Abstract: This paper reports the influence of sucrose on the
preservation of CO2 hydrate crystal samples. The particle diameter of
hydrate samples were 1.0 and 5.6-8.0 mm. Mass fraction of sucrose in
the sample was 0.16. The samples were stored at the aerated condition
under atmospheric pressure and at the temperature of 253 or 258 K.
The results indicated that the mass fractions of CO2 hydrate in the
samples with sucrose were 0.10 ± 0.03 at the end of 3-week
preservation, regardless of temperature and particle diameter. Mass
fraction of CO2 hydrate in the samples with sucrose was higher than
that of pure CO2 hydrate for 1.0 mm particle diameter, while was
lower than that of pure CO2 hydrate for 5.6-8.0 mm particle diameter.
Discussion is made on the influence of sucrose on the dissociation of
CO2 hydrate and the resulting formation of ice.
Abstract: Turbulence studies were made in the wake of a rotating
circular cylinder in a uniform free stream. The interest was to
examine the turbulence properties at the suppression of periodicity in
vortex formation process. An experimental study of the turbulent near
wake of a rotating circular cylinder was made at a Reynolds number
of 9000 for velocity ratios, λ between 0 and 2.7. Hot-wire
anemometry and particle image velocimetry results indicate that the
rotation of the cylinder causes significant changes in the vortical
activities. The turbulence quantities are getting smaller as λ increases
due to suppression of coherent vortex structures.
Abstract: Direct fermentation of 226 white rose tapioca stem to
ethanol by Fusarium oxysporum was studied in a batch reactor.
Fermentation of ethanol can be achieved by sequential pretreatment
using dilute acid and dilute alkali solutions using 100 mesh tapioca
stem particles. The quantitative effects of substrate concentration, pH
and temperature on ethanol concentration were optimized using a full
factorial central composite design experiment. The optimum process
conditions were then obtained using response surface methodology.
The quadratic model indicated that substrate concentration of 33g/l,
pH 5.52 and a temperature of 30.13oC were found to be optimum for
maximum ethanol concentration of 8.64g/l. The predicted optimum
process conditions obtained using response surface methodology was
verified through confirmatory experiments. Leudeking-piret model
was used to study the product formation kinetics for the production
of ethanol and the model parameters were evaluated using
experimental data.
Abstract: In this study, synthesis of biomemitic patterned nano
hydroxyapatite-starch biocomposites using different concentration of
starch to evaluate effect of polymer alteration on biocomposites
structural properties has been reported. Formation of hydroxyapatite
nano particles was confirmed by X-ray diffraction (XRD) and Fourier
transform infrared spectroscopy (FT-IR). Size and morphology of the
samples were characterized using scanning and transmission electron
microscopy (SEM and TEM). It seems that by increasing starch
content, the more active site of polymer (oxygen atoms) can be
provided for interaction with Ca2+ followed by phosphate and
hydroxyl group.
Abstract: Design of Converter transformer insulation is a major
challenge. The insulation of these transformers is stressed by both
AC and DC voltages. Particle contamination is one of the major
problems in insulation structures, as they generate partial discharges
leading it to major failure of insulation. Similarly corona discharges
occur in transformer insulation. This partial discharge due to particle
movement / corona formation in insulation structure under different
voltage wave shapes, are different. In the present study, UHF
technique is adopted to understand the discharge activity and could
be realized that the characteristics of UHF signal generated under
low and high fields are different. In the case of corona generated
signal, the frequency content of the UHF sensor output lies in the
range 0.3-1.2 GHz and is not much varied except for its increase in
magnitude of discharge with the increase in applied voltage. It is
realized that the current signal injected due to partial
discharges/corona is about 4ns duration measured for first one half
cycle. Wavelet technique is adopted in the present study. It allows
one to identify the frequency content present in the signal at different
instant of time. The STD-MRA analysis helps one to identify the
frequency band in which the energy content of the UHF signal is
maximum.
Abstract: Motion control of flexible arms is more difficult than
that of rigid arms, however utilizing its dynamics enables improved
performance such as a fast motion in short operation time. This paper
investigates a ball throwing robot with one rigid link and one flexible
link. This robot throws a ball at a set speed with a proper control torque.
A mathematical model of this ball throwing robot is derived through
Hamilton’s principle. Several patterns of torque input are designed and
tested through the proposed simulation models. The parameters of
each torque input pattern is optimized and determined by chaos
embedded vector evaluated particle swarm optimization (CEVEPSO).
