Abstract: This paper presents effects of the mean operating
pressure on the optimal operating frequency based on temperature
differences across stack ends in a thermoacoustic refrigerator. In
addition to the length of the resonance tube, components of the
thermoacoustic refrigerator have an influence on the operating
frequency due to their acoustic properties, i.e., absorptivity,
reflectivity and transmissivity. The interference of waves incurs and
distorts the original frequency generated by the driver so that the
optimal operating frequency differs from the designs. These acoustic
properties are not parameters in the designs and be very complicated
to infer their responses. A prototype thermoacoustic refrigerator is
constructed and used to investigate its optimal operating frequency
compared to the design at various operating pressures. Helium and air
are used as working fluids during the experiments. The results
indicate that the optimal operating frequency of the prototype
thermoacoustic refrigerator using helium is at 6 bar and 490Hz or
approximately 20% away from the design frequency. The optimal
operating frequency at other mean pressures differs from the design
in an unpredictable manner, however, the optimal operating
frequency and pressure can be identified by testing.
Abstract: A cold, thin film of liquid impinging on an isothermal
hot, horizontal surface has been investigated. An approximate
solution for the velocity and temperature distributions in the flow
along the horizontal surface is developed, which exploits the
hydrodynamic similarity solution for thin film flow. The approximate
solution may provide a valuable basis for assessing flow and heat
transfer in more complex settings.
Abstract: This paper presents dynamic models of distributed
generators (DG) and investigates dynamic behavior of the DG units
in the micro grid system. The DG units include photovoltaic and fuel
cell sources. The voltage source inverter is adopted since the
electronic interface which can be equipped with its controller to keep
stability of the micro grid during small signal dynamics. This paper
also introduces power management strategies and implements the DG
load sharing concept to keep the micro grid operation in gridconnected
and islanding modes of operation. The results demonstrate
the operation and performance of the photovoltaic and fuel cell as
distributed generators in a micro grid. The entire control system in
the micro grid is developed by combining the benefits of the power
control and the voltage control strategies. Simulation results are all
reported, confirming the validity of the proposed control technique.
Abstract: The thermal performance of a solar water heating with
1.00 m2 flat plate collectors in Cascavel - PR, is which presented in
this article, paper presents the solution to leverage the marketing of
solar heating systems through detailed constituent materials of the
solar collector studies, these abundant materials in construction, such
as expanded polyethylene, PVC, aluminum and glass tubes, mixing
them with new materials to minimize loss of efficiency while
decreasing its cost. The system was tested during months and the
collector obtained maximum recorded temperature of outlet fluid of
55°C, while the maximum temperature of the water at the bottom of
the hot water tank was 35°C. The average daily energy collected was
19.6 MJ/d; the energy supplied by the solar plate was 16.2 MJ/d; the
loss in the feed pipe was 3.2 MJ/d; the solar fraction was 32.2%, the
efficiency of the collector was 45.6% and the efficiency of the system
was 37.8%.
Abstract: Honeys are produced by Apis mellifera and stingless
bees (Meliponini) in Ecuador. We studied honey produced in
beeswax combs by Apis mellifera, and honey produced in pots by
Geotrigona and Scaptotrigona bees. Chloroform extracts of honey
were obtained for fast NMR spectra. The 1D spectra were acquired at
298 K, with a 600 MHz NMR Bruker instrument, using a modified
double pulsed field gradient spin echoes (DPFGSE) sequence.
Signals of 1H NMR spectra were integrated and used as inputs for
PCA, PLS-DA analysis, and labelled sets of classes were successfully
identified, enhancing the separation between the three groups of
honey according to the entomological origin: A. mellifera,
Geotrigona and Scaptotrigona. This procedure is therefore
recommended for authenticity test of honey in Ecuador.
Abstract: In this research the effect of moisture at three levels
(47, 57, and 67 w.b.%) on the physical properties of the Pofaki pea
variety including, dimensions, geometric mean diameter, volume,
sphericity index and the surface area was determined. The influence
of different moisture levels (47, 57 and 67 w.b.%), in two loading
orientation (longitudinal and transverse) and three loading speed (4,6
and 8 mm min-1) on the mechanical properties of pea such as
maximum deformation, rupture force, rupture energy, toughness and
the power to break the pea was investigated. It was observed in the
physical properties that moisture changes were affective at 1% on,
dimensions, geometric mean diameter, volume, sphericity index and
the surface area. It was observed in the mechanical properties that
moisture changes were effective at 1% on, maximum deformation,
rupture force, rupture energy, toughness and the power to break.
