Abstract: A solar powered air heating system using one ended evacuated tubes is experimentally investigated. A solar air heater containing forty evacuated tubes is used for heating purpose. The collector surface area is about 4.44 m2. The length and outer diameters of the outer glass tube and absorber tube are 1500, 47 and 37 mm, respectively. In this experimental setup, we have a header (heat exchanger) of square shape (190 mm x 190 mm). The length of header is 1500 mm. The header consists of a hollow pipe in the center whose diameter is 60 mm through which the air is made to flow. The experimental setup contains approximately 108 liters of water. Water is working as heat collecting medium which collects the solar heat falling on the tubes. This heat is delivered to the air flowing through the header pipe. This heat flow is due to natural convection and conduction. The outlet air temperature depends upon several factors along with air flow rate and solar radiation intensity. The study has been done for both up-flow and down-flow of air in header in similar weather conditions, at different flow rates. In the present investigations the study has been made to find the effect of intensity of solar radiations and flow rate of air on the out let temperature of the air with time and which flow is more efficient. The obtained results show that the system is highly effective for the heating in this region. Moreover, it has been observed that system is highly efficient for the particular flow rate of air. It was also observed that downflow configuration is more effective than up-flow condition at all flow rates due to lesser losses in down-flow. The results show that temperature differences of upper head and lower head, both of water and surface of pipes on the respective ends is lower in down-flow.
Abstract: Using strength Pulse Electrical Field (PEF) in food
industries is a non-thermal process that can deactivate
microorganisms and increase penetration in plant and animals tissues
without serious impact on food taste and quality. In this paper designing and fabricating of a PEF generator has been presented. Pulse generation methods have been surveyed and the best of them
selected. The equipment by controller set can generate square pulse with adjustable parameters such as amplitude 1-5kV, frequency 0.1-10Hz, pulse width 10-100s, and duty cycle 0-100%. Setting the number of pulses, and presenting the output voltage and current
waveforms on the oscilloscope screen are another advantages of this
equipment. Finally, some food samples were tested that yielded the satisfactory results. PEF applying had considerable effects on potato, banana and purple cabbage. It caused increase Brix factor from 0.05
to 0.15 in potato solution. It is also so effective in extraction color material from purple cabbage. In the last experiment effects of PEF
voltages on color extraction of saffron scum were surveyed (about 6% increasing yield).
Abstract: In this work, the effects of scale on thermal behavior of the slab in a walking-beam type reheating furnace is studied by considering scale formation and growth in a furnace environment. Also, mathematical heat transfer model to predict the thermal radiation in a complex shaped reheating furnace with slab and skid buttons is developed with combined nongray WSGGM and blocked-off solution procedure. The model can attack the heat flux distribution within the furnace and the temperature distribution in the slab throughout the reheating furnace process by considering the heat exchange between the slab and its surroundings, including the radiant heat transfer among the slabs, the skids, the hot combustion gases and the furnace wall as well as the gas convective heat transfer in the furnace. With the introduction of the mathematical formulations validation of the present numerical model is conducted by calculating two example problems of blocked-off and nongray gas radiative heat transfer. After discussing the formation and growth of the scale on the slab surface, slab heating characteristics with scale is investigated in terms of temperature rise with time.
Abstract: The paper presents a numerical investigation on the
rapid gas decompression in pure nitrogen which is made by using the
one-dimensional (1D) and three-dimensional (3D) mathematical
models of transient compressible non-isothermal fluid flow in pipes.
A 1D transient mathematical model of compressible thermal multicomponent
fluid mixture flow in pipes is presented. The set of the
mass, momentum and enthalpy conservation equations for gas phase
is solved in the model. Thermo-physical properties of multicomponent
gas mixture are calculated by solving the Equation of
State (EOS) model. The Soave-Redlich-Kwong (SRK-EOS) model is
chosen. This model is successfully validated on the experimental data
[1] and shows a good agreement with measurements. A 3D transient
mathematical model of compressible thermal single-component gas
flow in pipes, which is built by using the CFD Fluent code (ANSYS),
is presented in the paper. The set of unsteady Reynolds-averaged
conservation equations for gas phase is solved. Thermo-physical
properties of single-component gas are calculated by solving the Real
Gas Equation of State (EOS) model. The simplest case of gas
decompression in pure nitrogen is simulated using both 1D and 3D
models. The ability of both models to simulate the process of rapid
decompression with a high order of agreement with each other is
tested. Both, 1D and 3D numerical results show a good agreement
between each other. The numerical investigation shows that 3D CFD
model is very helpful in order to validate 1D simulation results if the
experimental data is absent or limited.
