Abstract: The effect of various humidities on process yields and
degrees of crystallinity for spray-dried powders from spray drying of
lactose with humid air in a straight-through system have been
studied. It has been suggested by Williams–Landel–Ferry kinetics
(WLF) that a higher particle temperature and lower glass-transition
temperature would increase the crystallization rate of the particles
during the spray-drying process. Freshly humidified air produced by
a Buchi-B290 spray dryer as a humidifier attached to the main spray
dryer decreased the particle glass-transition temperature (Tg), while
allowing the particle temperature (Tp) to reach higher values by using
an insulated drying chamber. Differential scanning calorimetry
(DSC) and moisture sorption analysis were used to measure the
degree of crystallinity for the spray-dried lactose powders. The
results showed that higher Tp-Tg, as a result of applying humid air,
improved the process yield from 21 ± 4 to 26 ± 2% and crystallinity
of the particles by decreasing the latent heat of crystallization from
43 ± 1 to 30 ± 11 J/g and the sorption peak height from 7.3 ± 0.7% to
6 ± 0.7%.
Abstract: An analysis of the Australian Diabetes Screening
Study estimated undiagnosed diabetes mellitus [DM] prevalence in a
high risk general practice based cohort. DM prevalence varied from
9.4% to 18.1% depending upon the diagnostic criteria utilised with
age being a highly significant risk factor. Utilising the gold standard
oral glucose tolerance test, the prevalence of DM was 22-23% in
those aged >= 70 years and
Abstract: The generalized wave equation models various
problems in sciences and engineering. In this paper, a new three-time
level implicit approach based on cubic trigonometric B-spline for the
approximate solution of wave equation is developed. The usual finite
difference approach is used to discretize the time derivative while
cubic trigonometric B-spline is applied as an interpolating function in
the space dimension. Von Neumann stability analysis is used to
analyze the proposed method. Two problems are discussed to exhibit
the feasibility and capability of the method. The absolute errors and
maximum error are computed to assess the performance of the
proposed method. The results were found to be in good agreement
with known solutions and with existing schemes in literature.
Abstract: From an organizational perspective, leaders are a
variation of the same talent pool in that they all score a larger than
average value on the bell curve that maps leadership behaviors and
characteristics, namely competence, vision, communication,
confidence, cultural sensibility, stewardship, empowerment,
authenticity, reinforcement, and creativity. The question that remains
unanswered and essentially unresolved is how to explain the irony
that leaders are so much alike yet their organizations diverge so
noticeably in their ability to innovate. Leadership intersects with
innovation at the point where human interactions get exceedingly
complex and where certain paradoxical forces cohabit: conflict with
conciliation, sovereignty with interdependence, and imagination with
realism. Rather than accepting that leadership is without context, we
argue that leaders are specialists of their domain and that those
effective at leading for innovation are distinct within the broader pool
of leaders. Keeping in view the extensive literature on leadership and
innovation, we carried out a quantitative study with data collected
over a five-year period involving 240 participants from across five
dissimilar companies based in the United States. We found that while
innovation and leadership are, in general, strongly interrelated (r =
.89, p = 0.0), there are five qualities that set leaders apart on
innovation. These qualities include a large radius of trust, a restless
curiosity with a low need for acceptance, an honest sense of self and
other, a sense for knowledge and creativity as the yin and yang of
innovation, and an ability to use multiple senses in the engagement
with followers. When these particular behaviors and characteristics
are present in leaders, organizations out-innovate their rivals by a
margin of 29.3 per cent to gain an unassailable edge in a business
environment that is regularly disruptive. A strategic outcome of this
study is a psychometric scale named iLeadership, proposed with the
underlying evidence, limitations, and potential for leadership and
innovation in organizations.c
Abstract: This paper presents a new meta-heuristic bio-inspired
optimization algorithm which is called Cuttlefish Algorithm (CFA).
The algorithm mimics the mechanism of color changing behavior of
the cuttlefish to solve numerical global optimization problems. The
colors and patterns of the cuttlefish are produced by reflected light
from three different layers of cells. The proposed algorithm considers
mainly two processes: reflection and visibility. Reflection process
simulates light reflection mechanism used by these layers, while
visibility process simulates visibility of matching patterns of the
cuttlefish. To show the effectiveness of the algorithm, it is tested with
some other popular bio-inspired optimization algorithms such as
Genetic Algorithms (GA), Particle Swarm Optimization (PSO) and
Bees Algorithm (BA) that have been previously proposed in the
literature. Simulations and obtained results indicate that the proposed
CFA is superior when compared with these algorithms.
