Abstract: Continuous upflow filters can combine the nutrient
(nitrogen and phosphate) and suspended solid removal in one unit
process. The contaminant removal could be achieved chemically or
biologically; in both processes the filter removal efficiency depends
on the interaction between the packed filter media and the influent. In
this paper a residence time distribution (RTD) study was carried out
to understand and compare the transfer behaviour of contaminants
through a selected filter media packed in a laboratory-scale
continuous up flow filter; the selected filter media are limestone and
white dolomite. The experimental work was conducted by injecting a
tracer (red drain dye tracer –RDD) into the filtration system and then
measuring the tracer concentration at the outflow as a function of
time; the tracer injection was applied at hydraulic loading rates
(HLRs) (3.8 to 15.2 m h-1). The results were analysed according to
the cumulative distribution function F(t) to estimate the residence
time of the tracer molecules inside the filter media. The mean
residence time (MRT) and variance σ2 are two moments of RTD that
were calculated to compare the RTD characteristics of limestone with
white dolomite. The results showed that the exit-age distribution of
the tracer looks better at HLRs (3.8 to 7.6 m h-1) and (3.8 m h-1) for
limestone and white dolomite respectively. At these HLRs the
cumulative distribution function F(t) revealed that the residence time
of the tracer inside the limestone was longer than in the white
dolomite; whereas all the tracer took 8 minutes to leave the white
dolomite at 3.8 m h-1. On the other hand, the same amount of the
tracer took 10 minutes to leave the limestone at the same HLR. In
conclusion, the determination of the optimal level of hydraulic
loading rate, which achieved the better influent distribution over the
filtration system, helps to identify the applicability of the material as
filter media. Further work will be applied to examine the efficiency
of the limestone and white dolomite for phosphate removal by
pumping a phosphate solution into the filter at HLRs (3.8 to 7.6 m h-1).
Abstract: This article aims to analyze the static stability and
pseudostatic slope by using different methods such as: Bishop
method, Junbu, Ordinary, Morgenstern-price and GLE. The two
dimensional modeling of slope stability under various loading as: the
earthquake effect, the water level and road mobile charges. The
results show that the slope is stable in the static case without water,
but in other cases, the slope lost its stability and give unstable. The
calculation of safety factor is to evaluate the stability of the slope
using the limit equilibrium method despite the difference between the
results obtained by these methods that do not rely on the same
assumptions. In the end, the results of this study illuminate well the
influence of the action of water, moving loads and the earthquake on
the stability of the slope.
Abstract: In recent years a new method of combination
treatment for cancer has been developed and studied that has led to
significant advancements in the field of cancer therapy. Hyperthermia
is a traditional therapy that, along with a creation of a medically
approved level of heat with the help of an alternating magnetic AC
current, results in the destruction of cancer cells by heat. This paper
gives details regarding the production of the spherical nanocomposite
PVA/γ-Fe2O3 in order to be used for medical purposes such as tumor
treatment by hyperthermia. To reach a suitable and evenly distributed
temperature, the nanocomposite with core-shell morphology and
spherical form within a 100 to 200 nanometer size was created using
phase separation emulsion, in which the magnetic nano-particles γ-
Fe2O3 with an average particle size of 20 nano-meters and with
different percentages of 0.2, 0.4, 0.5 and 0.6 were covered by
polyvinyl alcohol. The main concern in hyperthermia and heat
treatment is achieving desirable specific absorption rate (SAR) and
one of the most critical factors in SAR is particle size. In this project
all attempts has been done to reach minimal size and consequently
maximum SAR. The morphological analysis of the spherical
structure of the nanocomposite PVA/γ-Fe2O3 was achieved by SEM
analyses and the study of the chemical bonds created was made
possible by FTIR analysis. To investigate the manner of magnetic
nanocomposite particle size distribution a DLS experiment was
conducted. Moreover, to determine the magnetic behavior of the γ-
Fe2O3 particle and the nanocomposite PVA/γ-Fe2O3 in different
concentrations a VSM test was conducted. To sum up, creating
magnetic nanocomposites with a spherical morphology that would be
employed for drug loading opens doors to new approaches in
developing nanocomposites that provide efficient heat and a
controlled release of drug simultaneously inside the magnetic field,
which are among their positive characteristics that could significantly
improve the recovery process in patients.