Abstract: The Constraints imposed by non-thermal
leptogenesis on the survival of the neutrino mass models describing
the presently available neutrino mass patterns, are studied
numerically. We consider the Majorana CP violating phases coming
from right-handed Majorana mass matrices to estimate the baryon
asymmetry of the universe, for different neutrino mass models
namely quasi-degenerate, inverted hierarchical and normal
hierarchical models, with tribimaximal mixings. Considering two
possible diagonal forms of Dirac neutrino mass matrix as either
charged lepton or up-quark mass matrix, the heavy right-handed
mass matrices are constructed from the light neutrino mass matrix.
Only the normal hierarchical model leads to the best predictions of
baryon asymmetry of the universe, consistent with observations in
non-thermal leptogenesis scenario.
Abstract: The experimental results on combustion of rice husk
in a conical fluidized bed combustor (referred to as the conical FBC)
using silica sand as the bed material are presented in this paper. The
effects of excess combustion air and combustor loading as well as the
sand bed height on the combustion pattern in FBC were investigated.
Temperatures and gas concentrations (CO and NO) along over the
combustor height as well as in the flue gas downstream from the ash
collecting cyclone were measured. The results showed that the axial
temperature profiles in FBC were explicitly affected by the
combustor loading whereas the excess air and bed height were found
to have minor influences on the temperature pattern. Meanwhile, the
combustor loading and the excess air significantly affected the axial
CO and NO concentration profiles; however, these profiles were
almost independent of the bed height. The combustion and thermal
efficiencies for this FBC were quantified for different operating
conditions.
Abstract: So much energy is used in high rise buildings to fulfill
the basic needs of users such as lighting and thermal comfort.
Malaysia has hot and humid climate, buildings especially high rise
buildings receive unnecessary solar radiation that cause more solar
heat gain. Energy use specially electricity consumption in high rise
buildings has increased. There have been growing concerns about
energy consumption and its effect on environment. Building, energy
and the environment are important issues that the designers should
consider to them. Self protected form is one of possible ways against
the impact of solar radiation in high rise buildings. The Energy
performance of building envelopes was investigated in term of the
Overall Thermal Transfer Value (OTTV ).In this paper, the amount
of OTTV reduction was calculated through OTTV Equations to
clear the effectiveness of self shading strategy on minimizing energy
consumption for cooling interior spaces in high rise buildings which
has considerable envelope areas against solar radiation. Also increasing
the optimum window area was investigated using self-shading
strategy in designing high rise buildings. As result, the significant
reduction in OTTV was shown based on WWR.In addition slight
increase was demonstrated in WWR that can influence on visible
comfort interior spaces.
Abstract: An effort has been taken to simulate the combustion
and performance characteristics of biodiesel fuel in direct injection
(D.I) low heat rejection (LHR) diesel engine. Comprehensive
analyses on combustion characteristics such as cylinder pressure,
peak cylinder pressure, heat release and performance characteristics
such as specific fuel consumption and brake thermal efficiency are
carried out. Compression ignition (C.I) engine cycle simulation was
developed and modified in to LHR engine for both diesel and
biodiesel fuel. On the basis of first law of thermodynamics the
properties at each degree crank angle was calculated. Preparation and
reaction rate model was used to calculate the instantaneous heat
release rate. A gas-wall heat transfer calculations are based on the
ANNAND-s combined heat transfer model with instantaneous wall
temperature to analyze the effect of coating on heat transfer. The
simulated results are validated by conducting the experiments on the
test engine under identical operating condition on a turbocharged D.I
diesel engine. In this analysis 20% of biodiesel (derived from
Jatropha oil) blended with diesel and used in both conventional and
LHR engine. The simulated combustion and performance
characteristics results are found satisfactory with the experimental
value.
Abstract: In the context of large volume Big Divisor (nearly)
SLagy D3/D7 μ-Split SUSY [1], after an explicit identification
of first generation of SM leptons and quarks with fermionic superpartners
of four Wilson line moduli, we discuss the identification of
gravitino as a potential dark matter candidate by explicitly calculating
the decay life times of gravitino (LSP) to be greater than age of
universe and lifetimes of decays of the co-NLSPs (the first generation
squark/slepton and a neutralino) to the LSP (the gravitino) to be
very small to respect BBN constraints. Interested in non-thermal
production mechanism of gravitino, we evaluate the relic abundance
of gravitino LSP in terms of that of the co-NLSP-s by evaluating
their (co-)annihilation cross sections and hence show that the former
satisfies the requirement for a potential Dark Matter candidate. We
also show that it is possible to obtain a 125 GeV light Higgs in our
setup.
