. Investing in logistic measures for
a production generates a large potential for achieving a good starting
point within a competitive field. Unlike during the global economic
crisis, enterprises are now challenged with investing available capital
to maximize profits. In order to be able to create an informed and
quantifiably comprehensible basis for a decision, enterprises need an
adequate model for logistically and monetarily evaluating measures
in production. The Collaborate Research Centre 489 (SFB 489) at the
Institute for Production Systems (IFA) developed a Logistic
Information System which provides support in making decisions and
is designed specifically for the forging industry. The aim of a project
that has been applied for is to now transfer this process in order to
develop a universal approach to logistically and monetarily evaluate
measures in production.
Abstract: Information is power. Geographical information is an
emerging science that is advancing the development of knowledge to
further help in the understanding of the relationship of “place" with
other disciplines such as crime. The researchers used crime data for
the years 2004 to 2007 from the Baguio City Police Office to
determine the incidence and actual locations of crime hotspots.
Combined qualitative and quantitative research methodology was
employed through extensive fieldwork and observation, geographic
visualization with Geographic Information Systems (GIS) and Global
Positioning Systems (GPS), and data mining. The paper discusses
emerging geographic visualization and data mining tools and
methodologies that can be used to generate baseline data for
environmental initiatives such as urban renewal and rejuvenation.
The study was able to demonstrate that crime hotspots can be
computed and were seen to be occurring to some select places in the
Central Business District (CBD) of Baguio City. It was observed that
some characteristics of the hotspot places- physical design and milieu
may play an important role in creating opportunities for crime. A list
of these environmental attributes was generated. This derived
information may be used to guide the design or redesign of the urban
environment of the City to be able to reduce crime and at the same
time improve it physically.
Abstract: As networking has become popular, Web-learning
tends to be a trend while designing a tool. Moreover, five-axis
machining has been widely used in industry recently; however, it has
potential axial table colliding problems. Thus this paper aims at
proposing an efficient web-learning collision detection tool on
five-axis machining. However, collision detection consumes heavy
resource that few devices can support, thus this research uses a
systematic approach based on web knowledge to detect collision. The
methodologies include the kinematics analyses for five-axis motions,
separating axis method for collision detection, and computer
simulation for verification. The machine structure is modeled as STL
format in CAD software. The input to the detection system is the
g-code part program, which describes the tool motions to produce the
part surface. This research produced a simulation program with C
programming language and demonstrated a five-axis machining
example with collision detection on web site. The system simulates the
five-axis CNC motion for tool trajectory and detects for any collisions
according to the input g-codes and also supports high-performance
web service benefiting from C. The result shows that our method
improves 4.5 time of computational efficiency, comparing to the
conventional detection method.
Abstract: This research contribution is drafted to present the
orbit design, orbit propagator and geomagnetic field estimator for the
nanosatellites specifically for the upcoming CUBESAT, ICUBE-1 of
the Institute of Space Technology (IST), Islamabad, Pakistan. The
ICUBE mission is designed for the low earth orbit at the approximate
height of 700KM. The presented research endeavor designs the
Keplarian elements for ICUBE-1 orbit while incorporating the
mission requirements and propagates the orbit using J2 perturbations,
The attitude determination system of the ICUBE-1 consists of
attitude determination sensors like magnetometer and sun sensor. The
Geomagnetic field estimator is developed according to the model of
International Geomagnetic Reference Field (IGRF) for comparing the
magnetic field measurements by the magnetometer for attitude
determination. The output of the propagator namely the Keplarians
position and velocity vectors and the magnetic field vectors are
compared and verified with the same scenario generated in the
Satellite Tool Kit (STK).
Abstract: Segmentation techniques based on Active Contour
Models have been strongly benefited from the use of prior information
during their evolution. Shape prior information is captured from
a training set and is introduced in the optimization procedure to
restrict the evolution into allowable shapes. In this way, the evolution
converges onto regions even with weak boundaries. Although
significant effort has been devoted on different ways of capturing
and analyzing prior information, very little thought has been devoted
on the way of combining image information with prior information.
This paper focuses on a more natural way of incorporating the
prior information in the level set framework. For proof of concept
the method is applied on hippocampus segmentation in T1-MR
images. Hippocampus segmentation is a very challenging task, due
to the multivariate surrounding region and the missing boundary
with the neighboring amygdala, whose intensities are identical. The
proposed method, mimics the human segmentation way and thus
shows enhancements in the segmentation accuracy.