Abstract: This paper presents an experimental study on
structural performance of an innovative noise barrier consisting of
poly-block, light polyurethane foam (LPF) and polyurea. This wall
system (flexi-wall) is intended to be employed as a vertical extension
to existing sound barriers in an accelerated construction method. To
aid in the wall design, several mechanical tests were conducted on
LPF specimens and two full-scale walls were then fabricated
employing the same LPF material. The full-scale walls were
subjected to lateral loading in order to establish their lateral
resistance. A cyclic fatigue test was also performed on a full-scale
flexi-wall in order to evaluate the performance of the wall under a
repetitive loading condition. The result of the experiments indicated
the suitability of flexi-wall in accelerated construction and confirmed
that the structural performance of the wall system under lateral
loading is satisfactory for the sound barrier application. The
experimental results were discussed and a preliminary design
procedure for application of flexi-wall in sound barrier applications
was also developed.
Abstract: Hemoglobin (HB) indicates anemia level and by
extension may reflect the nutritional level and perhaps the immunity
of an individual. Some antiretroviral drugs like Zidovudine are
known to cause anemia in people living with HIV/AIDS (PLWHA).
A cross sectional study using demographic data and blood specimen
from 218 female commercial sex workers attending antiretroviral
therapy (ART) clinics was conducted between December, 2009 and
July, 2011 to assess the effect of zidovudine on hematologic, and
RNA viral load of female sex workers receiving antiretroviral
treatment in north western Nigeria. Anemia is a common and serious
complication of both HIV infection and its treatment. In the setting of
HIV infection, anemia has been associated with decreased quality of
life, functional status, and survival. Antiretroviral therapy,
particularly the highly active antiretroviral therapy (HAART), has
been associated with a decrease in the incidence and severity of
anemia in HIV-infected patients who have received a HAART
regimen for at least 1 year. In this study, result has shown that of the
218 patients, 26 with hemoglobin count between 5.1 – 10g/dl were
observed to have the highest viral load count of 300,000 –
350,000copies/ml. It was also observed that most patients (190) with
HB of 10.1 – 15.0g/dl had viral load count of 200,000 – 250,000
copies /ml. An inverse relationship therefore exists i.e. the lower the
hemoglobin level, the higher the viral load count even though the test
statistics did not show any significance between the two (P = 0.206).
This shows that multivariate logistic regression analysis
demonstrated that anemia was associated with a CD4 + cell count
below 50/μL, female sex workers with a viral load above 100,000
copies/mL, who use zidovudine.
Severe anemia was less prevalent in this study population than in
historical comparators; however, mild to moderate anemia rates
remain high. The study therefore recommends that hematological and
virologic parameters be monitored closely in patients receiving first
line ART regimen.
Abstract: We report herein the development and preliminary mechanical characterization of fully-dense multi-wall carbon nanotube (MWCNT)-reinforced ceramics and glasses based on a completely new methodology termed High Shear Compaction (HSC). The tubes are introduced and bound to the matrix grains by aid of polymeric binders to form flexible green bodies which are sintered and densified by spark plasma sintering to unprecedentedly high densities of 100% of the pure-matrix value. The strategy was validated across a PyrexTM glass / MWCNT composite while no identifiable factors limit application to other types of matrices. Nondestructive evaluation, based on ultrasonics, of the dynamic mechanical properties of the materials including elastic, shear and bulk modulus as well as Poisson’s ratio showed optimum property improvement at 0.5 %wt tube loading while evidence of nanoscalespecific energy dissipative characteristics acting complementary to nanotube bridging and pull-out indicate a high potential in a wide range of reinforcing and multifunctional applications.
