Abstract: The aim of this study is to analyze influence of
differences of heat insulation methods on indoor thermal environment and comfort of apartment buildings.
This study analyzes indoor thermal environment and comfort on units of apartment buildings using calculation software "THERB" and
compares three different kinds of heat insulation methods. Those are
outside insulation on outside walls, inside insulation on outside walls and interior insulation. In terms of indoor thermal environment, outside insulation is the best to stabilize room temperature. In winter, room temperature on
outside insulation after heating is higher than other and it is kept 3-5 degrees higher through all night. But the surface temperature with
outside insulation did not dramatically increase when heating was used, which was 3 to 5oC lower than the temperature with other
insulation. The PMV of interior insulation fall nearly range of comfort when the heating and cooling was use.
Abstract: In this paper a novel method was presented for
evaluating the fabric pills using digital image processing techniques. This work provides a novel technique for
detecting pills and also measuring their heights, surfaces and
volumes. Surely, measuring the intensity of defects by human vision is an inaccurate method for quality control; as a result, this problem became a motivation for employing digital image processing techniques for detection of defects of fabric
surface. In the former works, the systems were just limited to measuring of the surface of defects, but in the presented
method the height and the volume of defects were also
measured, which leads to a more accurate quality control. An algorithm was developed to first, find pills and then measure their average intensity by using three criteria of height, surface
and volume. The results showed a meaningful relation
between the number of rotations and the quality of pilled fabrics.
Abstract: The main objectives of this paper are to measure
pollutants concentrations in the oil refinery area in Kuwait over three
periods during one year, obtain recent emission inventory for the
three refineries of Kuwait, use AERMOD and the emission inventory
to predict pollutants concentrations and distribution, compare model
predictions against measured data, and perform numerical
experiments to determine conditions at which emission rates and the
resulting pollutant dispersion is below maximum allowable limits.
Abstract: Mechanical and water transport properties of high
performance concrete (HPC) containing natural zeolite as partial
replacement of Portland cement are studied. Experimental results
show that in the investigated mixes the use of natural zeolite leads to
an increase of porosity, decrease of compressive strength and
increase of moisture diffusivity and water vapor diffusion coefficient,
as compared with the reference HPC. However, for the replacement
level up to 20% of the mass of Portland cement the concretes still
maintain their high performance character and exhibit acceptable
water transport properties. Therefore, natural zeolite can be
considered an environmental friendly binder with a potential to
replace a part of Portland cement in concrete in building industry.
Abstract: Knowledge about the magnetic quantities in a magnetic circuit is always of great interest. On the one hand, this information is needed for the simulation of a transformer. On the other hand, parameter studies are more reliable, if the magnetic quantities are derived from a well established model. One possibility to model the 3-phase transformer is by using a magnetic equivalent circuit (MEC). Though this is a well known system, it is often not an easy task to set up such a model for a large number of lumped elements which additionally includes the nonlinear characteristic of the magnetic material. Here we show the setup of a solver for a MEC and the results of the calculation in comparison to measurements taken. The equations of the MEC are based on a rearranged system of the nodal analysis. Thus it is possible to achieve a minimum number of equations, and a clear and simple structure. Hence, it is uncomplicated in its handling and it supports the iteration process. Additional helpful tasks are implemented within the solver to enhance the performance. The electric circuit is described by an electric equivalent circuit (EEC). Our results for the 3-phase transformer demonstrate the computational efficiency of the solver, and show the benefit of the application of a MEC.
Abstract: A theoretical study is conducted to design and explore
the effect of different parameters such as heat loads, the tube size of
piping system, wick thickness, porosity and hole size on the
performance and capability of a Loop Heat Pipe(LHP). This paper
presents a steady state model that describes the different phenomena
inside a LHP. Loop Heat Pipes(LHPs) are two-phase heat transfer
devices with capillary pumping of a working fluid. By their original
design comparing with heat pipes and special properties of the
capillary structure, they-re capable of transferring heat efficiency for
distances up to several meters at any orientation in the gravity field,
or to several meters in a horizontal position. This theoretical model is
described by different relations to satisfy important limits such as
capillary and nucleate boiling. An algorithm is developed to predict
the size of the LHP satisfying the limitations mentioned above for a
wide range of applied loads. Finally, to assess and evaluate the
algorithm and all the relations considered, we have used to design a
new kind of LHP to recover the heat from the exhaust of an actual
Gas Turbine. By finding the results, it showed that we can use the
LHP as a very high efficient device to recover the heat even in high
amount of loads(exhaust of a gas turbine). The sizes of all parts of the
LHP were obtained using the developed algorithm.
Abstract: Switched-mode converters play now a significant role in
modern society. Their operation are often crucial in various electrical
applications affecting the every day life. Therefore, the quality of
the converters needs to be reliably verified. Recent studies have
shown that the converters can be fully characterized by a set of
frequency responses which can be efficiently used to validate the
proper operation of the converters. Consequently, several methods
have been proposed to measure the frequency responses fast and
accurately. Most often correlation-based techniques have been applied.