Abstract: Internal combustion engines rejects 30-40% of the
energy supplied by fuel to the environment through exhaust gas. thus, there is a possibility for further significant improvement of efficiency with the utilization of exhaust gas energy and its conversion to mechanical energy or electrical energy. The Thermo-Electric
Generator (TEG) will be located in the exhaust system and will make use of an energy flow between the warmer exhaust gas and the external environment. Predict to th optimum position of temperature
distribution and the performance of TEG through numerical analysis.
The experimental results obtained show that the power output significantly increases with the temperature difference between cold
and hot sides of a thermoelectric generator.
Abstract: We investigate properties of convective solutions of the
Boussinesq thermal convection in a moderately rotating spherical
shell allowing the inner and outer sphere rotation due to the viscous
torque of the fluid. The ratio of the inner and outer radii of the
spheres, the Prandtl number and the Taylor number are fixed to 0.4,
1 and 5002, respectively. The inertial moments of the inner and outer
spheres are fixed to about 0.22 and 100, respectively. The Rayleigh
number is varied from 2.6 × 104 to 3.4 × 104. In this parameter
range, convective solutions transit from equatorially symmetric quasiperiodic
ones to equatorially asymmetric chaotic ones as the Rayleigh
number is increased. The transition route in the system allowing
rotation of both the spheres is different from that in the co-rotating
system, which means the inner and outer spheres rotate with the
same constant angular velocity: the convective solutions transit as
equatorially symmetric quasi-periodic solution → equatorially symmetric
chaotic solution → equatorially asymmetric chaotic solution
in the system allowing both the spheres rotation, while equatorially
symmetric quasi-periodic solution → equatorially asymmetric quasiperiodic
solution → equatorially asymmetric chaotic solution in the
co-rotating system.
Abstract: Thermally insulating ceramic coatings also known as
thermal barrier coatings (TBCs) have been essential technologies to
improve the performance and efficiency of advanced gas turbines in
service at extremely high temperatures. The damage mechanisms of
air-plasma sprayed YSZ thermal barrier coatings (TBC) with various
microstructures were studied by microscopic techniques after thermal
cycling. The typical degradation of plasma TBCs that occurs during
cyclic furnace testing of an YSZ and alumina coating on a Titanium
alloy are analyzed. During the present investigation the effects of
topcoat thickness, bond coat oxidation, thermal cycle lengths and test
temperature are investigated using thermal cycling. These results
were correlated with stresses measured by a spectroscopic technique
in order to understand specific damage mechanism. The failure
mechanism of former bond coats was found to involve fracture
initiation at the thermally grown oxide (TGO) interface and at the
TGO bond coat interface. The failure mechanism of the YZ was
found to involve combination of fracture along the interface between
TGO and bond coat.
Abstract: In this paper a three dimensional thermal model of a
power toroidal transformer is proposed for both steady-state or
transient conditions. The influence of electric current and ambient
temperature on the temperature distribution, has been investigated.
To validate the three dimensional thermal model, some experimental
tests have been done. There is a good correlation between
experimental and simulation results.
Abstract: The paper presents the results of theoretical and
numerical modeling of propagation of shock waves in bubbly liquids
related to nonlinear effects (realistic equation of state, chemical
reactions, two-dimensional effects). On the basis on the Rankine-
Hugoniot equations the problem of determination of parameters of
passing and reflected shock waves in gas-liquid medium for
isothermal, adiabatic and shock compression of the gas component is
solved by using the wide-range equation of state of water in the
analitic form. The phenomenon of shock wave intensification is
investigated in the channel of variable cross section for the
propagation of a shock wave in the liquid filled with bubbles
containing chemically active gases. The results of modeling of the
wave impulse impact on the solid wall covered with bubble layer are
presented.