Abstract: Three dimensional non-Interlaced carbon fibre
reinforced silicon carbide (3-D-Cf/SiC) composites with pyrocarbon
interphase were fabricated using isothermal chemical vapor
infiltration (ICVI) combined with polymer impregnation pyrolysis
(PIP) process. Polysilazane (PSZ) is used as a preceramic polymer to
obtain silicon carbide matrix. Thermo gravimetric analysis (TGA),
Infrared spectroscopic analysis (IR) and X-ray diffraction (XRD)
analysis were carried out on PSZ pyrolysed at different temperatures
to understand the pyrolysis and obtaining the optimum pyrolysing
condition to yield β-SiC phase. The density of the composites was
1.94 g cm-3 after the 3-D carbon preform was SiC infiltrated for 280 h
with one intermediate polysilazane pre-ceramic PIP process.
Mechanical properties of the composite materials were investigated
under tensile, flexural, shear and impact loading. The values of
tensile strength were 200 MPa at room temperature (RT) and 195
MPa at 500°C in air. The average RT flexural strength was 243 MPa.
The lower flexural strength of these composites is because of the
porosity. The fracture toughness obtained from single edge notched
beam (SENB) technique was 39 MPa.m1/2. The work of fracture
obtained from the load-displacement curve of SENB test was 22.8
kJ.m-2. The composites exhibited excellent impact resistance and the
dynamic fracture toughness of 44.8 kJ.m-2 is achieved as determined
from instrumented Charpy impact test. The shear strength of the
composite was 93 MPa, which is significantly higher compared 2-D
Cf/SiC composites. Microstructure evaluation of fracture surfaces
revealed the signatures of fracture processes and showed good
support for the higher toughness obtained.
Abstract: This study aimed at designing and developing a
mechanical force gauge for the square watermelon mold for the first
time. It also tried to introduce the square watermelon characteristics
and its production limitations. The mechanical force gauge
performance and the product itself were also described. There are
three main designable gauge models: a. hydraulic gauge, b. strain
gauge, and c. mechanical gauge. The advantage of the hydraulic
model is that it instantly displays the pressure and thus the force
exerted by the melon. However, considering the inability to measure
forces at all directions, complicated development, high cost, possible
hydraulic fluid leak into the fruit chamber and the possible influence
of increased ambient temperature on the fluid pressure, the
development of this gauge was overruled. The second choice was to
calculate pressure using the direct force a strain gauge. The main
advantage of these strain gauges over spring types is their high
precision in measurements; but with regard to the lack of conformity
of strain gauge working range with water melon growth, calculations
were faced with problems. Finally the mechanical pressure gauge has
advantages, including the ability to measured forces and pressures on
the mold surface during melon growth; the ability to display the peak
forces; the ability to produce melon growth graph thanks to its
continuous force measurements; the conformity of its manufacturing
materials with the required physical conditions of melon growth; high
air conditioning capability; the ability to permit sunlight reaches the
melon rind (no yellowish skin and quality loss); fast and
straightforward calibration; no damages to the product during
assembling and disassembling; visual check capability of the product
within the mold; applicable to all growth environments (field,
greenhouses, etc.); simple process; low costs and so forth.
Abstract: This paper presents the performance state analysis of
Self-Excited Induction Generator (SEIG) using Artificial Bee Colony
(ABC) optimization technique. The total admittance of the induction
machine is minimized to calculate the frequency and magnetizing
reactance corresponding to any rotor speed, load impedance and
excitation capacitance. The performance of SEIG is calculated using
the optimized parameter found. The results obtained by ABC
algorithm are compared with results from numerical method. The
results obtained coincide with the numerical method results. This
technique proves to be efficient in solving nonlinear constrained
optimization problems and analyzing the performance of SEIG.
Abstract: Web search engines are designed to retrieve and
extract the information in the web databases and to return dynamic
web pages. The Semantic Web is an extension of the current web in
which it includes semantic content in web pages. The main goal of
semantic web is to promote the quality of the current web by
changing its contents into machine understandable form. Therefore,
the milestone of semantic web is to have semantic level information
in the web. Nowadays, people use different keyword- based search
engines to find the relevant information they need from the web.
But many of the words are polysemous. When these words are
used to query a search engine, it displays the Search Result Records
(SRRs) with different meanings. The SRRs with similar meanings are
grouped together based on Word Sense Disambiguation (WSD). In
addition to that semantic annotation is also performed to improve the
efficiency of search result records. Semantic Annotation is the
process of adding the semantic metadata to web resources. Thus the
grouped SRRs are annotated and generate a summary which
describes the information in SRRs. But the automatic semantic
annotation is a significant challenge in the semantic web. Here
ontology and knowledge based representation are used to annotate
the web pages.