Then, the residual vibration of the manipulator after throwing is
suppressed with input shaping technique. Finally, a real experiment is
set up for the model checking.
Abstract: This paper deals with the experimental investigations
of the in-cylinder tumble flows in an unfired internal combustion
engine with a flat piston at the engine speeds ranging from 400 to
1000 rev/min., and also with the dome and dome-cavity pistons at an
engine speed of 1000 rev/min., using particle image velocimetry.
From the two-dimensional in-cylinder flow measurements, tumble
flow analysis is carried out in the combustion space on a vertical
plane passing through cylinder axis. To analyze the tumble flows,
ensemble average velocity vectors are used and to characterize it,
tumble ratio is estimated. From the results, generally, we have found
that tumble ratio varies mainly with crank angle position. Also, at the
end of compression stroke, average turbulent kinetic energy is more
at higher engine speeds. We have also found that, at 330 crank angle
position, flat piston shows an improvement of about 85 and 23% in
tumble ratio, and about 24 and 2.5% in average turbulent kinetic
energy compared to dome and dome-cavity pistons respectively
Abstract: We developed a new method based on quasimolecular
modeling to simulate the cavity flow in three cavity
shapes: rectangular, half-circular and bucket beer in cgs units. Each
quasi-molecule was a group of particles that interacted in a fashion
entirely analogous to classical Newtonian molecular interactions.
When a cavity flow was simulated, the instantaneous velocity vector
fields were obtained by using an inverse distance weighted
interpolation method. In all three cavity shapes, fluid motion was
rotated counter-clockwise. The velocity vector fields of the three
cavity shapes showed a primary vortex located near the upstream
corners at time t ~ 0.500 s, t ~ 0.450 s and t ~ 0.350 s, respectively.
The configurational kinetic energy of the cavities increased as time
increased until the kinetic energy reached a maximum at time t ~
0.02 s and, then, the kinetic energy decreased as time increased. The
rectangular cavity system showed the lowest kinetic energy, while
the half-circular cavity system showed the highest kinetic energy.
The kinetic energy of rectangular, beer bucket and half-circular
cavities fluctuated about stable average values 35.62 x 103, 38.04 x
103 and 40.80 x 103 ergs/particle, respectively. This indicated that the
half-circular shapes were the most suitable shape for a shrimp pond
because the water in shrimp pond flows best when we compared with
rectangular and beer bucket shape.
Abstract: The quantified residence time distribution (RTD)
provides a numerical characterization of mixing in a reactor, thus
allowing the process engineer to better understand mixing
performance of the reactor.This paper discusses computational
studies to investigate flow patterns in a two impinging streams
cyclone reactor(TISCR) . Flow in the reactor was modeled with
computational fluid dynamics (CFD). Utilizing the Eulerian-
Lagrangian approach, implemented in FLUENT (V6.3.22), particle
trajectories were obtained by solving the particle force balance
equations. From simulation results obtained at different Δts, the mean
residence time (tm) and the mean square deviation (σ2) were
calculated. a good agreement can be observed between predicted and
experimental data. Simulation results indicate that the behavior of
complex reactor systems can be predicted using the CFD technique
with minimum data requirement for validation.
Abstract: The dissolution of spherical particles in liquids is analyzed dynamically. Here, we consider the case the dissolution of solute yields a solute-free solid phase in the outer portion of a particle. As dissolution proceeds, the interface between the undissolved solid phase and the solute-free solid phase moves towards the center of the particle. We assume that there exist two resistances for the diffusion of solute molecules: the resistance due to the solute-free portion of the particle and that due to a surface layer near solid-liquid interface. In general, the equation governing the dynamic behavior of dissolution needs to be solved numerically. However, analytical expressions for the temporal variation of the size of the undissoved portion of a particle and the variation of dissolution time can be obtained in some special cases. The present analysis takes the effect of variable bulk solute concentration on dissolution into account.
Abstract: In the last decades to supply the various and different
demands of clients, a lot of manufacturers trend to use the mixedmodel
assembly line (MMAL) in their production lines, since this
policy make possible to assemble various and different models of the
equivalent goods on the same line with the MTO approach.
In this article, we determine the sequence of (MMAL) line, with
applying the kitting approach and planning of rest time for general
workers to reduce the wastages, increase the workers effectiveness
and apply the sector of lean production approach.