Abstract: Supply chains are the backbone of trade and
commerce. Their logistics use different transport corridors on regular
basis for operational purpose. The international supply chain
transport corridors include different infrastructure elements (e.g.
weighbridge, package handling equipments, border clearance
authorities, and so on). This paper presents the use of multi-agent
systems (MAS) to model and simulate some aspects of transportation
corridors, and in particular the area of weighbridge resource
optimization for operational profit. An underlying multi-agent model
provides a means of modeling the relationships among stakeholders
in order to enable coordination in a transport corridor environment.
Simulations of the costs of container unloading, reloading, and
waiting time for queuing up tracks have been carried out using data
sets. Results of the simulation provide the potential guidance in
making decisions about optimal service resource allocation in a trade
corridor.
Abstract: This research aims to develop an algorithm to
generate a schedule of multiple cranes that will maximize load
throughputs in anodizing operation. The algorithm proposed utilizes
an enumerative strategy to search for constant time between
successive loads and crane covering range over baths. The computer
program developed is able to generate a near-optimal crane schedule
within reasonable times, i.e. within 10 minutes. Its results are
compared with existing solutions from an aluminum extrusion
industry. The program can be used to generate crane schedules for
mixed products, thus allowing mixed-model line balancing to
improve overall cycle times.
Abstract: A sensory network consists of multiple detection
locations called sensor nodes, each of which is tiny, featherweight
and portable. A single path routing protocols in wireless sensor
network can lead to holes in the network, since only the nodes
present in the single path is used for the data transmission. Apart
from the advantages like reduced computation, complexity and
resource utilization, there are some drawbacks like throughput,
increased traffic load and delay in data delivery. Therefore, multipath
routing protocols are preferred for WSN. Distributing the traffic
among multiple paths increases the network lifetime. We propose a
scheme, for the data to be transmitted through a dominant path to
save energy. In order to obtain a high delivery ratio, a basic route
reconstruction protocol is utilized to reconstruct the path whenever a
failure is detected. A basic reconstruction routing (BRR) algorithm is
proposed, in which a node can leap over path failure by using the
already existing routing information from its neighbourhood while
the composed data is transmitted from the source to the sink. In order
to save the energy and attain high data delivery ratio, data is
transmitted along a multiple path, which is achieved by BRR
algorithm whenever a failure is detected. Further, the analysis of
how the proposed protocol overcomes the drawback of the existing
protocols is presented. The performance of our protocol is compared
to AOMDV and energy efficient node-disjoint multipath routing
protocol (EENDMRP). The system is implemented using NS-2.34.
The simulation results show that the proposed protocol has high
delivery ratio with low energy consumption.
Abstract: Nowadays, the use of renewable energy sources has been increasingly great because of the cost increase and public demand for clean energy sources. One of the fastest growing sources is wind energy. In this paper, Wind Diesel Hybrid System (WDHS) comprising a Diesel Generator (DG), a Wind Turbine Generator (WTG), the Consumer Load, a Battery-based Energy Storage System (BESS), and a Dump Load (DL) is used. Voltage is controlled by Diesel Generator; the frequency is controlled by BESS and DL. The BESS elimination is an efficient way to reduce maintenance cost and increase the dynamic response. Simulation results with graphs for the frequency of Power System, active power, and the battery power are presented for load changes. The controlling parameters are optimized by using Imperialist Competitive Algorithm (ICA). The simulation results for the BESS/no BESS cases are compared. Results show that in no BESS case, the frequency control is more optimal than the BESS case by using ICA.
Abstract: Knowledge of bone mechanical properties is important
for bone substitutes design and fabrication, and more efficient
prostheses development. The aim of this study is to characterize the
viscoelastic behavior of bone specimens, through stress relaxation
and fatigue tests performed to trabecular bone samples from bovine
femoral heads. Relaxation tests consisted on preloading the samples
at five different magnitudes and evaluate them for 1020 seconds,
adjusting the results to a KWW mathematical model. Fatigue tests
consisted of 700 load cycles and analyze their status at the end of the
tests. As a conclusion we have that between relaxation stress and
each preload there is linear relation and for samples with initial
Young´s modulus greater than 1.5 GPa showed no effects due fatigue
test loading cycles.