Loading speed was effective on maximum deformation, rupture
force, rupture energy at 1% and it was effective on toughness at 5%.
Loading orientation was effective on maximum deformation, rupture
force, rupture energy, toughness at 1% and it was effective on power
at 5%. The mutual effect of speed and orientation were effective on
rupture energy at 1% and were effective on toughness at 5%
probability. The mutual effect of moisture and speed were effective
on rupture force and rupture energy at 1% and were effective on
toughness 5% probability. The mutual effect of orientation and
moisture on rupture energy and toughness were effective at 1%.
Abstract: This paper deals with the theoretical and numerical
investigation of magneto hydrodynamic boundary layer flow of a
nanofluid past a wedge shaped wick in heat pipe used for the cooling
of electronic components and different type of machines. To
incorporate the effect of nanoparticle diameter, concentration of
nanoparticles in the pure fluid, nanothermal layer formed around the
nanoparticle and Brownian motion of nanoparticles etc., appropriate
models are used for the effective thermal and physical properties of
nanofluids. To model the rotation of nanoparticles inside the base
fluid, microfluidics theory is used. In this investigation ethylene
glycol (EG) based nanofluids, are taken into account. The non-linear
equations governing the flow and heat transfer are solved by using a
very effective particle swarm optimization technique along with
Runge-Kutta method. The values of heat transfer coefficient are
found for different parameters involved in the formulation viz.
nanoparticle concentration, nanoparticle size, magnetic field and
wedge angle etc. It is found that, the wedge angle, presence of
magnetic field, nanoparticle size and nanoparticle concentration etc.
have prominent effects on fluid flow and heat transfer characteristics
for the considered configuration.
Abstract: This paper presents a study the effect of nose radius
(Rz-mm) on cutting force components and temperatures during the
machining simulation in an orthogonal cutting process for titanium
alloy (Ti-6Al-4V). The cutting process was performed at various
nose radiuses (Rz-mm) while the depth of cut (d-mm), feed rate (fmm/
tooth) and cutting speed (vc-m/ min) were remained constant.
The main cutting force (Fc), feed cutting force (Ft) and temperatures
were estimated by using finite element modeling (FEM) through
ABAQUS/EXPLICIT software and the simulation was developed the
two-dimension via an orthogonal cutting process during machining
titanium alloy (Ti-6Al-4V). The results led to the conclusion that the
nose radius (Rz-mm) has affected directly on the cutting force
components. However, temperature gave no indication or has no
significant relation with nose radius during machining titanium alloy
(Ti-6Al-4V). Hence, any increase or decrease in the nose radius (Rzmm)
during machining operation led to effect on the cutting forces
and thus it will be effective on surface finish, quality, and quantity of
products.
Abstract: In emerging economies, recycling is an opportunity
for the cities to increase the lifespan of sanitary landfills, reduce the
costs of the solid waste management, decrease the environmental
problems of the waste treatment through reincorporate waste in the
productive cycle and protect and develop people’s livelihoods of
informal waste pickers. However, few studies have analysed the
possibilities and strategies to integrate formal and informal sectors in
the solid waste management for the benefit of both. This study seek
to make a strength, weakness, opportunity, and threat (SWOT)
analysis in three recycling associations of Bogotá with the aim to
understand and determine the situation of recycling from perspective
of informal sector in its transition to enter as authorized waste
providers. Data used in the analysis are derived from multiple
strategies such as literature review, the Bogota’s recycling database,
focus group meetings, governmental reports, national laws and
regulations and specific interviews with key stakeholders. Results of
this study show as the main stakeholders of formal and informal
sector of waste management can identify the internal and internal
conditions of recycling in Bogotá. Several strategies were designed
based on the SWOTs determined, could be useful for Bogotá to
advance and promote recycling as a key strategy for integrated
sustainable waste management in the city.