The presented measurement methods are highly sensitive to
external errors and system nonlinearities. This fact has been often
forgotten and the necessary uncertainty analysis of the measured
responses has been neglected. This paper presents a simple approach
to analyze the noise and nonlinearities in the frequency-response
measurements of switched-mode converters. Coherence analysis is
applied to form a confidence interval characterizing the noise and
nonlinearities involved in the measurements. The presented method is
verified by practical measurements from a high-frequency switchedmode
converter.
Abstract: Producing companies aspire to high delivery
availability despite appearing disruptions. To ensure high delivery
availability safety stocksare required. Howeversafety stock leads to
additional capital commitment and compensates disruptions instead
of solving the reasons.The intention is to increase the stability in
production by configuring the production planning and control
systematically. Thus the safety stock can be reduced. The largest
proportion of inventory in producing companies is caused by batch
inventory, schedule deviations and variability of demand rates.These
reasons for high inventory levels can be reduced by configuring the
production planning and control specifically. Hence the inventory
level can be reduced. This is enabled by synchronizing the lot size
straightening the demand as well as optimizing the releasing order,
sequencing and capacity control.
Abstract: Masonry cavity walls are loaded by wind pressure and vertical load from upper floors. These loads results in bending moments and compression forces in the ties connecting the outer and the inner wall in a cavity wall. Large cavity walls are furthermore loaded by differential movements from the temperature gradient between the outer and the inner wall, which results in critical increase of the bending moments in the ties. Since the ties are loaded by combined compression and moment forces, the loadbearing capacity is derived from instability equilibrium equations. Most of them are iterative, since exact instability solutions are complex to derive, not to mention the extra complexity introducing dimensional instability from the temperature gradients. Using an inverse variable substitution and comparing an exact theory with an analytical instability solution a method to design tie-connectors in cavity walls was developed. The method takes into account constraint conditions limiting the free length of the wall tie, and the instability in case of pure compression which gives an optimal load bearing capacity. The model is illustrated with examples from praxis.
Abstract: The main focus of this paper is on the human induced
forces. Almost all existing force models for this type of load (defined
either in the time or frequency domain) are developed from the
assumption of perfect periodicity of the force and are based on force
measurements conducted on rigid (i.e. high frequency) surfaces. To
verify the different authors conclusions the vertical pressure
measurements invoked during the walking was performed, using
pressure gauges in various configurations. The obtained forces are
analyzed using Fourier transformation. This load is often decisive in
the design of footbridges. Design criteria and load models proposed
by widely used standards and other researchers were introduced and a
comparison was made.
Abstract: Numerous experimental tests for post-installed anchor systems drilled in hardened concrete were conducted in order to estimate pull-out and shear strength accounting for uncertainties such as torque ratios, embedment depths and different diameters in demands. In this study, the strength of the systems was significantly changed by the effect of those three uncertainties during pull-out experimental tests, whereas the shear strength of the systems was not affected by torque ratios. It was also shown that concrete cone failure or damage mechanism was generally investigated during and after pull-out tests and in shear strength tests, mostly the anchor systems were failed prior to failure of primary structural system. Furthermore, 3D finite element model for the anchor systems was created by ABAQUS for the numerical analysis. The verification of finite element model was identical till the failure points to the load-displacement relationship specified by the experimental tests.
Abstract: Corrugated wire mesh laminates (CWML) are a class
of engineered open cell structures that have potential for applications
in many areas including aerospace and biomedical engineering. Two
different methods of fabricating corrugated wire mesh laminates from
stainless steel, one using a high temperature Lithobraze alloy and the
other using a low temperature Eutectic solder for joining the
corrugated wire meshes are described herein. Their implementation is
demonstrated by manufacturing CWML samples of 304 and 316
stainless steel (SST). It is seen that due to the facility of employing
wire meshes of different densities and wire diameters, it is possible to
create CWML laminates with a wide range of effective densities. The
fabricated laminates are tested under uniaxial compression. The
variation of the compressive yield strength with relative density of the
CWML is compared to the theory developed by Gibson and Ashby for
open cell structures [22]. It is shown that the compressive strength of
the corrugated wire mesh laminates can be described using the same
equations by using an appropriate value for the linear coefficient in the
Gibson-Ashby model.
Abstract: Nylon 6-clay hybrid/neat nylon 6, sheath/core
bicomponent nanocomposite fibers containing 4 wt% of clay in
sheath section were melt spun at different take-up speeds. Their
orientation and crystalline structure were compared to those of neat
nylon 6 fibers. Birefringence measurements showed that the
orientation development in sheath and core parts of bicomponent
fibers was different. Crystallinity results showed that clay did not act
as a nucleating agent for bicomponent fibers. The neat nylon 6 fiber
had a smooth surface while striped pattern was appeared on the
surface of bicomponent fiber containing clay due to thermal
shrinkage of the core part.