Abstract: In this paper the reference current for Voltage Source
Converter (VSC) of the Shunt Active Power Filter (SAPF) is
generated using Synchronous Reference Frame method,
incorporating the PI controller with anti-windup scheme. The
proposed method improves the harmonic filtering by compensating
the winding up phenomenon caused by the integral term of the PI
controller.
Using Reference Frame Transformation, the current is transformed
from om a - b - c stationery frame to rotating 0 - d - q frame. Using
the PI controller, the current in the 0 - d - q frame is controlled to
get the desired reference signal. A controller with integral action
combined with an actuator that becomes saturated can give some
undesirable effects. If the control error is so large that the integrator
saturates the actuator, the feedback path becomes ineffective because
the actuator will remain saturated even if the process output changes.
The integrator being an unstable system may then integrate to a very
large value, the phenomenon known as integrator windup.
Implementing the integrator anti-windup circuit turns off the
integrator action when the actuator saturates, hence improving the
performance of the SAPF and dynamically compensating harmonics
in the power network. In this paper the system performance is
examined with Shunt Active Power Filter simulation model.
Abstract: Although services play a crucial role in economy,
service did not gain as much importance as productivity management
in manufacturing. This paper presents key findings from literature
and practice. Based on an initial definition of complex services, seven
productivity concepts are briefly presented and assessed by relevant,
complex service specific criteria. Following the findings a complex
service productivity model is proposed. The novel model comprises
of all specific dimensions of service provision from both, the
provider-s as well as costumer-s perspective. A clear assignment of
identified value drivers and relationships between them is presented.
In order to verify the conceptual service productivity model a case
study from a project engineering department of a chemical plant
development and construction company is presented.
Abstract: In this study we present our developed formative
assessment tool for students' assignments. The tool enables lecturers
to define assignments for the course and assign each problem in each
assignment a list of criteria and weights by which the students' work
is evaluated. During assessment, the lecturers feed the scores for each
criterion with justifications. When the scores of the current
assignment are completely fed in, the tool automatically generates
reports for both students and lecturers. The students receive a report
by email including detailed description of their assessed work, their
relative score and their progress across the criteria along the course
timeline. This information is presented via charts generated
automatically by the tool based on the scores fed in. The lecturers
receive a report that includes summative (e.g., averages, standard
deviations) and detailed (e.g., histogram) data of the current
assignment. This information enables the lecturers to follow the class
achievements and adjust the learning process accordingly. The tool
was examined on two pilot groups of college students that study a
course in (1) Object-Oriented Programming (2) Plane Geometry.
Results reveal that most of the students were satisfied with the
assessment process and the reports produced by the tool. The
lecturers who used the tool were also satisfied with the reports and
their contribution to the learning process.
Abstract: Adhesively bonded joints are preferred over the
conventional methods of joining such as riveting, welding, bolting
and soldering. Some of the main advantages of adhesive joints
compared to conventional joints are the ability to join dissimilar
materials and damage-sensitive materials, better stress distribution,
weight reduction, fabrication of complicated shapes, excellent
thermal and insulation properties, vibration response and enhanced
damping control, smoother aerodynamic surfaces and an
improvement in corrosion and fatigue resistance. This paper presents
the behavior of adhesively bonded joints subjected to combined
thermal loadings, using the numerical methods. The joint
configuration considers aluminum as central adherend with six
different outer adherends including aluminum, steel, titanium, boronepoxy,
unidirectional graphite-epoxy and cross-ply graphite-epoxy
and epoxy-based adhesives. Free expansion of the joint in x
direction was permitted and stresses in adhesive layer and interfaces
calculated for different adherends.
Abstract: A procedure for the preparation of clarified Pawpaw
Juice was developed. About 750ml Pawpaw pulp was measured into
2 measuring cylinders A & B of capacity 1 litre heated to 400C,
cooled to 200C. 30mls pectinase was added into cylinder A, while
30mls distilled water was added into cylinder B. Enzyme treated
sample (A) was allowed to digest for 5hours after which it was heated
to 900C for 15 minutes to inactivate the enzyme. The heated sample
was cooled and with the aid of a mucillin cloth the pulp was filtered
to obtain the clarified pawpaw juice. The juice was filled into 100ml
plastic bottles, pasteurized at 950C for 45 minutes, cooled and stored
at room temperature. The sample treated with 30mls distilled water
also underwent the same process. Freshly pasteurized sample was
analyzed for specific gravity, titratable acidity, pH, sugars and
ascorbic acid. The remaining sample was then stored for 2 weeks and
the above analyses repeated. There were differences in the results of
the freshly pasteurized samples and stored sample in pH and ascorbic
acid levels, also sample treated with pectinase yielded higher
volumes of juice than that treated with distilled water.