Abstract: The paper presents a one-dimensional transient
mathematical model of compressible non-isothermal multicomponent
fluid mixture flow in a pipe. The set of the mass,
momentum and enthalpy conservation equations for gas phase is
solved in the model. Thermo-physical properties of multi-component
gas mixture are calculated by solving the Equation of State (EOS)
model. The Soave-Redlich-Kwong (SRK-EOS) model is chosen. Gas
mixture viscosity is calculated on the basis of the Lee-Gonzales-
Eakin (LGE) correlation. Numerical analysis of rapid gas
decompression process in rich and base natural gases is made on the
basis of the proposed mathematical model. The model is successfully
validated on the experimental data [1]. The proposed mathematical
model shows a very good agreement with the experimental data [1] in
a wide range of pressure values and predicts the decompression in
rich and base gas mixtures much better than analytical and
mathematical models, which are available from the open source
literature.
Abstract: The paper presents an optimization study based on
genetic algorithms (GA-s) for a radio-frequency applicator used in
heating dielectric band products. The weakly coupled electro-thermal
problem is analyzed using 2D-FEM. The design variables in the
optimization process are: the voltage of a supplementary “guard"
electrode and six geometric parameters of the applicator. Two
objective functions are used: temperature uniformity and total active
power absorbed by the dielectric. Both mono-objective and multiobjective
formulations are implemented in GA optimization.
Abstract: In the present paper, the three-dimensional
temperature field of tool is determined during the machining and
compared with experimental work on C45 workpiece using carbide
cutting tool inserts. During the metal cutting operations, high
temperature is generated in the tool cutting edge which influence on
the rate of tool wear. Temperature is most important characteristic of
machining processes; since many parameters such as cutting speed,
surface quality and cutting forces depend on the temperature and high
temperatures can cause high mechanical stresses which lead to early
tool wear and reduce tool life. Therefore, considerable attention is
paid to determine tool temperatures. The experiments are carried out
for dry and orthogonal machining condition. The results show that
the increase of tool temperature depends on depth of cut and
especially cutting speed in high range of cutting conditions.
Abstract: this study was carried out to investigate the changes in
quality parameters of rye bread packaged in different polymer films
during convection air-flow thermal treatment process. Whole loafs of
bread were placed in polymer pouches, which were sealed in reduced
pressure air ambiance, bread was thermally treated in
at temperature +(130; 140; and 150) ± 5 ºC within 40min, as long as
the core temperature of the samples have reached accordingly
+80±1 ºC. For bread packaging pouches were used: anti-fog
Mylar®OL12AF and thermo resistant combined polymer material.
Main quality parameters was analysed using standard methods:
temperature in bread core, bread crumb and crust firmness value,
starch granules volume and microflora. In the current research it was
proved, that polymer films significantly influence rye bread quality
parameters changes during thermal treatment. Thermo resistant
combined polymer material film could be recommendable for
packaged rye bread pasteurization, for maximal bread quality
parameter keeping.
Abstract: In this study, we discussed the effects on the thermal
comfort of super high-rise residences that how effected by the high
thermal capacity structural components. We considered different
building orientations, structures, and insulation methods. We used the
dynamic simulation software THERB (simulation of the thermal
environment of residential buildings). It can estimate the temperature,
humidity, sensible temperature, and heating/cooling load for multiple
buildings. In the past studies, we examined the impact of
air-conditioning loads (hereinafter referred to as AC loads) on the
interior structural parts and the AC-usage patterns of super-high-rise
residences.
Super-high-rise residences have more structural components such
as pillars and beams than do ordinary apartment buildings. The
skeleton is generally made of concrete and steel, which have high
thermal-storage capacities. The thermal-storage capacity of
super-high-rise residences is considered to have a larger impact on the
AC load and thermal comfort than that of ordinary residences.
We show that the AC load of super-high-rise units would be
reduced by installing insulation on the surfaces of interior walls that
are not usually insulated in Japan.
Abstract: The Lattice Boltzmann Method (LBM) with double populations is applied to solve the steady-state laminar natural convective heat transfer in a triangular cavity filled with water. The bottom wall is heated, the vertical wall is cooled, and the inclined wall is kept adiabatic. The buoyancy effect was modeled by applying the Boussinesq approximation to the momentum equation. The fluid velocity is determined by D2Q9 LBM and the energy equation is discritized by D2Q4 LBM to compute the temperature field. Comparisons with previously published work are performed and found to be in excellent agreement. Numerical results are obtained for a wide range of parameters: the Rayleigh number from to and the inclination angle from 0° to 360°. Flow and thermal fields were exhibited by means of streamlines and isotherms. It is observed that inclination angle can be used as a relevant parameter to control heat transfer in right-angled triangular enclosures.