Abstract: This study was aimed to investigate the machining
stability of a spindle tool with different preloaded amount. To this end,
the vibration tests were conducted on the spindle unit with different
preload to assess the dynamic characteristics and machining stability
of the milling machine. Current results demonstrate that the tool tip
frequency response characteristics and the machining stabilities in X
and Y direction are affected to change due to the different preload of
spindle bearings. As found from the results, a high preloaded spindle
tool shows higher limited cutting depth at mid position, while a spindle
with low preload shows a higher limited depth. This indicates that the
machining stability of a milling machine is affected to vary by the
spindle unit when it was assembled with different bearing preload.
Abstract: Metal thin-walled members have been widely used in
building industry. Usually they are utilized as purlins, girts or ceiling
beams. Due to slenderness of thin-walled cross-sections these
structural members are prone to stability problems (e.g. flexural
buckling, lateral torsional buckling). If buckling is not
constructionally prevented their resistance is limited by buckling
strength. In practice planar members of roof or wall cladding can be
attached to thin-walled members. These elements reduce
displacement of thin-walled members and therefore increase their
buckling strength. If this effect is taken into static assessment more
economical sections of thin-walled members might be utilized and
certain savings of material might be achieved. This paper focuses on
problem of determination of critical load of steel thin-walled beams
with lateral continuous restraint which is crucial for lateral torsional
buckling assessment.
Abstract: The nanoindentation behaviour and phase
transformation of annealed single-crystal silicon wafers are examined.
The silicon specimens are annealed at temperatures of 250, 350 and
450ºC, respectively, for 15 minutes and are then indented to maximum
loads of 30, 50 and 70 mN. The phase changes induced in the indented
specimens are observed using transmission electron microscopy
(TEM) and micro-Raman scattering spectroscopy (RSS). For all
annealing temperatures, an elbow feature is observed in the unloading
curve following indentation to a maximum load of 30 mN. Under
higher loads of 50 mN and 70 mN, respectively, the elbow feature is
replaced by a pop-out event. The elbow feature reveals a complete
amorphous phase transformation within the indented zone, whereas
the pop-out event indicates the formation of Si XII and Si III phases.
The experimental results show that the formation of these crystalline
silicon phases increases with an increasing annealing temperature and
indentation load. The hardness and Young’s modulus both decrease as
the annealing temperature and indentation load are increased.
Abstract: This article proposes a new method for application in
communication circuit systems that increase efficiency, PAE, output
power and gain in the circuit. The proposed method is based on a
combination of switching class-E and class-J and has been termed
class-EJ. This method was investigated using both theory and
simulation to confirm ∼72% PAE and output power of >39dBm. The
combination and design of the proposed power amplifier accrues gain
of over 15dB in the 2.9 to 3.5GHz frequency bandwidth. This circuit
was designed using MOSFET and high power transistors. The loadand
source-pull method achieved the best input and output networks
using lumped elements. The proposed technique was investigated for
fundamental and second harmonics having desirable amplitudes for
the output signal.
Abstract: Among various active filters, shunt active filter is a
viable solution for reactive power and harmonics compensation. In
this paper, the SRF plan is used to generate current reference for
compensation and conventional PI controllers were used as the
controller to compensate the reactive power. The design of the closed
loop controllers is reserved simple by modeling them as first order
systems. Computationally uncomplicated and efficient SVM system
is used in the present work for better utilization of dc bus voltage.
The rating of shunt active filter has been finalized based on the
reactive power demand of the selected reactive load. The proposed
control and SVM technique are validated by simulating in MATLAB
software.