This Multi-objective sequencing problem solved in small size with
GAMS22.2 and PSO meta heuristic in 10 test problems and compare
their results together and conclude that their results are very similar
together, next we determine the important factors in computing the
cost, which improving them cost reduced. Since this problem, is NPhard
in large size, we use the particle swarm optimization (PSO)
meta-heuristic for solving it. In large size we define some test
problems to survey it-s performance and determine the important
factors in calculating the cost, that by change or improved them
production in minimum cost will be possible.
Abstract: The influence of extrusion parameters on surface
quality and properties of AA6061+x% vol. SiC (x = 0; 2,5; 5; 7,5;10)
composites was discussed in this paper. The averages size of
AA6061 and SiC particles were 10.6 μm and 0.42 μm, respectively.
Two series of composites (I - compacts were preheated at extrusion
temperature through 0.5 h and cooled by water directly after process;
II - compacts were preheated through 3 hours and were not cooled)
were consolidated via powder metallurgy processing and extruded by
KoBo method. High values of density for both series of composites
were achieved. Better surface quality was observed for II series of
composites. Moreover, for these composites lower (compared to I
series) but more uniform strength properties over the cross-section of
the bar were noticed. Microstructure and Young-s modulus
investigations were made.
Abstract: The dispersion of heavy particles line in an isotropic
and incompressible three-dimensional turbulent flow has been
studied using the Kinematic Simulation techniques to find out the
evolution of the line fractal dimension. In this study, the fractal
dimension of the line is found for different cases of heavy particles
inertia (different Stokes numbers) in the absence of the particle
gravity with a comparison with the fractal dimension obtained in the
diffusion case of material line at the same Reynolds number. It can
be concluded for the dispersion of heavy particles line in turbulent
flow that the particle inertia affect the fractal dimension of a line
released in a turbulent flow for Stokes numbers 0.02 < St < 2. At the
beginning for small times, most of the different cases are not affected
by the inertia until a certain time, the particle response time τa, with
larger time as the particles inertia increases, the fractal dimension of
the line increases owing to the particles becoming more sensitive to
the small scales which cause the change in the line shape during its
journey.
Abstract: This paper proposes the method combining artificial
neural network (ANN) with particle swarm optimization (PSO) to
implement the maximum power point tracking (MPPT) by controlling
the rotor speed of the wind generator. First, the measurements of wind
speed, rotor speed of wind power generator and output power of wind
power generator are applied to train artificial neural network and to
estimate the wind speed. Second, the method mentioned above is
applied to estimate and control the optimal rotor speed of the wind
turbine so as to output the maximum power. Finally, the result reveals
that the control system discussed in this paper extracts the maximum
output power of wind generator within the short duration even in the
conditions of wind speed and load impedance variation.
Abstract: Self-compacting concrete (SCC), a new kind of high
performance concrete (HPC) have been first developed in Japan in
1986. The development of SCC has made casting of dense
reinforcement and mass concrete convenient, has minimized noise.
Fresh self-compacting concrete (SCC) flows into formwork and
around obstructions under its own weight to fill it completely and
self-compact (without any need for vibration), without any
segregation and blocking. The elimination of the need for
compaction leads to better quality concrete and substantial
improvement of working conditions. SCC mixes generally have a
much higher content of fine fillers, including cement, and produce
excessively high compressive strength concrete, which restricts its
field of application to special concrete only. To use SCC mixes in
general concrete construction practice, requires low cost materials to
make inexpensive concrete.
Rice husk ash (RHA) has been used as a highly reactive
pozzolanic material to improve the microstructure of the interfacial
transition zone (ITZ) between the cement paste and the aggregate in
self compacting concrete. Mechanical experiments of RHA blended
Portland cement concretes revealed that in addition to the pozzolanic
reactivity of RHA (chemical aspect), the particle grading (physical
aspect) of cement and RHA mixtures also exerted significant
influences on the blending efficiency.
The scope of this research was to determine the usefulness of Rice
husk ash (RHA) in the development of economical self compacting
concrete (SCC). The cost of materials will be decreased by reducing
the cement content by using waste material like rice husk ash instead
of.
This paper presents a study on the development of Mechanical
properties up to 180 days of self compacting and ordinary concretes
with rice-husk ash (RHA), from a rice paddy milling industry in
Rasht (Iran). Two different replacement percentages of cement by
RHA, 10%, and 20%, and two different water/cementicious material
ratios (0.40 and 0.35), were used for both of self compacting and
normal concrete specimens. The results are compared with those of
the self compacting concrete without RHA, with compressive,
flexural strength and modulus of elasticity. It is concluded that RHA
provides a positive effect on the Mechanical properties at age after
60 days.