Abstract: Recently there has been a growing interest in the field
of bio-mimetic robots that resemble the behaviors of an insect or an
aquatic animal, among many others. One of various bio-mimetic robot
applications is to explore pipelines, spotting any troubled areas or
malfunctions and reporting its data. Moreover, the robot is able to
prepare for and react to any abnormal routes in the pipeline. Special
types of mobile robots are necessary for the pipeline monitoring tasks.
In order to move effectively along a pipeline, the robot-s movement
will resemble that of insects or crawling animals. When situated in
massive pipelines with complex routes, the robot places fixed sensors
in several important spots in order to complete its monitoring. This
monitoring task is to prevent a major system failure by preemptively
recognizing any minor or partial malfunctions. Areas uncovered by
fixed sensors are usually impossible to provide real-time observation
and examination, and thus are dependent on periodical offline
monitoring. This paper proposes a monitoring system that is able to
monitor the entire area of pipelines–with and without fixed
sensors–by using the bio-mimetic robot.
Abstract: The phenomenon of global warming or climate
change has led to many environmental issues including higher
atmospheric temperatures, intense precipitation, increased
greenhouse gaseous emissions and increased indoor discomfort.
Studies have shown that bringing nature to the roof such as
constructing green roof and implementing high-reflective roof may
give positive impact in mitigating the effects of global warming and
in increasing thermal comfort sensation inside buildings. However,
no study has been conducted to compare both types of passive roof
treatments in Malaysia in order to increase thermal comfort in
buildings. Therefore, this study is conducted to investigate the effect
of green roof and white painted roof as passive roof treatment in
improving indoor comfort of Malaysian homes. This study uses an
experimental approach in which the measurements of temperatures
are conducted on the case study building. The measurements of
outdoor and indoor environments were conducted on the flat roof
with two different types of roof treatment that are green roof and
white roof. The measurement of existing black bare roof was also
conducted to act as a control for this study.
Abstract: Emergence of smartphones brings to live the concept
of converged devices with the availability of web amenities. Such
trend also challenges the mobile devices manufactures and service
providers in many aspects, such as security on mobile phones,
complex and long time design flow, as well as higher development
cost. Among these aspects, security on mobile phones is getting more
and more attention. Microkernel based virtualization technology will
play a critical role in addressing these challenges and meeting mobile
market needs and preferences, since virtualization provides essential
isolation for security reasons and it allows multiple operating systems
to run on one processor accelerating development and cutting development
cost. However, virtualization benefits do not come for free.
As an additional software layer, it adds some inevitable virtualization
overhead to the system, which may decrease the system performance.
In this paper we evaluate and analyze the virtualization performance
cost of L4 microkernel based virtualization on a competitive mobile
phone by comparing the L4Linux, a para-virtualized Linux on top of
L4 microkernel, with the native Linux performance using lmbench
and a set of typical mobile phone applications.
Abstract: The term private equity usually refers to any type of
equity investment in an asset in which the equity is not freely
tradable on a public stock market. Some researchers believe that
private equity contributed to the extent of the crisis and increased
the pace of its spread over the world. We do not agree with this.
On the other hand, we argue that during the economic recession
private equity might become an important source of funds for firms
with special needs (e.g. for firms seeking buyout financing, venture
capital, expansion capital or distress debt financing). However,
over-regulation of private equity in both the European Union and
the US can slow down this specific funding channel to the
economy and deepen credit crunch during global crises.
Abstract: The last Assessment Report of the Intergovernmental
Panel on Climate Change, stating that the greatest risk in climate
change affects sustainability is now widely known and accepted.
However, it has not provoked substantial reaction and attention in
Hungary, while international and national efforts have also not
achieved expected results so far. Still, there are numerous examples
on different levels (national, regional, local, household) making
considerable progress in limiting their own emissions and making
steps toward mitigation of and adaptation to climate change. The
local level is exceptionally important in sustainability adaptation, as
local communities are often able to adapt more flexibly to changes in
the natural environment.The aim of this paper is to attempt a review
of the national climate policy and the local climate change strategies
in Hungary considering sustainable development.