Abstract: Platinum oxide nanoparticles were prepared by a
simple hydrothermal route and chemical reduction using
carbohydrates (Fructose and sucrose) as the reducing and
stabilizing agents. The crystallite size of these nanoparticles was
evaluated from X-ray diffraction (XRD), atomic force microscopy
(AFM) and transmission electron microscopy (TEM) and was
found to be 10 nm as shown in figure 1, which is the
demonstration of EM bright field and transmission electron
microscopy. The effect of carbohydrates on the morphology of the
nanoparticles was studied using TEM (Figure 1). The
nanoparticles (100 μg/ml) were administered to the Pseudomonas
Stutzeri and Lactobacillus cultures and the incubation was done at
35 oC for 24 hours. The nanocomposites exhibited interesting
inhibitory as well as bactericidal activity against P. Stutzeri and
and Lactobacillus species. Incorporation of nanoparticles also
increased the thermal stability of the carbohydrates.
Abstract: The present work is concerned with the free
convective two dimensional flow and heat transfer, in isotropic fluid
filled porous rectangular enclosure with differentially heated walls for
steady state incompressible flow have been investigated for non-
Darcy flow model. Effects of Darcy number (0.0001 £Da£ 10),
Rayleigh number (10 £Ra£ 5000), and aspect ratio (0.25 £AR£ 4), for
a range of porosity (0.4 £e£ 0.9) with and without moving lower wall
have been studied. The cavity was insulated at the lower and upper
surfaces. The right and left heated surfaces allows convective
transport through the porous medium, generating a thermal
stratification and flow circulations. It was found that the Darcy
number, Rayleigh number, aspect ratio, and porosity considerably
influenced characteristics of flow and heat transfer mechanisms. The
results obtained are discussed in terms of the Nusselt number,
vectors, contours, and isotherms.
Abstract: The InAlGaN alloy has only recently began receiving
serious attention into its growth and application. High quality InGaN
films have led to the development of light emitting diodes (LEDs) and
blue laser diodes (LDs). The quaternary InAlGaN however, represents
a more versatile material since the bandgap and lattice constant can be
independently varied. We report an ultraviolet (UV) quaternary
InAlGaN multi-quantum wells (MQWs) LD study by using the
simulation program of Integrated System Engineering (ISE TCAD).
Advanced physical models of semiconductor properties were used in
order to obtain an optimized structure. The device performance which
is affected by piezoelectric and thermal effects was studied via
drift-diffusion model for carrier transport, optical gain and loss. The
optical performance of the UV LD with different numbers of quantum
wells was numerically investigated. The main peak of the emission
wavelength for double quantum wells (DQWs) was shifted from 358
to 355.8 nm when the forward current was increased. Preliminary
simulated results indicated that better output performance and lower
threshold current could be obtained when the quantum number is four,
with output power of 130 mW and threshold current of 140 mA.
Abstract: Threedimensional numerical simulations are conducted on a full scale CANDU Moderator and Transient variations of the temperature and velocity distributions inside the tank are determined. The results show that the flow and temperature distributions inside the moderator tank are three dimensional and no symmetry plane can be identified.Competition between the upward moving buoyancy driven flows and the downward moving momentum driven flows, results in the formation of circulation zones. The moderator tank operates in the buoyancy driven mode and any small disturbances in the flow or temperature makes the system unstable and asymmetric. Different types of temperature fluctuations are noted inside the tank: (i) large amplitude are at the boundaries between the hot and cold (ii) low amplitude are in the core of the tank (iii) high frequency fluctuations are in the regions with high velocities and (iv) low frequency fluctuations are in the regions with lower velocities.
Abstract: In this paper, the babbitting of a bearing in boiler feed pump of an electromotor has been studied. These bearings have an important role in reducing the shut down times in the pumps, compressors and turbines. The most conventional method in babbitting is casting as a melting method. The comparison between thermal spray and casting methods in babbitting shows that the thermal spraying babbitt layer has better performance and tribological behavior. The metallurgical and tribological analysis such as SEM, EDS and wet chemical analysis has been made in the Babbitt alloys and worn surfaces. Two type of babbitt materials: tinbase and lead-base babbitt was used. The benefits of thermally sprayed babbitt layers are completely clear especially in large bearings.