Base of the result self compacting concrete specimens have higher
value than normal concrete specimens in all test except modulus of
elasticity. Also specimens with 20% replacement of cement by RHA
have the best performance.
Abstract: The use of magnetic and magnetic/gold core/shell
nanoparticles in biotechnology or medicine has shown good promise
due to their hybrid nature which possesses superior magnetic and
optical properties. Some of these potential applications include
hyperthermia treatment, bio-separations, diagnostics, drug delivery
and toxin removal. Synthesis refinement to control geometric and
magnetic/optical properties, and finding functional surfactants for
biomolecular attachment, are requirements to meet application
specifics.
Various high-temperature preparative methods were used for the
synthesis of iron oxide and gold-coated iron oxide nanoparticles.
Different surface functionalities, such as 11-aminoundecanoic and
11-mercaptoundecanoic acid, were introduced on the surface of the
particles to facilitate further attachment of biomolecular functionality
and drug-like molecules. Nanoparticle thermal stability, composition,
state of aggregation, size and morphology were investigated and the
results from techniques such as Fourier Transform-Infra Red
spectroscopy (FT-IR), Ultraviolet visible spectroscopy (UV-vis),
Transmission Electron Microscopy (TEM) and thermal analysis are
discussed.
Abstract: In hydrocyclones, the particle separation efficiency is
limited by the suspended fine particles, which are discharged with the
coarse product in the underflow. It is well known that injecting water
in the conical part of the cyclone reduces the fine particle fraction in
the underflow. This paper presents a mathematical model that
simulates the water injection in the conical component. The model
accounts for the fluid flow and the particle motion. Particle
interaction, due to hindered settling caused by increased density and
viscosity of the suspension, and fine particle entrainment by settling
coarse particles are included in the model. Water injection in the
conical part of the hydrocyclone is performed to reduce fine particle
discharge in the underflow. The model demonstrates the impact of
the injection rate, injection velocity, and injection location on the
shape of the partition curve. The simulations are compared with
experimental data of a 50-mm cyclone.
Abstract: Fly ash is one of the residues generated in
combustion, and comprises the fine particles that rise with the flue
gases. Ash which does not rise is termed bottom ash [1]. In our
country, it is expected that will be occurred 50 million tons of waste
ash per year until 2020. Released waste from the thermal power
plants is caused very significant problems as known. The fly ashes
can be evaluated by using as adsorbent material.
The purpose of this study is to investigate the possibility of use of
Tuncbilek fly ash like low-cost adsorbents for heavy metal
adsorption. First of all, Tuncbilek fly ash was characterized. For this
purpose; analysis such as sieve analysis, XRD, XRF, SEM and FT-IR
were performed.
Abstract: An embedded system for SEU(single event upset) test
needs to be designed to prevent system failure by high-energy particles
during measuring SEU. SEU is a phenomenon in which the data is changed temporary in semiconductor device caused by high-energy particles. In this paper, we present an embedded system for
SRAM(static random access memory) SEU test. SRAMs are on the DUT(device under test) and it is separated from control board which
manages the DUT and measures the occurrence of SEU. It needs to
have considerations for preventing system failure while managing the
DUT and making an accurate measurement of SEUs. We measure the occurrence of SEUs from five different SRAMs at three different
cyclotron beam energies 30, 35, and 40MeV. The number of SEUs of SRAMs ranges from 3.75 to 261.00 in average.
Abstract: Motor imagery classification provides an important basis for designing Brain Machine Interfaces [BMI]. A BMI captures and decodes brain EEG signals and transforms human thought into actions. The ability of an individual to control his EEG through imaginary mental tasks enables him to control devices through the BMI. This paper presents a method to design a four state BMI using EEG signals recorded from the C3 and C4 locations. Principle features extracted through principle component analysis of the segmented EEG are analyzed using two novel classification algorithms using Elman recurrent neural network and functional link neural network. Performance of both classifiers is evaluated using a particle swarm optimization training algorithm; results are also compared with the conventional back propagation training algorithm. EEG motor imagery recorded from two subjects is used in the offline analysis. From overall classification performance it is observed that the BP algorithm has higher average classification of 93.5%, while the PSO algorithm has better training time and maximum classification. The proposed methods promises to provide a useful alternative general procedure for motor imagery classification