Abstract: An innovative flooring underlayment was produced
and tested. The composite system is made of common OSB boards
and a layer of eco-friendly non-cement gypsum based material
(GeoGypTM). It was found that the shear bond between the two
materials is sufficient to secure the composite interaction between the
two. The very high compressive strength and relatively high tensile
strength of the non-cement based component together with its high
modulus of elasticity provides enough strength and stiffness for the
composite product to cover wider spacing between the joists. The
initial findings of this study indicate that with joist spacing as wide as
800 mm, the flooring system provides enough strength without
compromising the serviceability requirements of the building codes.
Abstract: Scrubbing by a liquid spraying is one of the most
effective processes used for removal of fine particles and soluble
gas pollutants (such as SO2, HCl, HF) from the flue gas. There are
many configurations of scrubbers designed to provide contact
between the liquid and gas stream for effectively capturing
particles or soluble gas pollutants, such as spray plates, packed bed
towers, jet scrubbers, cyclones, vortex and venturi scrubbers. The
primary function of venturi scrubber is the capture of fine particles
as well as HCl, HF or SO2 removal with effect of the flue gas
temperature decrease before input to the absorption column. In this
paper, sulfur dioxide (SO2) from flue gas was captured using new
design replacing venturi scrubber (1st degree of wet scrubbing).
The flue gas was prepared by the combustion of the carbon
disulfide solution in toluene (1:1 vol.) in the flame in the reactor.
Such prepared flue gas with temperature around 150°C was
processed in designed laboratory O-element scrubber. Water was
used as absorbent liquid. The efficiency of SO2 removal, pressure
drop and temperature drop were measured on our experimental
device. The dependence of these variables on liquid-gas ratio was
observed. The average temperature drop was in the range from
150°C to 40°C. The pressure drop was increased with increasing of
a liquid-gas ratio, but no too much as for the common venturi
scrubber designs. The efficiency of SO2 removal was up to 70 %.
The pressure drop of our new designed wet scrubber is similar to
commonly used venturi scrubbers; nevertheless the influence of
amount of the liquid on pressure drop is not so significant.
Abstract: This paper is concerned with knowledge representation
and extraction of fuzzy if-then rules using Interval Type-2
Context-based Fuzzy C-Means clustering (IT2-CFCM) with the aid of
fuzzy granulation. This proposed clustering algorithm is based on
information granulation in the form of IT2 based Fuzzy C-Means
(IT2-FCM) clustering and estimates the cluster centers by preserving
the homogeneity between the clustered patterns from the IT2 contexts
produced in the output space. Furthermore, we can obtain the
automatic knowledge representation in the design of Radial Basis
Function Networks (RBFN), Linguistic Model (LM), and Adaptive
Neuro-Fuzzy Networks (ANFN) from the numerical input-output data
pairs. We shall focus on a design of ANFN in this paper. The
experimental results on an estimation problem of energy performance
reveal that the proposed method showed a good knowledge
representation and performance in comparison with the previous
works.
Abstract: This paper presents a part of the project solving which
is dedicated to the identification of the hazardous waste with the most
critical production within the Czech Republic with the aim to study
and find the optimal composition of the cement matrix that will
ensure maximum content disposal of chosen hazardous waste. In the
first stage of project solving – which represents this paper – a specific
hazardous waste was chosen, its properties were identified and
suitable solidification agents were chosen. Consequently
solidification formulas and testing methodology was proposed.
Abstract: Moving into a new era of healthcare, new tools and
devices are developed to extend and improve health services, such as
remote patient monitoring and risk prevention. In this concept,
Internet of Things (IoT) and Cloud Computing present great
advantages by providing remote and efficient services, as well as
cooperation between patients, clinicians, researchers and other health
professionals. This paper focuses on patients suffering from bipolar
disorder, a brain disorder that belongs to a group of conditions
called affective disorders, which is characterized by great mood
swings. We exploit the advantages of Semantic Web and Cloud
Technologies to develop a patient monitoring system to support
clinicians. Based on intelligently filtering of evidence-knowledge and
individual-specific information we aim to provide treatment
notifications and recommended function tests at appropriate times or
concluding into alerts for serious mood changes and patient’s nonresponse
to treatment. We propose an architecture as the back-end
part of a cloud platform for IoT, intertwining intelligence devices
with patients’ daily routine and clinicians’ support.