Abstract: Bentonitic material from South Aswan, Egypt was evaluated in terms of mineral-ogy and chemical composition as bleaching clay in refining of transformer oil before and after acid activation and thermal treatment followed by acid leaching using HCl and H2SO4 for different contact times. Structural modification and refining power of bento-nite were investigated during modification by means of X-ray diffraction and infrared spectroscopy. The results revealed that the activated bentonite could be used for refining of transformer oil. The oil parameters such as; dielectric strength, viscosity and flash point had been improved. The dielectric breakdown strength of used oil increased from 29 kV for used oil treated with unactivated bentonite to 74 kV after treatment with activated bentonite. Kinematic Viscosity changed from 19 to 11 mm2 /s after treatment with activated bentonite. However, flash point achieved 149 ºC.
Abstract: The experimental thermal performance of two heat
exchangers in closed-wet cooling tower (CWCT) was investigated in
this study. The test sections are heat exchangers which have multi path
that is used as the entrance of cooling water and are consisting of
bare-type copper tubes between 15.88mm and 19.05mm. The process
fluids are the cooling water that flows from top part of heat exchanger
to bottom side in the inner side of tube, and spray water that flows
gravitational direction in the outer side of it. Air contacts its outer side
of that as it counterflows. Heat and mass transfer coefficients and
cooling capacity were calculated with variations of process fluids,
multi path and different diameter tubes to figure out the performance
of characteristics of CWCT.
The main results were summarized as follows: The results show this
experiment is reliable with values of heat and mass transfer
coefficients comparing to values of correlations. Heat and mass
transfer coefficients and cooling capacity of two paths are higher than
these with one path using 15.88 and 19.05mm tubes. Cooling capacity
per unit volume with 15.88mm tube using one and two paths are
higher than 19.05mm tube due to increase of surface area per unit
volume.
Abstract: This paper reports on the enhanced photoluminescence
(PL) of nanocomposites through the layered structuring of phosphor
and quantum dot (QD). Green phosphor of Sr2SiO4:Eu, red QDs of
CdSe/CdS/CdZnS/ZnS core-multishell, and thermo-curable resin
were used for this study. Two kinds of composite (layered and mixed)
were prepared, and the schemes for optical energy transfer between
QD and phosphor were suggested and investigated based on PL decay
characteristics. It was found that the layered structure is more effective
than the mixed one in the respects of PL intensity, PL decay and
thermal loss. When this layered nanocomposite (QDs on phosphor) is
used to make white light emitting diode (LED), the brightness is
increased by 37 %, and the color rendering index (CRI) value is raised
to 88.4 compared to the mixed case of 80.4.
Abstract: To understand working features of a micro combustor,
a computer code has been developed to study combustion of
hydrogen–air mixture in a series of chambers with same shape aspect
ratio but various dimensions from millimeter to micrometer level.
The prepared algorithm and the computer code are capable of
modeling mixture effects in different fluid flows including chemical
reactions, viscous and mass diffusion effects. The effect of various
heat transfer conditions at chamber wall, e.g. adiabatic wall, with
heat loss and heat conduction within the wall, on the combustion is
analyzed. These thermal conditions have strong effects on the
combustion especially when the chamber dimension goes smaller and
the ratio of surface area to volume becomes larger.
Both factors, such as larger heat loss through the chamber wall
and smaller chamber dimension size, may lead to the thermal
quenching of micro-scale combustion. Through such systematic
numerical analysis, a proper operation space for the micro-combustor
is suggested, which may be used as the guideline for microcombustor
design. In addition, the results reported in this paper
illustrate that the numerical simulation can be one of the most
powerful and beneficial tools for the micro-combustor design,
optimization and performance analysis.
Abstract: In the present study, the incorporation of graphene
into blends of acrylonitrile-butadiene-styrene terpolymer with
polypropylene (ABS/PP) was investigated focusing on the
improvement of their thermomechanical characteristics and the effect
on their rheological behavior. The blends were prepared by melt
mixing in a twin-screw extruder and were characterized by measuring
the MFI as well as by performing DSC, TGA and mechanical tests.