Abstract: This paper is concerned with the stability problem
with two additive time-varying delay components. By choosing one
augmented Lyapunov-Krasovskii functional, using some new zero
equalities, and combining linear matrix inequalities (LMI)
techniques, two new sufficient criteria ensuring the global stability
asymptotic stability of DNNs is obtained. These stability criteria are
present in terms of linear matrix inequalities and can be easily
checked. Finally, some examples are showed to demonstrate the
effectiveness and less conservatism of the proposed method.
Abstract: Male factor infertility due to endocrine disturbances
such as abnormalities in prolactin levels are encountered in a
significant proportion. This case control study was carried out to
determine the effects of prolactin on the male reproductive tract,
using 200 male white rats. The rats were maintained as the control
group (G1), hypoprolactinaemic group (G2), 3 hyperprolactinaemic
groups induced using oral largactil (G3), low dose fluphenazine (G4)
and high dose fluphenazine (G5). After 100 days, rats were subjected
to serum prolactin (PRL) level measurements and for basic seminal
fluid analysis (BSA). The difference between serum PRL
concentrations of rats in G2, G3, G4 and G5 as compared to the
control group were highly significant by Student’s t-test (p
Abstract: The purposes of this research were to study concepts
and strategies of human resource development in the automotive
manufacturers and to articulate the proposals against the government
about the human resource development for automotive industry. In
the present study, qualitative study was an in-depth interview in
which the qualitative data were collected from the executive or the
executive of human resource division from five automotive
companies - Toyota Motor (Thailand) Co., Ltd., Nissan Motor
(Thailand) Co., Ltd., Mitsubishi Motors (Thailand) Co., Ltd., Honda
Automobile (Thailand) Co., Ltd., and Suzuki Motor (Thailand) Co.,
Ltd. Qualitative data analysis was performed by using inter-coder
agreement technique. The research findings were as follows:
The external factors included the current conditions of the
automotive industry, government’s policy related to the automotive
industry, technology, labor market and human resource development
systems of the country. The internal factors included management,
productive management, organizational strategies, leadership,
organizational culture and philosophy of human resource
development. These factors were affected to the different concept of
human resources development -the traditional human resource
development and the strategies of human resource development. The
organization focuses on human resources as intellectual capital and
uses the strategies of human resource development in all
development processes. The strategies of human resource
development will enhance the ability of human resources in the
organization and the country.
Abstract: Concerns on corrosion and effective coating
protection of double hull tankers and bulk carriers in service have
been raised especially in water ballast tanks (WBTs). Test
protocols/methodologies specifically that which is incorporated in the
International Maritime Organisation (IMO), Performance Standard
for Protective Coatings for Dedicated Sea Water ballast tanks (PSPC)
are being used to assess and evaluate the performance of the coatings
for type approval prior to their application in WBTs. However, some
of the type approved coatings may be applied as very thick films to
less than ideally prepared steel substrates in the WBT. As such films
experience hygrothermal cycling from operating and environmental
conditions, they become embrittled which may ultimately result in
cracking. This embrittlement of the coatings is identified as an
undesirable feature in the PSPC but is not mentioned in the test
protocols within it. There is therefore renewed industrial research
aimed at understanding this issue in order to eliminate cracking and
achieve the intended coating lifespan of 15 years in good condition.
This paper will critically review test protocols currently used for
assessing and evaluating coating performance, particularly the IMO
PSPC.
Abstract: Lightning protection systems (LPS) for wind power
generation is becoming an important public issue. A serious damage
of blades, accidents where low-voltage and control circuit
breakdowns are frequently occur in many wind farms. A grounding
system is one of the most important components required for
appropriate LPSs in wind turbines WTs. Proper design of a wind
turbine grounding system is demanding and several factors for the
proper and effective implementation must taken into account. In this
paper proposed procedure of proper design of grounding systems for
a wind turbine was introduced. This procedure depends on measuring
of ground current of simulated wind farm under lightning taking into
consideration the soil ionization. The procedure also includes the
Ground Potential Rise (GPR) and the voltage distributions at ground
surface level and Touch potential. In particular, the contribution of
mitigating techniques, such as rings, rods and the proposed design
were investigated.
Abstract: The growth of wireless devices affects the availability
of limited frequencies or spectrum bands as it has been known that
spectrum bands are a natural resource that cannot be added.
Meanwhile, the licensed frequencies are idle most of the time.
Cognitive radio is one of the solutions to solve those problems.
Cognitive radio is a promising technology that allows the unlicensed
users known as secondary users (SUs) to access licensed bands
without making interference to licensed users or primary users (PUs).