Abstract: This paper generalizes Yeh Lam-s shock model for
renewal shock arrivals and random threshold. Several interesting
statistical measures are explicitly obtained. A few special cases and
an optimal replacement problem are also discussed.
Abstract: This work describes refrigeration effects during storage on total protein and amino acids composition of raw and processed flour of two pearl millet cultivars (Ashana and Dembi). The protein content of the whole raw flour was found to be 14.46 and 13.38% for Ashana and Dembi cultivars, respectively. Dehulling of the grains reduced the protein content to 13.38 and 12.67% for the cultivars, respectively. For both cultivars, the protein content of the whole and dehulled raw flour before and after cooking was slightly decreased when the flour was stored for 60 days even after refrigeration. The effect of refrigeration process in combination with the storage period, cooking or dehulling was found to be vary between amino acids and even between cultivars. Regardless of the storage period and processing method, the amino acids content was remained unchanged after refrigeration for both cultivars.
Abstract: Segmentation in ultrasound images is challenging due to the interference from speckle noise and fuzziness of boundaries. In this paper, a segmentation scheme using fuzzy c-means (FCM) clustering incorporating both intensity and texture information of images is proposed to extract breast lesions in ultrasound images. Firstly, the nonlinear structure tensor, which can facilitate to refine the edges detected by intensity, is used to extract speckle texture. And then, a spatial FCM clustering is applied on the image feature space for segmentation. In the experiments with simulated and clinical ultrasound images, the spatial FCM clustering with both intensity and texture information gets more accurate results than the conventional FCM or spatial FCM without texture information.
Abstract: Both prognostic and diagnostic modes of a 3D baroclinic
model in hydrodynamic and sediment transport models of
the Princeton Ocean Model (POM) were conducted to separate
prognose and diagnose effects of different hydrodynamic factors on
transport of suspended sediment discharged from the rivers to the
Gulf of Thailand (GoT). Both transport modes of suspended sediment
distribution in the GoT were numerically simulated. It could be
concluded that the suspended sediment discharged from the rivers
around the GoT. Most of sediments in estuaries and coastal areas are
deposited outside the GoT under the condition of wind-driven current,
and very small amount of the sediments of them are transported
faraway. On the basis of wind forcing, sediments from the lower
GoT to the upper GoT are mainly transported south-northwestward
and also continuously moved north-southwestward. An obvious 3D
characteristic of suspended sediment transport is produced in the
wind-driven current residual circulation condition. In this study, the
transport patterns at the third layer are generally consistent with
the typhoon-induced strong currents in two case studies of Typhoon
Linda 1997. The case studies presented the prognostic and diagnostic
modes during 00UTC28OCT1997 to 12UTC06NOV1997 in a short
period with the current condition for pre-operation of the suspended
sediment transport model in estuaries and coastal areas.
Abstract: The adoption of e-learning in Hong Kong has been
increasing rapidly in the past decade. To understand the e-learning
experiences of the students, the School of Professional and Continuing
Education of The University of Hong Kong conducted a survey. The
survey aimed to collect students- experiences in using learning
management system, their perceived e-learning advantages, barriers in
e-learning and preferences in new e-learning development. A
questionnaire with 84 questions was distributed in mid 2012 and 608
valid responds were received. The analysis results showed that the
students found e-learning helpful to their study. They preferred
interactive functions and mobile features. Blended learning mode,
both face-to-face learning mode integrated with online learning and
face-to-face learning mode supplemented with online resources, were
preferred by the students. The results of experiences of Hong Kong
students in e-learning provided a contemporary reference to the
e-learning practitioners to understand the e-learning situation in Asia.
Abstract: A numerical investigation has carried out to understand the melting characteristics of phase change material (PCM) in a fin type latent heat storage with the addition of embedded aluminum spiral fillers. It is known that melting performance of PCM can be significantly improved by increasing the number of embedded metallic fins in the latent heat storage system but to certain values where only lead to small improvement in heat transfer rate. Hence, adding aluminum spiral fillers within the fin gap can be an option to improve heat transfer internally. This paper presents extensive computational visualizations on the PCM melting patterns of the proposed fin-spiral fillers configuration. The aim of this investigation is to understand the PCM-s melting behaviors by observing the natural convection currents movement and melting fronts formation. Fluent 6.3 simulation software was utilized in producing twodimensional visualizations of melting fractions, temperature distributions and flow fields to illustrate the melting process internally. The results show that adding aluminum spiral fillers in Fin type latent heat storage can promoted small but more active natural convection currents and improve melting of PCM.
Abstract: In managing healthcare logistics, cost is not the only
factor to be considered. The level of items- criticality used in patient
care services plays an important role as well. A stock-out incident of
a high critical item could threaten a patient's life. In this paper, the
DMAIC (Define-Measure-Analyze-Improve-Control) methodology is
used to drive improvement projects based on customer driven critical
to quality characteristics at a Jordanian hospital. This paper shows
how the application of Six Sigma improves the performance of the
case hospital logistics system by reducing the number of stock-out
incidents.