The addition of graphene to ABS/PP blends tends to increase their
melt viscosity, due to the confinement of polymer chains motion.
Also, graphene causes an increment of the crystallization temperature
(Tc), especially in blends with higher PP content, because of the
reduction of surface energy of PP nucleation, which is a consequence
of the attachment of PP chains to the surface of graphene through the
intermolecular CH-π interaction. Moreover, the above nanofiller
improves the thermal stability of PP and increases the residue of
thermal degradation at all the investigated compositions of blends,
due to the thermal isolation effect and the mass transport barrier
effect. Regarding the mechanical properties, the addition of graphene
improves the elastic modulus, because of its intrinsic mechanical
characteristics and its rigidity, and this effect is particularly strong in
the case of pure PP.
Abstract: This paper deals with the application of artificial
neural network (ANN) and fuzzy based Adaptive Neuro Fuzzy
Inference System(ANFIS) approach to Load Frequency Control
(LFC) of multi unequal area hydro-thermal interconnected power
system. The proposed ANFIS controller combines the advantages of
fuzzy controller as well as quick response and adaptability nature of
ANN. Area-1 and area-2 consists of thermal reheat power plant
whereas area-3 and area-4 consists of hydro power plant with electric
governor. Performance evaluation is carried out by using intelligent
controller like ANFIS, ANN and Fuzzy controllers and conventional
PI and PID control approaches. To enhance the performance of
intelligent and conventional controller sliding surface is included.
The performances of the controllers are simulated using
MATLAB/SIMULINK package. A comparison of ANFIS, ANN,
Fuzzy, PI and PID based approaches shows the superiority of
proposed ANFIS over ANN & fuzzy, PI and PID controller for 1%
step load variation.
Abstract: This paper deals with the problem of thermal and
mechanical shocks, which rising during operation, mostly at
interrupted cut. Here will be solved their impact on the cutting edge
tool life, the impact of coating technology on resistance to shocks
and experimental determination of tool life in heating flame.
Resistance of removable cutting edges against thermal and
mechanical shock is an important indicator of quality as well as its
abrasion resistance. Breach of the edge or its crumble may occur due
to cyclic loading. We can observe it not only during the interrupted
cutting (milling, turning areas abandoned hole or slot), but also in
continuous cutting. This is due to the volatility of cutting force on
cutting. Frequency of the volatility in this case depends on the type
of rising chips (chip size element). For difficult-to-machine materials
such as austenitic steel particularly happened at higher cutting speeds
for the localization of plastic deformation in the shear plane and for
the inception of separate elements substantially continuous chips.
This leads to variations of cutting forces substantially greater than for
other types of steel.
Abstract: In this paper, a thermal model of cast- resin dry type
transformer is proposed. The proposed thermal model is solved by
finite element technique to get the temperature at any location of the
transformer. The basic modes of heat transfer such as conduction;
convection and radiation are used to get the steady state temperature
distribution of the transformer. The predicted temperatures are
compared with experimental results reported in this paper and it is
found a good agreement between them. The effects of various
parameters such as width of air duct, ambient temperature and
emissivity of the outer surface were also studied.
Abstract: Heat pipes are two-phase heat transfer devices with
high effective thermal conductivity. Due to the high heat transport
capacity, heat exchanger with heat pipes has become much smaller
than traditional heat exchangers in handling high heat fluxes. With
the working fluid in a heat pipe, heat can be absorbed on the
evaporator region and transported to the condenser region where the
vapour condenses releasing the heat to the cooling media. Heat pipe
technology has found increasing applications in enhancing the
thermal performance of heat exchangers in microelectranics, energy
saving in HVAC systems for operating rooms,surgery centers, hotels,
cleanrooms etc, temperature regulation systems for the human body
and other industrial sectors. Development activity in heat pipe and
thermosyphon technology in asia in recent years is surveyed. Some
new results obtained in Australia and other countries are also
included.