As cloud computing has become popular in recent years, cognitive
radio networks (CRNs) can be integrated with cloud platform. One of
the important issues in CRNs is security. It becomes a problem since
CRNs use radio frequencies as a medium for transmitting and CRNs
share the same issues with wireless communication systems. Another
critical issue in CRNs is performance. Security has adverse effect to
performance and there are trade-offs between them. The goal of this
paper is to investigate the performance related to security trade-off in
CRNs with supporting cloud platforms. Furthermore, Queuing
Network Models with preemptive resume and preemptive repeat
identical priority are applied in this project to measure the impact of
security to performance in CRNs with or without cloud platform. The
generalized exponential (GE) type distribution is used to reflect the
bursty inter-arrival and service times at the servers. The results show
that the best performance is obtained when security is disabled and
cloud platform is enabled.
Abstract: This paper presents the design and analysis of Liquid
Crystal (LC) based tunable reflectarray antenna with different design
configurations within X-band frequency range. The effect of LC
volume used for unit cell element on frequency tunability and
reflection loss performance has been investigated. Moreover different
slot embedded patch element configurations have been proposed for
LC based tunable reflectarray antenna design with enhanced
performance. The detailed fabrication and measurement procedure
for different LC based unit cells has been presented. The waveguide
scattering parameter measured results demonstrated that by using the
circular slot embedded patch elements, the frequency tunability and
dynamic phase range can be increased from 180MHz to 200MHz and
120° to 124° respectively. Furthermore the circular slot embedded
patch element can be designed at 10GHz resonant frequency with a
patch volume of 2.71mm3 as compared to 3.47mm3 required for
rectangular patch without slot.
Abstract: Despite four years of study in the tourism industry, the
Bachelor’s graduates cannot perform their jobs as experienced tour
guides. This research aimed to develop French teaching and studying
for Tourism with two main purposes: to analyze ‘Moves’ used in oral
presentations at tourist attraction; and to study content in guiding
presentations or 'Guide Speak'. The study employed audio recording
of these presentations as an interview method in authentic situations,
having four tour guides as respondents and information providers.
The data was analyzed via moves and content analysis. The results
found that there were eight Moves used; namely, Welcoming,
Introducing oneself, Drawing someone’s attention, Giving
information, Explaining, Highlighting, Persuading and Saying
goodbye. In terms of content, the information being presented
covered the outstanding characteristics of the places and wellintegrated
with other related content. The findings were used as
guidelines for curriculum development; in particular, the core content
and the presentation forming the basis for students to meet the
standard requirements of the labor-market and professional schemes.
Abstract: This paper presents the voltage problem location
classification using performance of Least Squares Support Vector
Machine (LS-SVM) and Learning Vector Quantization (LVQ) in
electrical power system for proper voltage problem location
implemented by IEEE 39 bus New- England. The data was collected
from the time domain simulation by using Power System Analysis
Toolbox (PSAT). Outputs from simulation data such as voltage, phase
angle, real power and reactive power were taken as input to estimate
voltage stability at particular buses based on Power Transfer Stability
Index (PTSI).The simulation data was carried out on the IEEE 39 bus
test system by considering load bus increased on the system. To verify
of the proposed LS-SVM its performance was compared to Learning
Vector Quantization (LVQ). The results showed that LS-SVM is faster
and better as compared to LVQ. The results also demonstrated that the
LS-SVM was estimated by 0% misclassification whereas LVQ had
7.69% misclassification.
Abstract: In Egypt, girls have traditionally been educationally
disadvantaged. This disadvantage, however, has been focused on the
failure to enter school. Increasingly it is recognized that girls who
ever-enroll are at least as likely to complete primary and secondary
education as boys. Still the belief persists that girls, especially those
from poor families, will be disadvantaged in terms of school
expenditures and the transitions to secondary and higher education.
We examine expenditures on tutoring during the final year of
preparatory school, and the transition to specific tracks of secondary
education. Tests during the last year of preparatory largely determine
a student’s educational future. Results show that girls, even girls from
poor families, are not disadvantaged in terms of expenditures,
whether for tutoring, fees or general expenses. Moreover, girls are
more likely than boys to advance to general secondary education, the
track that leads to higher education.
Abstract: A blood pressure monitor or sphygmomanometer can
be either manual or automatic, employing respectively either the
auscultatory method or the oscillometric method.
The manual version of the sphygmomanometer involves an
inflatable cuff with a stethoscope adopted to detect the sounds
generated by the arterial walls to measure blood pressure in an artery.
An automatic sphygmomanometer can be effectively used to
monitor blood pressure through a pressure sensor, which detects
vibrations provoked by oscillations of the arterial walls.
The pressure sensor implemented in this device improves the
accuracy of the measurements taken.