Abstract: Reliability of long-term storage products is related to
the availability of the whole system, and the evaluation of storage life
is of great necessity. These products are usually highly reliable and
little failure information can be collected. In this paper, an analytical
method based on data from accelerated storage life test is proposed to
evaluate the reliability index of the long-term storage products. Firstly,
singularities are eliminated by data normalization and residual
analysis. Secondly, with the preprocessed data, the degradation path
model is built to obtain the pseudo life values. Then by life distribution
hypothesis, we can get the estimator of parameters in high stress levels
and verify failure mechanism consistency. Finally, the life distribution
under the normal stress level is extrapolated via the acceleration model
and evaluation of the actual average life is available. An application
example with the camera stabilization device is provided to illustrate
the methodology we proposed.
Abstract: We have conducted the optimal synthesis of rootmean-
squared objective filter to estimate the state vector in the case if
within the observation channel with memory the anomalous noises
with unknown mathematical expectation are complement in the
function of the regular noises. The synthesis has been carried out for
linear stochastic systems of continuous - time.
Abstract: We investigate relaxation dynamics of a quantum
dipole emitter (QDE), e.g., a molecule or quantum dot, located near a
metal nanoparticle (MNP) exhibiting a dipolar localized surface
plasmon (LSP) resonance at the frequency of the QDE radiative
transition. It is shown that under the condition of the QDE-MNP
characteristic relaxation time being much shorter than that of the
QDE in free-space but much longer than the LSP lifetime. It is also
shown that energy dissipation in the QDE-MNP system is relatively
weak with the probability of the photon emission being about 0.75, a
number which, rather surprisingly, does not explicitly depend on the
metal absorption characteristics. The degree of entanglement
measured by the concurrency takes the maximum value, while the
distances between the QDEs and metal ball approximately are equal.
Abstract: Early diagnosis of infection like Hep-B virus in blood
is important for low cost medical treatment. For this purpose, it is
desirable to develop a point of care device which should be able to
detect trace quantities of the target molecule in blood. In this paper,
we report a nanoporous silicon oxide sensor which is capable of
detecting down to 1fM concentration of Hep-B surface antigen in
blood without the requirement of any centrifuge or pre-concentration.
This has been made possible by the presence of resonant peak in the
sensitivity characteristics. This peak is observed to be dependent only
on the concentration of the specific antigen and not on the interfering
species in blood serum. The occurrence of opposite impedance
change within the pores and at the bottom of the pore is responsible
for this effect. An electronic interface has also been designed to
provide a display of the virus concentration.
Abstract: Testability modeling is a commonly used method in
testability design and analysis of system. A dependency matrix will be
obtained from testability modeling, and we will give a quantitative
evaluation about fault detection and isolation.
Based on the dependency matrix, we can obtain the diagnosis tree.
The tree provides the procedures of the fault detection and isolation.
But the dependency matrix usually includes built-in test (BIT) and
manual test in fact. BIT runs the test automatically and is not limited
by the procedures. The method above cannot give a more efficient
diagnosis and use the advantages of the BIT.
A Comprehensive method of fault detection and isolation is
proposed. This method combines the advantages of the BIT and
Manual test by splitting the matrix. The result of the case study shows
that the method is effective.
Abstract: Propylene self-metathesis to ethylene and butene was
studied over WOx/SiO2 catalysts at 450oC and atmospheric pressure.
The WOx/SiO2 catalysts were prepared by incipient wetness
impregnation of ammonium metatungstate aqueous solution. It was
found that, adding nano-sized extra supports (SiO2 and TiO2) by
physical mixing with the WOx/SiO2 enhanced propylene conversion.
The UV-Vis and FT-Raman results revealed that WOx could migrate
from the original silica support to the extra support, leading to a
better dispersion of WOx. The ICP-OES results also indicate that
WOx existed on the extra support. Coke formation was investigated
on the catalysts after 10 h time-on-stream by TPO. However, adding
nano-sized extra supports led to higher coke formation which may be
related to acidity as characterized by NH3-TPD.