Abstract: Regenerative gas turbine engine cycle is presented that yields higher cycle efficiencies than simple cycle operating under the same conditions. The power output, efficiency and specific fuel consumption are simulated with respect to operating conditions. The analytical formulae about the relation to determine the thermal efficiency are derived taking into account the effected operation conditions (ambient temperature, compression ratio, regenerator effectiveness, compressor efficiency, turbine efficiency and turbine inlet temperature). Model calculations for a wide range of parameters are presented, as are comparisons with simple gas turbine cycle. The power output and thermal efficiency are found to be increasing with the regenerative effectiveness, and the compressor and turbine efficiencies. The efficiency increased with increase the compression ratio to 5, then efficiency decreased with increased compression ratio, but in simple cycle the thermal efficiency always increase with increased in compression ratio. The increased in ambient temperature caused decreased thermal efficiency, but the increased in turbine inlet temperature increase thermal efficiency.
Abstract: Lattice Monte Carlo methods are an excellent
choice for the simulation of non-linear thermal diffusion
problems. In this paper, and for the first time, Lattice Monte
Carlo analysis is performed on thermal diffusion combined
with convective heat transfer. Laminar flow of water modeled
as an incompressible fluid inside a copper pipe with a constant
surface temperature is considered. For the simulation of
thermal conduction, the temperature dependence of the
thermal conductivity of the water is accounted for. Using the
novel Lattice Monte Carlo approach, temperature distributions
and energy fluxes are obtained.
Abstract: Rice husk is a lignocellulosic source that can be
converted to ethanol. Three hundreds grams of rice husk was mixed
with 1 L of 0.18 N sulfuric acid solutions then was heated in an
autoclave. The reaction was expected to be at constant temperature
(isothermal), but before that temperature was achieved, reaction has
occurred. The first liquid sample was taken at temperature of 140 0C
and repeated every 5 minute interval. So the data obtained are in the
regions of non-isothermal and isothermal. It was observed that the
degradation has significant effects on the ethanol production. The
kinetic constants can be expressed by Arrhenius equation with the
frequency factors for hydrolysis and sugar degradation of 1.58 x 105
1/min and 2.29 x 108 L/mole/min, respectively, while the activation
energies are 64,350 J/mole and 76,571 J/mole. The highest ethanol
concentration from fermentation is 1.13% v/v, attained at 220 0C.
Abstract: Coal fly ash (CFA) generated by coal-based thermal
power plants is mainly composed of some oxides having high
crystallinity, like quartz and mullite. In this study, the effect of CFA
crystallinity toward lead adsorption capacity was investigated. To get
solid with various crystallinity, the solution of sodium hydroxide
(NaOH) of 1-7 M was used to treat CFA at various temperature and
reflux time. Furthermore, to evaluate the effect of NaOH-treated CFA
with respect to adsorption capacity, the treated CFA were examine as
adsorbent for removing lead in the solution. The result shows that
using NaOH to treat CFA causes crystallinity of quartz and mullite
decrease. At higher NaOH concentration (>3M), in addition the
damage of quartz and mullite crystallinity is followed by crystal
formation called hydroxysodalite. The lower crystalllinity, the higher
adsorption capacity.
Abstract: In this study, an analysis has been performed for
free convection with radiation effect over a thermal forming
nonlinearly stretching sheet. Parameters n, k0, Pr, G represent
the dominance of the nonlinearly effect, radiation effect, heat
transfer and free convection effects which have been presented
in governing equations, respectively. The similarity
transformation and the finite-difference methods have been
used to analyze the present problem. From the results, we find
that the effects of parameters n, k0, Pr, Ec and G to the
nonlinearly stretching sheet. The increase of Prandtl number Pr,
free convection parameter G or radiation parameter k0 resulting
in the increase of heat transfer effects, but increase of the
viscous dissipation number Ec will decrease of heat transfer
effect.
Abstract: In this paper, a Dynamic Economic Dispatch (DED) model is developed for the system consisting of both thermal generators and wind turbines. The inclusion of a significant amount of wind energy into power systems has resulted in additional constraints on DED to accommodate the intermittent nature of the output. The probability of stochastic wind power based on the Weibull probability density function is included in the model as a constraint; A Here-and-Now Approach. The Environmental Protection Agency-s hourly emission target, which gives the maximum emission during the day, is used as a constraint to reduce the atmospheric pollution. A 69-bus test system with non-smooth cost function is used to illustrate the effectiveness of the proposed model compared with static economic dispatch model with including the wind power.