Abstract: Masonry infill walls are inevitable in the selfsupporting
structures, but their contribution in the resistance to
earthquake loads is generally neglected in the structural analyses. The
principal aim of this work through a numerical study of masonry
infill walls behavior in structures subjected to horizontal load is to
propose by finite elements numerical modeling, a more reliable
approach, faster and close to reality. In this study, 3D Finite Element
Analysis was developed to study the behavior of masonry infill walls
in structures subjected to horizontal load; the finite element software
being used was ABAQUS, it is observed that more rigidity of the
masonry filling is significant, more the structure is rigid, we can so
conclude that the filling brings an additional rigidity to the structure
not to be neglected; it is also observed that when the framework is
subjected to horizontal loads, the framework separates from the
filling on the level of the tended diagonal.
Abstract: This study focuses on a novel method for dispersion
and distribution of reinforcement under high intensive shear stress to
produce metal composites. The polyacrylonitrile (PAN)-based short
carbon fiber (Csf) and Nextel 610 alumina fiber were dispersed under
high intensive shearing at mushy zone in semi-solid of A356 by a
novel method. The bundles and clusters were embedded by
infiltration of slurry into the clusters, thus leading to a uniform
microstructure. The fibers were embedded homogenously into the
aluminum around 576-580°C with around 46% of solid fraction.
Other experiments at 615°C and 568°C which are contained 0% and
90% solid respectively were not successful for dispersion and
infiltration of aluminum into bundles of Csf. The alumina fiber has
been cracked by high shearing load. The morphologies and
crystalline phase were evaluated by SEM and XRD. The adopted
thixo-process effectively improved the adherence and distribution of
Csf into Al that can be developed to produce various composites by
thixomixing.
Abstract: Toddy sediment (TS) was cultured in a PDA medium
to determine initial yeast load, and also it was undergone sun, shade,
solar, dehumidified cold air (DCA) and hot air oven (at 400, 500 and
60oC) drying with a view to preserve viability of yeast. Thereafter,
this study was conducted according to two factor factorial design in
order to determine best preservation method. Therein the dried TS
from the best drying method was taken and divided into two portions.
One portion was mixed with 3: 7 ratio of TS: rice flour and the
mixture was divided in to two again. While one portion was kept
under in house condition the other was in a refrigerator. Same
procedure was followed to the rest portion of TS too but it was at the
same ratio of corn flour. All treatments were vacuum packed in triple
laminate pouches and the best preservation method was determined
in terms of leavening index (LI). The TS obtained from the best
preservation method was used to make foods (bread and hopper) and
organoleptic properties of it were evaluated against same of ordinary
foods using sensory panel with a five point hedonic scale.
Results revealed that yeast load or fresh TS was 58×106 CFU/g.
The best drying method in preserving viability of yeast was DCA
because LI of this treatment (96%) is higher than that of other three
treatments. Organoleptic properties of foods prepared from best
preservation method are as same as ordinary foods according to Duo
trio test.
Abstract: This paper presents the results of an experimental
study undertaken to evaluate the local bond stress-slip response of
short embedment of reinforcing bars in normal concrete (NC) and
high performance fiber reinforced cement composites (HPFRCC)
blocks. Long embedment was investigated as well to gain insights on
the distribution of strain, slip, bar stress and bond stress along the bar
especially in post-yield range. A total of 12 specimens were tested,
by means of pull-out of the reinforcing bars from concrete blocks. It
was found that the enhancement of local bond strength can be
reached up to 50% and ductility of the bond behavior was improved
significantly if HPFRCC is used. Also, under a constant strain at
loaded end, HPFRCC has delayed yielding of bars at other location
from the loaded end. Hence, the reduction of bond stress was slower
for HPFRCC in comparison with NC. Due to the same reason, the
total slips at loaded end for HPFRCC was smaller than NC as
expected. Test results indicated that HPFRCC has better bond slip
behavior which makes it a suitable material to be employed in
anchorage zone such as beam-column joints.